High-efficiency dye-sensitized solar cells based on robust and both-end-open TiO2 nanotube membranes

In the present work, dye-sensitized solar cells (DSSCs) were fabricated by incorporating transparent electrodes of ordered free-standing TiO₂ nanotube (TNT) arrays with both ends open transferred onto fluorine-doped tin oxide (FTO) conductive glass. The high-quality TiO₂ membranes used here were obtained by a self-detaching technique, with the superiorities of facile but reliable procedures. Afterwards, these TNT membranes can be easily transferred to FTO glass substrates by TiO₂ nanoparticle paste without any crack. Compared with those DSSCs consisting of the bottom-closed membranes or attached to Ti substrate, the carefully assembled and front-side illuminated DSSCs showed an enhanced solar energy conversion efficiency as high as 5.32% of 24-μm-thick TiO₂ nanotube membranes without further treatments. These results reveal that by facilitating high-quality membrane synthesis, this kind of DSSCs assembly with optimized tube configuration can have a fascinating future.     

Quasi solid state dye-sensitized solar cells with modified TiO2 photoelectrodes and triphenylamine-based dye

Quasi solid state dye-sensitized solar cells (DSSCs) have been fabricated with organic sol or TiCl₄ modified TiO₂ and porous TiO₂ photoanode and a triphenylamine-based dye (TPAR3) used as photosensitizer. Dark current measurements suggested that both modified TiO₂ photoelectrodes had significantly reduced the recombination rate of photoelectrons due to the reduced bare FTO surface in comparison to porous photoelectrode. The DSSC based on modified TiO₂ photoelectrodes showed improved photovoltaic parameters compared to the porous TiO₂ photoelectrode. The overall power conversion efficiency (PCE) is 3.27%, 4.73% and 6.8% for porous, TiCl₄ modified and sol modified TiO₂ photoelectrodes, respectively. The improved PCE with modified TiO₂ electrodes was attributed to the formation of a compact layer. This effectively improves adherence of TiO₂ to FTO surface, providing a larger TiO₂/FTO contact area and reducing the electron recombination by blocking the direct contact between redox electrolyte and the conductive FTO surface and enhances the electron collection efficiency.     

Ga-doped ZnO transparent electrodes with TiO<Subscript>2</Subscript> blocking layer/nanoparticles for dye-sensitized solar cells

Ga-doped ZnO [GZO] thin films were employed for the transparent electrodes in dye-sensitized solar cells [DSSCs]. The electrical property of the deposited GZO films was as good as that of commercially used fluorine-doped tin oxide [FTO]. In order to protect the GZO and enhance the photovoltaic properties, a TiO₂ blocking layer was deposited on the GZO surface. Then, TiO₂ nanoparticles were coated on the blocking layer, and dye was attached for the fabrication of DSSCs. The fabricated DSSCs with the GZO/TiO₂ glasses showed an enhanced conversion efficiency of 4.02% compared to the devices with the normal GZO glasses (3.36%). Furthermore, they showed better characteristics even than those using the FTO glasses, which can be attributed to the reduced charge recombination and series resistance.     

An efficient and low-cost TiO2 compact layer for performance improvement of dye-sensitized solar cells

A TiO₂ organic sol was synthesised for the preparation of a compact TiO₂ layer on fluorine-doped tin oxide (FTO) glass by a dip-coating technique. The resultant thin film was used for the fabrication of dye-sensitized solar cells (DSSCs). The compact layer typically has a thickness of ca. 110 nm as indicated by its SEM, and consists of anatase as confirmed by the XRD pattern. Compared with the traditional DSSCs without this compact layer, the solar energy-to-electricity conversion efficiency, short-circuit current and open-circuit potential of the DSSCs with the compact layer were improved by 33.3%, 20.3%, and 10.2%, respectively. This can be attributed to the merits brought by the compact layer. It can effectively improve adherence of TiO₂ to FTO surface, provide a larger TiO₂/FTO contact area, and reduce the electron recombination by blocking the direct contact between the redox electrolyte and the conductive FTO surface.     

Efficient Performance of Electrostatic Spray-Deposited TiO2 Blocking Layers in Dye-Sensitized Solar Cells after Swift Heavy Ion Beam Irradiation

A compact TiO₂ layer (~1.1 μm) prepared by electrostatic spray deposition (ESD) and swift heavy ion beam (SHI) irradiation using oxygen ions onto a fluorinated tin oxide (FTO) conducting substrate showed enhancement of photovoltaic performance in dye-sensitized solar cells (DSSCs). The short circuit current density (J_sc = 12.2 mA cm^-2) of DSSCs was found to increase significantly when an ESD technique was applied for fabrication of the TiO₂ blocking layer, compared to a conventional spin-coated layer (J_sc = 8.9 mA cm^-2). When SHI irradiation of oxygen ions of fluence 1 × 10¹³ ions/cm² was carried out on the ESD TiO₂, it was found that the energy conversion efficiency improved mainly due to the increase in open circuit voltage of DSSCs. This increased energy conversion efficiency seems to be associated with improved electronic energy transfer by increasing the densification of the blocking layer and improving the adhesion between the blocking layer and the FTO substrate. The adhesion results from instantaneous local melting of the TiO₂ particles. An increase in the electron transport from the blocking layer may also retard the electron recombination process due to the oxidized species present in the electrolyte. These findings from novel treatments using ESD and SHI irradiation techniques may provide a new tool to improve the photovoltaic performance of DSSCs.     

Optimization of the dye-sensitized solar cell performance by mechanical compression

In this study, the P25 titanium dioxide (TiO₂) nanoparticle (NP) thin film was coated on the fluorine-doped tin oxide (FTO) glass substrate by a doctor blade method. The film then compressed mechanically to be the photoanode of dye-sensitized solar cells (DSSCs). Various compression pressures on TiO₂ NP film were tested to optimize the performance of DSSCs. The mechanical compression reduces TiO₂ inter-particle distance improving the electron transport efficiency. The UV–vis spectrophotometer and electrochemical impedance spectroscopy (EIS) were employed to quantify the light-harvesting efficiency and the charge transport impedance at various interfaces in DSSC, respectively. The incident photon-to-current conversion efficiency was also monitored. The results show that when the DSSC fabricated by the TiO₂ NP thin film compressed at pressure of 279 kg/cm², the minimum resistance of 9.38 Ω at dye/TiO₂ NP/electrolyte interfaces, the maximum short-circuit photocurrent density of 15.11 mA/cm², and the photoelectric conversion efficiency of 5.94% were observed. Compared to the DSSC fabricated by the non-compression of TiO₂ NP thin film, the overall conversion efficiency is improved over 19.5%. The study proves that under suitable compression pressure the performance of DSSC can be optimized.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Flexible photoanodes of TiO2 particles and metallic single-walled carbon nanotubes for flexible dye-sensitized solar cells

Recent advance in flexible electronics demands development of flexible energy sources. Of particular interests are flexible dye-sensitized solar cells (DSCs). However, a brittle nature of TiO₂ materials is one of hurdles to realize flexible DSCs. Here we synthesized flexible photoanodes of TiO₂ particles and single-walled carbon nanotubes (SWNTs). Metallic SWNTs provided a greater photovoltaic conversion efficiency than semiconducting SWNTs due to the more efficient electron transport. The metallic SWNTs also constructed effective mechanical network among TiO₂ particles providing flexibility and durability. The photoanode was transferred on an indium tin oxide (ITO)-coated polyethylene terephthalate film and characterized for front-illuminated DSCs under the AM 1.5 simulated sunlight. There was only a small decrease in photovoltaic conversion efficiency with bending which was primarily caused by cracking of the ITO layer. Due to this limitation, the TiO₂–metallic SWNT photoanode was transferred on a Ti foil and went through up to 1000 bending cycles. The cycled photoanode was assembled for back-illuminated DSCs due to the non-transparent Ti foil. There was no decrease in photovoltaic conversion efficiency even after 1000 bending cycles demonstrating excellent flexibility and durability.     

Enhancement of photoelectric conversion by high-voltage electric field assisted crystallization of a novel ternary-encapsulated spherical TiO2 aggregate for solar cells

A novel ternary-encapsulated spherical TiO₂ aggregate (TES-TiO₂) with submicron particle sizes was formed by blending commercial P25 TiO₂ and two different sizes of TiO₂ particles (synthesized by modified sol-gel and hydrothermal methods). A double-layered TiO₂ electrode for dye-sensitized solar cells (DSSCs) was fabricated by depositing TES-TiO₂ particles onto nanocrystalline mesoporous TiO₂ (Meso-TiO₂)-coated FTO glass by a cathodic electrophoresis technique and then calcined at 450 °C for 30 min. Compared to double-layered Meso-TiO₂/P25 electrodes, the energy conversion efficiency (η) of DSSCs from the obtained Meso-TiO₂/TES-TiO₂ electrode was improved by 9.3%, from 5.94% to 6.49%. When the prepared double-layered Meso-TiO₂/TES-TiO₂ electrode was calcined at high temperature, a high-voltage electric field (HVEF) was introduced to assist crystallization. As a result, η was further enhanced by 8.6%, from 6.49% to 7.05%. Notably, compared to typical 20 nm TiO₂ nanocrystallites applied in the active layer of DSSCs, the prepared loosely porous TES-TiO₂ with submicron size increased the light-scattering effect and promoted dye molecule adsorption and the diffusion of electrolytes. In addition, introduction of the HVEF provided better connection among TiO₂ particles, which facilitated electron transport and avoided charge recombination.     

Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

Conversion enhancement of flexible dye-sensitized solar cells based on TiO2 nanotube arrays with TiO2 nanoparticles by electrophoretic deposition

We prepared highly ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F⁻ containing electrolyte. The thickness and dye loading amount of TNAs were 26 μm and 1.06 × 10⁻⁷ mol cm⁻², respectively. TiO₂ nanoparticles (TNPs) were electrophoretically deposited on the inner wall of nanotube to produce coated nanotube arrays (TNAP). The dye loading was increased to 1.56 × 10⁻⁷ mol cm⁻², and the electron transport rate improved. TNAs and TNAP were sensitized with ruthenium dye N3 to yield dye-sensitized TiO₂ nanotube solar cells. The power conversion efficiency of TNA-based dye-sensitized solar cells (DSSCs) was 4.28%, whereas the efficiency of TNAP-based DSSCs increased to 6.28% when illuminated from the counter electrode. The increase of power conversion efficiency of TNAP-based DSSCs is ascribed to the increased surface area of TNAs and the faster electron transport rate.     

Preparation of TiO<Subscript>2</Subscript> nanotube/nanoparticle composite particles and their applications in dye-sensitized solar cells

Efficiency of dye-sensitized solar cells [DSSCs] was enhanced by combining the use of TiO₂ nanotubes [TNTs] and nanoparticles. TNTs were fabricated by a sol-gel method, and TiO₂ powders were produced through an alkali hydrothermal transformation. DSSCs were constructed using TNTs and TiO₂ nanoparticles at various weight percentages. TNTs and TiO₂ nanoparticles were coated onto FTO glass by the screen printing method. The DSSCs were fabricated using ruthenium(II) (N-719) and electrolyte (I₃/I₃ ^-) dyes. The crystalline structure and morphology were characterized by X-ray diffraction and using a scanning electron microscope. The absorption spectra were measured using an UV-Vis spectrometer. The incident photocurrent conversion efficiency was measured using a solar simulator (100 mW/cm²). The DSSCs based on TNT/TiO₂ nanoparticle hybrids showed better photovoltaic performance than cells made purely of TiO₂ nanoparticles.     

Enhancement of the photoelectric performance of dye-sensitized solar cells using Ag-doped TiO<Subscript>2</Subscript> nanofibers in a TiO<Subscript>2</Subscript> film as electrode

For high solar conversion efficiency of dye-sensitized solar cells [DSSCs], TiO₂ nanofiber [TN] and Ag-doped TiO₂ nanofiber [ATN] have been extended to be included in TiO₂ films to increase the amount of dye loading for a higher short-circuit current. The ATN was used on affected DSSCs to increase the open circuit voltage. This process had enhanced the exit in dye molecules which were rapidly split into electrons, and the DSSCs with ATN stop the recombination of the electronic process. The conversion efficiency of TiO₂ photoelectrode-based DSSCs was 4.74%; it was increased to 6.13% after adding 5 wt.% ATN into TiO₂ films. The electron lifetime of DSSCs with ATN increased from 0.29 to 0.34 s and that electron recombination was reduced.     

Low temperature preparation of a high performance Pt/SWCNT counter electrode for flexible dye-sensitized solar cells

A platinum/single-wall carbon nanotube (Pt/SWCNT) film was sprayed onto a flexible indium-doped tin oxide coated polyethylene naphthalate (ITO/PEN) substrate to form a counter electrode for use in a flexible dye-sensitized solar cell using a vacuum thermal decomposition method at low temperature (120 °C). The obtained Pt/SWCNT electrode showed good chemical stability and light transmittance and had lower charge transfer resistance and higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction compared to the flexible Pt electrode or a commercial Pt/Ti electrode. The light-to-electric energy conversion efficiency of the flexible DSSC based on the Pt/SWCNT/ITO/PEN counter electrode and the TiO₂/Ti photoanode reached 5.96% under irradiation with a simulated solar light intensity of 100 mW cm⁻². The efficiency was increased by 25.74% compared to the flexible DSSC with an unmodified Pt counter electrode.     

A natural tomato slurry as a photosensitizer for dye-sensitized solar cells with TiO2/CuO composite thin films

We have studied the performance of dye-sensitized solar cells by employing natural dye “anthocyanins” extracted from the tomato slurry as a sensitizer for the TiO₂/CuO photoanode. The extracts were anchored on TiO₂/CuO films deposited on an ITO substrate which was used as a photoanode. The dye adsorbed TiO₂/CuO films electrode, the copper plate as a counter electrode, and iodolyte as an electrolyte were assembled into DSSCs. The conversion efficiency of the DSSCs was found to be 2.96% with a V_OC of 0.615 V, J_SC of 6.6 mA/cm², and an FF of 0.73. This work highlights the use of contribution of the tomato slurry as a natural sensitizer to enhance the efficiency of DSSCs.     

Polyvinyl pyrrolidone aided preparation of TiO2 films used in flexible dye-sensitized solar cells

Polyvinyl pyrrolidone (PVP) is introduced to low temperature preparation of a good quality TiO₂ film used in flexible dye-sensitized solar cells (DSSCs). The samples are characterized by scanning electron microscopy and UV–vis absorption spectra, the photovoltaic performance of the DSSC is measured. It is found that PVP can improve the dispersion of TiO₂ particles and the adherence of TiO₂ particles to flexible substrate, as well as the adsorption of sensitized dye to TiO₂ film. Additionally, ultraviolet light irradiation can eliminate organics remained on the surface the TiO₂ film and improve the surface state of TiO₂ film. Under an optimal condition, a flexible DSSC using TiO₂ film doped PVP and UV irradiation treated achieves a light-to-electric energy conversion efficiency of 3.02% under irradiation with a simulate solar light intensity of 100 mW cm⁻².     

Improved electrochemical performance of dye-sensitized solar cell via surface modifications of the working electrode by electrodeposition

Modifications of the working electrode with TiO₂ blocking or coating layers are carried by electrodeposition in TiCl₃ precursor solution. The results suggest that the electrodeposited TiO₂ blocking layer provides excellent agglutination between the FTO substrate and the active TiO₂ layer. In addition, the electrodeposited TiO₂ coating layer enhances the interconnections between the TiO₂ nanoparticles and the FTO substrate, and therefore it increases the electron transport efficiency. The morphology and crystalline structure of the electrodeposited TiO₂ layers are characterized by SEM, TEM, and XRD. The electrochemical impedance spectroscopy measurements show that the improved DSSC performance with the electrodeposited coating layer is mainly due to the increase in the lifetime of the conduction band electron in the TiO₂ film. The photoelectron conversion efficiency of DSSC is increased from 3.47% to 5.38% by employing the TiO₂ electrodeposited working electrode.     

A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO₂ nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO₂-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq⁻¹ and is low enough to be used as an electrode. The surface morphologies of TiO₂-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE''s. This new fabricated device with TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%).     

Tuning substrate roughness to improve uniform growth and photocurrent response in anodic TiO2 nanotube arrays

Here we report on the effect of Ti substrate surface roughness on the morphology of anodized TiO₂ nanotube arrays (TNAs), as well as their crystal structure and photocurrent response measured in the backside illuminated dye-sensitized solar cells (DSSCs). TNAs grown on Ti substrates with higher roughness exhibited a non-uniform morphology, which encompassed both thick and thin-walled nanotubes. Reduction of the substrate roughness by different polishing methods causes the morphology of all of nanotubes to become uniform with thin wall thickness. Moreover, the compressive strain was reduced by decreasing the roughness according to the X-ray diffraction patterns. DSSCs fabricated using TNAs grown on the smoothest substrate showed a significantly higher conversion efficiency than that of the TNAs grown on the roughest substrate by a factor of 100%. Furthermore, TNAs grown on the smoothest substrate showed higher electron lifetime and lower recombination. Therefore, it has an enhancing effect on the photocurrent response of the anodized TNAs in backside illuminated DSSCs.     

Improvement of performance of dye-sensitized solar cells based on electrodeposited-platinum counter electrode

Platinum nanoparticle was electrodeposited on FTO conducting glass substrate as counter electrode for application in dye-sensitized solar cells (DSSCs). Images of transmission electron microscope (TEM) and Scanning Electron Microscope (SEM) showed that platinum nanoparticle was with the mean size of 20-30 nm and was homogeneously distributed on the surface of the FTO conductive glass sheet. Using such a counter electrode, DSSC showed a 6.40% overall energy conversion efficiency under one sun illumination. It exhibited the same high-performance as the DSSC with a platinum counter electrode prepared by electroplating. Furthermore, the present preparation method for the platinum counter electrode has the advantage of low platinum loading and transparence.