Preparation and electrochemical performance of Li4Ti5O12/carbon/carbon nano-tubes for lithium ion battery

A Li₄Ti₅O₁₂/carbon/carbon nano-tubes (Li₄Ti₅O₁₂/C/CNTs) composite was synthesized by using a solid-state method. For comparison, a Li₄Ti₅O₁₂/carbon (Li₄Ti₅O₁₂/C) composite and a pristine Li₄Ti₅O₁₂ were also synthesized in the present study. The microstructure and morphology of the prepared samples are characterized by XRD and SEM. Electrochemical properties of the samples are evaluated by using galvanostatic discharge/charge tests and AC impedance spectroscopy. The results reveal that the Li₄Ti₅O₁₂/C/CNTs composite exhibits the best rate capability and cycling stability among the samples of Li₄Ti₅O₁₂, Li₄Ti₅O₁₂/C and Li₄Ti₅O₁₂/C/CNTs. At the charge-discharge rate of 0.5 C, 5.0 C and 10.0 C, its discharge capacities were 163 mAh/g, 148 mAh/g and 143 mAh/g, respectively. After 100 cycles at 5.0 C, it remained at 146 mAh/g.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.     

Optimum synthesis of Li2Fe1−xMnxSiO4/C cathode for lithium ion batteries

Li₂Fe_1−xMn_xSi0₄/C cathode materials were synthesized by mechanical activation-solid-state reaction. The effects of Mn-doping content, roasting temperature, soaking time and Li/Si molar ratio on the physical properties and electrochemical performance of the Li₂Fe_1−xMn_xSi0₄/C composites were investigated. The materials were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM), charge-discharge tests and AC impedance measurements. SEM images suggest that the morphology of the Li₂Fe_1−xMn_xSi0₄/C composite is sensitive to the reaction temperature. Samples synthesized at different temperatures have different extent of agglomeration. Being charged-discharged at C/32 between 1.5 and 4.8 V, the Li₂Fe_0.9Mn_0.1Si0₄/C synthesized at the optimum conditions shows good electrochemical performances with an initial discharge capacity of 158.1 mAh g⁻¹ and a capacity retention ratio of 94.3% after 30 cycles. AC impendence investigation shows Li₂Fe_0.9Mn_0.1SiO₄/C have much lower resistance of electrode/electrolyte interface than Li₂FeSiO₄/C.     

The study of lithium ion de-insertion/insertion in LiMn2O4 and determination of kinetic parameters in aqueous Li2SO4 solution using electrochemical impedance spectroscopy

In this work, we report a basic study on the mechanism of lithium ion de-insertion/insertion process from/into LiMn₂O₄ cathode material in aqueous Li₂SO₄ solution using electrochemical impedance spectroscopy (EIS). An equivalent circuit distinguishing the kinetic parameters of lithium ion de-insertion/insertion is used to simulate the experimental impedance data. The fitting results are in good agreement with the experimental results and the parameters of the kinetic process of Li⁺ de-insertion and insertion in LiMn₂O₄ at different potentials during charge and discharge are obtained using the same circuit. The results indicate that the de-insertion/insertion behavior of lithium ions at LiMn₂O₄ cathode in Li₂SO₄ aqueous solution is similar to that reported in the organic electrolytes. The charge transfer resistance (R_ct), warburg resistance, double layer capacitance and chemical diffusion coefficient (DLi+) vary with potentials during de-insertion/insertion processes. R_ct is lowest at the CV peak potentials and the important kinetic parameter, DLi+ exhibits two distinct minima at potentials corresponding to CV peaks during de-insertion–insertion and it was found to be between 10⁻⁸ and 10⁻¹⁰ cm² s⁻¹during lithium de-insertion/insertion processes.     

A promising sol-gel route based on citric acid to synthesize Li3V2(PO4)3/carbon composite material for lithium ion batteries

Li₃V₂(PO₄)₃/carbon composite material was synthesized by a promising sol-gel route based on citric acid using V₂O₅ powder as a vanadium source. Citric acid acts not only as a chelating reagent but also as a carbon source, which enhance the conductivity of the composite material and hinder the growth of Li₃V₂(PO₄)₃ particles. The structure and morphology of the sample were characterized by TG, XRD and TEM measurements. XRD results reveal that Li₃V₂(PO₄)₃/carbon was successfully synthesized and has a monoclinic structure with space group P2₁/n. TEM images show Li₃V₂(PO₄)₃ particles are about 45 nm in diameter embeded in carbon networks. Galvanostatic charge/discharge and cyclic voltammetry measurements were used to study its electrochemical behaviors which indicate the reversibility of the lithium extraction/insertion processes. Li₃V₂(PO₄)₃/carbon performed in a voltage window (3.0-4.8 V) exhibits higher discharge capacity, better cycling stability and its discharge capacity maintains about 167.6 mAh/g at a current density of 28 mA/g after 50 cycles.     

Regeneration and characterization of air-exposed Li2FeSiO4

The air-exposed Li₂FeSiO₄ was characterized and regenerated by calcination under argon. The original Li₂FeSiO₄ was prepared by a sol–gel method and was then exposed in air for a year. The impact of long-term air exposure on the structure, surface and electrochemical characteristics of Li₂FeSiO₄ was investigated. In comparison with the original sample, the air-exposed sample was seriously oxidized. The oxidation speed decreases with increasing air-exposure time. The oxidization of Li₂FeSiO₄ led to surface change and deteriorated electrochemical performance. However, the changes induced by air exposure were entirely reversible. The one year air-exposed Li₂FeSiO₄ was regenerated by calcination under Argon. The regeneration conditions including calcination temperature and calcination time were optimized. The sample regenerated by calcining at 700 °C for 4 h had similar structure, surface and electrochemical characteristics to the original sample. Based on detailed analysis, the possible regeneration mechanisms were proposed.     

Cycling-induced stress in lithium ion negative electrodes: LiAl/LiFePO4 and Li4Ti5O12/LiFePO4 cells

In this work, we examined the electrochemical behaviour of lithium ion batteries containing lithium iron phosphate as the positive electrode and systems based on Li-Al or Li-Ti-O as the negative electrode. These two systems differ in their potential versus the redox couple Li⁺/Li and in their morphological changes upon lithium insertion/deinsertion. Under relatively slow charge/discharge regimes, the lithium-aluminium alloys were found to deliver energies as high as 438 Wh kg⁻¹ but could withstand only a few cycles before crumbling, which precludes their use as negative electrodes. Negative electrodes consisting solely of aluminium performed even worse. However, an electrode made from a material with zero-strain associated to lithium introduction/removal such as a lithium titanate spinel exhibited good performance that was slightly dependent on the current rate used. The Li₄Ti₅O₁₂/LiFePO₄ cell provided capacities as high as 150 mAh g⁻¹ under C-rate in the 100th cycle.     

All solid-state lithium polymer secondary batteries using spinel Li4/3Ti5/3O4 as an active material

Present paper describes electrochemical performance of the all solid-state lithium polymer battery (LBP) using spinel-type Li_4/3Ti_5/3O₄ which has been known as the potential candidate of anode materials.The assembled LPB with Li|solid polymer electrolyte(SPE)|Li_4/3Ti_5/3O₄ construction showed stable charge-discharge cycles more than 300 times at 1 C condition. On the other hand, strong charge-discharge rate dependence for the specific capacity and initial capacity loss was indicated. Such a poor rate performance stemmed from low diffusivity of Li⁺ ion in the by-products produced by the decomposition of SPE components at the SPE|Li_4/3Ti_5/3O₄ interface.     

Influence of composite LiCl-KCl molten salt on microstructure and electrochemical performance of spinel Li4Ti5O12

A series of spinel Li₄Ti₅O₁₂ samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li₄Ti₅O₁₂. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li₄Ti₅O₁₂ with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li₄Ti₅O₁₂ with L = 1.5 has an initial discharge capacity of 169 mAh g⁻¹ and an initial charge-discharge efficiency of 94% at 0.2 C rate, and achieves good rate performances from 0.2 C to 5 C.     

Electrochemical performance of Li3V2(PO4)3/C cathode material using a novel carbon source

Polyethylene glycol (PEG, mean molecular weight of 10,000) has been used to prepare a Li₃V₂(PO₄)₃/C cathode material by a simple solid-state reaction. The Raman spectra shows that the coating carbon has a good structure with a low I_D/I_G ratio. The images of SEM and TEM show that the carbon is dispersed between the Li₃V₂(PO₄)₃ particles, which improves the electrical contact between the corresponding particles. The electronic conductivity of Li₃V₂(PO₄)₃/C composite is 7.0 × 10⁻¹ S/cm, increased by seven orders of magnitude compared with the pristine Li₃V₂(PO₄)₃ (2.3 × 10⁻⁸ S/cm). At a low discharge rate of 0.28C, the sample presents a high discharge capacity of 131.2 mAh/g, almost achieving the theoretical capacity (132 mAh/g) for the reversible cycling of two lithium. After 500 cycles, the discharge capacity is 123.9 mAh/g with only 5.6% fading of the initial specific capacity. The Li₃V₂(PO₄)₃/C material also exhibits an excellent rate capability with high discharge capacities of 115.2 mAh/g at 1C and 106.4 mAh/g at 5C.     

Preparation and electrochemical performance studies on Cr-doped Li3V2(PO4)3 as cathode materials for lithium-ion batteries

Cr-doped Li₃V_2−xCr_x(PO₄)₃/C (x = 0, 0.05, 0.1, 0.2, 0.5, 1) compounds have been prepared using sol–gel method. The Rietveld refinement results indicate that single-phase Li₃V_2−xCr_x(PO₄)₃/C with monoclinic structure can be obtained. Although the initial specific capacity decreased with Cr content at a lower current rate, both cycle performance and rate capability have excited improvement with moderate Cr-doping content in Li₃V_2−xCr_x(PO₄)₃/C. Li₃V_1.9Cr_0.1(PO₄)₃/C compound presents an initial capacity of 171.4 mAh g⁻¹ and 78.6% capacity retention after 100 cycles at 0.2C rate. At 4C rate, the Li₃V_1.9Cr_0.1(PO₄)₃/C can give an initial capacity of 130.2 mAh g⁻¹ and 10.8% capacity loss after 100 cycles where the Li₃V₂(PO₄)₃/C presents the initial capacity of 127.4 mAh g⁻¹ and capacity loss of 14.9%. Enhanced rate and cyclic capability may be attributed to the optimizing particle size, carbon coating quality, and structural stability during the proper amount of Cr-doping (x = 0.1) in V sites.     

Rheological phase reaction synthesis and electrochemical performance of Li3V2(PO4)3/carbon cathode for lithium ion batteries

Monoclinic lithium vanadium phosphate/carbon (Li₃V₂(PO₄)₃/C) cathode has been synthesized for applications in lithium ion batteries, via a rheological phase reaction (RPR) method. The sample is characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). This material exhibits high initial discharge capacity of 189 and 177 mAh g⁻¹ at 0.1 and 0.2 C between 3.0 and 4.8 V, respectively. Moreover, it displays good fast rate performance, which discharge capacities of 140, 133, 129 and 124 mAh g⁻¹ can be delivered after 100 cycles between 3.0 and 4.8 V vs. Li at a different rate of 0.5, 1, 2 and 5 C, respectively. The electrochemical impedance spectroscopy (EIS) is also investigated.     

Study on synthesis routes and their influences on chemical and electrochemical performances of Li3V2(PO4)3/carbon

In this study, Li₃V₂(PO₄)₃/carbon samples were synthesized by two different synthesis routes. Their influence on chemical and electrochemical performances of Li₃V₂(PO₄)₃/carbon as cathode materials for lithium-ion batteries was investigated. The structure and morphology of Li₃V₂(PO₄)₃/carbon were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM) measurements. TEM revealed that the Li₃V₂(PO₄)₃ grains synthesized through the sol-gel route had a depressed grain size. Electrochemical behaviors were characterized by galvanostatic charge/discharge, cyclic voltammetry and AC impedance measurements. Li₃V₂(PO₄)₃/carbon with smaller grain size showed better performances in terms of the discharge capacity and cycle stability. The improved electrochemical properties of the Li₃V₂(PO₄)₃/carbon were attributed to the depressed grain size and enhanced electrical contacts produced via the sol-gel route. AC impedance measurements also showed that the sol-gel route significantly decreased the charge-transfer resistance and shortened the migration distance of lithium ion.     

锂离子电池硅酸锰锂电极材料的研究进展

具有斜方晶系结构的硅酸锰锂（LizMnSi04）是近年来备受关注的锂离子电池正极材料,作者详细叙述了近年来国内外对Li2MnSiO4研究状况,着重介绍了各种制备方法和改性方法,其中溶胶凝胶法是目前应用最多的制备方法,而掺杂改性的方法是目前比较有效的改性方法。同时还介绍了这些方法所存在的问题。     

Effects of carbon source and carbon content on electrochemical performances of Li4Ti5O12/C prepared by one-step solid-state reaction

Li₄Ti₅O₁₂/C composites were synthesized by one-step solid-state reaction method using four commonly used organic compounds or organic polymers as carbon source, i.e., polyacrylate acid (PAA), citric acid (CA), maleic acid (MA) and polyvinyl alcohol (PVA). The physical characteristics of Li₄Ti₅O₁₂/C composites were investigated by X-ray diffraction, electron microscopy, Raman spectroscopy, particle size distribution and thermogravimetry-derivative thermogravimetry techniques. Their electrochemical properties were characterized by cyclic voltammograms, electrochemical impedance spectra, constant current charge–discharge and rate charge–discharge. These analyses indicated that the carbon source and carbon content have a great effect on the physical and electrochemical performances of Li₄Ti₅O₁₂/C composites. An ideal carbon source and appropriate carbon content effectively improved the electrical contact between the Li₄Ti₅O₁₂ particles, which enhanced the discharge capacity and rate capability of Li₄Ti₅O₁₂/C composites. PAA was the best carbon source for the synthesis of Li₄Ti₅O₁₂/C composites. When the carbon content was 3.49 wt.% (LiOH·H₂O/PAA molar ratio of 1), as-prepared Li₄Ti₅O₁₂/C showed the maximum discharge capacity. At 0.2 C, initial capacity of the optimized sample was 168.6 mAh g⁻¹ with capacity loss of 2.8% after 50 cycles. At 8 and 10 C, it showed discharge capacities of 143.5 and 132.7 mAh g⁻¹, with capacity loss of 8.7 and 9.9% after 50 cycles, respectively.     

Structure and electrochemical performance of nanostructured Fe3O4/carbon nanotube composites as anodes for lithium ion batteries

Polyvinyl alcohol (PVA) was used as a hydrogen bond functionalizing agent to modify multi-walled carbon nanotubes (CNTs). Nanoparticles of Fe₃O₄ were then formed along the sidewalls of the as-modified CNTs by the chemical coprecipitation of Fe²⁺ and Fe³⁺ in the presence of CNTs in an alkaline solution. The structure and electrochemical performance of the Fe₃O₄/CNTs nanocomposite electrodes have been investigated in detail. Electrochemical tests indicated that at the 145th cycle, the CNTs-66.7 wt.%Fe₃O₄ nanocomposite electrode can deliver a high discharge capacity of 656 mAh g⁻¹ and stable cyclic retention. The improvement of reversible capacity and cyclic performance of the Fe₃O₄/CNTs nanocomposite could be attributed to the nanosized Fe₃O₄ particles and the network of CNTs.     

Effects of Cr doping on the electrochemical properties of Li2FeSiO4 cathode material for lithium-ion batteries

Cr-doped Li₂FeSiO₄ was prepared by a sol-gel method. The effects of Cr doping on the characteristics of Li₂FeSiO₄ were carefully investigated. Compared with the XRD pattern of the Li₂FeSiO₄ sample, the XRD patterns of the Cr-doped samples have no extra reflections. This indicates that Cr enters the structure of Li₂FeSiO₄ rather than forming impurities. As indicated by the charge-discharge measurements, the highest capacity is obtained by 3% Cr doping. The particle size of the Li₂Fe_0.97Cr_0.03SiO₄ sample was smaller than that of the Li₂FeSiO₄ sample, and the BET surface area of the Li₂Fe_0.97Cr_0.03SiO₄ sample was more than twice as high as that of the Li₂FeSiO₄ sample. Compared with the Li₂FeSiO₄ sample, the Li₂Fe_0.97Cr_0.03SiO₄ sample shows faster activation, higher reversible capacity, and better rate capability, which can be attributed to the smaller particle size and larger surface area as well as the crystal defects induced by Cr doping.     

Structure and electrochemical properties of nanocarbon-coated Li3V2(PO4)3 prepared by sol-gel method

A liquid-based sol-gel method was developed to synthesize nanocarbon-coated Li₃V₂(PO₄)₃. The products were characterized by XRD, SEM and electrochemical measurements. The results of Rietveld refinement analysis indicate that single-phase Li₃V₂(PO₄)₃ with monoclinic structure can be obtained in our experimental process. The discharge capacity of carbon-coated Li₃V₂(PO₄)₃ was 152.6 mAh/g at the 50th cycle under 1C rate, with 95.4% retention rate of initial capacity. A high discharge capacity of 184.1 mAh/g can be obtained under 0.12C rate, and a capacity of 140.0 mAh/g can still be held at 3C rate. The cyclic voltammetric measurements indicate that the electrode reaction reversibility is enhanced due to the carbon-coating. SEM images show that the reduced particle size and well-dispersed carbon-coating can be responsible for the good electrochemical performance obtained in our experiments.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Electrochemical properties of TiP2O7 and LiTi2(PO4)3 as anode material for lithium ion battery with aqueous solution electrolyte

Some polyanionic compounds, e.g. TiP₂O₇ and LiTi₂(PO₄)₃ with 3D framework structure were proposed to be used as anodes of lithium ion battery with aqueous electrolyte. The cyclic voltammetry properties TiP₂O₇ and LiTi₂(PO₄)₃ suggested that Li-ion de/intercalation reaction can occur without serious hydrogen evolution in 5 M LiNO₃ aqueous solution. The TiP₂O₇ and LiTi₂(PO₄)₃ give capacities of about 80 mAh/g between potentials of −0.50 V and 0 V (versus SHE) and 90 mAh/g between −0.65 V and −0.10 V (versus SHE), respectively. A test cell consisting of TiP₂O₇/5 M LiNO₃/LiMn₂O₄ delivers approximately 42 mAh/g (weight of cathode and anode) at average voltage of 1.40 V, and LiTi₂(PO₄)₃/5 M LiNO₃/LiMn₂O₄ delivers approximately 45 mAh/g at average voltage of 1.50 V. Both as-assembled cells suffered from short cycle life. The capacity fading may be related to deterioration of anode material.