Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

High-rate characteristics of novel anode Li4Ti5O12/polyacene materials for Li-ion secondary batteries

In recent years, spinel lithium titanate (Li₄Ti₅O₁₂) as a superior anode material for energy storage battery has attracted a great deal of attention because of the excellent Li-ion insertion and extraction reversibility. However, the high-rate characteristics of this material should be improved if it is used as an active material in large batteries. One effective way to achieve this is to prepare electrode materials coated with carbon. A Li₄Ti₅O₁₂/polyacene (PAS) composite were first prepared via an in situ carbonization of phenol-formaldehyde (PF) resin route to form carbon-based composite. The SEM showed that the Li₄Ti₅O₁₂ particles in the composite were more rounded and smaller than the pristine one. The PAS was uniformly dispersed between the Li₄Ti₅O₁₂ particles, which improved the electrical contact between the corresponding Li₄Ti₅O₁₂ particles, and hence the electronic conductivity of composite material. The electronic conductivity of Li₄Ti₅O₁₂/PAS composite is 10⁻¹ S cm⁻¹, which is much higher than 10⁻⁹ S cm⁻¹ of the pristine Li₄Ti₅O₁₂. High specific capacity, especially better high-rate performance was achieved with this Li₄Ti₅O₁₂/PAS electrode material. The initial specific capacity of the sample is 144 mAh/g at 3 C, and it is still 126.2 mAh/g after 200 cycles. By increasing the current density, the sample still maintains excellent cycle performance.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Synthesis and electrochemical performance of Li2FeSiO4/carbon/carbon nano-tubes for lithium ion battery

Li₂FeSiO₄/carbon/carbon nano-tubes (Li₂FeSiO₄/C/CNTs) and Li₂FeSiO₄/carbon (Li₂FeSiO₄/C) composites were synthesized by a traditional solid-state reaction method and characterized comparatively by X-ray diffraction, scanning electron microscopy, BET surface area measurement, galvanostatic charge-discharge and AC impedance spectroscopy, respectively. The results revealed that the Li₂FeSiO₄/C/CNT composite exhibited much better rate performance in comparison with the Li₂FeSiO₄/C composite. At 0.2 C, 5 C and 10 C, the former composite electrode delivered a discharge capacity of 142 mAh g⁻¹, 95 mAh g⁻¹, 80 mAh g⁻¹, respectively, and after 100 cycles at 1 C, the discharge capacity remained 95.1% of its initial value.     

Preparation and characterization of nano-particle LiFePO4 and LiFePO4/C by spray-drying and post-annealing method

Pure, nano-sized LiFePO₄ and LiFePO₄/C cathode materials are synthesized by spray-drying and post-annealing method. The influence of the sintering temperature and carbon coating on the structure, particle size, morphology and electrochemical performance of LiFePO₄ cathode material is investigated. The optimum processing conditions are found to be thermal treatment for 10 h at 600 °C. Compared with LiFePO₄, LiFePO₄/C particles are smaller in size due to the inhibition of crystal growth to a great extent by the presence of carbon in the reaction mixture. And that the LiFePO₄/C composite coated with 3.81 wt.% carbon exhibits the best electrode properties with discharge capacities of 139.4, 137.2, 133.5 and 127.3 mAh g⁻¹ at C/5, 1C, 5C and 10C rates, respectively. In addition, it shows excellent cycle stability at different current densities. Even after 50 cycles at the high current density of 10C, a discharge capacity of 117.7 mAh g⁻¹ is obtained (92.4% of its initial value) with only a low capacity fading of 0.15% per cycle.     

Properties of Li-graphite and LiFePO4 electrodes in LiPF6–sulfolane electrolyte

Sulfolane (also referred to as tetramethylene sulfone, TMS) containing LiPF₆ and vinylene carbonate (VC) was tested as a non-flammable electrolyte for a graphite |LiFePO₄ lithium-ion battery. Charging/discharging capacity of the LiFePO₄ electrode was ca. 150 mAh g⁻¹ (VC content 5 wt%). The capacity of the graphite electrode after 10 cycles establishes at the level of ca. 350 mAh g⁻¹ (C/10 rate). In the case of the full graphite |1 M LiPF₆ + TMS + VC 10 wt% |LiFePO₄ cell, both charging and discharging capacity (referred to cathode mass) stabilized at a value of ca. 120 mAh g⁻¹. Exchange current density for Li⁺ reduction on metallic lithium, estimated from electrochemical impedance spectroscopy (EIS) experiments, was j_o(Li/Li⁺) = 8.15 × 10⁻⁴ A cm⁻². Moreover, EIS suggests formation of the solid electrolyte interface (SEI) on lithium, lithiated graphite and LiFePO₄ electrodes, protecting them from further corrosion in contact with the liquid electrolyte. Scanning electron microscopy (SEM) images of pristine electrodes and those taken after electrochemical cycling showed changes which may be interpreted as a result of SEI formation. No graphite exfoliation was observed. The main decomposition peak of the LiPF₆ + TMS + VC electrolyte (TG/DTA experiment) was present at ca. 275 °C. The LiFePO₄(solid) + 1 M LiPF₆ + TMS + 10 wt% VC system shows a flash point of ca. 150 °C. This was much higher in comparison to that characteristic of a classical LiFePO₄ (solid) + 1 M LiPF₆ + 50 wt% EC + 50 wt% DMC system (T_f ≈ 37 °C).     

Mechanism transition of cell-impedance-controlled lithium transport through Li1−δMn2O4 composite electrode caused by surface-modification and temperature variation

The mechanism transition of lithium transport through a Li_1−δMn₂O₄ composite electrode caused by the surface-modification and temperature variation was investigated using the galvanostatic intermittent titration technique (GITT), electrochemical impedance spectroscopy (EIS) and the potentiostatic current transient technique. From the analyses of the ac-impedance spectra, experimentally measured from unmodified Li_1−δMn₂O₄ and surface-modified Li_1−δMn₂O₄ with MgO composite electrodes, the internal cell resistance of the MgO-modified Li_1−δMn₂O₄ electrode was determined to be much smaller in value than that of the unmodified electrode over the whole potential range. Moreover, from the analysis of the anodic current transients measured on the MgO-modified Li_1−δMn₂O₄ electrode, it was found that the cell-impedance-controlled constraint at the electrode surface is changed to a diffusion-controlled constraint, which is characterised by a large potential step and simultaneously by a small amount of lithium transferred during lithium transport. This strongly suggests that the internal cell resistance plays a significant role in determining the cell-impedance-controlled lithium transport through the MgO-modified Li_1−δMn₂O₄ electrode. Furthermore, from the temperature dependence of the internal cell resistance and diffusion resistance in the unmodified Li_1−δMn₂O₄ composite electrode measured by GITT and EIS, it was concluded that which mechanism of lithium transport will be operative strongly depends on the diffusion resistance as well as on the internal cell resistance.     

Effect of particle dispersion on high rate performance of nano-sized Li4Ti5O12 anode

Nano-sized Li₄Ti₅O₁₂ powders with high dispersivity were fabricated by a sol-gel process using P123 as surfactant, which exhibited much better high rate performance towards Li⁺ insertion/extraction as compared to the densely aggregated Li₄Ti₅O₁₂ particles although the primary grain sizes of both samples were almost the same. The Li₄Ti₅O₁₂ electrode prepared from the well-dispersed nanopowders can preserve 88.6% of the capacity at 0.1 A g⁻¹ when being cycled at 1 A g⁻¹, which is obviously higher than that of the densely aggregated sample, in which only 30% capacity can be retained. By improving the dispersivity, the specific surface area of the Li₄Ti₅O₁₂ nanoparticles, hence the electrode-electrolyte contact area was increased; meanwhile, more homogeneous mixing of the active materials with carbon black was achieved. All these factors might have resulted in the better high rate performance.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Synthesis of sawtooth-like Li4Ti5O12 nanosheets as anode materials for Li-ion batteries

Hierarchical layered hydrous lithium titanate and Li₄Ti₅O₁₂ microspheres assembled by nanosheets have been successfully synthesized via a hydrothermal process and subsequent thermal treatment. The electrochemical properties of the two samples have been investigated by galvanostatic methods. The former, with the obvious layered structure and a large surface area, delivers a reversible capacity of 180 mA h g⁻¹ after 200 cycles at 200 mA g⁻¹. As for Li₄Ti₅O₁₂, with the intriguing and unique sawtooth-like morphology, it presents exceptional high rate performance and excellent cycling stability. Up to 132 mA h g⁻¹ is obtained after 200 cycles at 10,000 mA g⁻¹ (57 C), proving itself promising for high-rate applications.     

An investigation of intercalation-induced stresses generated during lithium transport through sol-gel derived LixMn2O4 film electrode using a laser beam deflection method

The stress changes Δσ generated during lithium transport through the sol-gel derived Li_xMn₂O₄ film electrodes annealed at 773 and 873 K were quantitatively determined as a function of the lithium stoichiometry x using a laser beam deflection method (LBDM). Δσ generated during a real potential step between an initial electrode potential and a final applied potential was uniquely specified by the Δσ versus x curve. The Li_xMn₂O₄ film annealed at 773 K for 24 h (low temperature (LT)-Li_xMn₂O₄) showed larger capacity than the Li_xMn₂O₄ film annealed at 873 K for 6 h (high temperature (HT)-Li_xMn₂O₄) and this result is ascribed to the fact that the smaller the grain size is, the more increases the electrochemically active area of the film electrode. From the analysis of the normalised Δσ transient measured simultaneously along with the cyclic voltammogram in the potential range of 2.5-3.4 VLi/Li⁺, it is found that normalised Δσ generated in the LT-Li_xMn₂O₄ was smaller than that in the HT-Li_xMn₂O₄ during the lithium intercalation/de-intercalation around 3.0 VLi/Li⁺ region. This result gives an experimental evidence for the fact that the Jahn-Teller distortion is suppressed by the increase in the average oxidation state of manganese with decreasing in annealing temperature.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Carbon coated Li3V2(PO4)3 cathode material prepared by a PVA assisted sol-gel method

Carbon coated Li₃V₂(PO₄)₃ cathode material was prepared by a poly(vinyl alcohol) (PVA) assisted sol-gel method. PVA was used both as the gelating agent and the carbon source. XRD analysis showed that the material was well crystallized. The particle size of the material was ranged between 200 and 500 nm. HRTEM revealed that the material was covered by a uniform surface carbon layer with a thickness of 80 Å. The existence of surface carbon layer was further confirmed by Raman scattering. The electrochemical properties of the material were investigated by charge-discharge cycling, CV and EIS techniques. The material showed good cycling performance, which had a reversible discharge capacity of 100 mAh g⁻¹ when cycled at 1 C rate. The apparent Li⁺ diffusion coefficients of the material ranged between 9.5 × 10⁻¹⁰ and 0.9 × 10⁻¹⁰ cm² s⁻¹, which were larger than those of olivine LiFePO₄. The large lithium diffusion coefficient of Li₃V₂(PO₄)₃ has been attributed to its special NASICON-type structure.     

Improving the rate performance of LiFePO4 by Fe-site doping

LiFePO₄ doped by bivalent cation in Fe-sites show improved rate performance and cyclic stability. Under 10 C rate at room temperature, the capacities of LiFe_0.9M_0.1PO₄ (M = Ni, Co, Mg) maintain at 81.7, 90.4 and 88.7 mAh/g, respectively, in comparison with 53.7 mAh/g for undoped LiFePO₄ and 54.8 mAh/g for carbon-coated LiFePO₄ (LiFePO₄/C). The capacity retention is 95% after 100 cycles for doped samples while this value is only 70% for LiFePO₄ and LiFePO₄/C. Such a significant improvement in electrochemical performance should be partially related to the enhanced electronic conductivities (from 2.2 × 10⁻⁹ to <2.5 × 10⁻⁷ S cm⁻¹) and probably the mobility of Li⁺ ions in the doped samples.     

Electrochemical behavior of LiCoO2 in a saturated aqueous Li2SO4 solution

The electrochemical behavior of a commercial LiCoO₂ with spherical shape in a saturated Li₂SO₄ aqueous solution was investigated with cyclic voltammetry and electrochemical impedance spectroscopy. Three redox couples at E_SCE = 0.87/0.71, 0.95/0.90 and 1.06/1.01 V corresponding to those found at ELi/Li⁺=4.08/3.83, 4.13/4.03 and 4.21/4.14 V in organic electrolyte solutions were observed. The diffusion coefficient of lithium ions is 1.649 × 10⁻¹⁰ cm² s⁻¹, close to the value in organic electrolyte solutions. The results indicate that the intercalation and deintercalation behavior of lithium ions in the Li₂SO₄ solution is similar to that in the organic electrolyte solutions. However, due to the higher ionic conductivity of the aqueous solution, current response and reversibility of redox behavior in the aqueous solution are better than in the organic electrolyte solutions, suggesting that the aqueous solution is favorable for high rate capability. The charge transfer resistance, the exchange current and the capacitance of the double layer vary with the charge voltage during the deintercalation process. At the peak of the oxidation (0.87 V), the charge transfer resistance is the lowest. These fundamental results provide a good base for exploring new safe power sources for large scale energy storage.     

Preparation and characterization of ramsdellite Li2Ti3O7 as an anode material for asymmetric supercapacitors

Ramsdellite Li₂Ti₃O₇ was first synthesized via sol-gel process with good crystallity of an average particle size of 0.175 μm. The product was thoroughly investigated as a lithium intercalation compound, and as an active anode material in asymmetric supercapacitors coupling with activated carbon as cathode. Lithium intercalation reactions were found occurring at 1.32 and 1.62 V versus Li/Li⁺, respectively. A reversible specific capacity of 150 mA h g⁻¹ at 1C was obtained on Li₂Ti₃O₇ electrode in a nonaqueous electrolyte. The charge current was found to strongly influence the anodic discharge capacity in the asymmetric cell. The capacity retention at 10C charge-discharge rate was found to be 75.9% in comparison with that at 1C.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.     

Determination of lithium diffusion coefficient in LiFePO4 electrode by galvanostatic and potentiostatic intermittent titration techniques

A new model of lithium-ion transport processes in the LiFePO₄ electrode is proposed. This model takes into account the phase transition LiFePO₄ ↔ FePO₄ accompanying reversible lithium intercalation into the electrode during potential or current steps. The diffusion coefficient of Li⁺ ion and its dependence on the LiFePO₄/FePO₄ phase ratio have been determined by means of processing of experimental potential and current transients in accordance with the model's equations. The results of galvanostatic and potentiostatic intermittent titration techniques are in good agreement. The value of diffusion coefficient varies within 10⁻¹⁰-10⁻¹⁶ cm² s⁻¹ depending on the lithium content in solid solution Li_XFePO₄ and Li_1−XFePO₄ (X < 0.02) or the LiFePO₄/FePO₄ phase ratio.