Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

High-voltage performance of concentration-gradient Li[Ni0.67Co0.15Mn0.18]O2 cathode material for lithium-ion batteries

A novel Li[Ni_0.67Co_0.15Mn_0.18]O₂ cathode material encapsulated completely within a concentration-gradient shell was successfully synthesized via co-precipitation. The Li[Ni_0.67Co_0.15Mn_0.18]O₂ has a core of Li[Ni_0.8Co_0.15Mn_0.05]O₂ that is rich in Ni, a concentration-gradient shell having decreasing Ni concentration and increasing Mn concentration toward the particle surface, and a stable outer-layer of Li[Ni_0.57Co_0.15Mn_0.28]O₂. The electrochemical and thermal properties of the material were investigated and compared to those of the core Li[Ni_0.8Co_0.15Mn_0.05]O₂ material alone. The discharge capacity of the concentration-gradient Li[Ni_0.67Co_0.15Mn_0.18]O₂ electrode increased with increasing upper cutoff voltage to 4.5 V, and cells with this cathode material delivered a very high capacity, 213 mAh/g, with excellent cycling stability even at 55 °C. The enhanced thermal and lithium intercalation stability of the Li[Ni_0.67Co_0.15Mn_0.18]O₂ was attributed to the gradual increase in tetravalent Mn concentration and decrease in Ni concentration in the concentration-gradient shell layer.     

X-ray photoelectron spectroscopy and electrochemical behaviour of 4 V cathode, Li(Ni1/2Mn1/2)O2

Layered Li(Ni_1/2Mn_1/2)O₂ was prepared by the solution and mixed hydroxide methods, characterised by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and studied by cyclic voltammetry (CV) and charge discharge cycling in CC and CCCV modes at room temperature (r.t.) and at 50 °C. The XPS studies show about 8% of Ni³⁺ and Mn³⁺ ions are present in Li(Ni²⁺_1/2Mn_1/2⁴⁺)O₂ due to valency-degeneracy. The compound prepared at 950 °C, 12 h, solution method gives a second cycle discharge capacity of 150 mA h g⁻¹ (2.5-4.4 V) at a specific current of 30 mA g⁻¹ and retains 137 mA h g⁻¹ at the end of 40 cycles. CV shows that the redox process at 3.7-4.0 V corresponds to Ni²⁺↔Ni⁴⁺ and clear indication of Mn^3+/4+ couple was noted at 4.2-4.5 V. The observed capacity-fading (2.5-4.4 V) is shown to be contributed by the polarisation at the end of charging. The cathodic capacity is stable up to 40 cycles in the voltage window, 2.5-4.2 V both at room temperature and 50 °C.     

Lithium-deficient LiYMn2O4 spinels (0.9 ≤ Y < 1): Lithium content, synthesis temperature, thermal behaviour and electrochemical properties

Lithium-deficient Li_YMn₂O₄ spinels (LD-Li_YMn₂O₄) with nominal composition (0.9 ≤ Y < 1) have been synthesized by melt impregnation from Mn₂O₃ and LiNO₃ at temperatures ranging from 700 °C to 850 °C. X-ray diffraction data show that LD-Li_YMn₂O₄ spinels are obtained as single phases in the range Y = 0.975-1 at 700 °C and 750 °C. Morphological characterization by transmission electron microscopy shows that the particle size of LD-Li_YMn₂O₄ spinels increases on decreasing the Li-content. The influence of the Li-content and the synthesis temperature on the thermal and electrochemical behaviours has been systematically studied. Thermal analysis studies indicate that the temperature of the first thermal effect in the differential thermal analysis (DTA)/thermogravimetric (TG) curves, T_C1, linearly increases on decreasing the Li-content. The electrochemical properties of LD-Li_YMn₂O₄ spinels, determined by galvanostatic cycling, notably change with the synthesis conditions. So, the first discharge capacity, Q_disch., at C rate increases on rising the Li-content and the synthesis temperature. The sample Li_0.975Mn₂O₄ synthesized at 700 °C has a Q_disch. = 123 mAh g⁻¹ and a capacity retention of 99.77% per cycle. This LD-Li_YMn₂O₄ sample had the best electrochemical characteristics of the series.     

Fractal study of LiMn2O4 film electrode surface for lithium batteries application

Fractal structure of a LiMn₂O₄ film electrode has been investigated and its fractal dimensions was determined using different electrochemical techniques, viz. cyclic voltammetry and chronoamperometry. The results obtained from both these methods are in good agreement indicating the reliability of the estimated D_f. The fractal study of the LiMn₂O₄ film electrode suggests a complex surface with high fractal dimension. In addition, length scales of the electrode surface were also calculated.     

Porous Co3O4 nanoplatelets by self-supported formation as electrode material for lithium-ion batteries

In this paper, we have reported a simple and rapid approach for the large-scale synthesis of β-Co(OH)₂ nanoplatelets via the microwave hydrothermal process using potassium hydroxide as mineralizer at 140 °C for 3 h. Calcining the β-Co(OH)₂ nanoplatelets at 350 °C for 2 h, porous Co₃O₄ nanoplatelets with a 3D quasi-single-crystal framework were obtained. The process of converting the β-Co(OH)₂ nanoplatelets into the Co₃O₄ nanoplatelets is a self-supported topotactic transformation, which is easily controlled by varying the calcining temperature. The textural characteristics of Co₃O₄ products have strong positive effects on their electrochemical properties as electrode materials in lithium-ion batteries. The obtained porous Co₃O₄ nanoplatelets exhibit a low initial irreversible loss (18.1%), ultrahigh capacity, and excellent cyclability. For example, a reversible capacity of 900 mAh g⁻¹ can be maintained after 100 cycles.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Electrochemical properties of carbon-coated CaWO4 versus Li

Carbon-coated CaWO₄ nano-crystalline phases have been synthesized by ambient temperature solution precipitation method, characterized by X-ray diffraction, SEM and thermogravimetry and their electrochemical properties were studied versus Li metal. Galvanostatic cycling at a current of 60 mA/g in the voltage range 0.005-3.0 V on the 5 wt.% C-coated CaWO₄ gave a reversible capacity of 230 ± 5 mAh/g corresponding to 2.5 mol of Li, which is almost stable from 20 to 50 cycles. Under the same conditions, the 10 wt.% C-coated CaWO₄ showed a capacity of 355 ± 5 mAh/g (3.8 mol of Li) during the initial cycles, but the capacity degraded at a rate of 1.6 mAh/g per cycle in the range 5-100 cycles. A good operating voltage range was found to be 0.005-3.0 V with average discharge and charge potentials being 0.6 and 1.3 V, respectively. Coulombic efficiency in all cases was 96-98%. Cyclic voltammograms compliment the galvanostatic results. Impedance spectral data on the 10 wt.% C-coated CaWO₄ at different voltages during the first and 20th discharge-charge cycle have been interpreted in terms of the variations in the bulk and charge-transfer resistances of the composite electrode. A reaction mechanism involving the formation/decomposition of the oxide bronze, ‘Li_xWO_y’ has been proposed to explain the electrochemical cycling.     

Structural and electrochemical characteristics of Li4−xAlxTi5O12 as anode material for lithium-ion batteries

Al-doped Li₄Ti₅O₁₂ in the form of Li_4−xAl_xTi₅O₁₂ (x = 0, 0.05, 0.1 and 0.2) was synthesized via solid state reaction in an Ar-flowing atmosphere. Al-doping does not change the phase composition and particle morphology, but easily results in the lattice distortion and thus the poor crystallinity of Li₄Ti₅O₁₂. Al-doping decreases the specific capacity of Li₄Ti₅O₁₂, while improves remarkably its cycling stability at high charge/discharge rate. The substitution of Al for Li site can enhance the electronic conductivity of Li₄Ti₅O₁₂ via the generation of mixing Ti⁴⁺/Ti³⁺, whereas impede the Li-ion diffusion in the lattice. Excessive Al causes large electrode polarization due to the lower Li-ion conductivity, and thus leads to low specific capacity at high current densities. Li_3.9Al_0.1Ti₅O₁₂ exhibits a relatively high specific capacity and an excellent cycling stability.     

Low-temperature growth of well-crystalline Co3O4 hexagonal nanodisks as anode material for lithium-ion batteries

Uniform hexagonal-shaped cobalt oxide (Co₃O₄) nanodisks were prepared in large scale via facile aqueous solution based hydrothermal process at 110 °C. The detailed structural characterizations confirmed that the synthesized products are hexagonal cobalt oxide nanodisks, possessing very well-crystalline cubic spinel structure. A coin cell of type −2032 was assembled using the synthesized Co₃O₄ nanodisks and its charge–discharge profile was analyzed between the voltages 0.01 and to 2.5 V vs. Li/Li⁺ reference electrode. The electrochemical cell composed of Li/Co₃O₄ delivered an initial lithium insertion capacity of 2039 mAh/g. Although the cell exhibited high irreversible capacity during the first four cycles, the columbic efficiency has been improved upon cycling.     

Influence of manganese(II), cobalt(II), and nickel(II) additives in electrolyte on performance of graphite anode for lithium-ion batteries

Manganese dissolution into an electrolyte from the spinel LiMn₂O₄ in the lithium-ion cell has been recently investigated. In order to study the influence of the dissolved manganese species on the lithium intercalation/deintercalation into a natural graphite electrode, the electrochemical behavior of graphite was investigated in 1 mol dm⁻³ LiClO₄ electrolyte solution containing a small amount of Mn(II) by the addition of manganese(II) perchlorate. During the charging process, Mn(II) ions were firstly electroreduced on the electrode around 1.0 V versus Li/Li⁺ followed by irreversible decomposition of the electrolyte and lithium intercalation into the graphite. By microscopic observation of the graphite surface, manganese deposition was confirmed after the charge/discharge test. Due to the manganese deposition, the reversible capacity of the graphite electrode was drastically decreased. Furthermore, the cyclability of the anode was degraded with the amount of the manganese additive increasing. We compared these results with those of the cobalt(II) and nickel(II) additives by dissolving the corresponding perchlorates. Furthermore, we discussed the influence in practical cells based on the consideration of electrochemistry of the deposited metals.     

Enhanced cycling stability of LiMn2O4 cathode by amorphous FePO4 coating

The cycling performance of LiMn₂O₄ at room and elevated temperatures is improved by FePO₄ modification through chemical deposition method. The pristine and FePO₄-coated LiMn₂O₄ materials are characterized by X-ray diffraction, Raman spectroscopy, scanning electron microscopy and transmission electron microscopy. Their cycling performances are thoroughly investigated and compared. The 3 wt.% FePO₄-coated LiMn₂O₄ exhibits capacity losses of only 32% and 34% at room temperature and 55 °C, respectively, after 80 cycles, much better than those of the pristine material, 55% and 72%. The cyclic voltammograms at 55 °C reveal that the improvement in the cycling performance of FePO₄-coated LiMn₂O₄ electrodes can be attributed to the stabilization of spinel structures. The separation of FePO₄ between active materials and electrolyte and its interaction with SEI (solid electrolyte interphase) film are believed to account for the improved performances.     

Improved electrochemical properties of Li1+x(Ni0.3Co0.4Mn0.3)O2−δ (x = 0, 0.03 and 0.06) with lithium excess composition prepared by a spray drying method

Layered Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ (x = 0, 0.03 and 0.06) materials were synthesized through the different calcination times using the spray-dried precursor with the molar ratio of Li/Me = 1.25 (Me = transition metals). The physical and electrochemical properties of the lithium excess and the stoichiometric materials were examined using XRD, AAS, BET and galvanostatic electrochemical method. As results, the lithium excess Li_1.06(Ni_0.3Co_0.4Mn_0.3)O_2−δ could show better electrochemical properties, such as discharge capacity, capacity retention and C rate ability, than those of the stoichiometric Li_1.00(Ni_0.3Co_0.4Mn_0.3)O_2−δ. In this paper, the effect of excess lithium on the electrochemical properties of Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ materials will be discussed based on the experimental results of ex situ X-ray diffraction, transmission electron microscopy (TEM) and galvanostatic intermittent titration technique (GITT)     

Investigations into capacity fading as a result of a Jahn-Teller distortion in 4 V LiMn2O4 thin film electrodes

This study reports the onset of the Jahn-Teller distortion in 4 V LiMn₂O₄ thin film electrodes that was investigated using an in situ bending beam method (BBM). The phase transformation during lithium insertion/extraction could be detected using the BBM technique. The phase transformation between the cubic and tetragonal phases was depicted by the larger value of the compressive or tensile differential strain, which is consistent with a well-known phase transformation between those phases in 3 V LiMn₂O₄. The cyclic deflectograms and cyclic voltammograms were obtained simultaneously. The potential ranges responsible for the Jahn-Teller distortion in 4 V range, which takes place at the electrode surface, was determined by the charge versus. differential strain (dε/dQ) curve. The onset of the Jahn-Teller distortion was observed at the end of the cathodic scan, and the relaxation of the Jahn-Teller distortion was observed at the beginning of anodic scan. Furthermore, the onset of the Jahn-Teller distortion was found to be dependent on the lithium ion insertion rate, which was controlled by the scan rate.     

A comparative electrochemical study of LiMn2O4 spinel thin-film and porous laminate

Novel Electrostatic Spray Deposition (ESD) technique was used to fabricate LiMn₂O₄ spinel thin-films. Cyclic voltammograms of both the ESD and porous laminate films show the double peaks in the 4.0 V range characteristic of the LiMn₂O₄ spinel materials. The porous laminates exhibit two semicircles in the impedance spectra while the ESD films show only one single semicircle. The diffusion time constant in the laminate films was typically one order of magnitude larger than that in the ESD thin-films. The apparent lithium-ion chemical diffusion coefficient in LiMn₂O₄ was found to be of the order of 10⁻⁹ cm²/s for both the porous laminate film and the ESD films despite the difference in the diffusion time constants.     

Comparative study of Li(Li1/3Ti5/3)O4 and Li(Ni1/2−xLi2x/3Tix/3)Ti3/2O4 (x = 1/3) anodes for Li rechargeable batteries

A solid solution of spinel (2/3)Li(Li_1/3Ti_5/3)O₄–(1/3)Li(Ni_1/2Ti_3/2)O₄ was prepared, and its structural/electrochemical properties were compared with Li(Li_1/3Ti_5/3)O₄ to identify the effect of doping to the structural invariance of Li(Li_1/3Ti_5/3)O₄. The solid solution retained the zero strain characteristic of Li(Li_1/3Ti_5/3)O₄ during discharge/charge with an excellent cycle stability, while the rate capability was notably improved. However, a reversible broadening of the XRD peak was observed at the end of discharge, indicating some structural changes. XANES measurements showed that the oxidation state of Ti was +4 and that of Ni was +2 in the solid solution.     

Electrochemical properties of La1−xSrxFeO3 (x = 0.2, 0.4) as negative electrode of Ni-MH batteries

La_(1−x)Sr_xFeO₃ (x = 0.2,0.4) powders were prepared by a stearic acid combustion method, and their phase structure and electrochemical properties were investigated systematically. X-ray diffraction (XRD) analysis shows that La_(1−x)Sr_xFeO₃ perovskite-type oxides consist of single-phase orthorhombic structure (x = 0.2) and rhombohedral one (x = 0.4), respectively. The electrochemical test shows that the reaction at La_(1−x)Sr_xFeO₃ oxide electrodes are reversible. The discharge capacities of La_(1−x)Sr_xFeO₃ oxide electrodes increase as the temperature rises. With the increase of the temperature from 298 K to 333 K, their initial discharge capacity mounts up from 324.4 mA h g⁻¹ to 543.0 mA h g⁻¹ (when x = 0.2) and from 147.0 mA h g⁻¹ to 501.5 mA h g⁻¹ (when x = 0.4) at the current density of 31.25 mA g⁻¹, respectively. After 20 charge-discharge cycles, they still remain perovskite-type structure. Being similar to the relationship between the discharge capacity and the temperature, the electrochemical kinetic analysis indicates that the exchange current density and proton diffusion coefficient of La_(1−x)Sr_xFeO₃ oxide electrodes increase with the increase of the temperature. Compared with La_0.8Sr_0.2FeO₃, La_0.6Sr_0.4FeO₃ electrode is a more promising candidate for electrochemical hydrogen storage because of its higher cycle capacity at various temperatures.     

Preparation and electrochemical properties of LiMn2O4 by the microwave-assisted rheological phase method

Pure-phase and well-crystallized spinel LiMn₂O₄ powders as cathode materials for lithium-ion batteries were successfully synthesized by a new simple microwave-assisted rheological phase method, which was a timesaving and efficient method. The physical properties of the as-synthesized samples compared with the pristine LiMn₂O₄ obtained from the rheological phase method were investigated by thermogravimetry analysis (TGA), X-ray diffraction (XRD) and scanning electronic microscope (SEM). The as-prepared powders were used as positive materials for lithium-ion battery, whose charge/discharge properties and cycle performance were examined in detail. The powders resulting from the microwave-assisted rheological phase method were pure, spinel structure LiMn₂O₄ particles of regular shapes with distribution uniformly, and exhibited promising electrochemical properties for battery. Furthermore, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were employed to characterize the reactions of Li-ion insertion into and extraction from LiMn₂O₄ electrode.     

Hydrothermal synthesis of Li(Ni1/3Co1/3Mn1/3)O2 for lithium rechargeable batteries

Ultrafine powders of Li(Ni_1/3Co_1/3Mn_1/3)O₂ cathode materials for lithium-ion secondary batteries were prepared under mild hydrothermal conditions. The influence of the molar ratio of Li/(Ni + Co + Mn) was studied. The products were investigated by XRD, TEM and EDS. The final products were found to be well crystallized Li(Ni_1/3Co_1/3Mn_1/3)O₂ with an average particle size of about 10 nm.