纤维光学

光纤及其传输理论TN252007021488在DCF光纤中放大的背向自发喇曼散射的增益特性=Gain character of amplified backward spontaneous Ramanscattering in DCFfiber[刊,中]/徐海峰(上海理工大学光学与电子信息工程学院.上海(200093)),张在宣…//光电工程.-2006,33(11).-97-100光脉冲沿色散补偿光纤(DCF)传输会产生背向自发喇曼散射,当入纤激光功率大于阈值时,出现放大的背向自发喇曼散射现象。实验发现,反斯托克斯(ASR)和斯托克斯(SR)自身脉冲光纤喇曼放大的阈值泵浦峰值脉冲功率是18.2W和14.5W。当入纤激光功率为52W时,背向SR和AS…     

基于时分复用和窄波长扫描激光的长距离光纤布喇格光栅传感系统

提出了一种通过提高长距离光纤布喇格光栅传感系统容量,从而实现多传感点参量测量的新方法.采用时分复用、窄波长范围扫描激光方式,将多个中心波长相近的低反射率光纤布喇格光栅放置于系统的不同位置,构成准分布式光纤传感系统,实现了多个传感点参量的同时测量.同时提出了采用掺铒光纤和喇曼混合放大方法来延长传感距离.在系统的中间加入一个喇曼泵浦进行喇曼放大以此补偿光纤布喇格光栅反射的信号,系统末端的掺铒光纤利用前面喇曼泵浦剩余的泵浦功率产生自发辐射光并放大传感信号,使得整个系统的传感距离延长.实验证实:将三只中心波长均在1580nm附近,反射率均小于4%的光纤布喇格光栅,分别放置在系统的不同位置,在200km处获得了15dB的信噪比,反射信号明显;并且在200km处的静态应变和温度实验中,线性度均达到了0.999以上.     

基于时分复用和窄波长扫描激光的长距离光纤布喇格光栅传感系统

提出了一种通过提高长距离光纤布喇格光栅传感系统容量,从而实现多传感点参量测量的新方法.采用时分复用、窄波长范围扫描激光方式,将多个中心波长相近的低反射率光纤布喇格光栅放置于系统的不同位置,构成准分布式光纤传感系统,实现了多个传感点参量的同时测量.同时提出了采用掺铒光纤和喇曼混合放大方法来延长传感距离.在系统的中间加入一个喇曼泵浦进行喇曼放大以此补偿光纤布喇格光栅反射的信号,系统末端的掺铒光纤利用前面喇曼泵浦剩余的泵浦功率产生自发辐射光并放大传感信号,使得整个系统的传感距离延长.实验证实：将三只中心波长均在1 580 nm附近,反射率均小于4%的光纤布喇格光栅,分别放置在系统的不同位置,在200 km处获得了15 dB的信噪比,反射信号明显|并且在200 km处的静态应变和温度实验中,线性度均达到了0.999以上.     

基于喇曼/掺铒光纤混合放大的长距离布喇格光栅传感器系统

提出了一种提高长距离光纤布喇格光栅信噪比以进行准分布测量的新方法.本方法基于双向喇曼放大和双掺铒光纤结构,喇曼光纤放大器对布喇格光栅信号进行低噪音的双向放大,置于远处的掺铒光纤利用剩余的泵浦功率产生自发辐射光和放大传感信号,为第二段掺铒光纤之后的远处布喇格光栅传感器提供光以及补偿由于长距离传输造成的光纤损耗.实验显示传感器系统的性能得到显著提高.使用功率为240 mW的单个普通泵浦,分布在50 km光纤上的FBG均可获得15 dB的良好信噪比,比混合放大前提高了10 dB.     

多泵浦光纤喇曼放大器的模拟分析

通过使用综合理论模型对不同配置条件下的多泵浦分布式光纤喇曼放大器的增益谱进行了数值模拟研究,该理论模型包含了瑞利散射、放大自发辐射和不同交互效应,包括泵浦与泵浦、泵浦与信号和信号与信号之间的交互与能量转移.模拟研究了泵浦源功率、泵浦源波长间隔及光纤损耗对喇曼增益谱的影响,结果表明设计多泵浦光纤喇曼放大器需要对泵浦源功率、泵浦源波长间隔光纤损耗谱进行综合考虑,需对泵浦源功率、泵浦源波长间隔进行合理配置.在本文的泵浦源波长设定条件下,考虑实际光纤的损耗谱特性,为了获得大的增益带宽和小的增益不平坦度,短波长泵浦源和最长波长的泵浦源需要更高的泵浦功率,中间波长泵浦源的功率应较低.     

双向反馈布里渊-喇曼光纤激光器输出特性

设计了一种双向反馈布里渊-喇曼光纤激光器,研究了布里渊泵浦对输出特性的影响.布里渊-喇曼光纤激光器由一段7km色散补偿光纤、1 455nm喇曼泵浦、可调谐激光器及双反馈环组成.喇曼泵浦功率固定在250mW,布里渊泵浦工作波段在喇曼峰值增益处附近,可得到较多波长数输出.随着布里渊泵浦功率增加,相邻的布里渊斯托克斯光和经背向瑞利散射的斯托克斯光之间功率差减小,同时各阶斯托克斯光平均强度增加并达到饱和.受色散补偿光纤中喇曼交叉增益影响,布里渊泵浦功率由1.8dBm增加到6.9dBm,输出多波长数先增后减.当布里渊泵浦功率为4.4dBm时,对应输出波长数最多,为37个,波长间隔0.078nm.     

基于掺铒光纤/喇曼混合放大的光纤激光器布喇格光栅传感系统

提出了一种提高长距离光纤布喇格光栅信噪比以进行准分布测量的新方法.该方法基于掺铒光纤/喇曼混合放大的光纤激光器结构,掺铒光纤和滤波器构成的环形结构产生激光作为光源,喇曼光纤放大器对布喇格光栅信号进行低噪音的双向放大,置于远处的掺铒光纤利用剩余的泵浦功率产生自发辐射光和放大传感信号,为远处掺铒光纤之后的布喇格光栅传感器提供信号光以及补偿由于长距离传输造成的光纤损耗.实验显示,与使用宽带光源的传感方式相比,系统的性能得到显著提高,仅使用小功率泵浦,分布在50 km光纤上的FBG均获得了超过58 dB的优良信噪比.     

硅波导受激喇曼散射放大信号光的数值模拟

提出了用连续泵浦光在硅波导中的受激喇曼散射对信号光进行放大的方法.建立了信号光和泵浦光在硅波导中传输的耦合方程,得到了计算信号光增益的理论模型.利用数值模拟结果,对泵浦功率沿波导的分布,信号光在不同波导长度以及输入功率情况下的增益等进行了分析和讨论.结果表明,适当增加波导长度和泵浦光功率可以得到较高喇曼增益的结论.     

单模石英光纤中受激喇曼散射的研究

利用连续光纤激光器为泵浦源,对单模石英光纤中的受激喇曼散射进行了实验研究.在较低功率泵浦下,观察到由自发喇曼散射向受激喇曼散射演化的过程中,光谱不断变窄;当Stokes波信号功率较强时,观察到光谱峰值相对于泵浦波的频移量从440 cm－1转化到490 cm－1.在改进耦合系统后,不仅观察到一级喇曼频移,并且观察到了高阶Stokes光.在产生多级喇曼光谱时能量移动比较复杂,每两级的喇曼频移间隔并不完全相同.     

级联掺磷光纤喇曼激光器的解析优化

讨论了二级级联喇曼光纤激光器的解析解和优化设计.通过引入几何平均功率、增益因子和归一化光纤有效长度,将描述泵浦光和斯托克斯光沿喇曼增益光纤分布的微分方程组简化成代数方程组,在对泵浦光采用线性传播近似后,获得了二级级联喇曼激光器的解析解.所获得的解析解同数值模拟结果吻合得很好.利用该解析解可方便和快速地讨论级联喇曼激光器的优化设计,计算不同泵浦功率下的最佳光纤长度、输出光纤光栅反射率和转换效率.泵谱功率越大,最佳光纤长度越短,最佳输出光纤光栅反射率越小.     

Low pump power co-fiber remotely pumped EDFA used in DWDM systems with ultra-long fiber span

In this paper, aiming at practical dense wavelength division multiplexing (DWDM) system with ultralong fiber span, a simple co-fiber remotely pumped erbium-doped fiber amplifier (RP-EDFA) scheme is proposed to extend span distance with simple configuration and low pump power. Equivalent noise figure of -6 dB is achieved under 300-mW pump power. Using the experiment results, numerical simulation of ultra-long span systems shows that for a 40 × 11.6-Gb/s transmission system, the RP-EDFA scheme can support transmission of 1760 km with a fiber span of 160 km. These results demonstrate the potential of the PR-EDFA scheme in ultra-long span transmission.     

Fibre raman amplifier properties for applications to long-distance optical communications

This paper reviews recent theoretical and experimental studies on optical amplification by stimulated Raman scattering (Raman amplification) in single-mode optical fibres, and discusses its possible applications to long-distance optical communications. The fibre Raman amplifier can be used as an in-line optical amplifier in both repeaterless and non-regenerative all-optical repeater configurations. In the former application, signal transmission of over 400 km has been predicted theoretically, although high-power pump sources are considered to be required. In the latter configuration, in which optical fibre losses are compensated for by Raman gains, it has been shown that extremely long-distance transmission over more than 1000 km is feasible in terms of signal-to-noise ratio, where the distance achievable is mainly limited by the accumulation of Raman noise. Recent experimental demonstrations including bit-error rate measurements on the Raman amplified signal, and laser-diode pumped amplification, etc., are also reviewed. The results confirm the effectiveness of fibre Raman amplifiers in future long-haul systems.     

基于拉曼组合放大的长距离光纤传输系统

本文改进了一种实现长距离自适应补偿光纤传输的方法.在利用光纤光栅形成的谐振腔产生激光对信号光进行拉曼放大的基础上,再利用双抽运光对信号光进行拉曼放大,从而获得更高的拉曼增益以实现更长距离的自适应补偿光纤传输.使实验自适应补偿传输距离达125km(为目前国际上已报道的最长自适应补偿光纤传输距离).实验测量并理论分析了该长距离光纤传输系统的开关增益、放大的自发辐射噪声、噪声指数和光功率分布的特性,实验结果与理论模型符合很好.     

基于光纤环形激光器和光放大的100 km光纤布拉格光栅传感系统

在基于掺铒光纤-拉曼混合放大的可调光纤环形激光器的光纤布拉格光栅(FBG)传感系统结构基础上,提出了延长传感距离的新方法。该方法以环形掺铒光纤激光器作为光源,采用双波长拉曼放大的方法对信号进行低噪声的双向放大,系统中间的两段掺铒光纤再利用剩余的抽运功率产生自发辐射光和放大传感信号,使得整个系统能够在超长的传感距离上获得很高的信噪比。实验表明使用一只40 mW的掺铒光纤放大(EDFA)抽运源、一只170 mW的拉曼抽运源和一只2 W的拉曼抽运源,可以使整个系统的传感距离达到100km,并且传感系统的光纤布拉格光栅反射信号均能获得超过57 dB的优良信噪比,从而实现在超长距离上的光纤布拉格光栅传感。     

Long-distance fiber Bragg grating sensor system with a high optical signal-to-noise ratio based on a tunable fiber ring laser configuration

A novel tunable fiber ring laser configuration with a combination of bidirectional Raman amplification and dual erbium-doped fiber (EDF) amplification is proposed for realizing high optical signal-to-noise ratio (SNR), long-distance, quasi-distributed fiber Bragg grating (FBG) sensing systems with large capacities and low cost. The hybrid Raman-EDF amplification configuration arranged in the ring laser can enhance the optical SNR of FBG sensor signals significantly owing to the good combination of the high gain of the erbium-doped fiber amplifier (EDFA) and the low noise of the Raman amplification. Such a sensing system can support a large number of FBG sensors because of the use of a tunable fiber Fabry-Perot filter located within the ring laser and spatial division multiplexing for expansion of sensor channels. Experimental results show that an excellent optical SNR of approximately 60 dB has been achieved for a 50 km transmission distance with a low Raman pump power of approximately 170 mW at a wavelength of 1455 nm and a low EDFA pump power of approximately 40 mW at a wavelength of 980 nm, which is the highest optical SNR achieved so far for a 50 km long FBG sensor system, to our knowledge.     

Optimal Configuration of Multiple Pump Powers and Wavelengths for Balanced Pre- and Post-pumped Raman Fiber Amplifiers

A novel configuration algorithm for bi-directionally pumped Raman amplifier is developed by adopting simulated annealing algorithm. Automatic design of optical fiber Raman amplifier using 10 laser diode pumps with different wavelengths and powers is demonstrated for 64 channels DWDM systems. The resulted gain ripple is less than 2.6 dB in amplification bandwidth of more than 50 nm for a transmission span of more than 300 km. The algorithm can be practically applied to desired signal channel number and gain profile.     

Optimal Configuration of Multiple Pump Powers and Wavelengths for Balanced Pre- and Post-pumped Raman Fiber Amplifiers

A novel configuration algorithm for bi-directionally pumped Raman amplifier is developed by adopting simulated annealing algorithm. Automatic design of optical fiber Raman amplifier using 10 laser diode pumps with different wavelengths and powers is demonstrated for 64 channels DWDM systems. The resulted gain ripple is less than 2.6 dB in amplification bandwidth of more than 50 nm for a transmission span of more than 300 km. The algorithm can be practically applied to desired signal channel number and gain profile.     

Controllable optical response in hybrid opto-electromechanical systems

We theoretically investigate the analog of electromagnetically induced absorption and parametric amplification in a hybrid opto-electromechanical system consisting of an optical cavity and a microwave cavity coupled to a common mechanical resonator. When the two cavity modes are driven by two pump fields, a weak probe beam is applied to the optical cavity to monitor the optical response of the hybrid system, which can be effectively controlled by adjusting the frequency and power of the two pump fields. We find that the analog of electromagnetically induced absorption and parametric amplification can appear in the probe transmission spectrum when one cavity is pumped on its red sideband and another is pumped on its blue sideband. These phenomena can find potential applications in optical switching and signal amplification in the quantum information process.