Bi/TiO2复合纳米纤维制备及可见光催化性能

以电纺TiO₂纳米纤维为基质,EDTA为鳌合剂和吸附剂,采用溶剂热法制备Bi/TiO₂复合纳米纤维光催化材料,利用X射线粉末衍射（XRD）、扫描电镜（SEM）、X射线能量色散谱（EDS）、透射电镜（TEM）、紫外-可见漫反射光谱（UV-Vis DRS）和荧光光谱（PL）等分析测试手段对样品的物相、形貌和光学性能等进行表征,以罗丹明B（RhB）为模拟有机污染物,考察了样品的光催化性能。结果表明：EDTA在复合纳米纤维的合成过程中起到关键作用,通过改变EDTA的用量可以有效控制纤维表面构筑单质Bi纳米球的大小和覆盖密度。所制备的复合纳米纤维具有良好的可见光催化活性和稳定性,当单质Bi的负载量为65%时光催化活性最强,可见光照射180 min,RhB的降解率达到96.40%,循环使用5次降解率仍保持在91%以上。     

Ce掺杂Bi2MoO6/TiO2纳米纤维异质结的制备及可见光催化性能

以静电纺丝技术制备的TiO_2纳米纤维为基质,通过溶剂热法制备了异质结型稀土Ce掺杂Bi_2MoO_6/TiO_2复合纳米纤维。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)以及荧光光谱(PL)等分析测试手段对样品的物相、形貌和光学性能等进行表征。以罗丹明B为模拟有机污染物,研究了样品的可见光催化性能。结果表明:在稀土掺杂样品中,Ce离子进入Bi_2MoO_6晶格,部分取代Bi3+,导致晶胞膨胀,晶格畸变,形成缺陷;与TiO_2复合形成异质结,有利于光生电荷的产生、转移和有效分离,从而提高TiO_2纳米纤维的光催化活性。可见光照射180 min,罗丹明B的降解率达到95.1%。经5次循环光催化降解活性基本不变,样品具有良好的光催化稳定性。     

Pr掺杂Bi_2MoO_6/TiO_2复合纳米纤维的制备及可见光催化性能

以电纺TiO_2纳米纤维为基质,采用溶剂热法制备了稀土Pr掺杂Bi_2MoO_6/TiO_2复合纳米纤维,利用X射线衍射仪、扫描电子显微镜、透射电子显微镜、紫外-可见-近红外分光光度计和荧光光谱仪等对不同样品的物相、形貌和光学性能等进行表征,以甲基橙为模拟有机污染物,考察了样品的光催化性能.结果表明,在复合样品中,Pr~(3+)进入Bi_2MoO_6晶格,部分取代Bi~(3+)形成施主能级,导致能级带隙变窄,不仅有利于提高样品的可见光催化活性,抑制光生电子-空穴对复合,而且还提高了Bi_2MoO_6/TiO_2的光催化活性和稳定性.当Pr的掺杂量为3%(摩尔分数)时,光催化降解甲基橙的效果最佳,可见光照射180 min时降解率达到93.8%,比纯Bi_2MoO_6/TiO_2的降解率有明显提高.     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

Bi_(20)TiO_(32)/聚丙烯腈复合纳米纤维的制备及其对异丙隆的光催化降解性能

采用溶剂热法制备了可见光响应型光催化剂Bi_(20)TiO_(32),为了实现该光催化剂的固定化负载,进一步以Bi_(20)TiO_(32)和聚丙烯腈(PAN)为原料,通过同轴静电纺丝法制备了不同光催化剂含量的Bi_(20)TiO_(32)/PAN复合纳米纤维。通过这一途径一方面可以便于光催化剂的回收利用,另一方面纳米纤维结构可以提高光催化剂与有机污染物反应的接触面积。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和氮气吸附-脱附法对样品的物相组成、形貌结构、光谱吸收和比表面积等进行表征。研究了在可见光照射下Bi_(20)TiO_(32)/PAN复合纳米纤维膜对苯脲类农药异丙隆的光催化降解性能。结果显示,制备的Bi_(20)TiO_(32)光催化剂禁带宽度为2.35 eV,属于典型的可见光响应型光催化剂。制备的Bi_(20)TiO_(32)/PAN复合纳米纤维直径在600~700 nm,Bi_(20)TiO_(32)可以在纳米纤维表面均匀负载,复合纳米纤维膜对可见光具有明显的响应性,对异丙隆具有很好的光催化降解效果,其中光催化剂质量分数为25.7%的样品S3对异丙隆的降解率最高可达到87%。这一研究表明,通过同轴静电纺丝法将光催化剂负载于有机纳米纤维表面,可以保持光催化剂原有光催化效果,是实现光催化剂固定化一条较好的途径。     

添加NaBF_4对阳极氧化法制备TiO_2纳米管光催化剂的影响

在阳极氧化电解液中添加Na BF4制得了具可见光活性的B掺杂TiO_2纳米管阵列(B/TNTs)。采用扫描电镜(FE-SEM)、能谱仪(EDS)、X射线衍射(XRD)、傅立叶红外光谱(FTIR)、紫外-可见漫反射光谱(UV-Vis DRS)以及X射线光电子能谱(XPS)对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明:添加Na BF4后,TiO_2纳米管表面形貌变化较大;B掺入到TiO_2晶格中形成B-O-Ti键;B掺杂使得TiO_2纳米管表面羟基量增加、光学带隙能减小、光吸收阀值红移,且B掺杂量越多,其相应值的变化量越大;B掺杂能促进TiO_2锐钛矿相的发育,纳米管经550℃煅烧后仍保持未掺杂样品的锐钛矿相结构;Na BF4的最佳添加量为0.6%(w/w)时,所得样品光催化活性最佳,可见光下光催化降解MB的4 h降解率由未添加的39.90%提高至75.15%,且反复使用10次后其光催化性能基本保持不变;总有机碳(TOC)分析结果表明,MB在可见光下能被B/TiO_2有效矿化。     

水热法合成LaPO_4/TiO_2异质结复合光催化材料及性能研究

以静电纺丝技术制备的锐钛矿相TiO_2纳米纤维为基质,尿素为碱源,环己烷六羧酸为小分子模板剂,采用水热法合成了LaPO_4/TiO_2异质结复合纳米纤维。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高倍透射电子显微镜(HRTEM)和X射线衍射(XRD)等分析测试手段对产物形貌和结构进行了表征,并以甲基橙为模拟污染物,紫外光为光源,评价了样品光催化降解活性。结果表明:LaPO_4纳米棒均匀地构筑在TiO_2纳米纤维表面,制备了LaPO_4/TiO_2异质结复合纳米纤维光催化材料,其具有比纯TiO_2纳米纤维和Degussa P-25更强的光催化活性,降解率达到89.4%。     

异质结型La_2Ti_2O_7/TiO_2复合纳米纤维的制备及光催化降解

以静电纺丝技术制备的TiO_2纳米纤维为模板和反应物,采用水热法合成了具有异质结构的La_2Ti_2O_7/TiO_2复合纳米纤维。将其作为光催化剂,在紫外光和可见光环境中,对模拟有机污染物罗丹明B进行光催化降解。采用XRD,SEM和HRTEM等分析测试手段对样品的组成及形貌进行表征,通过UV-vis漫反射光谱表征其光吸收性能及禁带宽度,测试光催化性能。结果表明:TiO_2纳米纤维形貌得以完好保持,La_2Ti_2O_7纳米晶粒均匀地生长在TiO_2纳米纤维表面形成异质结,减小了TiO_2的带隙宽度,光催化活性提高,光谱响应范围拓宽到可见光区。在紫外光和可见光下均具有良好的光催化活性。     

Au与Fe_3O_4纳米微粒共嵌TiO_2纳米纤维的制备及可见光催化性能

通过静电纺丝法制备出含有Fe3O4纳米微粒的TiO2纳米纤维,再采用浸渍还原法将Au纳米微粒嵌入到TiO2纳米纤维上,制备出一种具有较强磁性和良好可见光响应能力的复合光催化材料.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见固体漫反射光谱仪(UV-VisDRS)等对样品的结构和形貌进行表征,并以降解罗丹明B(RhB)为模型反应,考察了样品在可见光照射下的光催化性能.结果表明,嵌入Au纳米微粒可使复合纳米纤维在可见光下降解RhB时表现出非常好的降解速率和降解率;同时,将Fe3O4纳米微粒嵌入TiO2纳米纤维内部可以赋予材料较强的磁性,使材料便于分离和重复利用.     

pH值对Bi_2MoO_6晶体形貌和可见光催化性能的影响

以(NH4)6Mo7O24·4H2O和Bi(NO3)3·5H2O为原料,采用普通水热法制备Bi2Mo O6光催化剂,研究p H值对制备该光催化剂的影响。对所制备的系列样品,采用X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、比表面积分析仪、X射线光电子能谱仪(XPS)和紫外-可见漫反射(UV-Vis DRS)进行表征。结果表明:p H值对Bi2Mo O6晶体的物相组成、形貌和光催化性能均有显著影响。p H值为1~7时,所制备的样品为纯相Bi2Mo O6,p H值为9或11时,出现第二相Bi3.64Mo0.36O6.55;随着p H值的升高,形貌依次为纳米棒、纳米片和无规则纳米颗粒。在可见光(λ≥420 nm)照射下,通过光催化降解罗丹明B(Rhodamine B,Rh B),探讨了制备Bi2Mo O6的p H值对其可见光催化活性的影响。当p H=7时,制备的样品光催化效果最好,光照50 min后对初始浓度为5 mg·L-1的罗丹明B溶液的降解率为85%。     

Bi@Bi2Sn2O7/TiO2等离子体复合纤维的制备及增强的光催化产氢活性

以电纺TiO_2纳米纤维为基质,采用一步水热法合成了Bi@Bi_2Sn_2O_7/TiO_2等离子体复合纤维光催化剂。利用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、高分辨透射电镜(HRTEM)、紫外-可见漫反射(UV-Vis DRS)和光致发光光谱(PL)等分析测试手段对样品的物相、形貌和光电性能等进行表征。以三乙醇胺为电子给体,研究了Bi@Bi_2Sn_2O_7/TiO_2复合纤维光催化裂解水制氢的反应过程。结果表明:在水热过程中,Bi_2Sn_2O_7构筑在TiO_2纳米纤维表面形成p-n结的同时,部分Bi3+被葡萄糖还原成金属Bi沉积在Bi_2Sn_2O_7上。金属Bi的等离子体共振效应与p-n结的协同作用,有效提高了样品的光催化活性,产氢速率达到7.26 mmol·h~(-1)·g~(-1)。     

A Simple Method for the Preparation of TiO2/Ag‐AgCl@Polypyrrole Composite and Its Enhanced Visible‐Light Photocatalytic Activity

A novel and facile method was developed to prepare a visible‐light driven TiO₂/Ag‐AgCl@polypyrrole (PPy) photocatalyst with Ag‐AgCl nanoparticles supported on TiO₂ nanofibers and covered by a thin PPy shell. During the synthesis, the PPy shell and Ag‐AgCl nanoparticles were prepared simultaneously onto TiO₂ nanofibers, which simplified the preparation procedure. In addition, because Ag‐AgCl aggregates were fabricated via partly etching the Ag nanoparticles, their size was well controlled at the nanoscale, which was beneficial for improvement of the contact surface area. Compared with reference photocatalysts, the TiO₂/Ag‐AgCl@PPy composite exhibited an enhanced photodegradation activity towards rhodamine B under visible‐light irradiation. The superior photocatalytic property originated from synergistic effects between TiO₂ nanofibers, Ag‐AgCl nanoparticles and the PPy shell. Furthermore, the TiO₂/Ag‐AgCl@PPy composite could be easily separated and recycled without obvious reduction in activity.     

Gd-N共掺杂SrTiO3/TiO2复合纳米纤维制备及光催化性能

以静电纺丝技术制备的TiO_2纳米纤维为基质和反应物,结合一步水热法制得Gd-N共掺杂SrTiO_3/TiO_2复合纳米纤维光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、高分辨透射电镜(HRTEM)、X射线光电子能谱(XPS)、紫外-可见漫反射(UV-Vis DRS)和荧光光谱(PL)等方法对其微观结构、形貌和光学性能进行表征。结果表明:SrTiO_3和TiO_2形成异质结能够使光生电子和空穴得到很好的分离,而Gd-N共掺杂产生新带隙,可以拓宽光谱响应范围至可见光区,并引起晶格缺陷,成为光生电子-空穴对的浅势捕获阱。Gd-N共掺杂与异质结的协同作用有效提高了SrTiO_3/TiO_2复合纳米纤维的可见光催化活性。     

Fabrication and photocatalytic property of TiO<Subscript>2</Subscript> nanofibers

TiO₂ nanofibers were prepared from tetrabutyl titanate sol precursors by using electrospun method. X-ray diffraction (XRD) and atomic force microscope (AFM) were used to characterize their crystal structure and morphology feature. The results demonstrated that TiO₂ nanofibers possessed anatase phase and the average diameter of TiO₂ nanofibers was about 150 nm. The photocatalytic property of TiO₂ nanofibers was evaluated for the photodecomposition of methyl orange solution. And TiO₂ nanofibers exhibited high photocatalytic activities with transfer efficiency about 100% after 20 min.     

Application of the Composite of TiO2 Nanoparticles and Carbon Nanotubes to the Photo-Reduction of Cr(VI) in Water

The composite of carboxyl-modified multi-walled carbon nanotubes (MWNT-COOH) and TiO₂ nanoparticles was prepared in a solvothermal process. The x-ray diffraction (XRD), transmission electron microscope (TEM) and UV-vis spectrum were used to characterize the products. The results showed that the MWNT-COOH was dispersed uniformly in the composite and coated with TiO₂ nanoparticles. The photo-reduction of Cr(VI) to Cr(III) in water catalyzed by the composite was investigated at room temperature. The photocatalytic activity of the composite markedly increased by a factor of approximately 2.2 in comparison with pure TiO₂ (P25). Furthermore, the mechanism of the photocatalytic activity enhancement of the MWNT-COOH/TiO₂ nanoparticles composite for the photo-reduction of Cr(VI) was discussed.     

Synthesis,Adsorptive, and Photocatalytic Properties of Carbon Nanotubes/TiO<Subscript>2</Subscript> Nanocomposite Photocatalysts

The carbon nanotubes/TiO₂ (CNTs/TiO₂) composite photocatalysts composed of TiO₂ nanoparticles and multiwalled carbon nanotubes (CNTs) were prepared by a facile hydrothermal method. The photocatalysts were characterized by a range of analytical techniques including X-ray powder diffraction, field emission scanning electron microscope, thermal gravimetric analysis and UV–Vis optical absorption spectra, etc. The amount of TiO₂ nanoparticles growing on CNTs could be tuned by adjusting the dosage of precursor in the reaction solution. Both the adsorptivity and photocatalytic activities of pure CNTs, pure TiO₂, and the CNTs/TiO₂ nanocomposites were tested by the removal of methylene blue from water in dark and under a simulated sunlight, respectively. By comparison, the improved photocatalytic activity of the CNTs/TiO₂ nanocomposite is mainly due to that the CNTs can disperse the active component of TiO₂ nanoparticles, provide a larger the specific surface area, as well as act as an electron sink to accelerate the separation of the photogenerated charges.     

Synthesis of TiO2/Bi2WO6 nanofibers with electrospinning technique for photocatalytic methyl blue degradation

TiO₂/Bi₂WO₆ composite nanofibers have been successfully synthesized by a simple electrospinning process. XRD, SEM, HR-TEM, nitrogen adsorption–desorption isotherms and UV–visible diffuse reflectance spectra were used to characterize the composite nanofibers. The composite fibers with diameters about 100 nm was composed of nanoparticles and possessed of high specific surface area (49.6 m² g^?1) and porous structure. Besides, the TiO₂/Bi₂WO₆ composite nanofibers exhibited excellent visible photocatalytic property in the photodegradation of methylene blue (MB), and over 97.2 % of MB was degraded within 5.5 h.     

Fabrication of electrospun polyethersulfone/titanium dioxide (PES/TiO2) composite nanofibers membrane and its application for photocatalytic degradation of phenol in aqueous solution

The main objective of this research is to use the photocatalytic properties of PES/TiO₂ nanofibers membranes to remove the phenol as a toxic pollutant in various effluents. The uniform fibers in terms of minimum bead formation and fibers diameter were fabricated. Therefore, more TiO₂ catalysts are on the surface of the fibers which increase the active surface area of nanoparticles and consequently improve the phenol degradation efficiency. The effects of TiO₂ concentration on hydrophilicity, mechanical properties, porosity, mean pore size, and water flux of membranes were studied. The PES/TiO₂ nanofibers were evaluated for phenol degradation under UVA irradiation through a transparent membrane module. The amount of removable phenol was analyzed with high‐performance liquid chromatography. Central composite design was used as a statistical experimental design. Finally, the effect of TiO₂ content in nanofibers and initial phenol concentrations were investigated as well as pH values in synthetic wastewater, on phenol degradation. The results from analysis of variance (ANOVA) analysis indicated that TiO₂ content in nanofibers was the most important and effective parameter on phenol degradation. It was also presented that there is no significant interaction between parameters so that the effect of each parameter was investigated separately. Maximum phenol degradation was 43.0 ± 0.3% and found under conditions of TiO₂ content, initial phenol concentration, and pH value of 8%, 120 ppm, and 7, respectively.     

Novel Bi/BiOBr/AgBr composite microspheres: Ion exchange synthesis and photocatalytic performance

Novel Bi/BiOBr/AgBr composite microspheres were prepared by a rational in situ ion exchange reaction between Bi/BiOBr microspheres and AgNO₃. The characteristic of the as-obtained ternary microspheres was tested by X-ray diffraction (XRD), energy dispersive X-ray spectrometer (EDS), scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV–vis diffuse reflectance spectroscopy (UV–vis DRS) and photoluminescence (PL). Under visible light irradiation, Bi/BiOBr/AgBr microspheres exhibited an excellent photocatalytic efficiency for rhodamine B (RhB) degradation, which was about 1.4 and 4.9 times as high as that of Bi/BiOBr and BiOBr/AgBr, demonstrating that the highest separation efficiency of charge carriers in the heterostructured Bi/BiOBr/AgBr. The photocatalytic activity of Bi/BiOBr/AgBr microspheres just exhibited a slight decrease after three consecutive cycles. The photocatalytic mechanism investigation confirmed that the superoxide radicals (O₂^•−) were the dominant reactive oxygen species for RhB degradation in Bi/BiOBr/AgBr suspension.