Photocatalytic properties of TiO2 sol-gel modified nanocomposite films

TiO₂ nanocomposite films with different concentrations of TiO₂ MT-150A nanoparticles were immobilized on glass substrates using a dip coating process. The crystalline structure and surface chemical state of nanocomposite film properties were examined by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. The specific surface area and morphology of TiO₂ MT-150A nanoparticles were evaluated by the BET method and Field Emission Scanning Electron Microscopy (FE-SEM). The photocatalytic activities of films were evaluated by the methyl orange decoloring rate. XPS measurements showed that the oxygen amount (%) was related to the film composition. The composite film with 10 g/L MT-150A loading yielded the highest amount of surface oxygen (26.82%) and TiO₂ rutile showed the lowest amount of surface oxygen (13.67%) in the form of surface hydroxyl groups. The remaining oxygen was identified as lattice oxygen. In addition, the nanocomposite film with 10 g/L MT-150A loading yielded the highest photocatalytic activity.     

Preparation of TiO2/carbon nanotubes photocatalysts: The influence of the method of oxidation of the carbon nanotubes on the photocatalytic activity of the nanocomposites

A method for the preparation of efficient TiO₂/multi-wall carbon nanotubes nanocomposite photocatalysts by precipitation of anatase TiO₂ nanoparticles onto differently oxidized carbon nanotubes is presented. The precursor compound titanium(IV) bromide was hydrolyzed producing pure anatase phase TiO₂ nanoparticles decorated on the surface of the oxidized carbon nanotubes. The oxidative treatment of the carbon nanotubes influenced the type, quantity and distribution of oxygen-containing functional groups, which had a significant influence on the electron transfer properties, i.e., the photocatalytic activity of the synthesized nanocomposites. The results of C.I. Reactive Orange 16 photodegradation in the presence of all the synthesized nanocomposites showed their better photocatalytic activity in comparison to the commercial photocatalyst Degussa P-25.     

The dependence of the photocatalytic activity of TiO2/carbon nanotubes nanocomposites on the modification of the carbon nanotubes

Nanostructural TiO₂/modified multi-wall carbon nanotubes photocatalysts were prepared by hydrolysis of Ti(iso-OC₃H₇)₄ providing chemical bonding of anatase TiO₂ nanoparticles onto oxidized- or amino-functionalized multi-wall carbon nanotubes (MWCNT). The processes of functionalization of the MWCNT and the deposition of TiO₂ influence the photocatalytic activity of the synthesized nanocomposites. The phase composition, crystallite size, and the structural and surface properties of the obtained TiO₂/modified-MWCNT nanocomposite were analyzed from XRD, FEG-SEM, TEM/HRTEM and FTIR data, as well low temperature N₂ adsorption. In the photocatalytic study, the TiO₂/oxidized-MWCNT catalyst showed the highest and the TiO₂/amino functionalized-MWCNT catalysts somewhat lower degradation rates, indicating that the enhancement of photocatalysis was supported by the more effective electron transfer properties of the oxygen- than amino-containing functional groups, which support the efficient charge transportation and separation of the photogenerated electron-hole pairs.     

Formation of TiO2 nano fibers on a micro-channeled Al2O3-ZrO2/TiO2 porous composite membrane for photocatalytic filtration

In this study, needle-shape TiO₂ fibers were successfully fabricated inside a micro-channeled Al₂O₃-ZrO₂ composite porous membrane system using sol-gel method. The micro-channeled Al₂O₃-ZrO₂ composite was fabricated using the fibrous monolithic (FM) process. Pure anatase phase TiO₂ was crystallized from the as-coated amorphous phase during calcination at 510 °C. The TiO₂ fibers grew on the surface frame of the micro-channeled Al₂O₃-ZrO₂ composite membrane and fully covered the inside of the micro-channeled pores. The specific surface area of the TiO₂ coated membrane system was dramatically increased by over 100 fold compared to that of the non-coated system. The photocatalytic activity of the membrane was also assessed and was shown to very effectively convert organic materials. Thus, this novel membrane holds promise for use as an advanced filtration system.     

Photocatalytic activity of transparent porous glass supported TiO2

A porous glass tube with a composition of 96SiO₂·4B₂O₃ (wt%) supported TiO₂ shows high photooxidation activity due to its transparency and large surface area. The surface area of the porous glass tube supported TiO₂ is 10,000 times larger than that of conventional materials. TiO₂ crystals supported are anatase type. Transparency of the porous glass tube is very important. Herein, sol–gel and chemical vapor deposition (CVD) processes were employed as TiO₂ supporting processes. CVD process is more effective. For instance, an aqueous methylene blue solution with 1 ppm concentration almost thoroughly decomposes at a contact time of 300 s using porous glass tube supported TiO₂ prepared by CVD process under irradiating with 10 W low-pressure mercury lamp, on the other hand, opaque porous alumina tube supported TiO₂ was only 25%. The smaller the pore size of the porous glass tube, the larger the transparency and the permeation resistance through porous glass tube. Hence, porous glass tube with ca. 40 nm pore diameter is suitable from the standpoint of a practical use.     

A rapid method for the preparation of silica-coated ZrO2 nanoparticles by microwave irradiation

A novel synthesis of silica-coated ZrO₂ nanoparticles is reported based on microwave irradiation (MW) method. The synthesis of silica-coated ZrO₂ nanoparticles was realized by a rapid uniform hydrolysis and subsequent copolymerization of the precursor tetraethoxysilane (TEOS) on ZrO₂ surface. One of the advantages of this MW irradiation method is the very short coating time and uniform heating in comparison to the conventional ones, allowing the synthesis of uniformly coated ZrO₂ nanoparticles with silica. The XPS analysis revealed the shifts in binding energies for Zr 3d5/2 and Zr 3d3/2 peaks after coating confirming the formation of silica layer on the surface of ZrO₂ nanoparticles. Characteristic silica peaks were observed in the FTIR spectra of coated nanoparticles. The shift in the isoelectric point measured by dynamic light scattering method was indicator of silica coverage of the ZrO₂ surface. The coatings formed at 70 °C were thin and uniform and extended up to 2 nm from the ZrO₂ surface as confirmed by the HR-TEM images.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Visible photocatalytic activity and photoelectrochemical behavior of TiO2 nanoparticles modified with metal porphyrins containing hydroxyl group

TiO₂ nanoparticles modified with 5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin (HTPP), 5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin zinc (ZnHTPP) and trans-dichloro-5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin tin (SnHTPP) were prepared in order to improve the visible photocatalytic activity of TiO₂ nanoparticles. The photocatalytic activity of the modified TiO₂ nanoparticles was investigated by carrying out the photodegradation of methyl orange in aqueous solution under visible light irradiation. The TiO₂ nanoparticles modified with SnHTPP show the highest visible photocatalytic activity with a degradation ratio of 86% of methyl orange after 180 min irradiation among three catalysts. This result indicates that the central metal ions in porphyrins can significantly influence the sensitization efficiency of porphyrins. In addition, the photoelectrochemical behavior of the modified TiO₂ nanoparticles was examined and related to their photocatalytic activity. Finally, the photocatalytic mechanism was discussed preliminarily.     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.     

Simple fabrication of rod-like N-doped TiO2/Ag with enhanced visible-light photocatalytic activity

Rod-like N-doped TiO₂/Ag composites were successfully synthesized by a modified sol–gel method, without adding any surfactants. The entire preparation differs from the traditional sol–gel synthesis of TiO₂ that the reaction can get controlled by adjusting the flow speed of water vapor and NH₃. Characterization results show that as-prepared samples were uniform nanorods with an average length of ca. 3 µm and a cross section diameter of ca. 150 nm. The rod-like structure was formed during the annealing process. A possible mechanism was proposed to illustrate the formation of rod-like Ag–N–TiO₂. The degradation of methylene blue performed under visible light with the prepared nanorods as the photocatalyst demonstrated the photocatalytic activities of TiO₂ can be improved by the synergistic effect of N doping and Ag modification. In addition, as-prepared TiO₂-based photocatalyst exhibits a significantly enhanced photo-chemical stability after 5 catalytic cycles mainly due to the rod-like morphology. This indicated that they have some potential value in practical application.     

Effect of annealing on the phase transition and morphology of Ag NPs on/in TiO2 rods synthesized by a polyol method

In this study, we report the effect of annealing (250–700 ^oC) on the phase transition and morphology of silver (Ag) nanoparticles (NPs) on/in titanium dioxide (TiO₂) rods prepared using a polyol method. The annealed samples showed not only morphological change, i.e., a solid-to-liquid (melting) transition of Ag NPs due to its partial dissolution into the TiO₂ rods, but also early stage anatase crystallization and anatase–rutile transformation of TiO₂ rods under low annealing temperatures. Such findings, together with XRD and FE-SEM analyses, confirm that, upon higher annealing treatment, diffusion and coalescence leads to changes in the size and shape of the metal particles not only in the outermost regions, but also a random distribution and progressive growth of Ag clusters in the inner interface region. Here, it was shown that annealing can induce changes in morphology, as well as the chemical state and structure of Ag–TiO₂. The present polyol-synthesized Ag–TiO₂ composite also showed improved thermal stability.     

Preparation of photocatalytic TiO2 coatings by gel-dipping with polysaccharides

Commercial tiles are being produced in vast quantities. The main properties of tiles are well established but there is an increasing interest in producing ceramics with tailored-properties and advanced functionalities. One way of adding value to commercial tiles is to deposit a photocatalytic coating to obtain ‘smart’ tiles for environmental reasons, e.g. for the (photo) degradation of organic pollutants in air or in a liquid. Here, we show the manufacture of ‘smart’ tiles by formation of TiO₂ coatings onto commercial tiles by a colloidal processing route based on the immersion of the substrate into a homogeneous aqueous ceramic suspension and its consolidation by agar thermogelation. The effect of the processing parameters (withdrawal rate, solid loading and gelling agent content) and the grain size on the photocatalytic activity of the final coated tiles is reported and discussed. Final coatings properties depend on the viscosity of the suspension, particle size, withdrawal rate, solid loading and gelling agent content, and hence, this dependence affects the photocatalytic activity of the coatings.     

TiO2 as a sintering additive for KNbO3 ceramics

Improved densification during the conventional sintering of KNbO₃ ceramics was achieved by using small additions of TiO₂. This improved densification can be explained on the basis of high-temperature chemical reactions in the system. X-ray diffractometry and electron microscopy were used in combination with diffusion-couple experiments in order to elucidate the chemical reactions between KNbO₃ and TiO₂. TiO₂ reacts with KNbO₃ forming KNbTiO₅, and a low concentration of Ti incorporates in the KNbO₃ structure resulting in the formation of oxygen vacancies and, consequently, in an improvement in the densification. At ∼1037 °C eutectic melting between the KNbO₃ and the KNbTiO₅ further improves the densification of the KNbO₃ ceramics.     

Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.     

Spontaneously ordered TiO2 nanostructures

Titanium dioxide thin films were deposited on quartz substrates kept at different O₂ pressures using pulsed laser deposition technique. The effects of reactive atmosphere and annealing temperature on the structural, morphological, electrical and optical properties of the films are discussed. Growth of films with morphology consisting of spontaneously ordered nanostructures is reported. The films growth under an oxygen partial pressure of 3 × 10⁻⁴ Pa consist in nanoislands with voids in between them whereas the film growth under an oxygen partial pressure of 1 × 10⁻⁴ Pa, after having being subjected to annealing at 500 °C, consists in nanosized elongated grains uniformly distributed all over the surface. The growth of nanocrystallites with the increase in annealing temperature is explained on the basis of the critical nuclei-size model.     

Effect of pre-nitridation treatment on the formation of anatase TiO2 films by anodization

High performance-anatase TiO₂ films were successfully formed on metallic titanium by anodization in an acidic electrolyte composed of H₂SO₄, H₃PO₄ and H₂O₂ subsequent to pre-nitridation treatment. The pre-nitridation treatment was carried out by pre-annealing metallic titanium under a nitrogen atmosphere of 0.1 MPa. The anodized films showed photocatalytic activity in photooxidization of the iodide anion into the tri-iodide anion. The nitridation treatment had a significant effect not only on the formation of anatase TiO₂ films but also on the photocatalytic activity of the anodized films.     

Synthesis, characterization and photocatalytic properties of sol-gel TiO2 films

The application of heterogeneous photocatalysis is described as an advanced oxidation process (AOP) for the degradation of the diazo reactive dye using immobilized TiO₂ as a photocatalyst. Starting TiO₂ solutions were prepared with and without the addition of polyethylene glycol (PEG) and TiO₂ films were directly deposited on a borosilicate glass substrate using the sol-gel dip-coating method. The surface morphology and the nanoscale roughness of TiO₂ films were studied by means of atomic force microscopy (AFM). Structural properties of TiO₂ were identified by X-ray diffraction (XRD). The decomposition behaviour of organic compounds from the gels was investigated using thermal gravimetry (TG) and differential scanning calorimetry (DSC). Photocatalytic activities of TiO₂ films in the process of degradation of the commercial diazo textile dye Congo red (CR), used as a model pollutant, were monitored by means of UV/vis spectrophotometry. The kinetics of the degradation of the CR dye was described with the Langmuir-Hinshelwood (L-H) kinetic model.The addition of PEG to the TiO₂ solution resulted in the changes in the film surface morphology, and affected the ratio of anatase-rutile crystal phases and the photocatalytic activity of TiO₂. The TiO₂ film prepared with PEG is characterized by higher roughness parameters (R_a, R_max, R_q, R_z and Z_max), a lower amount of the rutile phase of TiO₂, a higher amount of the anatase phase of TiO₂ and a better photocatalytic activity compared to the TiO₂ film without the addition of PEG.     

Coloured TiO2 based glazing obtained by spray pyrolysis for solar thermal applications

Titanium dioxide thin films with coloured reflections were deposited on glass substrate by robotic spray pyrolysis deposition using titanium (IV) isopropoxide as a precursor and air as a carrier gas. The films' optical properties were analyzed by UV–vis–NIR spectrometry using a 150 mm integrating sphere and spectroscopic ellipsometry (SE). The surface properties were evaluated by atomic force microscopy (roughness and morphology) and contact angle measurement (wettability). The colour variation of the films was determined in the CIE (Commission Internationale d'Eclairage) L^?a^?b^? colour system by using the total reflectance spectra measured in the visible range.