Treatment of Wastewater with High Conductivity by Pulsed Discharge Plasma

A wastewater treatment system was established by means of pulsed dielectric barrier discharge（DBD）. The main advantage of this system is that the wastewater is employed as one of the electrodes for the degradation of rhodamine B, which makes use of the high conductivity and lessenes its negative influence on the discharge process. At the same time, the reactive species like ozone and ultraviolet（UV） light generated by the DBD can be utilized for the treatment of wastewater. The effects of some factors like conductivity, peak pulse voltage, discharge frequency and pH values were investigated. The results show that the combination of these reactive species could enhance the degradation of the dye while the ozone played the most important role in the process. The degradation efficiency was enhanced with the increase of energy supplied. The reduction in the concentration of rhodamine B was much more effective with high solution conductivity;under the highest conductivity condition, the degradation rate could rise to 99%.     

Degradation of Benzene by Using a Silent-Packed Bed Hybrid Discharge Plasma Reactor

In this work,a novel gas phase silent-packed bed hybrid discharge plasma reactor has been proposed,and its ability to control a simulative gas stream containing 240 ppm benzene is experimentally investigated.In order to optimize the geometry of the reactor,the benzene conversion rate and energy yield(EY) were compared for various inner electrode diameters and quartz tube shapes and sizes.In addition,benzene removal efficiency in different discharge regions was qualitatively analyzed and the gas parameter(space velocity) was systematically studied.It has been found that silent-packed bed hybrid discharge plasma reactor can effectively decompose benzene.Benzene removal proved to achieve an optimum value of 60% with a characteristic energy density of 255 J/L in this paper with a 6 mm bolt high-voltage electrode and a 13 mm quartz tube.The optimal space velocity was 188.1 h-1,which resulted in moderate energy yield and removal efficiency.Reaction by-products such as hydroquinone,heptanoic acid,4-nitrocatechol,phenol and 4-phenoxy-phenol were identified by mean of GC-MS.In addition,based on these organic by-products,a benzene destruction pathway was proposed.     

Treatment of Dyeing Wastewater by Using Positive Pulsed Corona Discharge to Water Surface

This study investigated the treatment of textile-dyeing wastewater by using an electrical discharge technique （positive pulsed corona discharge）. The high-voltage electrode was placed above the surface Of the wastewater while the ground electrode was submerged in the wastewater. The electrical discharge starting at the tip of the high voltage electrode propagated toward the surface of the wastewater, producing various oxidative radicals and ozone. Oxygen was used as the working gas instead of air to prevent nitrogen oxides from forming. The simulated wastewater was made up with amaranth, which is a kind of azo dye. The results obtained showed that the chromaticity of the wastewater was almost completely removed within an hour. The ultraviolet/visible spectra of the wastewater treated by the electrical discharge revealed that the total hydrocarbon level also decreased significantly.     

Degradation of Dye Wastewater by Pulsed High-Voltage Discharge Combined with Spent Tea Leaves

Degradation of methylene blue （MB） was performed using the pulsed discharge process （PDP） combined with spent tea leaves （STLs）. The effects of STL dosage, concentration of initial solution, and pH were analyzed in the combined treatment. Results showed that the combined treatment was effective for dye wastewater degradation; when the dosage of STLs was 3.2 g/L, the degradation efficiency reached 90% after 15 rain treatment, and STLs showed a good repeatability. The degradation rate decreased with increasing initial MB concentration but not related to the solution pH in the combined treatment. Fourier-transform infrared spectra and N2 adsorption suggested that the number of acidic and basic groups in the STL surface increased after the treatment, but the surface area and pore volume remained unchanged.     

Discharge Characteristics of Series Surface/Packed-Bed Discharge Reactor Diven by Bipolar Pulsed Power

The discharge characteristics of the series surface/packed-bed discharge(SSPBD)reactor driven by bipolar pulse power were systemically investigated in this study.In order to evaluate the advantages of the SSPBD reactor,it was compared with traditional surface discharge(SD) reactor and packed-bed discharge(PBD) reactor in terms of the discharge voltage,discharge current,and ozone formation.The SSPBD reactor exhibited a faster rising time and lower tail voltage than the SD and PBD reactors.The distribution of the active species generated in different discharge regions of the SSPBD reactor was analyzed by optical emission spectra and ozone analysis.It was found that the packed-bed discharge region(3.5 mg/L),rather than the surface discharge region(1.3 mg/L) in the SSPBD reactor played a more important role in ozone generation.The optical emission spectroscopy analysis indicated that more intense peaks of the active species(e.g.N_2 and OI) in the optical emission spectra were observed in the packed-bed region.     

Experiment and Analysis on the Treatment of Gaseous Benzene Using Pulsed Corona Discharge Plasma

An experiment and analysis on removal of gaseous benzene by pulse corona inducedplasma is presented in this article. Important parameters effecting removal efficiency have been investigated, such as pulse peak voltage, pulse frequency, gas inlet concentration, gas flow rate and reactor temperature. The result shows that the removal efficiency increases with the increase in pulse peak voltage, pulse frequency and reactor temperature, but decreases in the rise of gas inlet concentration and gas flow rate. On the condition of Vp = 36 kV, f = 80 Hz, C = 1440 mg/m^3 and Q = 640 ml/min, the largest removal efficiency is 98%. Finally, the reacted products are qualitatively analysed and the reaction processes are deduced in combination with plasma-chemistry theory.     

Plasma Discharge Process in a Pulsed Diaphragm Discharge System

As one of the most important steps in wastewater treatment, limited study on plasma discharge process is a key challenge in the development of plasma applications. In this study, we focus on the plasma discharge process of a pulsed diaphragm discharge system. According to the analysis, the pulsed diaphragm discharge proceeds in seven stages： （1） Joule heating and heat exchange stage; （2） nucleated site formation; （3） plasma generation （initiation of the breakdown stage）; （4） avalanche growth and plasma expansion; （5） plasma contraction; （6） termination of the plasma discharge; and （7） heat exchange stage. From this analysis, a critical voltage criterion for breakdown is obtained. We anticipate this finding will provide guidance for a better application of plasma discharges, especially diaphragm plasma discharges.     

Degradation of Acid Orange 7 Dye in Two Hybrid Plasma Discharge Reactors

To get an optimized pulsed electrical plasma discharge reactor and to increase the energy utilization efficiency in the removal of pollutants, two hybrid plasma discharge reactors were designed and optimized. The reactors were compared via the discharge characteristics, energy transfer efficiency, the yields of the active species and the energy utilization in dye wastewater degradation. The results showed that under the same AC input power, the characteristics of the discharge waveform of the point-to-plate reactor were better. Under the same AC input power, the two reactors both had almost the same peak voltage of 22 kV. The peak current of the point-to-plate reactor was 146 A, while that of the wire-to-cylinder reactor was only 48.8 A. The peak powers of the point-to-plate reactor and the wire-to-cylinder reactor were 1.38 MW and 1.01 MW, respectively. The energy per pulse of the point-to-plate reactor was 0.2221 J, which was about 29.4% higher than that of the wire-to-cylinder reactor （0.1716 J）. To remove 50% Acid Orange 7 （AO7）, the energy utilizations of the point-to-plate reactor and the wire- to-cylinder reactor were 1.02×10^-9 mol/L and 0.61×10^-9 mol/L, respectively. In the point-to- plate reactor, the concentration of hydrogen peroxide in pure water was 3.6 mmol/L after 40 min of discharge, which was higher than that of the wire-to-cylinder reactor （2.5 mmol/L）. The concentration of liquid phase ozone in the point-to-plate reactor （5.7×10^-2 mmol/L） was about 26.7% higher than that in the wire-to-cylinder reactor （4.5×10^-2 mmol/L）. The analysis results of the variance showed that the type of reactor and reaction time had significant impacts on the yields of the hydrogen peroxide and ozone. The main degradation intermediates of AO7 identified by gas chromatography and mass spectrometry （GCMS） were acetic acid, maleic anhydride, p- benzoquinone, phenol, benzoic acid, phthalic anhydride, coumarin and 2-naphthol. Proposed degradation pathways were elucidated in light of the ana     

Degradation of Dye Wastewater by ns-Pulse DBD Plasma

Two plasma reactors have been developed and used to degrade dye wastewater agents.The configuration of one plasma reactor is a comb-like extendable unit module consisting of 5 electrodes covered with a quartz tube and the other one is an array reactor which is extended from the unit module.The decomposition of wastewater by ns pulse dielectric barrier discharge(DBD) plasma have been carried out by atomizing the dyeing solutions into the reactors.During experiments,the indigo carmine has been treated as the waste agent.The measurements of UV-VIS absorption spectroscopy and the chemical oxygen demand(COD) are carried out to demonstrate the decomposition efect on the wastewater.It shows that the decoloration rate of 99% and the COD degradation rate of 65% are achieved with 15 min treatment in the unit reactor.The efect of electrical parameters on degradation has been studied in detail.Results from the array reactor indicate that it has a better degradation efect than the unit one.It can not only totally remove the chromogenic bond of the indigo carmine solution,but also efectively degrade unsaturated bonds.The decoloration rate reaches 99% after 10 min treatment,the decomposition rate of the unsaturated bond reaches 83% after 60 min treatment,and the COD degradation rate is nearly 74%.     

Degradation of Anionic Dye Eosin by Glow Discharge Electrolysis Plasma

This paper describes a novel method for the degradation of eosin by using glow discharge electrolysis （GDE）. The effects of various parameters on the removal efficiency were studied. It was found that the eosin degradation could be raised considerably by increasing the applied voltage and the initial concentration, or by decreasing pH of the aqueous solution. Fe^2＋ ion had an evident accelerating effect on the eosin degradation. The degradation process of eosin obeyed a pseudo-first-order reaction. The relationship between the degradation rate constant k and the reaction temperature T could be expressed by Arrhenius equation with which the apparent activation energy Ea of 14.110 kJ· mol^-1 and the pre-exponential factor k0 of 2.065× 10^-1 min^-1 were obtained, too. The determination of hydroxyl radical was carried out by using N, N-dimethyl -p-nitrosoaniline （RNO） as a scavenger. The results showed that the hydroxyl radical plays an important role in the degradation process.     

Surface Treatment of Polypropylene Powders Using a Plasma Reactor with a Stirrer

A radio frequency argon plasma reactor with a stirrer was employed for the surface treatment of polypropylene (PP) powders. The changes in the superficial contact angle and the superficial composition of the un-treated and treated PP powders were analyzed by means of water contact angle (WCA) measurement, X-ray photoelectron spectroscopy (XPS) and attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR). The water contact angle changed from the original value of 130.2° before plasma treatment to the value of 73.6° after treatment for 5 minutes. With the increase in plasma treating time, there were a decrease in the water contact angle and an increase in the content of oxygen containing polar functional groups (i.e., C-O, C=O and O-C=O). Both XPS and ATR-FTIR results indicated that the plasma treatment led to the formation of oxygen containing polar functional groups due to oxidation on the surface of the PP powders, and the trend of variation of the water contact angle with plasma treating time was related to the concentration of oxygen atom on the treated PP powders surface. Furthermore, the aging of the plasma-treated PP powders was investigated.     

Synergistic Decolouration of Azo Dye by Pulsed Streamer Discharge Immobilized TiO2 Photocatalysis

Photocatalyst was prepared by immobilizing TiO2 on glass beads using the traditional sol-gel method. Ultraviolet light （UV） produced by pulsed streamer discharge was then used to induce photocatalytic activity of TiO2 photocatalyst. Decolouration efficiency of the representative azo dye （acid orange 7, AOT） was investigated using the synergistic system of pulsed streamer discharge plasma and TiO2 photocatalysis. The obtained results showed that the decolouration rate of AO7 could be increased by 16.7% under the condition of adding supported TiO2 in the pulsed streamer discharge system, compared to that in the sole pulsed streamer discharge plasma system, due to the synergistic effect of pulsed streamer discharge and TiO2 photocatalysis induced by pulsed streamer discharge. The synergistic system of pulsed streamer discharge and TiO2 photocatalyst was found to have more reactive radicals for degradation of organic compounds in water.     

Treatment of Invasive Marine Species on Board by Using Micro-gap Discharge Plasma

A pilot-scale experiment of 20t/h for the treatment of ship＇s ballast water is reported in this paper. When the concentration of the dissolved OH. was 0.68 mg/L during the experiment, the rate of destroying bacteria, mono-algae, protozoan reached 100% within 2.67 s. The effect of hydroxyl radicals on biochemical processes was also studied. The attenuation rate of photosynthesis pigment was 100%. And the main reason for the cells＇ death was the strong destruction of the monose, amylose, protein, DNA and RNA in the cells. As an advanced oxidation method, the procedure can destroy invasive marine species when a ship is in the process of discharging its ballast water.     

Improvement on Diamond Nucleation Treated by Pulsed Arc Discharge Plasma

A technique of improvement on diamond nucleation based on pulsed arc discharge plasma at atmospheric pressure was developed. The pulsed arc discharge was induced respectively by nitrogen, argon and methanol gas. After the arc plasma pretreatment, a nucleation density higher than 10^10 cm^-2 may be obtained subsequently in chemical vapor deposition (CVD) on a mirror-polished silicon substrate without any other mechanical treatment. The effects of the arc discharge plasma on the diamond nucleation were investigated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), infrared spectroscopy (IR) and Raman spectroscopy. The enhancement of nucleation is postulated to be a result of the formation of carbonlike phase materials or nitrogenation on the substrate surface without surface defect produced by arc discharge.     

Inactivation of Bacteria in Oil Field Injected Water by a Pulsed Plasma Discharge Process

Pulsed plasma discharge was employed to inactivate bacteria in the injection water for an oil field.The effects of water conductivity and initial concentration of bacteria on elimination efficiency were investigated in the batch and continuous flow modes.It was demonstrated that Fe~(2+) contained in injection water could enhance the elimination efficiency greatly.The addition of reducing agent glutathione(GSH) indicated that active radicals generated by pulsed plasma discharges played an important role in the inactivation of bacteria.Moreover,it was found that the microbial inactivation process for both batch and continuous flow mode well fitted the model based on the Weibull's survival function.     

Mechanism of Phase Transition from Liquid to Gas under Dielectric Barrier Discharge Plasma

Liquid gasification phenomenon was observable in liquid-solid dielectric barrier discharge (DBD) experiments. Starting from classical thermodynamics, this study aimed at finding the reason of liquid gasification in the DBD experiments. Fluid statics and electrohydrodynamics were adopted to analyze the mechanism of phase transition from liquid to gas. The Sumoto effect was also employed to visually explain the change in the pressure of fluid due to the electric field. It was concluded from both theoretical analysis and experiment that the change in liquid pressure was a key factor causing liquid to gasify in DBD conditions. Furthermore, it was stressed that the liquid pressure was affected by many parameters including liquid permittivity, voltage, electric intensity, size of the discharge space and uniformity of the electric field distribution, etc. All of them affected DBD liquid gasification. The related results would provide useful theoretical evidence for multi- phase DBD applications.     

Temperature and Nitric Oxide Generation in a Pulsed Arc Discharge Plasma

Nitric oxide （NO） is increasingly being used in medical treatments of high blood pressure, acute respiratory distress syndrome and other illnesses related to the lungs. Currently a NO inhalation system consists of a gas cylinder of N2 mixed with a high concentration of NO. This arrangement is potentially risky due to the possibility of an accidental leak of NO from the cylinder. The presence of NO in the air leads to the formation of nitric dioxide （NO2）, which is toxic to the lungs. Therefore, an on-site generator of NO would be highly desirable for medical doctors to use with patients with lung disease.
To develop the NO inhalation system without a gas cylinder, which would include a high concentration of NO, NAMIHIRA et al have recently reported on the production of NO from room air using a pulsed arc discharge. In the present work, the temperature of the pulsed arc discharge plasma used to generate NO was measured to optimize the discharge condition. The results of the temperature measurements showed the temperature of the pulsed arc discharge plasma reached about 10,000 K immediately after discharge initiation and gradually decreased over tens of microseconds. In addition, it was found that NO was formed in a discharge plasma having temperatures higher than 9,000 K and a smaller input energy into the discharge plasma generates NO more efficiently than a larger one.     

Achieving Better NOx Removal in Discharge Plasma Reactor by Field Enhancement

Application of plasma chemistry for gas cleaning is gaining prominence in recent years, mainly from an energy efficiency point of view. In this paper we conducted a comparative study of NO/NOx removal using two different types of dielectric barrier discharge electrodes, wire- cylinder reactor, pipe-cylinder reactor. Investigations were first carried out with synthetic gases to obtain the baseline information on the NO/NOx removal with respect to the two geometries studied. Further, experiments were carried out with raw diesel exhaust under loaded condition. A high NOx removal efficiency of 90% was observed for the pipe-cylinder reactor as compared to that of 53.4% for the wire-cylinder reactor. Furthermore, for the same energy consumed per NO molecule （about 73 eV/NO molecule）, the removal efficiency increased from 67% for the wire- cylinder to about 98% for the pipe-cylinder which was quite appreciable.     

Enhanced by Dielectric Barrier Discharge Plasma Pretreatment Irradiated by High-Intensity Pulsed Ion Beam

In order to develop a more economical pretreatment method for electroless nickel plating, a dielectric barrier discharge (DBD) plasma at atmospheric pressure was used to improve the hydrophilicity and adhesion of poly (ethylene terephthalate) (PET) nonwoven fabric. The properties of the PET nonwoven fabric including its liquid absorptive capacity (WA), aging behavior, surface chemical composition, morphology of the surface, adhesion strength, surface electrical resistivity and electromagnetic interference (EMI)- shielding effectiveness (SE) were studied. The liquid absorptive capacity (WA) increased due to the incorporation of oxygen-containing and nitrogen-containing functional groups on the surface of PET nonwoven fabric after DBD air-plasma treatment. The surface morphology of the nonwoven fibers became rougher after plasma treatment. Therefore, the surface was more prone to absorb tin sensitizer and palladium catalyst to form an active layer for the deposition of electroless nickel. SEM and X-ray diffraction (XRD) measurements indicated that a uniform coating of nickel was formed on the PET nonwoven fabric. The average EMI-SE of Ni-plating of PET nonwoven fabric maintained a relatively stable value (38.2 to 37.3 dB) in a frequency range of 50 to 1500 MHz. It is concluded that DBD is feasible for pretreatment of nonwoven fabric for electroless nickel plating to prepare functional material with good EMI-SE properties.