Surface and electrical characteristics of poly(amide imide)–poly(dimethylsiloxane) nanocomposites

A series of poly(amide imide)–poly(dimethylsiloxane) (PDMS) nanocomposites were fabricated through the reaction of poly(amide imide), epoxysilane (coupling agent), and diethoxydimethylsilane (DEDMS) via a sol–gel process. Nanocomposite films were obtained through the hydrolysis and condensation of DEDMS in poly(amide imide) solutions. The existence of the condensation product of DEDMS in the poly(amide imide) matrix was confirmed with Fourier transform infrared (FTIR). The concentration of PDMS on the surface of the poly(amide imide) matrix was observed through a comparison of FTIR and attenuated total reflection spectra. The contact angle of the poly(amide imide)–PDMS composites increased more than 40° with respect to that of pure poly(amide imide). The alternating‐current (ac) breakdown strength was obtained through the measurement of the ac breakdown voltage at the temperature of liquid nitrogen. As the PDMS concentration in poly(amide imide) increased, the characteristics of the insulation breakdown improved greatly. The best ac breakdown strength was observed in a poly(amide imide)–epoxysilane (30 wt %) nanocomposite with 30 wt % PDMS. The samples at the temperature of liquid nitrogen were brittle, as in a glassy state. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 342–347, 2004     

Influence of organic modification on mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites

The influence of organic modifiers on intercalation extent, structure, thermal and mechanical properties of poly(methyl methacrylate) (PMMA)–clay nanocomposites were studied. Two different organic modifiers with varying hydrophobicity (single tallow versus ditallow) were investigated. The nanocomposites were prepared from melt processing method and characterized using wide angle X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, differential scanning calorimetry (DSC), and tensile tests. Mechanical properties such as tensile modulus (E), break stress (σ_brk), and % break strain (ε_brk) were determined for nanocomposites at various clay loadings. Extent of PMMA intercalation is sufficient and in the range 9–15 Å depending on organoclay and filler loading. Overall thermal stability of nanocomposites increases by 16–30°C. The enhancement in T_g of nanocomposite is merely by 2–4°C. With increase in clay loading, tensile modulus increases linearly while % break strain decreases. Break stress is found to increase till 4 wt % and further decreases at higher clay loadings. The overall improvement in thermal and mechanical properties was higher for the organoclay containing organic modifier with lower hydrophobicity and single tallow amine chemical structure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of poly(oxyalkylene)amines on structure and properties of epoxide nanocomposites

A shortcoming of most polymer nanocomposites is relatively low toughness. An effective method to eliminate this is the use of a suitable combination of polymeric impact modifiers with organoclay, which may impart synergistic effects on the mechanical behavior of both thermoplastic and thermoset matrix nanocomposites. This work focuses on the effect of various combinations of amine-terminated (APOP) and hydroxyl-terminated poly(oxypropylene) (POP) and layered silicates on the structure and mechanical behavior of epoxy nanocomposites. The combination of APOP and POP with 0.5−5% wt % of organoclay leads to some compositions that produce well balanced mechanical behavior of the epoxy nanocomposite. The higher toughening effectiveness of APOP/montmorillonite (MMT) compared with that of POP/MMT is a consequence of formation of blended domains consisting of clay tactoids and fine APOP inclusions. An increase in the dispersed particle size with clay content was observed to be a consequence of more significant clay-induced nucleation of phase separation at the expense of clay-induced accelerated curing. The best mechanical behavior was observed for materials using an adduct of APOP and MMT, which was obtained using the ion exchange of sodium ions of MMT by protonated APOP. The enhanced mechanical behavior was due to the formation of nanosized planar arrays by self-pilling of elastomer-modified clay and the corresponding increase in the T_g of the epoxy. The structure/property relationships of these systems indicate that this type of clay polymer combination provides an effective way of modifying the mechanical behavior of epoxy nanocomposites. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of vanadium pentoxide on the mechanical,thermal, and electrical properties of poly(vinyl alcohol)/vanadium pentoxide nanocomposites

In this study, we examined the effect of vanadium pentoxide (V₂O₅) on the mechanical, thermal, and morphological properties of poly(vinyl alcohol) (PVA)/V₂O₅ nanocomposites. The PVA/V₂O₅ nanocomposites were prepared by solution mixing, followed by film casting. The results show that the Young's moduli of the resulting nanocomposites films were higher than the pure PVA modulus with increasing V₂O₅ content, and it reached a maximum point at about 0.4 wt % V₂O₅ content at 8.55 GPa. The tensile strength and stress at break increased with increasing V₂O₅ content. The addition of V₂O₅ did not affect the melting temperature. The crystallization temperatures of PVA were significantly changed with increasing V₂O₅ content. The 5% weight loss degradation temperature of the nanocomposites was measured by thermogravimetric analysis. The degradation temperatures of the V₂O₅ nanocomposites increased with increasing filler content and were higher than the degradation temperature of pure PVA; this showed a lower thermal stability compared to those of the nanocomposites. The results show that the thermal stability increased with the incorporation of V₂O₅ nanoparticles. The dielectric constant of PVA had a tendency to improve when the dispersion of particles was effective. The morphology of the surfaces the nanocomposites was examined by scanning electron microscopy. We observed that the dispersion of the V₂O₅ nanoparticles was relatively good; only few aggregations existed after the addition of the V₂O₅ nanoparticles at greater than 0.4 wt %. In perspective, the addition of 0.4 wt % V₂O₅ nanoparticles into PVA maximized the mechanical, thermal, and electrical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Development of unsaturated polyester matrix – carbon nanofibers nanocomposites with improved electrical properties

In this work, the dispersion of carbon nanofibers (CNFs) in an unsaturated polyester (UP) resin was performed by mean of the calendering process. The calendering process allows to obtain good dispersion of the nanoparticles, and, with respect to the other techniques, is also possible to scale it up at the industrial level. Optimization of the calendering conditions for the processing was carried out as a first step of this study. Optimization, in this case, means to reach the best dispersion level, as rapidly as possible and with the lowest amount of styrene evaporation. The dispersion level reached was investigated by the technique of scanning electron microscopy. The investigation on electric conductivity of the nanocomposites at different CNF concentrations has revealed that the electrical percolation threshold exists at around 0.3 wt %, where electrical conductivity switches from 10^?13 to 10^?7 S/cm. The rheological characterization has been performed to verify if the improved electrical properties are obtained at the expense of loss of workability, that is a significant increase of viscosity. Eventually, a mechanical characterization was carried out. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal and mechanical properties of plasticized poly(L‐lactide) nanocomposites with organo‐modified montmorillonites

Nanocomposites of poly(lactide) (PLA) and the PLA plasticized with diglycerine tetraacetate (PL‐710) and ethylene glycol oligomer containing organo‐modified montmorillonites (ODA‐M and PGS‐M) by the protonated ammonium cations of octadecylamine and poly(ethylene glycol) stearylamine were prepared by melt intercalation method. In the X‐ray diffraction analysis, the PLA/ODA‐M and plasticized PLA/ODA‐M composites showed a clear enlargement of the difference of interlayer spacing between the composite and clay itself, indicating the formation of intercalated nanocomposite. However, a little enlargement of the interlayer spacing was observed for the PLA/PGS‐M and plasticized PLA/PGS‐M composites. From morphological studies using transmission electron microscopy, a finer dispersion of clay was observed for PLA/ODA‐M composite than PLA/PGS‐M composite and all the composites using the plasticized PLA. The PLA and PLA/PL‐710 composites containing ODA‐M showed a higher tensile strength and modulus than the corresponding composites with PGS‐M. The PLA/PL‐710 (10 wt %) composite containing ODA‐M showed considerably higher elongation at break than the pristine plasticized PLA, and had a comparable tensile modulus to pure PLA. The glass transition temperature (T_g) of the composites decreased with increasing plasticizer. The addition of the clays did not cause a significant increase of T_g. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Thermal and mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites over a wide range of filler loading

BACKGROUND: Poly(methyl methacrylate) (PMMA)–organoclay nanocomposites with octadecylammonium ion‐modified montmorillonite, prepared via melt processing, over a wide range of filler loading (2–16 wt%) were investigated in detail. These hybrids were characterized for their dispersion structure, and thermal and mechanical properties, such as tensile modulus (E), break stress (σ_brk), percent break strain (ε_brk) and ductility (J), using wide‐angle X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile and impact tests. RESULTS: Intercalated nanocomposites were formed even in the presence of 16 wt% clay (high loading) in PMMA matrix. PMMA intercalated into the galleries of the organically modified clay, with a change in d‐spacing in the range 11–16 Å. TGA results showed improved thermal stability of the nanocomposites. The glass transition temperature (T_g) of the nanocomposites, from DSC measurements, was 2–3 °C higher than that of PMMA. The ultimate tensile strength and impact strength decreased with increasing clay fraction. Tensile modulus for the nanocomposites increased by a significant amount (113%) at the highest level of clay fraction (16 wt%) studied. CONCLUSION: We show for the first time the formation of intercalated PMMA nanocomposites with alkylammonium‐modified clays at high clay loadings (>15 wt%). Tensile modulus increases linearly with clay fraction, and the enhancement in modulus is significant. A linear correlation between tensile strength and strain‐at‐break is shown. Thermal properties are not affected appreciably. Organoclay can be dispersed well even at high clay fractions to form nanocomposites with superior bulk properties of practical interest. Copyright © 2007 Society of Chemical Industry     

Layer‐structured poly(vinyl alcohol)/graphene oxide nanocomposites with improved thermal and mechanical properties

Layer‐structured poly(vinyl alcohol)/graphene oxide nanocomposites in the form of films are prepared by simple solution processing. The structure and properties of these nanocomposites are studied using X‐ray diffractions, scanning electron microscopy, Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. The results indicate that graphene oxide is dispersed on a molecular scale and aligned in the poly(vinyl alcohol) matrix, and there exists strong interfacial interactions between both components, which are responsible for the significant improvement in the thermal and mechanical properties of the nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties and structures of dicyanate–clay nanocomposites

Dicyanate–clay nanocomposites comprising a dicyanate resin and a type of organically modified clay were prepared and characterized, and their thermomechanical properties were investigated. The organically modified clay had silicate layers of nanometer size intercalated with an organic modifier, which improved the compatibility between the clay and organic materials, such as dicyanate resins. Dynamic mechanical analysis was performed to investigate the thermomechanical properties of the dicyanate–clay nanocomposites containing various amounts of the clay. The storage modulus of the nanocomposites below their glass‐transition temperatures slightly increased with increasing clay content. The glass‐transition temperature of the dicyanate–clay nanocomposites increased with increasing clay content. The nanostructures of the dicyanate–clay nanocomposites were characterized by transmission electron microscopy and X‐ray diffraction analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2629–2633, 2003     

Dielectric properties and structures of melt‐compounded poly(ethylene oxide)–montmorillonite nanocomposites

The dielectric dispersion and relaxation process in melt‐compounded hot‐pressed poly(ethylene oxide) (PEO)–montmorillonite (MMT) clay nanocomposite films of 0–20 wt % MMT concentration were investigated over the frequency range 20 Hz to 1 MHz at ambient temperature. X‐ray diffraction study of the nanocomposites evidences that the PEO has been intercalated into the MMT interlayer galleries with a helical‐type multilayer structures, which results the formation of unique parallel plane PEO–MMT layered structures. The relaxation times corresponding to PEO chain segmental motion were determined from the loss peak frequencies of different dielectric formalisms and the same is used to explore the interactions compatibility between PEO molecules and the MMT nano platelets. It is revealed that the loading of only 1 wt % MMT in PEO matrix significantly increases the PEO chain segmental motion due to intercalation, which further varies anomalously with increase of MMT concentration. The real part of dielectric function at 1 MHz, relaxation time, and dc conductivity of these melt‐compounded nanocomposites were compared with the aqueous solution‐cast PEO–MMT films. Considering the comparative changes in the values of various dielectric parameters, the effect of synthesization route on the intercalated/exfoliated‐MMT structures and the PEO chain dynamics were discussed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal and mechanical properties of poly(butylene succinate) nanocomposites with various organo‐modified montmorillonites

Nanocomposites based on biodegradable poly(butylene succinate) (PBS) and layered silicates were prepared by melt intercalation. Nonmodified montmorillonite (MMT) and MMTs (DA‐M, ODA‐M, ALA‐M, LEA‐M, and HEA‐M) organo‐modified by protonated ammonium cations {i.e., those of dodecylamine, octadecylamine, 12‐aminolauric acid, N‐lauryldiethanolamine, and 1‐[N,N‐bis(2‐hydroxyethyl)amino]‐2‐propanol, respectively} were used as layered silicates. From morphological studies using transmission electron microscopy, DA‐M, ODA‐M, and LEA‐M were found to be dispersed homogeneously in the matrix polymer, whereas some clusters or agglomerated particles were observed for ALA‐M, HEA‐M, and MMT. The enlargement of the difference in the interlayer spacing between the clay and PBS/clay composite, as measured by X‐ray diffraction, had a good correlation with the improvement of the clay dispersion and with the increase in the tensile modulus and the decrease in the tensile strength of the PBS composites with an inorganic concentration of 3 wt %. Dynamic viscoelastic measurements of the PBS/LEA‐M nanocomposite revealed that the storage modulus and glass‐transition temperature increased with the inorganic concentration (3–10 wt %). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1463–1475, 2004     

Effect of heat treatment on the electrical properties of lead zirconate titanate/poly (vinylidene fluoride) composites

Ceramic/polymer composites are attracting increasing interest in materials research and practical applications due to the combination of excellent electric properties of piezoelectric ceramics and good flexibility of polymer matrices. In this case, the crystallization of the polymer has a significant effect on the electric properties of ceramic/polymer composites. Based on different heat treatment methods, the crystallization of poly(vinylidene fluoride) (PVDF) in composites of lead zirconate titanate (PZT) and PVDF can be controlled effectively. PZT/PVDF composites with various PVDF crystallizations exhibit distinctive dielectric and piezoelectric properties. When the crystallization of PVDF is 21%, the PZT/PVDF composites show a high dielectric constant (ε) of 165 and a low dielectric loss (tan δ) of 0.03 at 10³ Hz, and when the crystallization of PVDF reaches 34%, the piezoelectric coefficient (d₃₃) of PZT/PVDF composites can be up to ca 100 pC N^?1. By controlling the crystallization of PVDF, PZT/PVDF composites with excellent dielectric and piezoelectric properties were obtained, which can be employed as promising candidates in high‐efficiency capacitors and as novel piezoelectric materials. Copyright © 2010 Society of Chemical Industry     

Production and properties of solvent‐cast poly(ε‐caprolactone) composites with carbon nanostructures

Composites based on carbon nanostructures (CNS) and poly(ε‐caprolactone) (PCL) were produced by solvent casting technique. Single‐walled carbon nanotubes (SWCNTs) and carbon nanofibers (CNFs) were selected, to produce composite films with enhanced properties. The role of CNS type and percentage were investigated in terms of morphological, thermal, mechanical, and dielectrical properties. Composite morphological analysis reveals a good dispersion of CNS, at low and high content. Thermal properties underline the nucleation effect of CNS on PCL polymer matrix. Reinforcing effects in terms of increased tensile modulus were obtained with both nanofillers, but a higher reduction of the ductility was shown in PCL/CNF materials. A higher efficiency to form a conductive network, assessed by AC conductivity, was observed for SWCNTs at concentration lower than 1 wt. % © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

4,4′‐Bismaleimidodiphenyl methane modified novolak resin/titania nanocomposites: Preparation and properties

4,4′‐Bismaleimidodiphenyl methane modified novolak resin/titania nanocomposites were prepared by the sol–gel process of tetrabutyl titanate in the presence of 4,4′‐bismaleimidodiphenyl methane modified novolak resin prepolymers with acetyl acetone as a stabilizer. These nanocomposite materials were characterized by Fourier transform infrared analysis, dynamical mechanical analysis, thermogravimetric analysis, transmission electron microscopy, and field emission scanning electron microscopy. Nanometer titania particles were formed in the novolak resin matrix, and the average original particle size of the dispersed phase in the nanocomposites was less than 150 nm, but particle aggregates of larger size existed. The introduction of the titania inorganic phase with a nanoscale domain size did not improve the glass‐transition temperature of the nanocomposites but lowered the thermal resistance of the material because of the incomplete removal of acetyl acetone coordinated with tetrabutyl titanate, and it improved the modulus of the material at lower temperatures (<200°C) but lowered the modulus at higher temperatures (>250°C). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 52–57, 2006     

Preparation and properties of poly(dimethyl siloxane)–colloidal silica/functionalized colloidal silica nanocomposites

Aqueous spherical colloidal silica (CS) particles with a diameter of 15 ± 5 nm were modified with three different types of monofunctional silane coupling agents to prepare functionalized colloidal silica (FCS) particles. The effects of the surface chemistry of the FCS were studied as a function of the CS/FCS loading in the poly(dimethyl siloxane) (PDMS) polymer. The prepared PDMS–CS/FCS composites were investigated for their physical properties both in the cured and uncured states. The extent of filler–filler and filler–polymer interactions was found to vary with the type of functionalizing agent used to treat the surface of the CS. The filler–filler interaction appeared to be predominant in the PDMS–CS composites, and improved filler–polymer interaction was indicated in the case of the PDMS–FCS composites. The composites containing CS treated with methyltrimethoxysilane exhibited relatively better optical and mechanical properties compared to the other PDMS–FCS composites. This study highlighted the importance of judiciously choosing functionalizing agents to achieve PDMS–FCS composites with predetermined optical and mechanical properties. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of graphene/poly(vinyl alcohol) nanocomposites

Graphene (GE)‐based nanocomposites are emerging as a new class of materials that hold promise for many applications. In this article, we present a general approach for the preparation of GE/poly(vinyl alcohol) (PVA) nanocomposites. The basic strategy involved the preparation of graphite oxide from graphite, complete exfoliation of graphite oxide into graphene oxide sheets, followed by reduction to GE nanosheets, and finally, the preparation of the GE/PVA nanocomposites by a simple solution‐mixing method. The synthesized products were characterized by X‐ray diffraction, field emission scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetry, and differential scanning calorimetry analysis. The GE nanosheets were well dispersed in the PVA matrix, and the restacking of the GE sheets was effectively prevented. Because of the strong interfacial interaction between PVA and GE, which mainly resulted from the hydrogen‐bond interaction, together with the improvement in the PVA crystallinity, the mechanical properties and thermal stability of the nanocomposites were obviously improved. The tensile strength was increased from 23 MPa for PVA to 49.5 MPa for the nanocomposite with a 3.25 wt % GE loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of organoclay chemistry and morphology on properties of poly(lactic acid) nanocomposites

Poly(lactic acid) (PLA) nanocomposites with different layered organoclays (variation in the surface treatment of silicate) and one special nanofiller (mixed mineral thixotrope) were melt-compounded using a semi-industrial co-rotating twin-screw extruder. Effects of the silicate surface treatment and shape on the structure as well on processing and utility properties in PLA matrix were investigated. The structural changes in polymer matrix were evaluated from dynamic experiments in the shear flow using low-amplitude oscillatory measurements. Moreover, new approach for morphological investigation of nanocomposites using small-angle X-ray scattering was presented. Concerning utility properties, tests of mechanical and barrier properties were performed to compare enhancement of PLA matrix due to incorporation of different nanoparticles. Surprisingly, filling the PLA matrix with mixed mineral thixotrope resulted into very high material performance (in particular, significant improvement in barrier properties) compared to filling with commercial layered silicates. In this way, new type of nanofiller for PLA applications has been successfully tested.     

Morphology and mechanical properties of polymer nanocomposites with a poly(hydroxy ether of bisphenol A) matrix

The poly(hydroxy ether of bisphenol A) (phenoxy (Ph)) has been revealed as a polymeric matrix able to intercalate in, and partially exfoliate a commercial organically modified montmorillonite. Dispersion was attributed to chemical interactions between the Ph and the inorganic clay. A significant increase in the modulus of elasticity (33% with 3.8% montmorillonite (MMT) addition) was observed, together with an unusual increase in ductility attributed to surfactant migration, that should allow tailoring of the processing conditions to widen exfoliation. Ph‐based nanocomposites could be used as a nanostructured masterbatch for producing new polymer nanocomposites by mixing the masterbatch with the polymeric matrices that either miscibilize or are compatible with Ph. Copyright © 2006 Society of Chemical Industry     

Preparation of graphene/poly(vinyl alcohol) nanocomposites with enhanced mechanical properties and water resistance

The control and dispersal of graphene nanosheets in polymer hosts are challenges in the development of high‐performance graphene‐based nanocomposites due to the strong interlayer cohesive energy and surface inertia. Here we report a simple and practical approach to synthesize graphene‐reinforced poly(vinyl alcohol) (PVA) composite films by incorporating graphene oxide and graphene into PVA aqueous solution. The resulting nanocomposites revealed increases of up to 212% in tensile strength and 34% in elongation at break with only 0.5 wt% graphene content. Water absorption measurements showed that the water absorption ratio of the graphene/PVA composites decreased from 105.2 to 48.8%, and the barrier properties were obviously improved. Contact angle measurements showed that the composites were hydrophobic (θ > 90°) in contrast to the highly hydrophilic (θ < 90°) pure PVA. Copyright © 2011 Society of Chemical Industry