Largely restricted nucleation effect of carbon nanotubes in a miscible poly(vinylidene fluoride)/poly(butylene succinate) blend

The crystallization behaviors of miscible poly(vinylidene fluoride)/poly(butylene succinate) (PVDF/PBS) and its blend composites with carbon nanotubes (CNTs) during non‐isothermal and isothermal processes were investigated. The results showed that CNTs acted as heterogeneous nucleation agents and further improved the nucleation ability of PBS and PVDF in blends. However, compared with the nucleation effects of CNTs in PBS/CNT or PVDF/CNT binary composites, the nucleation effect of CNTs in miscible PVDF/PBS was largely restricted and nucleation efficiency was lowered. A reasonable explanation about the restricted nucleation ability of CNTs was studied from the viewpoint of interfacial interactions between polymer components and CNTs, in which a preferential affinity of CNTs to PBS was found. Further combined with the preparation method, it is proposed that PVDF chains adsorbed on the CNT surface in the master batch were peeled off from the CNTs by incorporated PBS chains, due to the better interaction between PBS and CNTs. Finally, the PVDF chains at the interface were diluted by PBS, and most of the CNT surface was covered by PBS chains, giving rise to the nucleation of PBS on the CNTs. On the other hand, unremoved PVDF still adsorbed on the CNT surface and crystallized. Compared with PVDF/CNT and PBS/CNT binary composites, the nucleation density in the ternary composites was greatly lowered, resulting in restricted nucleation effects of CNTs. On the other hand, the preferable adsorption of PBS on CNTs induced an apparent phase fluctuation in the PVDF/PBS blend composites, which also reflected the selective adsorption of PBS on the CNT surface. © 2016 Society of Chemical Industry     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Effect of diluents on the crystallization behavior of poly(4‐methyl‐1‐pentene) and membrane morphology via thermally induced phase separation

The effect of diluents on polymer crystallization and membrane morphology via thermally induced phase separation(TIPS) were studied by changing the composition of the mixed‐diluents systematically, in the system of poly(4‐methyl‐1‐pentene) (TPX)/dibutyl‐phthalate (DBP)/di‐n‐octyl‐phthalate (D‐n‐OP) with TPX concentration of 30 wt %. The TPX crystallization was observed with differential scanning calorimetry (DSC) and wide angle X‐ray diffraction (WAXD). The membranes were characterized with scanning electron microscopy (SEM), porosity, and pore size measurement. As the content of D‐n‐OP increased in mixed‐diluents, the solubility with TPX increased, inducing the phase separation changing from liquid–liquid phase separation into solid–liquid phase separation, which changed the membrane morphology and structure. When the ratios of DBP to D‐n‐OP were 10 : 0, 7 : 3; 5 : 5, and 3 : 7, membranes were formed with cellular structure and well connected pores, while the ratio was 0 : 10, discernable spherulities were found with not well‐formed pore structure. The effect of composition of the mixed‐diluents on membrane morphology was more remarkable in TPX/dioctyl‐sebacate (DOS)/dimethyl‐phthalate (DMP) system, since good cellular structure was formed when the ratios of DOS to DMP were 10 : 0, 7 : 3, while spherulites were observed when 5 : 5. Dual endotherm peaks behavior on DSC melting curves emerged for all the samples in this study, which was attributed to the special polymer crystallization behavior, primary crystallization, and secondary crystallization occurred when quenching the samples. As the content of D‐n‐OP increased, the secondary crystallization enhanced which induced the first endotherm peak on DSC melting curves moving to a lower temperature and the broadening of the overall melting peak, as well as the increasing of the overall crystallinity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nonisothermal crystallization kinetics of poly(vinylidene fluoride) in a poly(vinylidene fluoride)/dibutyl phthalate/di(2‐ethylhexyl)phthalate system via thermally induced phase separation

The nonisothermal crystallization kinetics of poly(vinylidene fluoride) (PVDF) in PVDF/dibutyl phthalate (DBP)/di(2‐ethylhexyl)phthalate (DEHP) blends via thermally induced phase separation were investigated through differential scanning calorimetry measurements. The Ozawa approach failed to describe the crystallization behavior of PVDF in PVDF/DBP/DEHP blends, whereas the modified Avrami equation successfully described the nonisothermal crystallization process of PVDF. Two stages of crystallization were observed in this analysis, including primary crystallization and secondary crystallization. The influence of the cooling rate and DBP ratio in the diluent mixture on the crystallization mechanism and crystal structure was determined by this method. The Mo approach well explained the kinetics of primary crystallization. An analysis of these two methods indicated that the increase in the DBP ratio in the diluent mixture caused a decrease in the crystallization rate at the primary crystallization stage. The activation energy was determined according to the Kissinger method and also decreased with the DBP ratio in the diluent mixture increasing. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Formation of an interconnected lamellar structure in PVDF membranes with nanoparticles addition via solid‐liquid thermally induced phase separation

Novel microporous membranes were prepared via thermally induced solid‐liquid (S‐L) phase separation of mixtures containing poly(vinylidene fluoride) (PVDF)/diphenyl ketone (DPK)/nanoparticles [such as montmorillonite (MMT) and polytetrafluoroethylene (PTFE)] in diluted systems with a mass ratio of 29.7/70/0.3 wt %. The crystallization and melting characteristics of these diluted systems were investigated by polarizing optical microscopy (POM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and wide angle X‐ray diffraction (WAXD). The nanoparticle structure and the interaction between PVDF chains and nanoparticle surfaces determined the crystallization behavior and morphology of the PVDF membrane. The addition of MMT and PTFE had a significant nucleation enhancement on the crystallization of PVDF accompanied by S‐L phase separation during the thermally induced phase separation (TIPS) process. It was observed that an interconnected lamellar structure was formed in these two membranes, leading to a higher tensile strength compared with that of the reference membrane without nanoparticles addition. Additionally, addition of MMT facilitates the fiber‐like β phase crystal formation, resulting in the highest elongation at break. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Shape stability enhancement of PVDF electrospun polymer electrolyte membranes blended with poly(2-acrylamido-2-methylpropanesulfonic acid lithium)

The purpose of this study is to overcome the poor dimensional stability of poly(vinylidene fluoride) (PVDF)-based electrospun membranes for polymer electrolytes, a new type of composite fibrous membranes based on PVDF/poly(2-acrylamido-2-methylpropanesulfonic acid lithium) (PAMPSLi) blend systems with different blend ratios were fabricated by electrospinning method. Morphology of the composite fibrous membranes was evaluated by scanning electron microscopy. Average diameters of the membranes were less than 250 nm, which were far less than that of pure PVDF fibrous membrane (400 nm). Fourier transform infrared spectroscopy and Raman scattering were used to characterize the interactions of two polymers. Wide-angle X-ray diffraction and differential scanning calorimetry techniques were applied to investigate the crystal structure of composite fibrous membranes. Owning to the good miscibility between PVDF and PAMPSLi, no phase-separated microstructure was observed in composite fibrous membranes. The membranes possessed a good wettability by liquid electrolytes and exhibited an excellent dimensional stability even at high loading of electrolytes. The polymer electrolyte showed the ionic conductivity of 3.45 × 10^?3 S/cm at room temperature and electrochemical stability up to 5.4 V for the blend ratio of 5/1. PVDF/PAMPSLi (5/1)-based polymer electrolyte was observed much more suitable than polymer electrolytes with other ratios of PVDF/PAMPSLi for application in high-performance lithium rechargeable batteries.     

An investigation of the blend of partially brominated poly(2,6-dimethyl 1,4-phenylene oxide) and polystyrene in the primary (glass-to-rubber) transition region

Compatible polymer blends can be used to test critically the viability of the damped Debye lattice (DDL) model of relaxation in the primary (glass-to-rubber) transition region. Since these blends form because of specific intermolecular interaction, the force constants that characterize intermolecular elastic interactions can be controlled to some extent by varying blend composition. The model predicts an unusual sharpening of the stress relaxation master curve of a marginally two-dimensional DDL upon dilution with a plasticizer. We have prepared an appropriate two-dimensional DDL by adding modest amounts of partially brominated poly(2,6-dimethyl 1,4-phenylene oxide) to polystyrene to form compatible blends. As predicted by the model, sharpening of the stress relaxation behavior upon dilution was observed for all blend compositions and for all diluents used. However, at higher brominated poly(phenylene oxide) concentrations, the anticipated diluent concentration dependence was not always observed and the sharpening of the stress relaxation behavior was less than expected. In similar experiments carried out on diluted homopolymers, the relative values of the solubility parameters of the polymers and the diluents strongly influenced the effectiveness of the diluent in changing the stress relaxation behavior. In this blend system, the particular chemical nature of the diluent was found to be much less important; in fact, the three diluents used all evoked approximately the same behavior despite their having solubility parameters that differed significantly.     

Investigation on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends by solution casting

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by solution casting. The crystallization behavior and hydrophilicity of ternary blends were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and contact angle test. According to morphological analysis, the surface was full of typical spherulitic structure of PVDF and the average diameter was in the order of 3 μm. The samples presented predominantly β phase of PVDF by solution casting. It indicated that the size of surface spherulites and crystalline phase had little change with the PMMA or PVP addition. Moreover, FTIR demonstrated special interactions among the ternary polymers, which led to the shift of the carbonyl stretching absorption band of PVP. On the other hand, the melting, crystallization temperature, and crystallinity of the blends had a little change compared with the neat PVDF in the first heating process. Except for the content of PVP containing 30 wt %, the crystallinity of PVDF decreased remarkably from 64% to 33% and the value of t_1/2 was not obtained. Besides, the hydrophilicity of PVDF was remarkably improved by blending with PMMA/PVP, especially when the content of PVP reached 30 wt %, the water contact angle displayed the lowest value which decreased from 98.8° to 51.0°. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrospun fiber membranes from blends of poly(vinylidene fluoride) with fouling‐resistant zwitterionic copolymers

Nonwoven super‐hydrophobic fiber membranes have potential applications in oil–water separation and membrane distillation, but fouling negatively impacts both applications. Membranes were prepared from blends comprising poly(vinylidene fluoride) (PVDF) and random zwitterionic copolymers of poly(methyl methacrylate) (PMMA) with sulfobetaine methacrylate (SBMA) or with sulfobetaine‐2‐vinylpyridine (SB2VP). PVDF imparts mechanical strength to the membrane, while the copolymers enhance fouling resistance. Blend composition was varied by controlling the PVDF‐to‐copolymer ratio. Nonwoven fiber membranes were obtained by electrospinning solutions of PVDF and the copolymers in a mixed solvent of N,N‐dimethylacetamide and acetone. The PVDF crystal phases and crystallinities of the blends were studied using wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). PVDF crystallized preferentially into its polar β‐phase, though its degree of crystallinity was reduced with increased addition of the random copolymers. Thermogravimetry (TG) showed that the degradation temperatures varied systematically with blend composition. PVDF blends with either copolymer showed significant increase of fouling resistance. Membranes prepared from blends containing 10% P(MMA‐ran‐SB2VP) had the highest fouling resistance, with a fivefold decrease in protein adsorption on the surface, compared to homopolymer PVDF. They also exhibited higher pure water flux, and better oil removal in oil–water separation experiments. © 2018 Society of Chemical Industry     

Investigation of the structural,thermal, mechanical,and optical properties of poly(methyl methacrylate) and poly(vinylidene fluoride) blends

In this investigation, poly(methyl methacrylate) (PMMA) and poly(vinylidene fluoride) (PVDF) blends (w/w) were prepared in a Brabender (South Hackensack, NJ) plasticorder with a thermoplastic mixing chamber (type W60) preheated at 180°C. These blends were further converted into films by a conventional solution casting method and characterized with Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction, mechanical property measurements, impact strength testing, ultraviolet–visible spectroscopy, refractive‐index measurements, and contact‐angle study. The Fourier transform infrared results indicated that the compatibility between these two systems resulted from hydrogen bonding between the carbonyl group of PMMA and the CH₂ group of PVDF. The thermal analysis showed depressions in the glass‐transition temperature, melting temperature, and crystallization temperature. The heat of crystallization increased with an increase in the PVDF content in the blend. An increase in the heat of crystallization meant an increase in the crystallinity. An increase in the cooling rate increased the crystallization rate. The improvement in the mechanical properties of the blend films indicated that the observed behavior was ascribable to a more coherent structure of the blends due to strong specific interactions between PMMA and PVDF chains. The impact strength analysis revealed a substantial increase in the impact strength from 21.64 to 38.52 J/m. Optical absorption spectra suggested the presence of an optical band gap energy that increased with an increase in the PVDF content in the blend. The contact angle against water increased with the PVDF content in the blend film, and this was caused by the hydrophobicity of PVDF due to the CF₂ group of PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Amphiphilic ABA‐type triblock copolymers for the development of high‐performance poly(vinylidene fluoride)/poly(vinyl pyrrolidone) blend ultrafiltration membranes for oil separation

ABA‐type amphiphilic triblock copolymers (TBCs) were synthesized by a reversible addition fragmentation chain transfer (RAFT) process with a telechelic polystyrene macro‐RAFT agent and 4‐[n‐(acryloyloxy)alkyloxy]benzoic acid monomers. Ultrafiltration (UF) membranes were fabricated by a phase‐inversion process with blends of the TBC, poly(vinylidene fluoride) (PVDF), and poly(vinyl pyrrolidone) (PVP) in dimethylformamide. The UF‐fabricated membranes were characterized by scanning electron microscopy, atomic force microscopy, water contact angle measurement, thermogravimetric analysis, and differential scanning calorimetry. Pure water permeation, molecular weight cutoff values obtained by the permeation of different molecular weight polymers as probe solutes, bovine serum albumin (BSA) solution permeate flux, and oil–water emulsion filtration tests were used to evaluate the separation characteristics of the fabricated membranes. The tripolymer blend membranes exhibited a higher flux recovery ratio (FRR) after the membrane was washed with sodium lauryl sulfate (0.05 wt %) solution for a BSA solution (FRR = 88%) and oil–water emulsion (FRR = 95%) feeds when than the PVDF–PVP blend membrane (57 and 80% FRR values for the BSA solution and oil–water emulsion, respectively). The pendant carboxylic acid functional moieties in this ABA‐type TBC have potential advantages in the fabrication of high‐performance membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45132.     

Peculiar crystallization kinetics of biodegradable poly(lactic acid)/poly(propylene carbonate) blends

Binary blends of poly(lactic acid) (PLA) and poly(propylene carbonate) (PPC) were found to display a peculiar crystallization kinetics. The two biodegradable polymers were blended by melt mixing, to obtain binary blends at various compositions. Temperature‐modulated calorimetry and dynamic‐mechanical analysis indicated that the blend components are partially miscible, and display two separate glass transitions, at temperatures intermediate to those of the plain polymers. Electron microscopy analysis disclosed the morphology of PLA/PPC blends, made of PPC‐rich particles finely dispersed within the PLA‐rich matrix. The possible establishment of interactions between the functional groups of the two polymers upon melt mixing has been hypothesized as the reason for partial miscibility and compatibility of the two biodegradable polymers. The PLA/PPC blends display good mechanical properties, with enhanced performance at rupture compared with plain PLA. Most importantly, the addition of PPC affects also the crystallization kinetics of PLA, since the more mobile PPC chains favor diffusion of the stiffer PLA chain segments towards the growing crystals, which fastens the spherulite growth rate of PLA. Such positive influence of an amorphous polymer on crystal growth rate has been demonstrated here for the first time in blends that display phase‐separation in the melt. POLYM. ENG. SCI., 55:2698–2705, 2015. © 2015 Society of Plastics Engineers     

Preparation of a porous structure in a poly(4‐methyl‐1‐pentene)/diphenyl ether system with a thermally induced phase‐separation method

Poly(4‐methyl‐1‐pentene) was used to prepare porous structures by a thermally induced phase‐separation method. Different porous structures were obtained with poly(4‐methyl‐1‐pentene), which has excellent properties as a polymer, and diphenyl ether as a diluent. The affecting factors, including the polymer concentration and cooling temperature, are discussed. Scanning electron microscopy images and porosity values were obtained to investigate the affecting factors. According to the cloud‐point temperature and crystallization temperature, a phase diagram was also obtained to explain the phase‐separation process. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Casting solvent effect on crystallization behavior and morphology of poly(ethylene oxide)/poly(methyl methacrylate)

Poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) blends were prepared by casting from either chloroform or benzene solvents. After casting from solvents, all samples used in this study were preheated to 100°C and held for 10 min. Then, the solvent effect on the crystallization behavior and thermodynamic properties were studied by differential scanning calorimeter (DSC). Also, the morphology of spherulite of casting film was studied by polarized optical microscope. From the DSC and polarizing optical microscopy (POM) results, it was found that PEO/PMMA was miscible in the molten state no matter which casting solvent was used. However, the crystallization of PEO in the chloroform‐cast blend was more easily suppressed than it was in the benzene‐cast blend. Relatively, the chloroform‐cast blend showed the greater melting‐point depressing of PEO crystals. Also, the spherulite of chloroform‐cast film showed a coarser birefringence. It was supposed that the chloroform‐cast blend had more homogeneous morphology. It is fair to say that polymer blends, cast from solvent, are not necessarily in equilibrium. However, the benzene‐cast blends still were not in equilibrium even after preheating at 100°C for 10 min. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1627–1636, 2000     

Electrospun poly(vinylidene‐fluoride)/POSS nanofiber membrane‐based polymer electrolytes for lithium ion batteries

In this study, poly(vinylidene fluoride) (PVDF)/polyhedral oligomeric silsesquioxanes (POSS) nanofibrous membranes are prepared through electrospun process. Field emission scanning electron microscope images clearly show that PVDF/POSS membranes have interconnected multi fibrous layers with ultrafine porous structures. The average fiber diameter and crystallinity of PVDF/POSS membranes are lesser than that of pure PVDF membrane. Thermal stability and electrolyte uptake of blend membranes increase with increasing POSS content. Finally, PVDF/POSS membranes are soaked in a liquid electrolyte to form the polymer electrolytes and are assembled in coin cells to test their electrochemical properties such as ionic conductivity, interfacial characteristics, and electrochemical stability windows. The ionic conductivity improves with increasing POSS content and the highest ionic conductivity reaches 2.91 × 10⁻³ S/cm at room temperature. It is also worth mention that the composite polymer electrolytes show low interfacial resistance and high electrochemical stability window of 5.6 V (vs. Li⁺ /Li) with storage time. POLYM. COMPOS., 38:629–636, 2017. © 2015 Society of Plastics Engineers     

Morphology development and crystallization behavior of a poly(ethylene terephthalate)/polycarbonate blend

The morphology development and crystallization behavior of an extruded poly(ethylene terephthalate)/polycarbonate blend were studied with optical microscopy, light scattering, and differential scanning calorimetry (DSC). During annealing at 280°C, liquid–liquid phase separation via spinodal decomposition proceeded in a melt‐extruded specimen. After the formation of the domain structure, the blend slowly underwent phase homogenization by transesterification between the two polymers. The specimen, annealed for various times (t_s's) at 280°C, was subjected to a temperature drop to 180°C for the isothermal crystallization, and then the effects of liquid‐phase changes on crystallization were investigated. The crystal growth rate decreased with t_s. The slow crystallization with a large t_s value was associated with the composition change of the separated phases and the change of the sequence distribution in the polymer chains during annealing. The influence of t_s on the endothermic behavior of the samples was examined. As t_s increased, the recrystallization rate was retarded during the DSC scan, displaying multiendothermic behavior. The DSC data also suggested that the increased level of transesterification would give rise to a higher number of species being rejected from the primary crystals, leading to enhanced secondary crystallization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Nanoscale localization of poly(vinylidene fluoride) in the lamellae of thin films of symmetric polystyrene-poly(methyl methacrylate) diblock copolymers

We employed thin film blends of diblock copolymers with functional homopolymers as a simple strategy to incorporate organic functional materials into nanodomains of diblock copolymers without serious synthesis. A blend pair of polystyrene-poly(methyl methacrylate) (PS-PMMA) diblock copolymers and poly(vinylidene fluoride) (PVDF) was selected as a model demonstration because PVDF is a well-known ferroelectric polymer and completely miscible with amorphous PMMA. Thin films of symmetric PS-PMMA copolymers provided the nanometer-sized PMMA lamellae, macroscopically parallel to the substrate, in which PVDF chains were dissolved. Thus, amorphous PVDF chains were effectively confined in the PMMA lamellae of thin film blends. The location of PVDF chains in the PMMA lamellae was investigated by the dependence of the lamellar period on the volume fraction of PVDF, from which we found that PVDF chains were localized in the middle of the PMMA lamellae. After the crystallization of PVDF, however, some of PVDF migrated to the surface of the film and formed small crystallites.     

Phase behavior of poly(ε-caprolactone)/ poly (vinylidene fluoride) blends

The miscibility of blends of poly (ε-caprolactone) (PCL)/poly(vinylidene fluoride) (PVDF) was studied by measuring the cloud point, melting point depression and crystallization kinetics. Lower critical solution temperature (LCST) behavior was observed at PCL-rich compositions, whilst it was not observed at high compositions of PVDF. However it is possible that an LCST could exist below the melting point of PVDF. From analysis of the melting point depression, the Flory interaction parameter x₁₂, was calculated from the Nishi-Wang equation and the value was found to be-1.5. The crystallization rate of PCL increased with increasing amount of PVDF in the blend. The spinodal curve for PCL/PVDF blends was simulated by using the lattice-fluid theory.     

Fabrication of poly(vinylidene fluoride) membrane via thermally induced phase separation using ionic liquid as green diluent

Ionic liquid(IL), 1-butyl-3-methylimidazolium hexafluorophosphate([BMIM]PF6) as a new and environmentally friendly diluent was introduced to prepare poly(vinylidene fluoride)(PVDF) membranes via thermally induced phase separation(TIPS). Phase diagram of PVDF/[BMIM]PF6 was measured. The effects of polymer concentration and quenching temperature on the morphologies, properties, and performances of the PVDF membranes were investigated. When the polymer concentration was 15 wt%, the pure water flux of the fabricated membrane was up to nearly 2000 L·m~(-2)·h~(-1), along with adequate mechanical strength. With the increasing of PVDF concentration and quenching temperature, mean pore size and water permeability of the membrane decreased. SEM results showed that PVDF membranes manufactured by ionic liquid(BMIm PF6) presented spherulite structure. And the PVDF membranes were represented as β phase by XRD and FTIR characterization. It provides a new way to prepare PVDF membranes with piezoelectric properties.     

Interrelationship of thermal and mechanical properties of poly(ethylene terephthalate)/poly(ethylene 2,6‐naphthalate)/graphene nanocomposites

In the present work, attempts were made to investigate the thermal and mechanical properties of melt‐processed poly(ethylene terephthalate) (PET)/poly(ethylene 2,6‐naphthalate) (PEN) blends and its nanocomposites containing graphene by using differential scanning calorimetry and tensile test experimenting. The results showed that crystallinity, which depends on a blend ratio, completely disappeared in a composition of 50/50. By introducing graphene to PET, even in low concentrations, the crystallinity of samples increased, while the nanocomposite of PEN indicated reverse behavior, and the crystallinity was reduced by adding graphene. In the case of PET‐rich (75/25) nanocomposite blends, by increasing the nano content in the blend, the crystallinity of the samples was enhanced. This behavior was attributed to the nucleating effect of graphene particles in the samples. From the results of mechanical experiments, it was found in PET‐rich blends that by increasing the PEN/PET ratio, the modulus of samples decreased, whereas in the case of PEN‐rich blends, a slight increment of modulus is seen as a result of the increment of the PEN/PET ratio. The two contradicting behaviors were attributed to the reduction of crystallinity of PET‐rich blends by enhancement of PEN/PET ratio and the rigid structure of PEN chains in PEN‐rich blends. Unlike the different modulus change of PET‐rich and PEN‐rich blends, the nanocomposites of these blends similarly indicated an increment of modulus and characteristics of rigid materials by increasing the nano content. Furthermore, the same behavior was detected in nanocomposites of each polymer (PET and PEN nanocomposites). The alteration from ductile to rigid conduction was related to the impedance in the role of graphene plates against the flexibility of polymer chains and high values of graphene modulus. J. VINYL ADDIT. TECHNOL., 23:210–218, 2017. © 2015 Society of Plastics Engineers