空速和二氧化碳对沼气脱硫剂硫容确定的影响

为了弄清空速与二氧化碳含量对氧化铁脱硫剂硫容确定的影响,分别在实验气源为纯硫化氢,空速为40、80、120和160 h-1以及实验气源为二氧化碳含量分别在0%、20%、40%和80%,其余为硫化氢,空速为80 h-1条件下,对T502(粗脱硫剂)和HXT-2(精脱硫剂)2种氧化铁脱硫剂进行了不同测试条件对氧化铁硫容确定影响的研究。研究结果表明,T502和HXT-2氧化铁脱硫剂硫容测试结果随着空速和二氧化碳含量增加而减少,结果显示了在空速较低条件下(120h-1),二氧化碳含量在40%以下时对氧化铁脱硫剂硫容测试结果影响不大,但二氧化碳含量在40%以上时,对氧化铁脱硫剂硫容测试结果影响显著。     

新型柱状核桃壳活性炭脱硫动力学

采用以农业废弃物核桃壳为原料,天然软锰矿为添加剂共混制成的新型柱状活性炭进行了不同水蒸气含量下的烟气脱硫实验,利用Bangham和Elovich 2种模型对实验结果进行模拟与比较。实验结果表明,随着水蒸气含量的增加,穿透硫容和时间逐渐增加,并在水蒸气含量为10%时达到最大点,此时硫容为243.0 mg/g。模拟结果表明,2种模型均可以较好地模拟烟气脱硫实验结果,其中Elovich模型具有更高的拟合相关度和准确性。在对Elovich模型加以改进以包含水蒸气影响后,可以更好地描述烟气在不同水蒸气含量下的新型柱状活性炭脱硫情况。     

活性焦表面性质对CUO/AC脱硫性能的影响

分别以不同浓度的硝酸处理活性焦载体,采用硝酸铜溶液浸渍法制备CuO/AC催化剂,利用BET、FT-IR和XRD等方法对载体及催化剂进行表征.考察了不同浓度的硝酸处理对活性焦载体性质的影响,并对制得的催化剂的脱硫性能进行了比较.结果表明,活性焦经过硝酸处理后孔结构参数变化很小,而表面含氧酸性官能团的含量有了很大的提高,使...     

Effect of potassium hydroxide activation in the desulfurization process of activated carbon prepared by sewage sludge and corn straw

Series sludge straw–based activated carbons were prepared by sewage sludge and corn straw with potassium hydroxide (KOH) activation, and the desulfurization performance of activated carbons was studied. To obtain the best desulfurization performance, the optimum ratio between the raw materials and the activator was investigated. The results showed that when the mass ratio of sewage sludge, corn straw, and KOH was 3:7:2, the activated carbon obtained the best breakthrough and saturation sulfur sorption capacities, which were 12.38 and 5.74 times, respectively, those of samples prepared by the nonactivated raw materials. The appropriate KOH could improve the microporosity and alkaline groups, meanwhile reducing the lactone groups, which were all beneficial to desulfurization performance. The chemical adsorption process of desulfurization can be simplified to four main steps, and the main desulfurization products are elemental sulfur and sulfate.

Implications: Sewage sludge (SS) and corn straw (CS) both have great production and wide distribution and are readily available in China. Much attention has been paid on how to deal with them effectively. Based on the environment protection idea of waste treatment with waste and resource recycling, low-cost adsorbents were prepared by these processes. The proposed method can be expanded to the municipal solid waste recycling programs and renewable energy plan. Thus, proceeding with the study of preparing activated carbon by SS and straw as a carbon-based dry desulfurization agent could obtain huge social, economic, and environmental benefits.     

活性炭纤维生物挂膜脱除硫化氢

生物脱硫法作为一种高效、高实用性的除硫新技术而受到越来越多的关注。以活性炭纤维为微生物载体,通过活性污泥上清液挂膜驯化,考察硫化氢进气量、喷淋量、pH值和硫酸根离子浓度等条件对脱硫效率的影响。研究结果表明,在室温下,硫化氢负荷为90 g/(m3.h),进气浓度控制在3 g/m3,进气量为60 L/h,喷淋量为250～650 L/(m3.d),pH为2～5的条件下,生物活性炭纤维对硫化氢的去除率可保持在98%以上。     

Effect of SME biodiesel blends on PM2.5 emission from a heavy-duty engine

To explore the effect of biodiesel and sulfur content on PM_2.5 emissions, engine dynamometer tests were performed on a Euro II engine to compare the PM_2.5 emissions from four fuels: two petroleum diesel fuels with sulfur contents of 50 and 100 ppm respectively, and two B20 fuels in which soy methyl ester (SME) biodiesel was added to each of the above mentioned petroleum diesel fuels (v/v: 80%/20% for petroleum diesel and SME respectively). Gaseous pollutants and PM_2.5 emissions were sampled with an AVL AMA4000 and Model 130 High-Flow Impactor (MSP Corp). Measurements were made of the PM_2.5 mass, organic carbon (OC), elemental carbon (EC) and the water-soluble ion distribution. The results showed that PM_2.5 emissions decreased with lower sulfur content or blending with SME biodiesel, and the decrease would be more by applying both two methods together. Particles of approximately 0.13 μm contributed 48–83% of PM_2.5 emissions. The impact of sulfur content on this percentage was different for low and high engine speed. The majority of PM_2.5 was comprised of OC and EC, and the carbon emission rate had the same trend as PM_2.5. Since the EC abatement of B20 was larger than OC, the OC/EC ratio of B20 was always larger than that of petroleum diesel. For petroleum diesel, the OC/EC increased with sulfur content, which was not the case for B20. The SO₄^2? had highest emission rate in the water-soluble ions of PM.     

Long-term evaluation of activated carbon as an adsorbent for biogas desulfurization

ABSTRACT

In this study, granular activated carbon (GAC) was used as an adsorbent for biogas desulfurization. Biogas containing 932–2,350 ppm of H₂S was collected from an anaerobic digester to treat the wastewater from a dairy farm with about 200 cows. An adsorption test was performed by introducing the biogas to a column that was packed with approximately 50 L of commercial GAC. The operation ceased if the effluent gas had an H₂S concentration of over 100 ppm. The GAC was replaced by a given weight of new GAC in a subsequent test. According to the results, for H₂S concentrations in the range of 932–1,560 ppm (average±SD = 1,260 ± 256 ppm), 1 kg of the GAC yielded biogas treatment capacities of 568 ± 112 m³ and H₂S adsorption capacities of 979 ± 235 g. For the higher influent H₂S concentrations of 2,110 ± 219 ppm, the biogas treatment and H₂S-adsorption capacities decreased to 229 ± 18 m³ and 668 ± 47 g, respectively. An estimation indicated a requisite cost of US$16.5 for the purification of 1,000 m³ of biogas containing 2,110 ppm of H₂S. This cost is approximately 5% of US$330, the value of 1,000 m³ of biogas.     

Application of High Gradient Magnetic Separation to Fine Particle Control

The char produced in the thermolysis of granulated scrap tyres has few market outlets, reducing the economic viability of the thermolytic process. This paper reports the potential of this char as a low-cost precursor of porous carbons. The tyre-derived char was demineralized in either alkaline or acidic media to reduce its ash, zinc, sulfur, and silica contents. The lowest impurity content was achieved with an HNO₃/H₂O treatment. The resulting demineralized char was then subjected to activation by KOH or CO₂. The Brunauer-Emmett-Teller (BET)-specific surface area of the activated carbon produced by the KOH treatment was 242 m²/g, whereas that of the CO₂-activated carbon was 720 m²/g. The textural properties of the latter product were similar to those of some commercial activated carbons. The use of tyre-derived char as a precursor of porous carbons could render the thermolytic treatment of scrap tyres more economically attractive.

Implications: Char produced in thermolysis of granulated scrap tyres has a few market outlets; in this paper an alternative for its use is presented. The char was converted into activated carbon with textural properties similar to those of some commercial activated carbons. This process could render the thermolytic treatment of scrap tyres more economically attractive.     

MnO2对煤粉中CaO固硫效率影响机理

采用热力学计算和实验方法对钙硫比n（CaO）/n（S）=2.0条件下不同钙基固硫剂的固硫效果进行了比较,发现：CaO的固硫效率最高。以CaO为固硫剂,研究了添加剂MnO2对CaO固硫效果的影响。结果表明,加入MnO2可以提高CaO的固硫效率,且其含量为1%时对CaO固硫的促进效果最佳。这是因为煤粉燃烧过程中MnO2将逐级分解,分解产物依次为Mn2O3和Mn3O4,锰的氧化物一方面可以催化CaO的固硫反应,另一方面,Mn3O4本身也参与到固硫反应之中,生成MnSO4,从而促进钙基固硫剂的固硫效果。     

From Air Repair to EM: A&WMA’s Publications through a Century of Change

Abstract

This paper analyzes the natural desulfurization process taking place in coal-fired units using Greek lignite. The dry scrubbing capability of Greek lignite appears to be extremely high under special conditions, which can make it possible for the units to operate within the legislative limits of sulfur dioxide (SO₂) emissions. According to this study on several lignite-fired power stations in northern Greece, it was found that sulfur oxide emissions depend on coal rank, sulfur content, and calorific value. On the other hand, SO₂ emission is inversely proportional to the parameter y _CO2max, which is equal to the maximum carbon dioxide (CO₂) content by vol ume of dry flue gas under stoichiometric combustion. The desulfurization efficiency is positively correlated to the molar ratio of decomposed calcium carbonate to sulfur and negatively correlated to the free calcium oxide content of fly ash.     

湿法烟气脱硫反应过程的实验研究

在石灰石/石膏湿法烟气脱硫中试台上,系统开展了浆液pH值、飞灰浓度、液气比、入口SO2浓度、烟气速度和氧化方式等对脱硫反应过程影响的实验研究。实验表明,脱硫效率随着石膏浆液pH值、液气比的升高而增加,且入口SO2浓度越高,液气比越低,影响效应越明显;脱硫效率随着烟气速度、烟气温度和入口SO2浓度的增加而下降;石膏浆液中飞灰含量对系统脱硫效率具有一定的促进作用:pH值>5.6,飞灰浸出液中Fe3+含量相对较低,Fe3+对脱硫反应过渡态催化氧化影响程度较轻,不同工况脱硫效率差别不大。pH值<5.6,飞灰浸出液中Fe3+含量随pH值降低而增大,增效效果逐渐显著;氧化方式对脱硫反应过程有明显的影响,强制氧化工艺的脱硫效率比自然氧化的高5%左右。     

高温载硫活性炭的制备及脱汞能力研究

研究了载硫温度、硫炭比(简称S/C),吸附温度等因素对载硫活性炭的硫含量、脱汞能力以及硫损失的影响,探讨载硫活性炭制备的工艺条件优化。结果表明,不同载硫温度下制备的载硫活性炭的气态Hg0吸附能力远强于原料活性炭;载硫温度不同时,负载到活性炭孔隙或表面上的硫的形态不同,导致了脱汞能力的差异,较合适的载硫温度为350℃;S/C为5%(质量分数,下同)时,随着吸附温度的升高,载硫活性炭的气态Hg0吸附量降低;在一定的载硫温度下,原料中S/C越高时,制备的载硫活性炭的硫含量越高、气态Hg0吸附能力越强,但其硫损失率也越高,从实际的使用效果来看,较合适的S/C为10%。     

Effect of Cuscuta campestris parasitism on the physiological and anatomical changes in untreated and herbicide-treated sugar beet

The effects of field dodder on physiological and anatomical processes in untreated sugar beet plants and the effects of propyzamide on field dodder were examined under controlled conditions. The experiment included the following variants: N—noninfested sugar beet plants (control); I - infested sugar beet plants (untreated), and infested plants treated with propyzamide (1500 g a.i. ha^?1 (T₁) and 2000 g a.i. ha^?1(T₂)). The following parameters were checked: physiological—pigment contents (chlorophyll a, chlorophyll b, total carotenoids); anatomical -leaf parameters: thickness of epidermis, parenchyma and spongy tissue, mesophyll and underside leaf epidermis, and diameter of bundle sheath cells; petiole parameters: diameter of tracheid, petiole hydraulic conductance, xylem surface, phloem cell diameter and phloem area in sugar beet plants. A conventional paraffin wax method was used to prepare the samples for microscopy. Pigment contents were measured spectrophotometrically after methanol extraction. All parameters were measured: prior to herbicide application (0 assessment), then 7, 14, 21, 28 and 35 days after application (DAA). Field dodder was found to affect the pigment contents in untreated sugar beet plants, causing significant reductions. Conversely, reduction in the treated plants decreased 27% to 4% for chlorophyll a, from 21% to 5% for chlorophyll b, and from 28% to 5% for carotenoids (T₁). Also, in treatment T_2, reduction decreased in infested and treated plants from 19% to 2% for chlorophyll a, from 21% to 2% for chlorophyll b, from 23% to 3% for carotenoids and stimulation of 1% and 2% was observed 28 and 35 DAA, respectively. Plants infested (untreated) by field dodder had lower values of most anatomical parameters, compared to noninfested plants. The measured anatomical parameters of sugar beet leaves and petiole had significantly higher values in noninfested plants and plants treated with propyzamide than in untreated plants. Also, the results showed that propyzamide is an adequate herbicide for control of field dodder at the stage of early infestation.     

微波法制备污泥活性炭研究

采用微波加热法,以污水厂剩余污泥为原料,磷酸为污泥活化剂制备污泥活性炭.微波功率、辐照时间和磷酸浓度对污泥活性炭吸附性能具有显著影响,在最佳工艺条件微波功率480 W、辐照时间315 s和磷酸浓度40%条件下制得的活性炭碘值301 mg/g,比表面积168 m2/g,污泥中重金属绝大部分被固化.与传统商品炭相比,污泥炭孔隙结构以中孔为主.利用该活性炭处理城市生活污水处理厂出水,COD去除率可达87%以上,污泥炭的吸附等温线用Langmuir等温吸附模型进行描述.     

Treatment of pretreated coking wastewater by flocculation,alkali out,air stripping,and three-dimensional electrocatalytic oxidation with parallel plate electrodes

The coking wastewater generally comprises highly concentrated, recalcitrant, and toxic organic pollutants, so its treatment has been of great importance to prevent living beings and their environment from these hazardous contaminations. The treatment of pretreated coking wastewater by flocculation-coagulation, alkali out, air stripping, and three-dimensional (3-D) electrocatalytic oxidation was performed (gap between the used β-PbO₂/Ti anode and titanium cathode, 12 mm; mass ratio of Cu-Mn/granular activated carbon (GAC) to effluent, 1:4; cell voltage, 7 V). The results showed that the pH adjusting from 3.7 to 6.1 was necessary for coagulants; alkali out played an important role because it brought up precipitation containing higher fatty acids as well as other contaminants to decrease the chemical oxygen demand (COD) in the effluent, and it had also forced the reduction of ammonia nitrogen (NH₃-N) by incorporating with air stripping; for 3-D electrocatalytic oxidation with a bleaching liquid assisting, the initial pH 8.5 of effluent was suitable for Cu-Mn/GAC; moreover, it was considered that its Cu component was dedicated to the decrease of COD and NH₃-N, while the Mn component specialized in the decay of NH₃-N. The residual COD and NH₃-N values in the final effluent with pH 6.5 were 95.8 and 8.8 mg/L, respectively, demonstrating that the whole processes applied were feasible and low in cost.     

活性焦和活性炭负载纳米铁处理TNT红水中的二硝基甲苯磺酸钠

以活性焦和活性炭为载体,采用液相还原法制备了负载纳米铁,比较了两种负载纳米铁对TNT红水中难降解物质二硝基甲苯磺酸钠(包括2,4-DNT-3-SO3Na和2,4-DNT-5-SO3Na)的去除能力。实验结果表明,作为负载材料活性焦的相对有效比表面积与孔体积要优于活性炭,而且有利于更好地发挥出负载纳米铁的优势。单位面积活性焦负载纳米铁去除2,4-DNT-5-SO3Na的能力明显高于活性炭负载纳米铁,单位面积活性焦负载纳米铁去除2,4-DNT-3-SO3Na的能力在较小投加量条件下高于活性炭负载纳米铁,但均随投加量的增加而下降;而对于活性炭负载纳米铁,其单位面积去除能力基本不受投加量的影响,而且对二硝基甲苯磺酸钠的去除率高于活性焦负载纳米铁。耦合混凝沉淀的总去除效果表明,单位面活性焦负载纳米铁对2,4-DNT-5-SO3Na的去除能力高于活性炭负载纳米铁,而对2,4-DNT-3-SO3Na的去除能力则低于活性炭负载纳米铁。     

Effect of Flue Dust on the Vanadium Oxide Catalyst Utilized by the Contact Oxidation Process

Concepts for controlling SO₂ from fossil fuels can be separated into two main categories: (1) Residual and vacuum gas oil desulfurization and (2) Flue gas desulfurization. The Kiyoura-T.I.T. process confines itself to the desulfurization of flue gas. It employs vandium oxide as a catalyst which oxidizes the sulfur dioxide to trioxide, followed by a gaseous phase reaction of ammonia. The end product, ammonium sulfate is removed by an electrostatic precipitator. (The details were presented at annual meetings of APCA in 1966 and 1967 as 1 and II.) Flue gas is passed through cyclone and dust filter to remove dust. Under normal operating conditions almost all of the dust is removed at the filters. The author carried out experiments to determine whether there was any effect on the activity of the catalyst, assuming that a portion of the dust escapes into the stream along the flue. It has been generally accepted that in fuel oil firing steam power plants, about 100 mg./nm³ of dust including carbon, hydrocarbon, and ash are normally contained in the flue stream. The carbon and hydrocarbon is oxidized readily at the filters and exists only as ash. An amount of ash equivalent to the amount assumed to have settled on the catalyst over a period of 3–12 months, was placed on the catalyst, and experiments were carried out. The SO₂ conversion efficiency was measured and found to be over 93%. The results showed that at the actual operational temperature of 450°C, ash had practically no effect at all.     

3种含铁材料对重金属和砷复合污染底泥稳定化处理

选用3种含铁材料FeCl3、Fe(OH)3和FePO4,开展重金属和砷(As)复合污染底泥的稳定化处理实验,并用毒性浸出测试(TCLP)的结果和底泥交换态重金属(Pb、Cd、Cu、Zn)及As的含量来评价其稳定化效果。结果表明,(1)FeCl3和FePO4降低了底泥pH值,Fe(OH)3轻微地提高了底泥pH值。(2)FeCl3活化了底泥中Pb、Cd、Cu、Zn,使其浸出量和交换态含量增加,对As浸出量的影响不大,但使底泥中As交换态含量明显降低,且在最大添加量(8.00 g/kg)时As交换态含量未检测出;Fe(OH)3降低了Cd交换态和浸出量,稍增加了As交换态和浸出量,但对Pb、Cu、Zn交换态和浸出量影响不明显;FePO4明显降低了Pb的浸出量和交换态含量,略微降低了交换态Cd、Zn含量,对交换态Cu影响不大,但明显增加了As的浸出量和交换态含量。综上,FeCl3对As具有较好的稳定化效果,但明显活化了底泥中的4种重金属;Fe(OH)3亦对底泥中Cd有一定稳定化效果;FePO4对Pb的稳定化效果较好,但明显活化了底泥中的As。显然,3种含铁材料都不能实现底泥中重金属和As的同时稳定化。     

Comparative study on the removal efficiency of hydrogen sulfide (H2S) using three different packings

To improve the removal efficiency on hydrogen sulfide (H₂S), a biofilter was developed and was made of polyvinyl chloride (PVC) pipes. The effects of three different packings (i.e., packing A, packing B, and packing C), containing different proportions of activated carbon, sawdust, wormcast, perlite, and pig manure compost, based on different biofilter parameters on H₂S removal efficiency, were investigated. With the extension of running time, the H₂S removal rate of packing A reached up to 90.12%, that of packing B reached a peak at 92.96%, and that of packing C was highest at 87.21%. The contribution rate of each packing at the bottom of the device was significantly greater (p < 0.01) than that of other parts, and those of the top of the devices were all greater than those of the middle of the devices. The H₂S removal rate increased with greater filler layer height. The removal rate of group B increased first with humidity, and then declined, with the optimal humidity level for the removal of H₂S 50–65% in this study. With the prolongation of the run, the pH of packing A was reduced from 7.1 to 5.91, while the pH of packing B and C remained within the range of 6.53–7.10. An increase was found in the number of bacteria and fungi over time. The count of bacteria in packing B and C and following a decreasing order was bottom > middle > top, whereas that for fungi was the opposite. In conclusion, it is thought that packing B (comprising wormcast + sawdust + activated carbon) is more efficient in the removal of H₂S than the other packings and may thus be utilized in biofilters. These results hope to provide useful information for future related research on the removal efficiency of H₂S using packings.

Implications: Wormcasts use as biological filter packing to remove H₂S is limited and needs yet to be explored. A comparative study on the removal efficiency of H₂S using three packings showed the packings that included wormcast were more efficient than others, and showed the combined features of physical absorption and biological removal with long sustainability and good efficiency, although these were largely influenced by environmental factors and nutrient content for the microorganisms. In summary, wormcast could be utilized in biological filters in the future in related research beacuse of its good efficiency and low cost.     

Analysis of air quality in Dire Dawa,Ethiopia

Ambient air quality was monitored and analyzed to develop air quality index and its implications for livability and climate change in Dire Dawa, Ethiopia. Using survey research design, 16 georeferenced locations, representing different land uses, were randomly selected and assessed for sulfur dioxide (SO₂), nitrogen dioxide (NO₂), carbon dioxide (CO₂), carbon monoxide (CO),volatile organic compounds (VOCs), and meteorological parameters (temperature and relative humidity). The study found mean concentrations across all land uses for SO₂ of 0.37 ± 0.08 ppm, NO₂ of 0.13 ± 0.17 ppm, CO₂ of 465.65 ± 28.63 ppm, CO of 3.35 ± 2.04 ppm, and VOCs of 1850.67 ± 402 ppm. An air quality index indicated that ambient air quality for SO₂ was very poor, NO₂ ranged from moderate to very poor, whereas CO rating was moderate. Significant positive correlations existed between temperature and NO₂, CO₂, and CO and between humidity and VOCs. Significant relationships were also recorded between CO₂ and NO₂ and between CO and CO₂. Poor urban planning, inadequate pollution control measure, and weak capacity to monitor air quality have implications for energy usage, air quality, and local meteorological parameters, with subsequent feedback into global climate change. Implementation of programs to monitor and control emissions in order to reduce air pollution will provide health, economic, and environmental benefits to the city.

Implications: The need to develop and implement emission control programs to reduce air pollution in Dire Dawa City is urgent. This will provide enormous economic, health, and environmental benefits. It is expected that economic effects of air quality improvement will offset the expenditures for pollution control. Also, strategies that focus on air quality and climate change present a unique opportunity to engage different stakeholders in providing inclusive and sustainable development agenda for Dire Dawa.