纳米三氧化钨的制备、表征及对六硝基六氮杂异伍兹烷热分解的影响

采用水热法通过控制前躯体钨酸钠的加入量和反应时间制备了长方体形纳米WO₃,利用X射线粉末衍射(XRD)、透射电镜(TEM)、扫描电镜及能量散射光谱仪(SEM-EDS)对样品进行表征。并运用差示扫描量热法(DSC)研究纳米WO₃对六硝基六氮杂异伍兹烷(CL-20)热分解特性的影响。结果表明:与单组分CL-20相比,纳米WO₃的加入使复合物WO₃/CL-20的热分解峰温降低2.95℃,活化能减小7.74 kJ·mol^-1,因此纳米WO₃能够加速CL-20的热分解。     

以氨基化的聚苯乙烯微球为模板制备电致变色性能优良的单层有序多孔PBTB薄膜

以氯化钨和氧化石墨烯(GO)为原料,乙醇为溶剂,一步合成了WO₃纳米棒/石墨烯纳米复合材料(WO₃/RGO). 将WO₃/RGO纳米复合材料用于锂离子电池负极,并通过充放电测试、循环伏安(CV)和电化学阻抗谱(EIS)技术综合考察了该材料的储锂性能. 结果显示,在0.1C (1C=638 mA·g^-1)倍率下,复合物的首次放电比容量达到761.4 mAh·g^-1,100次循环后可逆容量仍保持在635 mAh·g^-1,保持率为83.4%. 即使在5C倍率下容量仍高达460 mAh·g^-1. 由此说明,WO₃/RGO纳米复合物具有优异的循环稳定性及倍率性能,可望用于高性能锂离子电池.     

Fe3+掺杂三维分级纳米Bi2WO6的合成及其光催化活性增强机理

利用水热法合成了Fe³⁺掺杂的三维分级纳米Bi₂WO₆,借助X射线衍射（XRD）、场发射扫描电镜（FE-SEM）、透射电镜（HRTEM）、能谱（EDS）、紫外可见漫反射（UV-Vis-DRS）等测试手段对所得样品的相组成、形貌和谱学特征进行了表征。选择罗丹明B为模型污染物研究所得样品在可见光下的催化活性。结果表明,Fe³⁺掺杂Bi₂WO₆为新颖的分级纳米结构,且Fe³⁺掺杂能有效提高Bi₂WO₆的光催化活性,Fe³⁺掺杂量对Bi₂WO₆活性的影响显著;实验结果还表明,所得Fe³⁺掺杂Bi₂WO₆催化剂的稳定性较好,易于回收。此外,还对Fe³⁺掺杂Bi₂WO₆的光催化活性增强机理进行了研究,缺电子的Fe³⁺作为电子捕获中心有利于促进光生电子-空穴对的分离,从而提高Bi₂WO₆的光催化活性。     

BiOI/Bi2WO6对甲基橙和苯酚的光催化降解及光催化机理

采用简单的沉积方法制备了不同碘化氧铋含量的BiOI/Bi₂WO₆光催化剂,通过X射线衍射(XRD)、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HR-TEM)、紫外-可见漫反射光谱(UV-VisDRS)和BET比表面积测量对其进行了表征。在紫外和可见光的照射下,使用甲基橙和苯酚的光催化降解评价了BiOI/Bi₂WO₆催化剂的光催化性能。结果表明：与商业P₂₅和纯Bi₂WO₆相比,13.2%BiOI/Bi₂WO₆光催化剂具有更高的紫外和可见光催化性能。这明显增加的光催化活性主要归功于光生电子和空穴在Bi₂WO₆和BiOI界面上的有效转移,降低了电子-空穴对的复合。基于BiOI和Bi₂WO₆的能带结构,提出了光生载流子的一种转移过程。自由基清除剂的实验表明,OH,h⁺,O₂和H₂O₂,特别是h⁺,共同支配了甲基橙和苯酚的光催化降解过程。     

Br-掺杂Bi2WO6的水热法合成及其可见光催化性能

以Bi（NO₃）₃·5H₂O和Na₂WO₄·2H₂O为主要原料,采用水热法合成了纯相Bi₂WO₆,并对其进行非金属离子Br^-掺杂改性。采用XRD、SEM、TEM、XPS、Raman、PL和DRS研究了Br^-掺杂对Bi₂WO₆的物相结构、形貌和可见光催化性能的影响。结果表明,Br^-掺杂可有效提高Bi₂WO₆的可见光催化性能,当掺杂量（物质的量百分数）为8%时,溴掺杂Bi₂WO₆的光催化性能最好,可见光照射40 min后,可降解96.73%的罗丹明-B,与未掺杂Bi₂WO₆相比,其降解率提高了36.32%。     

球状MoS2/WO3复合半导体制备及其对RhB的光催化性能

采用水热法成功制备了MoS₂/WO₃复合半导体光催化剂,分别通过SEM、TEM、EDS、XRD、Raman和DRS对催化剂的形貌,组成及结构进行表征,并用BET模型计算比表面积。对比发现球状MoS₂/WO₃对罗丹明B（RhB）的光降解效率明显高于纯WO₃、片状MoS₂/WO₃复合半导体。针对球状MoS₂/WO₃复合半导体,分别研究了MoS₂不同负载量（0.5%,1%,2%,5%,10%）对RhB光催化降解性能的影响,结果表明MoS₂含量为2%时催化效果最佳。同时,研究了溶液的pH值（pH=1,3,6,7,11）对光催化降解反应活性的影响,结果显示pH=6时降解率最高。当催化剂量增加到1 g·L^-1时,30min后RhB降解率达到96.6%。球状MoS₂/WO₃的瞬态光电流为0.050 6 mA·cm^-2,比纯WO₃提高了2.4倍。经过5次循环实验,球状MoS₂/WO₃复合半导体催化剂仍能保持90%的高降解率。     

纳米三氧化钨修饰碳纳米管载铂催化剂对甲醇氧化的电催化性能

采用表面修饰技术将碳纳米管(CNT)表面羧基化, 通过羧基将钨离子基团修饰到碳纳米管的外表面, 再通过高温焙烧处理将钨离子基团氧化成WO₃, 成功合成了纳米WO₃/CNT复合物, 进一步还原Pt 的前驱体而得到Pt-WO₃/CNT复合催化剂. 采用X射线粉末衍射(XRD)和透射电镜(TEM)对样品的形貌和晶型结构进行了表征, 结果表明, Pt纳米粒子为面心立方晶体结构, 均匀地分布在WO₃修饰的碳纳米管表面. 采用循环伏安(CV)和计时电流法研究了在酸性溶液中Pt-WO₃/CNT催化剂对甲醇的电催化氧化活性, 结果表明WO₃修饰的碳纳米管载铂催化剂比用混酸处理的碳纳米管载铂催化剂对甲醇呈现出更高的电催化氧化活性和更好的稳定性.     

S型异质结光催化剂ZnFe2O4/WO3的构筑及光催化还原CO2性能

通过在WO₃纳米片表面负载ZnFe₂O₄纳米颗粒,构建了一系列S型异质结光催化剂ZnFe₂O₄/WO₃,并研究了其光催化CO₂还原性能。在没有助催化剂和牺牲剂的条件下,所制备的ZnFe₂O₄/WO₃复合材料可对CO₂与水蒸汽进行光催化反应。优化后的材料光照5 h后CO₂还原产物CO和CH₄的产量分别为7.87和4.88 μmol·g^-1。相对于单相组分,CO和CH₄的产量明显提高。光催化活性的提高,归因于ZnFe₂O₄和WO₃异质结的形成以及光生载流子的S型电荷传输模式。     

S型异质结光催化剂ZnFe2O4/WO3的构筑及光催化还原CO2性能

通过在WO₃纳米片表面负载ZnFe₂O₄纳米颗粒,构建了一系列S型异质结光催化剂ZnFe₂O₄/WO₃,并研究了其光催化CO₂还原性能。在没有助催化剂和牺牲剂的条件下,所制备的ZnFe₂O₄/WO₃复合材料可对CO₂与水蒸汽进行光催化反应。优化后的材料光照5 h后CO₂还原产物CO和CH₄的产量分别为7.87和4.88 μmol·g^-1。相对于单相组分,CO和CH₄的产量明显提高。光催化活性的提高,归因于ZnFe₂O₄和WO₃异质结的形成以及光生载流子的S型电荷传输模式。     

水热-微波法合成纳米晶长余辉发光材料Y2O2S∶Eu3+，Mg，Ti

采用新型水热-微波法合成了纳米晶长余辉发光材料Y₂O₂S∶Eu³⁺,Mg,Ti。通过XRD、TEM、荧光光谱对其进行表征。X射线衍射测试表明所制备的Y₂O₂S∶Eu³⁺,Mg,Ti纳米发光材料为单相,六方晶。透射电子显微镜(TEM)测试表明所制备的Y₂O₂S∶Eu³⁺,Mg,Ti纳米发光材料粒径小,分布集中。激发和发射光谱测试表明Eu³⁺离子能有效地掺入硫氧化钇基质中,并具有良好的发光性能。余辉光谱测试表明其余辉颜色为红色,具有良好的余辉效果。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.