石蜡/膨胀石墨/石墨烯复合相变储热材料的制备及性能

以石蜡(PA)作为相变储热材料、 膨胀石墨(EG)作为主导热材料和支撑材料, 石墨烯气凝胶(GA)作为导热增强材料和辅支撑材料制备了PA/EG/GA复合相变材料, 研究了GA添加量对复合相变材料相变温度、 相变潜热、 导热性能以及循环稳定性的影响. 结果表明, 所制备的80%PA-17%EG-3%GA复合相变材料导热性能良好, 循环稳定性出色. 与80%PA-20%EG复合材料相比, 该材料的相变温度、 相变潜热以及循环稳定性无明显变化, 但导热系数由4.089 W/(m·K)提升到了5.336 W/(m·K), 显示出良好的应用前景.     

高耐磨低生热NBR/TBIR复合材料的结构与性能

采用高反式-1,4-丁二烯-异戊二烯共聚橡胶(TBIR)对丁腈橡胶(NBR)进行改性, 制备了高耐磨、 低生热输送轮用白炭黑填充的NBR/TBIR橡胶纳米复合材料. 研究了NBR/TBIR橡胶纳米复合材料的交联密度、 物理力学性能及填料分散性, 探讨了材料的结构对性能的影响. 研究结果表明, 与纯NBR相比, NBR/TBIR橡胶纳米复合材料的硫化速率和交联密度随TBIR用量的增加而增大; 在保持NBR硫化胶基本力学性能、 耐老化性能和耐溶剂性能基本不变的前提下, TBIR的加入使NBR/TBIR硫化胶的耐磨性提高15%, 动态压缩生热降低5%, 动态压缩永久变形降低22%, 白炭黑分散水平提高; 与丁腈橡胶/顺丁橡胶[NBR/BR(80/20), 质量份数比]硫化胶相比, NBR/TBIR(80/20, 质量份数比)硫化胶具有更低的动态压缩生热和动态压缩永久变形及更好的填料分散性.     

聚乙烯导热复合材料的电子束辐照改性

将低密度聚乙烯(LDPE)、氧化铝(Al₂O₃)和纳米二氧化硅(SiO₂)进行熔融共混,再通过电子束辐照对得到的材料进行改性,得到了同时具有高导热性能和力学性能的复合材料(PE-Al-Si)。 当纳米SiO₂的质量分数为1%,电子束辐照剂量为120 kGy时,与不含SiO₂的复合材料(PE-Al)相比,PE-Al-Si的导热系数达到了0.759 W/(m·K),提高了22%。 另外,PE-Al-Si的拉伸强度比PE-Al提高了17%。 证明SiO₂不仅可以改善复合材料的力学性能,同时还提高了辐照效率及复合材料的导热性能。     

参杂缺陷石墨烯的高分子复合材料导热特性分子动力学模拟（英文）

传统高分子材料由于内部分子链无规则缠绕的特点,导致其热导率较小。近年来,拥有高导热特性的新型高分子材料在众多领域都显示出了极大的发展潜力。随着研究的不断深入,具有优秀导热能力的石墨烯等低维碳材料引起越来越多人的关注。引入石墨烯制作的高分子复合材料具有较高的导热性能,在热管理方面具有很大的应用前景。本文使用非平衡态分子动力学方法计算了石墨烯点缺陷对石墨烯-高分子复合材料界面热导和整体热导率的影响。石墨烯层的界面热导受点缺陷密度的影响较大。当石墨烯缺陷密度由0%增大到20%时,其界面热导由75.6 MW·m~(-2)·K~(-1)增加为85.9 MW·m~(-2)·K~(-1)。石墨烯点缺陷造成sp~2共价键断裂、结构刚性下降,导致其振动态密度的低频分量增加,增强了与高分子基质间的低频能量耦合,进而提高了界面热导。而点缺陷密度的增大对复合材料整体热导率也具有相似的提升效果(从40.8 MW·m~(-2)·K~(-1)增加为45.6 MW·m~(-2)·K~(-1))。此外,高分子基体在石墨烯界面处会造成局部密度提高,但石墨烯点缺陷对高分子材料局部密度提升并无显著影响。这些计算结果加深了对石墨烯与高分子基体间导热机理的理解,并有助于开发和设计具有优异热学性能的高分子复合材料。     

酯交换反应对PBT/PC/Al_2O_3复合材料导热性能的影响

以聚对苯二甲酸丁二醇酯(PBT)与双酚A型聚碳酸酯(PC)为基体、氧化铝(Al2O3)作为导热填料,通过熔融共混法制备了PBT/PC/Al_2O_3导热复合材料,采用亚磷酸三苯酯(TPPi)作为酯交换反应抑制剂调节材料中树脂基体的相态结构,并通过红外光谱分析(FTIR)、激光导热仪、扫描电子显微镜(SEM)、示差扫描量热仪(DSC)及力学性能测试仪等对材料中的酯交换反应、导热性能、相态结构、结晶参数及力学性能进行了表征.实验结果表明,TPPi的加入可有效抑制体系中酯交换反应的发生,使PBT/PC共混物的相态结构改变,进而对填料的分布状态产生影响.当PBT/PC配比为1/1时,向其中加入1 wt%的TPPi可使体系的相态结构趋向于形成双连续相态结构,并有效提升材料的导热系数;在该体系中加入60 wt%的Al_2O_3后,材料的导热系数达到0.89 W/(m·K),相对于未加入TPPi的相同体系提升了13%.     

聚苯胺-还原氧化石墨烯复合材料的比电容及超级电容性能（英文）

通过同步还原聚苯胺(PANI)-氧化石墨烯(GO)复合物制备得到了聚苯胺-还原氧化石墨烯(PANI-rGO)。由于复合材料中PANI提供了氧化还原反应的电荷,使得PANI-rGO复合材料具有较大的比电容。通过扫描电子显微镜(SEM),紫外-可见光谱和热重量分析法(TGA)对复合物进行了结构和形态的分析。复合材料的形态呈薄片状,聚苯胺是均匀地包裹在氧化石墨烯上的。当电流密度为20 A·g~(-1)时,PANI-rGO复合材料的比电容可高达1069 F·g~(-1)(1.71 F·cm~(-2)),是PANI-GO复合材料的五倍,这是因为复合材料中还原氧化化石墨烯的大比表面和高电导性所引起的。     

甲基丙烯酸镁增强氢化丁腈橡胶的结构与形态和性能

用不同份量的甲基丙烯酸镁(MgMA)作增强剂,过氧化二异丙苯(DCP)作硫化剂,通过混炼和硫化过程的原位聚合制备了氢化丁腈橡胶/聚甲基丙烯酸镁(HNBR/PMgMA)纳米复合材料,用XRD、FTIR1、3C-NMR、SEM、TEM、DMA和交联密度分析等方法研究了其结构、形态和性能,并阐述了MgMA改性HNBR的相关机理.结果表明,MgMA在混炼过程中粒径明显变小,部分达到纳米级.硫化过程中发生原位自由基聚合,并部分接枝到HNBR分子链上,HNBR硫化胶和PMgMA有可能形成接枝互穿聚合物网络(接枝IPN).随着MgMA用量的增加,纳米复合材料硫化胶的定伸应力、拉伸强度、扯断伸长率、撕裂强度和热氧老化性能逐渐提高.当MgMA含量为30份时,体系的拉伸强度和扯断伸长率分别为38.5MPa和545%,并具有优异的热空气老化性能.MgMA能明显增加HNBR复合材料的储能模量,并降低其损耗因子.随着MgMA用量的增加,纳米复合材料硫化胶的总交联密度(Ve)和离子键交联密度(Ve2)增加,而共价键交联密度(Ve1)下降,表明离子键对HNBR/PMgMA纳米复合材料的力学性能起重要作用.     

石墨烯及其聚合物复合材料

近些年来,石墨烯以其独特的结构和优异的性质成为备受瞩目的研究前沿和热点。石墨烯作为纳米增强组分,少量添加可以使聚合物的物理性能得到大幅地提高。本文就石墨烯及其在聚合物复合材料的研究进展进行了综述,着重阐述了现已工业化制备石墨烯的氧化还原法,以及石墨烯/聚合物复合材料的制备方法(溶液共混、原位聚合和熔融共混)和性能(电学性能、导热性能、力学性能、热性能以及气体阻隔性能),并指出其待解决的关键技术及工业化前景。     

有机相化学镀铝法制备Al/石墨烯复合材料粉末

采用有机相化学镀法制备了Al/石墨烯复合材料粉末。使用傅里叶红外光谱仪、拉曼光谱仪、ASAP2020全自动快速比表面与孔隙度分析仪和配备EDS能谱的扫描电子显微镜表征样品。结果表明,镀铝后,石墨烯表面的含氧基团基本消失,发生空间弯曲折叠形成包覆结构,导致中孔和大孔的形成,石墨烯层间距变大。此外,氮气吸附-脱附结果显示,Al/石墨烯复合材料粉末的孔道以微孔和中孔为主,Brunauer-Emmett-Teller比表面积为91 m~2·g~(-1);通过Barret-Joyner-Halenda解吸模型计算得到的平均孔径为8.77 nm,孔体积为0.45 cm~3·g~(-1)。X射线衍射分析并没有发现Al_4C_3晶体结构的出现,表明镀铝过程并未或生成很少(小于检测下限)脆相Al_4C_3。最后,微观表面分析表明,当加入的NaH量略大于理论值时,实验结果与理想体系基本吻合,镀铝效果最佳。     

石墨烯/聚乙烯界面导热性能的分子动力学模拟

采用非平衡分子动力学模拟(NEMD)方法研究了石墨烯/聚乙烯纳米复合材料的界面导热性能,主要考察了石墨烯层数、尺寸对界面热阻的影响.研究结果表明:当石墨烯层数为一层时,界面热导为46.79 MW/(m~2K),随着石墨烯层数的增加,界面热导下降;但石墨烯层数超过四层后,界面热导趋于恒定接近39.00 MW/(m~2K);随着石墨烯尺寸的增大,石墨烯中较长波长声子被引发并对界面热传导起到主要的作用,最终导致界面热导逐渐增大.     

Multifunctional elastomer nanocomposites with functionalized graphene single sheets

We demonstrate the use of functionalized graphene sheets (FGSs) as multifunctional nanofillers to improve mechanical properties, lower gas permeability, and impart electrical conductivity for several distinct elastomers. FGS consists mainly of single sheets of crumbled graphene containing oxygen functional groups and is produced by the thermal exfoliation of oxidized graphite (GO). The present investigation includes composites of FGS and three elastomers: natural rubber (NR), styrene–butadiene rubber, and polydimethylsiloxane (PDMS). All of these elastomers show similar and significant improvements in mechanical properties with FGS, indicating that the mechanism of property improvement is inherent to the FGS and not simply a function of chemical crosslinking. The decrease in gas permeability is attributed to the high aspect ratio of the FGS sheets. This creates a tortuous path mechanism of gas diffusion; fitting the permeability data to the Nielsen model yields an aspect ratio of ～1000 for the FGS. Electrical conductivity is demonstrated at FGS loadings as low as 0.08% in PDMS and reaches 0.3 S/m at 4 wt % loading in NR. This combination of functionalities imparted by FGS is shown to result from its high aspect ratio and carbon‐based structure. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

A Novel L‐Cysteine Electrochemical Sensor Using Sulfonated Graphene‐poly(3,4‐Ethylenedioxythiophene) Composite Film Decorated with Gold Nanoparticles

By exploiting the electrostatic interaction between positively charged 3,4‐ethylenedioxythiophene cation radicals and negatively charged sulfonated graphene (SG) sheets, we prepared a poly(3,4‐ethylenedioxythiophene)‐sulfonated graphene (SG‐PEDOT) composite film by a one‐step electrochemical process. The composite was further decorated with gold nanoparticles (AuNPs) and employed as an electrode material for the detection of L ‐cysteine (Cys). The SG‐PEDOT composite film is shown to provide a rough surface for the electrodeposition of AuNPs and to improve substrate accessibility and interaction with Cys. Moreover, the AuNPs‐decorated composite exhibits better electrocatalytic performance than that of a SG‐PEDOT composite only. Under optimum experimental conditions, the amperometric current of the sensor is linearly related to the concentration of Cys in the 0.1 to 382 µM range, and the detection limit is 0.02 µM (at S/N=3). The modified electrode displays favorable selectivity, good stability and high reproducibility. The method was successfully applied to the detection of Cys in spiked human urine.     

Experimental test and curve fitting of creep recovery characteristics of modified graphene oxide natural rubber and its relationship with temperature

The creep recovery properties of different graphene-doped rubber and the effect of temperature on them were studied. Doping graphene, especially with the surface functional group or surface microstructure, can significantly improve the creep resistance of natural rubber (NR). The permanent creep of each composite tested under the same conditions for 20 min. Graphene oxide, hydrazine hydrate reduced graphene oxide, and 3-aminopropyltriethoxysilane (APTS) grafted graphene oxide was 33%, 16%, and 51% lower than those filled with carbon black respectively. Four parameter model and Weibull distribution function used to analyze and evaluate the creep and recovery test results of composite rubber. These curve fitting results can adequately describe the influence of different types of nanofillers on the creep and recovery properties of composite rubber. The long-term creep of composites forecasted by the time-temperature superposition principle (TTSP). The results show that graphene doping can improve the creep resistance of the rubber. Besides, graphene oxide and surface-modified graphene oxide had better creep resistance than reduced graphene oxide filled natural rubber. It can see that the interfacial properties between the graphene sheet and the natural rubber matrix play an essential role in the creep and recovery properties of graphene/natural rubber composites.     

Performance improvement of EPDM and EPDM/Silicone rubber composites using modified fumed silica,titanium dioxide and graphene additives

In this work, a polymeric composite was prepared from ethylene propylene diene monomer (EPDM) and silicone rubber (S) with additives of modified fumed silica (MFS), titanium dioxide (TiO₂) and graphene. The dielectric and thermal performances of the EPDM-based composites were studied. An increase in the dielectric constant and AC dielectric breakdown strength was observed for the EPDM rubber composites containing MFS, TiO_2, and graphene additives. In addition, the incorporation of the additives resulted7in a significant increase in the thermal stability (~30–50 °C) and thermal conductivity (~7–35%) of the composites. The combination of these various improvements gives suitable performance advantage to the polymeric composite for use in insulating applications.     

石墨烯包覆天然球形石墨作为锂离子电池的负极材料，是否需要乙炔黑导电剂？

我们通过包覆炭化的方法制备得到了石墨烯包覆的天然球形石墨(G/SG)材料,并使用扫描电子显微镜、X射线衍射仪以及多种电化学测试手段考察了不同石墨烯含量的复合材料的形貌结构及电化学性能。我们发现,在不添加乙炔黑(AB)的情况下,G/SG复合材料表现出较高的首次库伦效率,很好的循环稳定性和高倍率性能。当石墨烯包覆量为1%时,材料50次循环后的可逆容量可与添加10%AB的天然石墨电极(SG)等同;当石墨烯包覆量为2.5%时,材料的比容量完全高于添加10%AB的石墨电极。材料电化学性能的改善归因于石墨烯的包覆。一方面,石墨烯的柔软可变性可以保证天然石墨颗粒在充放电过程中的结构完整性,从而有效改善材料的循环稳定性;另一方面,石墨烯的存在提高了电极的导电性,促进更好导电网络的形成。因此,石墨烯包覆天然球形石墨材料中,石墨烯不仅是活性物质,也发挥导电剂的作用。当添加5%的乙炔黑时,在50 mA·g^-1电流循环50次后,5%G/SG电极的可逆容量从381.1 mAh·g^-1提高到404.5 mAh·g^-1,在1 A·g^-1电流时可逆容量从82.5 mAh·g^-1提高到101.9 mAh·g^-1,这表明G/SG电极仍然需要乙炔黑导电剂。乙炔黑颗粒填充在复合材料的空隙中,通过点接触的形式连接到G/SG颗粒,与石墨烯协同作用形成了更加有效的导电网络。尽管石墨烯包覆和乙炔黑添加对天然石墨电极具有积极的影响,例如增加了天然石墨电极的导电性和储锂性能(包括可逆容量,倍率性能和循环性能),但随着石墨烯或乙炔黑的增加,电极密度通常会降低。因此,在实际应用中应考虑石墨负极材料的质量和体积容量的平衡。这些结果对天然石墨的进一步商业应用具有重要意义。我们的工作为天然石墨电极在锂电池中的电化学行为提供了一种新的认识,并且有助于制备更高性能的负极材料。     

Hybird Membrane with High Proton Conductivity and Selectivity Based on SPEEK for Direct Methanol Fuel Cells

Composite membranes based on sulfonated silica/sulfonated poly(ether ether ketone)(SPEEK) were prepared by means of sol-gel method so as to gain a high conductivity and reasonable methanol permeability.The sulfonated silica is generated in situ via the hydrolysis of sulfonated 3-anminopropyl triethoxysilane(KH550) synthesized newly from 3-aminopropyl triethoxysilane and 1,4-butane sultone.The membrane with a silica mass fraction of 5% exhibits a conductivity of 0.187 S/cm at 80 °C and a methanol coefficient with 9.72×10-7 cm2/s.The composite membranes show improved condutive ability and better selectivity that can be promisingly used in direct methanol fuel cell.     

含氨基聚芳醚酮/磺化聚芳醚酮砜中高温质子交换复合膜的制备与性能研究

以自制的高磺化度磺化聚芳醚酮砜(SPAEKS)和含有氨基的聚芳醚酮(Am-PAEK)为原料,通过共溶剂涂膜法制备了不同重量比例的Am-PAEK/SPAEKS复合膜.通过高温(160℃)处理使氨基和磺酸基团在复合膜内形成交联,制得交联型复合膜.复合膜的热性能、尺寸稳定性、阻醇性能有所提高,而且交联型复合膜中的Am-PAEK/SPAEKS-C-3质子传导率在120℃时达到了0.0892 S/cm,高于在相同测试条件下SPAEKS膜的0.0654 S/cm和Nafion膜的0.062 S/cm,而其甲醇渗透系数在25℃时达到0.14×10-6cm2/s,低于SPAEKS膜的0.85×10-6cm2/s和Nafion膜的2×10-6cm2/s.实验结果表明,Am-PAEK/SPAEKS交联型复合膜有望在中高温质子交换膜燃料电池中得到应用.     

Sulfonated carbon nanotubes/sulfonated poly(ether sulfone ether ketone ketone) composites for polymer electrolyte membranes

A series of composite membranes consisting of sulfonated carbon nanotubes (sCNTs) and sulfonated poly(ether sulfone ether ketone ketone) were successfully fabricated via the solution casting method. The chemical structure, as well as the long‐term stability of the sCNTs in different solvents, was investigated by Fourier transform infrared (FTIR) analysis and solubility experiment, respectively. The morphology, tensile strength, proton conductivity, and methanol permeability of the composite membranes were also investigated. The scanning electron microscope (SEM) observation indicated the good dispersion of the carbon nanotubes in polymer matrix as well as the strong interfacial bonding between the sulfonated poly(ether sulfone ether ketone ketone) (SPESEKK) matrix and sCNTs. The addition of either pristine carbon nanotubes or modified carbon nanotubes significantly enhanced the tensile strength of the SPESEKK membrane. The proton conductivity of the SPESEKK membrane increased while the methanol permeability decreased as the sCNTs content increased, showing a strong interaction between the modified nanotubes and SPESEKK. Copyright © 2010 John Wiley & Sons, Ltd.     

A composite polyaniline/graphene–coated polyamide6 nanofiber mat for electrochemical applications

In this study, polyamide6 (PA6) nanofiber mats were fabricated through the electrospinning process. The nanofibers were coated by polyaniline (PANI) using the in situ polymerization of aniline in the presence of graphene oxide. The composite of the PANI/graphene oxide–coated nanofiber mat was treated with hydrazine monohydrate to reduce graphene oxide to graphene, and this was followed by the reoxidation of PANI. Field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), thermal gravimetric analysis (TGA), tensile strength tests, electrical conductivity measurements, cyclic voltammetry (CV), and charge/discharge measurements were conducted on the composite PA6/graphene nanofiber mats. It was found that the surface of the PA6 nanofibers was coated uniformly with the granular PANI and graphene oxide. Besides, the composite nanofibers showed good tensile and thermal properties. Their electrical conductivity and specific capacitance, when used as a separator in the cell, were 1.02 × 10^?4 S/cm and 423.28 F/g, respectively. Therefore, the composite PANI/reduced graphene oxide–coated PA6 nanofiber mats could be regarded as suitable candidates for application in energy storage devices.     

A study of the thermal properties of bamboo knitted fabrics

In this research, the thermal properties of bamboo single jersey knitted fabrics have been studied in relation to stitch length and yarn linear density in tex. The objective was to determine the influence of fabric factors like stitch length and the constituent yarn linear density on fabric properties, such as air permeability, thermal conductivity, thermal resistance and relative water vapour permeability. Yarns with linear densities of 19.6, 23.6, 29.5 tex and with the same twist level were used to construct the fabrics of single jersey structure with stitch lengths of 0.27, 0.29 and 0.31 cm. The anticipated increase in air permeability and relative water vapour permeability with decrease in yarn linear density and increase in stitch length was observed. The thermal conductivity and thermal resistance tended in general to increase with constituent yarn linear density but decreased with increase in stitch length.