Nonlinear Finite-Element Analysis for Highway Bridge Superstructures

The most popular type of bridge in service today is the concrete deck on steel-girder composite bridge. A finite-element model is built to analyze the superstructure of this type of bridge under working load conditions. The deflections along a test bridge are computed by using this method; the results obtained are close to the experimental data. The concrete deck of the bridge is analyzed using nonlinear finite elements, of which the analytical procedure is described in detail. A comparison is also made between this method and the traditional transformed area method.     

Modal Testing, Finite-Element Model Updating, and Dynamic Analysis of an Arch Type Steel Footbridge

This paper describes an arch type steel footbridge, its analytical modeling, modal testing, finite-element model updating, and dynamic analysis. A modern steel footbridge which has an arch type structural system and is located on the Karadeniz coast road in Trabzon, Turkey is selected as an application. An analytical modal analysis is performed on the developed three-dimensional finite-element model of footbridge to provide analytical frequencies and mode shapes. Field ambient vibration tests on the footbridge deck under natural excitation such as human walking and traffic loads are conducted. The output-only modal parameter identification is carried out by using peak picking of the average normalized power spectral densities in the frequency domain and stochastic subspace identification in the time domain, and dynamic characteristics such as natural frequencies, mode shapes, and damping ratios are determined. The finite-element model of the footbridge is updated to minimize the differences between analytically and experimentally estimated modal properties by changing some uncertain modeling parameters such as material properties. Dynamic analyses of the footbridge before and after finite-element model updating are performed using the 1992 Erzincan earthquake record. At the end of the study, maximum differences in the natural frequencies are reduced from 22 to only 5% and good agreement is found between analytical and experimental dynamic characteristics such as natural frequencies and mode shapes by model updating. Also, maximum displacements and principal stresses before and after model updating are compared with each other.     

Dynamic Response of a Highway Bridge Subjected to Moving Vehicles

Several full-scale load tests were performed on a selected Florida highway bridge. The bridge was dynamically excited by two fully loaded trucks, and the strain, acceleration, and displacement at selected points were recorded for the investigation of the bridge’s dynamic response. Experimental data were compared with simplified vehicle and bridge finite-element models. The vehicle was represented as a three-dimensional mass–spring–damper system with 11?degrees of freedom, and the bridge was modeled as a combination of plate and beam elements that characterize the slab and girders, respectively. The equations of motion were formulated with physical components for the vehicle and modal components for the bridge. The coupled equations were solved using a central difference method. It was found that the numerical analysis matched well with the experimental data and was used to successfully explain critical dynamic phenomena observed during the testing. Impact factors for this tested bridge were thoroughly investigated by using these models.     

Experimental Evaluation of Dynamic Effects for a Selected Highway Bridge

The paper presents an experimental study of the actual dynamic effects for a preselected typical highway bridge. Knowledge of the dynamic impact factors is important for accurate determination of the ultimate load capacity and performance assessment of constructed bridges. Static and dynamic field tests were performed on a two-lane concrete highway bridge built in 1999 on U.S. 90 in northwest Florida. During the tests, one or two fully loaded trucks crossed over the bridge, which was instrumented with strain gauges, accelerometers, and displacement transducers. A wooden plank was placed across the lanes for some runs to trigger extensive dynamic vibration and to simulate poor road surface conditions. Data collected from the tests were used for comprehensive assessment of the bridge under dynamic loading. Impact factors obtained from the tests with higher speeds were found larger than corresponding values recommended by bridge codes. Analysis revealed that stiff vehicle suspension, road surface imperfection, and “bouncing” of the truck loading contributed to the high impact factors. Experimental data were also used for validation of the finite-element models developed for the vehicle–bridge system.     

Finite-Element Analysis of Steel Bridge Distortion-Induced Fatigue

Welded plate girder bridges built before the mid-1980s are often susceptible to fatigue cracking driven by out-of-plane distortion. However, methods for prediction of secondary stresses are not specifically addressed by bridge design specifications. This paper presents a finite-element study of a two-girder bridge that developed web gap cracks at floortruss-girder connections. The modeling procedures performed in this research provide useful strategies that can be applied to determine the magnitude of distortion-induced stresses, to describe the behavior of crack development, and to assess the effectiveness of repair alternatives. The results indicate severe stress concentration at the crack initiation sites. The current repair method used at the positive moment region connections is found acceptable, but that used at the negative moment region connections is not satisfactory, and additional floortruss member removal is required. Stress ranges can be lowered below half of the constant amplitude fatigue threshold, and fatigue cracking is not expected to recur if the proposed retrofit approach is carried out.     

Bridge Structural Condition Assessment Using Systematically Validated Finite-Element Model

The structural condition assessment of highway bridges is largely based on visual observations described by subjective indices, and it is necessary to develop a methodology for an accurate and reliable condition assessment of aging and damaged structures. This paper presents a method using a systematically validated finite-element model for the quantitative condition assessment of a damaged reinforced concrete bridge deck structure, including damage location and extent, residual stiffness evaluation, and load-carrying capacity assessment. In a trial of the method in a cracked bridge beam, the residual stiffness distribution was determined by model updating, thereby locating the damage in the structure. Furthermore, the damage extent was identified through a defined damage index and the residual load-carrying capacity was estimated.     

Dynamic Monitoring of Steel Girder Highway Bridge

Currently there are different monitoring techniques that have been considered for use in the structural evaluation of bridges. These include approaches based on both static and dynamic behavior. The use of dynamic properties has advantages over static properties, since components of the dynamic properties are only marginally influenced by variations in the loading. When dynamic properties are used, field studies have shown that it is not always sufficient to use only natural frequencies and modal displacements. Some research for structural evaluation of bridges indicates that techniques based on use of derivatives of the natural frequencies and the modal displacements may be more effectively used to generate effective diagnostic parameters for structural identification. This paper presents the results of applying one of these methods, the modal flexibility approach, to a field study of a bridge in which the bearings were partially restrained in colder weather. While others have used impact methods with the modal flexibility method, in this study the approach is modified so that excitation is provided by vehicular traffic. The results show that the modified modal flexibility method provides a clear indication that there have been changes in the bridge’s structural behavior.     

Ultimate Capacity Destructive Testing and Finite-Element Analysis of Steel I-Girder Bridges

Current bridge design and rating techniques are based at the component level and thus cannot predict the ultimate capacity of bridges, which is a function of system-level interactions. While advances in computer technology have made it possible to conduct accurate system-level analyses, which can be used to design more efficient bridges and produce more accurate ratings of existing structures, the knowledge base surrounding system-level bridge behavior is still too small for these methods to be widely considered reliable. Thus, to advance system-level design and rating, a 1/5-scale slab-on-steel girder bridge was tested to ultimate capacity and then analytically modeled. The test demonstrated the significant reserve capacity of the steel girders, and the response of the specimen was governed by the degradation of the reinforced-concrete deck. To accurately capture the response of the specimen in an analytical model, the degradation of the deck and other key features of the specimen were modeled by using a dynamic analysis algorithm in a commercially available finite-element analysis program ABAQUS.     

Refined Stick Model for Dynamic Analysis of Skew Highway Bridges

Stick models are widely employed in the dynamic analysis of bridges when only approximate results are desired or when detailed models are difficult or time-consuming to construct. Although the use of stick models for regular bridges has been validated by various researchers, the application of such models to skew highway bridges continues to present challenges. The conventional single-beam stick model used to represent the bridge deck often fails to capture certain predominant vibration modes that are important in obtaining the true dynamic response of the bridge. In this paper, a refined stick model is proposed for the preliminary dynamic analysis of skew bridges. The model utilizes a dual-beam stick representation of the bridge deck. The validity of the model is established by comparing results obtained from the proposed model with numerical solutions obtained for skew plates and a skew bridge. It is shown that this dual-beam stick model is superior to the conventional single-beam model in estimating the natural vibration frequencies and in predicting the predominant vibration modes of the bridge. Because of its simplicity and relative accuracy, this model is recommended for the preliminary dynamic analysis of skew highway bridges.     

Finite-Element Analysis and Vibration Testing of a Two-Span Masonry Arch Bridge

This paper presents the analytical modeling, modal testing, and finite-element model updating for a two-span masonry arch bridge. An Ottoman masonry arch bridge built in the 19th century and located at Camlihemsin, Rize, Turkey is selected as an example. Analytical modal analysis is performed on the developed 3D finite-element model of the bridge to obtain dynamic characteristics. The ambient vibration tests are conducted under natural excitation such as human walking. The operational modal analysis is carried out using peak picking method in the frequency domain and stochastic subspace identification method in the time domain, and dynamic characteristics (natural frequencies, mode shapes, and damping ratios) are determined experimentally. Finite-element model of the bridge is updated to minimize the differences between analytically and experimentally estimated dynamic characteristics by changing boundary conditions. At the end of the study, maximum differences in the natural frequencies are reduced on average from 18 to 7% and a good agreement is found between analytical and experimental dynamic characteristics after finite-element model updating.     

Load Distribution for a Highly Skewed Bridge: Testing and Analysis

The American Association of State Highway and Transportation Officials (AASHTO) specifications provide formulas for determining live load distribution factors for bridges. For load distribution factors to be accurate, the behavior of the bridge must be understood. While the behavior of right-angle bridges and bridges with limited skews is relatively well understood, that of highly skewed bridges is not. This paper presents a study aimed at developing a better understanding of the transverse load distribution for highly skewed slab-on-steel girder bridges. The study involved both a diagnostic field test of a recently constructed bridge and an extensive numerical analysis. The bridge tested and analyzed is a two-span, continuous, slab-on-steel composite highway bridge with a skew angle of 60°. The bridge behavior is defined based on the field test data. Finite-element analyses of the bridge were conducted to investigate the influence of model mesh, transverse stiffness, diaphragms, and modeling of the supports. The resulting test and analytical results are compared with AASHTO’s Load and Resistance Factor Design formulas for live load distribution to assess the accuracy of the current empirical formulas.     

Bridge Model Updating Using Response Surface Method and Genetic Algorithm

A finite-element (FE) model of a structure is a highly idealized engineering model that may or may not truly reflect the physical structure. The purpose of model updating is to modify the FE model of a structure in order to obtain better agreement between the numerical and field-measured structure responses. In this paper, a new practical and user-friendly FE model updating method is presented. The new method utilizes the response surface method for the best experimental design of the parameters to be updated based on which numerical analysis can be performed in order to obtain explicit relationships between the structural responses and parameters from the simulation results. The parameters are then be updated using the genetic algorithm (GA) by minimizing an objective function. A numerical example of a simply supported beam has been used to demonstrate the concept. This method has also been applied to the model updating of an existing bridge. Results show that this method works well and achieves reasonable physical explanations for the updated parameters.     

Dynamic Testing for Structural Identification of a Bridge

Structural identification via modal analysis in structural mechanics is gaining popularity in recent years, despite conceptual difficulties connected with its use. This paper is devoted to illustrating the advantages and also the indeterminacy characterizing structural identification problems for bridge structures, even in rather simple instances. In particular, an identification procedure based on modal analysis and finite-element model updating is presented for the characterization of a concrete bridge whose constructive typology is quite diffuse in the area of Friuli Venezia Giulia, Italy. Experience has suggested (so as to restrict the indeterminacy frequently affecting identification issues) resorting to all the a priori information on the system and mindfully selecting the parameters to be identified. The analysis pointed out some particularities in the modeling of bridge typology under study, otherwise not a priori detectable from an analytical point of view.     

Modal Contribution Coefficients in Bridge Condition Evaluation

Impact modal testing combined with finite element (FE) analyses is currently being used to evaluate the condition of steel bridges in the state of Ohio. Using modal testing techniques, it is relatively easy to measure the dynamic response of bridges, including mode shapes, frequencies, and modal scaling factors. These responses are compared to the results of the FE analyses and the model is iteratively updated until a good agreement is obtained. After a good agreement between experimental and analytical results has been achieved, the FE model is used to obtain stresses that are used to load rate the bridge. During the iterative calibration process, several quantities, including the fundamental mode shapes and frequencies, are used to evaluate the accuracy of the FE model. Since each mode shape plays a different role in the dynamic behavior of the structure, a more efficient calibration routine can be achieved if more emphasis is placed on obtaining good matches for the modes that are most influential. The aim of this paper is to develop a quantitative measure of the contribution of different modes to the overall dynamic response of a structure. The proposed measure, a series of contribution coefficients, is used to identify which modes are most critical in the process of modal testing and FE model calibration. Several applications of the contribution coefficients are identified.     

Construction and Testing of an Innovative Concrete Bridge Deck Totally Reinforced with Glass FRP Bars: Val-Alain Bridge on Highway 20 East

The Val-Alain Bridge, located in the Municipality of Val-Alain on Highway 20 East, crosses over Henri River in Québec, Canada. The bridge is a slab-on-girder type with a skew angle of 20° over a single span of 49.89?m and a total width of 12.57?m. The bridge has four simply supported steel girders spaced at 3,145?mm. The deck slab is a 225-mm-thick concrete slab, with semi-integral abutments, continuous over the steel girders with an overhang of 1,570?mm on each side. The concrete deck slab and the bridge barriers were reinforced with glass fiber reinforced polymer (GFRP) reinforcing bars utilizing high-performance concrete. The Val-Alain Bridge is the Canada’s first concrete bridge deck totally reinforced with GFRP reinforcing bars. Using such nonmetallic reinforcement in combination with high-performance concrete leads to an expected service life of more than 75?years. The bridge is well instrumented with electrical resistance strain gauges and fiber-optic sensors at critical locations to record internal strain data. Also, the bridge was tested for service performance using calibrated truckloads. Design concepts, construction details, and results of the first series of live load field tests are presented.     

Dynamic Characteristics and Effective Stiffness Properties of Honeycomb Composite Sandwich Structures for Highway Bridge Applications

In this paper, a combined analytical and experimental study of dynamic characteristics of honeycomb composite sandwich structures in bridge systems is presented, and a relatively simple and reliable dynamic experimental procedure to estimate the beam bending and transverse shear stiffness is proposed. This procedure is especially practicable for estimating the beam transverse shear stiffness, which is primarily contributed by the core and is usually difficult to measure. The composite sandwich beams are made of E-glass fiber and polyester resins, and the core consists of the corrugated cells in a sinusoidal configuration. Based on the modeling of equivalent properties for the face laminates and core elements, analytical predictions of effective flexural and transverse shear stiffness properties of sandwich beams along the longitudinal and transverse to the sinusoidal core wave directions are first obtained. Using piezoelectric sensors, the dynamic response data are collected, and the dynamic characteristics of the sandwich structures are analyzed, from which the flexural and transverse shear stiffness properties are reduced. The experimental stiffness results are then compared to the analytical stiffness properties, and relatively good correlations are obtained. The proposed dynamic tests using piezoelectric sensors can be used effectively to evaluate the dynamic characteristics and stiffness properties of large sandwich structures suitable for highway bridge applications.     

Nonlinear Finite-Element Analysis of Posttensioned Concrete Bridge Girders

Posttensioning is an effective method for the construction of different types of bridge girders such as those used in segmentally erected bridges. Available nonlinear analysis programs for bridge girders under severe loading conditions are computationally expensive though. In addition, they neglect important phenomena such as bond-slip, friction, and anchorage losses. The objective of the proposed work is to develop a new nonlinear finite-element program for analysis of posttensioned bridge girders. The new model overcomes most of the difficulties associated with existing models. The model is based on the computationally efficient mixed formulation and considers bond, friction, and anchorage loss effects. The mixed formulation is characterized by its fast convergence, usually with very few finite elements and its robustness even under severe loading conditions. The posttensioning operation is accurately simulated using a phased-analysis technique, in which each stage of the posttensioning operation is simulated through a complete nonlinear analysis procedure. Correlation studies of the proposed model with experimental results of posttensioned specimens are conducted. These studies confirmed the accuracy and efficiency of the newly developed software program, which represents an advancement over existing commercial software packages for evaluating posttensioned bridge girders, in particular those subjected to severe loading conditions.     

Roebling Suspension Bridge. I: Finite-Element Model and Free Vibration Response

This first part of a two-part paper on the John A. Roebling suspension bridge (1867) across the Ohio River is an analytical investigation, whereas Part II focuses on the experimental investigation of the bridge. The primary objectives of the investigation are to assess the bridge’s load-carrying capacity and compare this capacity with current standards of safety. Dynamics-based evaluation is used, which requires combining finite-element bridge analysis and field testing. A 3D finite-element model is developed to represent the bridge and to establish its deformed equilibrium configuration due to dead loading. Starting from the deformed configuration, a modal analysis is performed to provide the frequencies and mode shapes. Transverse vibration modes dominate the low-frequency response. It is demonstrated that cable stress stiffening plays an important role in both the static and dynamic responses of the bridge. Inclusion of large deflection behavior is shown to have a limited effect on the member forces and bridge deflections. Parametric studies are performed using the developed finite-element model. The outcome of the investigation is to provide structural information that will assist in the preservation of the historic John A. Roebling suspension bridge, though the developed methodology could be applied to a wide range of cable-supported bridges.     

Innovative Bridge Condition Assessment from Dynamic Response of a Passing Vehicle

An innovative approach for damage assessment of a bridge deck is proposed with the measured dynamic response of a vehicle moving on top of a structure. The simply supported bridge deck is modeled as a Euler–Bernoulli beam. The moving vehicle serves as a smart sensor and force transducer in the structural system. The damage is defined as the flexural stiffness reduction in the beam finite element. The identification algorithm is based on dynamic response sensitivity analysis, and it is realized with a regularization technique from the measured vehicle acceleration measurement. Measurement noise, road surface roughness, and model errors are included in the simulations, and the results indicate that the proposed algorithm is computationally stable and efficient, and the identified results are acceptable and not sensitive to the different parameters studied.     

Full-Scale Test and Analysis of a Curved Steel-Box Girder Bridge

Since the first edition of the AASHTO Guide Specifications for Horizontally Curved Steel Girder Highway Bridges was published in 1980, there have been two more editions including many revisions to the specifications. Some changes were based on valid research results and others were based on limited or uncertain research results and information. The current edition of the specifications contains provisions that may result in unreasonably conservative load capacity ratings. In this paper, the results of field tests and analyses conducted on the Veterans’ Memorial curved steel-box girder bridge are discussed. Test and analytical results show: (1) current AASHTO guide specifications regarding the first transverse stiffener spacing at the simple end support of a curved girder may be too conservative for bridge load capacity ratings; (2) current AASHTO guide specifications may greatly overestimate the dynamic loadings of curved box girder bridges with long span lengths; and (3) a plane grid finite-element model of about 20 elements per span in the longitudinal direction can be used to analyze curved multigirder bridges with external bracings located only over supports. The research results are instructive and applicable to bridge design and bridge load-rating activities.