Graphene modified Co–B catalysts for rapid hydrogen production from NaBH4 hydrolysis

Graphene oxide (GO) modified Co–B catalysts for NaBH₄ hydrolysis have been synthesized by the chemical reduction in this work. The structural features and catalytic performance of as-prepared samples have been investigated and discussed as a function of amounts of GO. According to structure characterization, the catalysts still retain the amorphous structure of Co–B alloy with the addition of GO, while GO exists as reduced GO (r-GO). The textural analysis and morphology observation indicate that the appropriate amount of GO in Co–B catalyst results in the obvious increase of specific surface area and uniform clustered morphology, which contributes to improve active surface area for catalytic reactions. The results of surface species characterization show that the electron density at active Co sites increases due to an electron transfer from B to Co facilitated by r-GO. It has been found that 50 mg GO modified Co–B catalyst exhibits especially high activity with a hydrogen generation rate of 14.34 L min⁻¹·g_catalyst⁻¹ and much lower activation energy of 26.2 kJ mol⁻¹ for hydrolysis reaction of NaBH₄. Meanwhile, the reusability evaluations show that the catalyst preserves high stability which can still maintain 81.5% of its initial activity after 5 catalytic cycles.     

Protection and confinement effect of carbon on Co/CoxOy nano-catalyst for efficient NaBH4 hydrolysis

The hydrolysis of sodium borohydride (NaBH₄) over catalysts is a promising method to produce hydrogen. Although Co-based catalysts exhibit high activity for NaBH₄ hydrolysis, they are still far from satisfying practical applications, especially their poor durability in alkaline media. Herein, a carbon shell structure was designed and synthesized to improve the stability of the mixture of Co⁰ and Co_xO_y nanofilms (Co/Co_xO_y@C) during NaBH₄ hydrolysis via a facile polymerization-pyrolysis strategy with Co/Co_xO_y nanofilms as the precursor. As a result, the Co/Co_xO_y@C catalyst can achieve a remarkable H₂ generation rate of 4348.6 mL min^?1 g_Co^?1 with a low activation energy of 43.6 kJ mol^?1, which is superior to most previously reported catalysts. Moreover, the catalyst shows high stability with an H₂ generation-specific rate of 79% after five cycles. The excellent performance of carbon substrate can well prevent the agglomeration of Co-based nanoparticle and improve the corrosion resistance of the active Co to BO₂^? and OH^?. This work would widen the road for the preparation of nanoconfined catalysts, which has prospective application potentials for H₂ production from NaBH₄ hydrolysis.     

Hydrogen generation from alkaline NaBH4 solution using nanostructured Co–Ni–P catalysts

In the present study, nanostructured Co–Ni–P catalysts have been successfully prepared on Cu sheet by electroless plating method. The morphologies of Co–Ni–P catalysts are composed of football-like, granular, mockstrawberry-like and shuttle-like shapes by tuning the depositional pH value. The as-deposited mockstrawberry-like Co–Ni–P catalyst exhibits an enhanced catalytic activity in the hydrolysis of NaBH₄ solution. The hydrogen generation rate and activation energy are 2172.4 mL min⁻¹ g⁻¹ and 53.5 kJ mol⁻¹, respectively. It can be inferred that the activity of catalysts is the result of the synergistic effects of the surface roughness, the particle size and microscopic architectures. Furthermore, the stability of mockstrawberry-like Co–Ni–P catalyst has been discussed, and the hydrogen generation rate remains about 81.4% of the initial value after 5 cycles.     

Magnetically recyclable Fe@Co core-shell catalysts for dehydrogenation of sodium borohydride in fuel cells

Co-based catalysts of the reaction by which hydrogen was obtained from NaBH₄ solution were prepared by chemical reduction in a liquid phase. X-ray diffraction and scanning electron microscopy analyses showed that the as-prepared Fe@Co catalyst was ultrafine and amorphous. The calculated Arrhenius activation energy of the Fe@Co catalyst was 35.62(1) kJ mol⁻¹ while that of the Co catalyst was 38.81(2) kJ mol⁻¹, demonstrating that Fe@Co nanoparticles reduce the activation energy of the reaction more than does a Co nanocatalyst. X-ray absorption spectroscopy (XAS) clearly reveals the valences of Fe and Co. The Fe valence of Fe@Co is smallest among three catalysts because of the Co shell. The molar ration of Fe to Co is 1: 2 as determined by using XPS analysis, indicating that the novel catalyst reduces costs. The generation of hydrogen is schematically elucidated.     

Hydrogen production from sodium borohydride originated compounds: Fabrication of electrospun nano-crystalline Co3O4 catalyst and its activity

Electrospun nanofibers are prepared through electrospinning followed by post-treatment and preferred to use in catalytic applications. The electrospinning provides advantages for active catalysts design based on activity profiles and features of catalyst. In the present study, we fabricated nano-crystalline cobalt oxide (Co₃O₄) catalyst by electrospinning technique followed by thermal conditioning. Polyacrylonitrile (PAN) based Co as-spun mats (Co/NMs) with homogeneous diameter were prepared by electrospinnig process under several conditions as applied voltage (15–25 kV), working distance (5–7.5 cm) with the feed rate of 1 ml min⁻¹. The calcination process as a post-treatment was applied at different temperatures (232 °C, 289 °C and 450 °C) to obtain electrospun nano-crystalline Co₃O₄ catalyst. Co/NMs catalysts were characterized by XRD, SEM, TEM, XPS, FT-IR, TG/DTG, and ICP-MS techniques. The parametrically study was performed for evaluating the hydrogen production activity of catalyst from sodium borohydride (NaBH₄, SBH) and its originated compounds as ammonia borane (NH₃BH₃, AB) and methyl-amine borane (CH₃NH₂BH₃, MeAB). The relation between the internal-external properties and catalytic activities of catalysts for hydrogen production was investigated. The beadless Co/NMs-1 catalyst with homogeneous diameter was obtained under electrospinnig process conditions at 15 kV applied voltage and 7.5 cm working distance. All catalysts showed activity for hydrogen production, also the significant effect of post treatment process was observed on the catalytic activity as given order: Co/NMs-1₄₅₀ > Co/NMs-1₂₈₉ > Co/NMs-1 > Co/NMs-1₂₃₂. Furthermore, mesoporous Co₃O₄ cubic crystals (26 nm) in fibrous architecture was prepared by 450 °C-post-treatment. Hydrogen production rates were recorded at 60 °C as 2.08, 2.20, and 6.39 l H₂.g_cat⁻¹min⁻¹ for NaBH₄, CH₃NH₂BH₃, and NH₃BH₃, respectively.     

Magnetic dendritic KCC-1 nanosphere-supported cobalt composite as a separable catalyst for hydrogen generation from NaBH4 hydrolysis

The introduction of magnetism into a catalyst can greatly optimize its separation performance. In the present work, a kind of magnetically separable catalysts for promoting NaBH₄ hydrolysis have been fabricated by anchoring cobalt nanoparticles on magnetic dendritic KCC-1 nanospheres composed of magnetic Fe₃O₄ core and fibrous shell. The fabricated catalysts were characterized with various characterization methods, including absorption spectroscopy (AAS), scanning electron microscopy (SEM), high-resolution transmission electronic microscopy (HRTEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), and Fourier transform infrared (FT-IR), etc. This kind of catalysts exhibit high catalytic activity for promoting the hydrolysis of NaBH₄ under alkaline conditions, giving a hydrogen generation rate and activation energy of 3.83 L min⁻¹ g_Co⁻¹ (30 °C) and 53.63 kJ mol⁻¹, respectively. After used for 5 cycles, the catalyst showed 36.5% catalytic activity reserved. Most importantly, the magnetism of the catalyst made it easily separated and recycled from the solution after the reaction completed. The development of this kind of catalysts could provide a promising option for catalyzing NaBH₄ hydrolysis for portable hydrogen production from.     

CeO2 supported multimetallic nano materials as an efficient catalyst for hydrogen generation from the hydrolysis of NaBH4

Nowadays, there is still no suitable method to store large amounts of energy. Hydrogen can be stored physically in carbon nanotubes or chemically in the form of hydride. In this study, sodium borohydride (NaBH₄) was used as the source of hydrogen. However, an inexpensive and useful catalyst (Co–Cr–B/CeO₂) was synthesized using the NaBH₄ reduction method and its property was characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), x-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) measurements. The optimized Co–Cr–B/CeO₂ catalyst exhibited an excellent hydrogen generation rate (9182 mLg_metal⁻¹min⁻¹) and low activation energy (35.52 kJ mol⁻¹). The strong catalytic performance of the Co–Cr–B/CeO₂ catalyst is thought to be based on the synergistic effect between multimetallic nanoparticles and the effective charge transfer interactions between the metal and the support material.     

Co−O−P composite nanocatalysts for hydrogen generation from the hydrolysis of alkaline sodium borohydride solution

In recent years, catalytic hydrolysis of sodium borohydride is considered to be a promising approach for hydrogen generation towards fuel cell devices, and highly efficient and noble-metal-free catalysts have attracted increasing attention. In our present work, Co₃O₄ nanocubes are synthesized by solvothermal method, and then vapor-phase phosphorization treatment is carried out for the preparation of novel Co−O−P composite nanocatalysts composed of multiple active centers including Co, CoO, and Co₂P. For catalyst characterization, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), energy dispersive spectrometry (EDS), X-ray diffraction (XRD) and X-ray photoelectric spectroscopy (XPS) are conducted. Optimal conditions for catalyst preparation and application were investigated in detail. At room temperature (25 °C), maximum hydrogen generation rate (HGR) is measured to be 4.85 L min⁻¹ g⁻¹ using a 4 wt% NaBH₄ − 8 wt% NaOH solution, which is much higher than that of conventional catalysts with single component reported in literature. It is found that HGR remarkably increases with the increasing of reaction temperature, and apparent activation energy for catalytic hydrolysis of NaBH₄ is calculated to be 63 kJ mol⁻¹. After reusing for five times, the Co−O−P composite nanocatalysts still retains 78% of the initial activity.     

Polypyrrole supported Co–W–B nanoparticles as an efficient catalyst for improved hydrogen generation from hydrolysis of sodium borohydride

Effective and reusable catalysts with high performance are essentially necessary for NaBH₄ based on-demand hydrogen generators to the widespread use for energy conversion in fuel cell power systems. Herein, we report a facile synthesis of surfactant-directed polypyrrole-supported Co–W–B nanoparticles as a robust catalyst for efficient hydrolysis of NaBH₄ reaction. This non-noble metal catalyst provides much higher catalytic activity than a conventional cobalt boride catalyst. By incorporating tungsten to catalyst composition and tuning molar ratio of W/(Co + W), about a four-fold higher hydrogen generation rate was attained compared to bare Co–B. Among the all catalysts tested, Co–W–B/PPy with 7.5% W possessed the remarkable catalytic performance of 9.92 L min^?1 g^?1 and high stability over five cycles with the apparent activation energy of 49.18 kJ mol^?1.     

Catalytic hydrolysis of NaBH4 over titanate nanotube supported Co for hydrogen production

A Co/HTNT catalyst is developed by immobilizing Co on the surface of titanate nanotubes. The microstructure and composition of the catalyst are investigated with atomic absorption spectroscopy (AAS), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Fourier transform infrared spectrometer (FT-IR) and X-ray photoelectron spectroscopy (XPS). The developed Co/HTNT catalyst shows great performance in catalyzing NaBH₄ hydrolysis. The hydrolysis of 25 mg NaBH₄ catalyzed by 50 mg Co/HTNT in 10 g NaOH solution (12.5 wt%) provides a hydrogen production rate of 1.04 L min^?1 g_Co^?1 at 30 °C, and the activation energy of the reaction is 29.68 kJ mol^?1. The high catalytic activity and economical property make this catalyst a promising choice for on-site hydrogen production from NaBH₄ hydrolysis.     

Room temperature hydrogen generation from hydrolysis of ammonia–borane over an efficient NiAgPd/C catalyst

NiAgPd nanoparticles are successfully synthesized by in-situ reduction of Ni, Ag and Pd salts on the surface of carbon. Their catalytic activity was examined in ammonia borane (NH₃BH₃) hydrolysis to generate hydrogen gas. This nanomaterial exhibits a higher catalytic activity than those of monometallic and bimetallic counterparts and a stoichiometric amount of hydrogen was produced at a high generation rate. Hydrogen production rates were investigated in different concentrations of NH₃BH₃ solutions, including in the borates saturated solution, showing little influence of the concentrations on the reaction rates. The hydrogen production rate can reach 3.6–3.8 mol H₂ mol_cat⁻¹ min⁻¹ at room temperature (21 °C). The activation energy and TOF value are 38.36 kJ/mol and 93.8 mol H₂ mol_cat⁻¹ min⁻¹, respectively, comparable to those of Pt based catalysts. This nanomaterial catalyst also exhibits excellent chemical stability, and no significant morphology change was observed from TEM after the reaction. Using this catalyst for continuously hydrogen generation, the hydrogen production rate can be kept after generating 6.2 L hydrogen with over 10,000 turnovers and a TOF value of 90.3 mol H₂ mol_cat⁻¹ min⁻¹.     

Carbon nanotubes-promoted Co–B catalysts for rapid hydrogen generation via NaBH4 hydrolysis

In this work, multiwalled carbon nanotubes (MWCNTs) promoted Co–B catalysts for NaBH₄ hydrolysis have been designed and synthesized. The structural features of as-prepared catalysts have been investigated and discussed as a function of MWCNTs contents by X-ray diffraction, X-ray photoelectron spectra, N₂ adsorption/desorption isotherms, scanning electron microscope. The results show that the catalysts still maintain an amorphous structure with the addition of carbon nanotubes promoter. However, the appropriate amount of MWCNTs promoter in Co–B catalysts leads to large specific surface area, fine dispersion of active components, increased active sites and high electron density at active sites. Moreover, hydrogen spillover on the catalyst is promoted, which contributes to regeneration of active sites and accelerating catalytic cycle. Among all the experimental samples, it is found that the Co–B catalyst promoted by 10 wt% carbon nanotubes exhibits optimal catalytic activity with remarkably high hydrogen generation rate of 12.00 L min⁻¹·g_catalyst⁻¹ and relatively good stability.     

Poly(2-aminoethyl methacrylate) based microgels catalyst system to be used in hydrolysis and methanolysis of NaBH4 for H2 generation

The poly(2-aminoethyl methacrylate) (p(AEM)) microgels were synthesized by microemulsion polymerization technique and used for in situ metal nanoparticle preparation to render as p(AEM)-M (M: Co or Ni) microgel composites and were used in p(AEM) based poly ionic liquid (PIL) microgels. Next, these p(AEM)) based microgel materials were used as catalysts for hydrogen (H₂) production from both hydrolysis and methanolysis reactions of sodium borohydride (NaBH₄). It was found that the catalytic hydrolysis of the NaBH₄ reaction, catalyzed by p(AEM)-Co microgel composite was completed in 140 min, whereas the methanolysis of NaBH₄ methanolysis catalyzed by the PIL of p(AEM)⁺Cl⁻ microgels was completed in 5 min both with 250 ± 2 mL H₂ production. Furthermore, p(AEM)-Co microgel composite catalysts maintained 80% catalytic activity after 5 consecutive uses in NaBH₄ hydrolysis. On the other hand, p(AEM)⁺Cl⁻ microgels were found to afford more than 50% catalytic activity even after 20 repetitive use in NaBH₄ methanolysis due to superior regeneration ability. Moreover, activation energy values for p(AEM)-Co microgel composites catalyzed NaBH₄ hydrolysis reaction were calculated as 38.9 kJ/mol in comparison to 37.3 kJ/mol activation energy of p(AEM)⁺Cl⁻ microgel catalyzed methanolysis reaction.     

Spirulina Platensis microalgae strain modified with phosphoric acid as a novel support material for Co–B catalysts: Its application to hydrogen production

Spirulina platensis is defined as the dried biomass of cyanobacteria in commercial use and is biomass with high carbon content. Spirulina platensis microalgae strain supported-CoB catalysts to produce hydrogen from sodium borohydride (NaBH₄) were prepared for the first time. The Spirulina platensis microalgae strain was modified with phosphoric acid (H₃PO₄) to proton. Then, the supported catalyst was performed to produce hydrogen from NaBH₄ hydrolysis. The optimum H₃PO₄ concentration, optimum Co amount, and optimum impregnation time of the H₃PO₄ with the microalgae strain were investigated. The maximum hydrogen production rate for the 30% CoB catalyst supported on microalgae strain treated with H₃PO₄ was found to be 3940 mL min⁻¹g⁻¹catalyst. X-ray powder diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Brunauer–Emmett–Teller (BET), and scanning electron microscope (SEM) analysis were performed for characterization of CoB catalyst supported on Spirulina microalgae strain. After four consecutive uses, the performance and conversion values of this catalyst were investigated. At the same time, the effect of temperature on the hydrogen production from this hydrolysis reaction was examined. The activation energy with the CoB catalyst supported on Spirulina microalgae strain was calculated as 35.25 kJ mol⁻¹. According to the kinetic model of a power law, n value was found as 0.25 for kinetic studies.     

Investigation of hydrogen generation from sodium borohydride using different cobalt catalysts

Effective Co/Cu, CoB/Cu, and CoBM (M = Mo,Zn,Fe)/Cu catalysts were prepared on the copper surface by a simple electroless deposition method using a morpholine borane as a reducing agent in the glycine solution. The activity of the deposited catalysts was investigated for hydrogen generation from an alkaline sodium borohydride solution. It was determined that these synthesized catalysts demonstrated the catalytic activity for the hydrolysis reaction of NaBH₄. The lowest obtained activation energy (E_A) of the hydrolysis reaction of NaBH₄was 27 kJ mol^?1 for the CoBMo/Cu catalyst. The hydrogen generation rate of 15.30 ml min^?1 was achieved using CoBMo/Cu catalysts at 313 K and it increased ~3.5 times with the increase of temperature to 343 K. The highest hydrogen generation rate obtained by CoBMo/Cu films may be related to the hierarchical cauliflower-shaped 3D structures and the high roughness surface area. Moreover, the CoBMo/Cu catalyst showed an excellent reusability.     

The use of metallurgical waste sludge as a catalyst in hydrogen production from sodium borohydride

In this study, the metallurgic sludge which contained oil and was obtained as waste of grinding, sharpening and milling parts was used in the production of hydrogen (H₂) from sodium borohydride (NaBH₄). The hydrolysis of NaBH₄ with the metallurgic sludge catalyst was investigated depending on several parameters such as sodium hydroxide (NaOH) concentration, catalyst amount, NaBH₄ concentration and temperature. The obtained metallurgic sludge catalyst was characterized by the XRD, FT-IR and SEM techniques and was evaluated for its activity in the H₂ generation from NaBH₄ hydrolysis. The maximum H₂ production rate from the hydrolysis of NaBH₄ with the metallurgic sludge catalyst was calculated as 9366 ml min⁻¹.g_cat⁻¹. The value of activation energy was found as 48.05 kJ mol⁻¹.     

Multifunctional Co–B–O@CoxB catalysts for efficient hydrogen generation

The development of efficient and non-noble catalyst is of great significance to hydrogen generation techniques. Three surface-oxidized cobalt borides of Co–B–O@Co_xB (x = 0.5, 1 and 2) have been synthesized that can functionalize as active catalysts in both alkaline water electrolysis and the hydrolysis of sodium borohydride (NaBH₄) solution. It is discovered that oxidation layer and low boron content favor the oxygen evolution reaction (OER) activity of Co–B–O@Co_xB in alkaline water electrolysis. And surface-oxidized cobalt boride with low boron content is more active toward hydrolysis of NaBH₄ solution. An alkaline electrolyzer fabricated using the optimized electrodes of Co–B–O@CoB₂/Ni as cathode and Co–B–O@Co₂B/Ni as anode can deliver current density of 10 mA cm⁻² at 1.54 V for overall water splitting with satisfactory stability. Meanwhile, Co–B–O@Co₂B affords the highest hydrogen generation rate of 3.85 L min⁻¹ g⁻¹ for hydrolysis of NaBH₄ at 25 °C.     

Effects of structure on the carbon dioxide methanation performance of Co-based catalysts

Mesoporous Co/KIT-6 and Co/meso-SiO₂ catalysts were prepared via hydrogen reduction and were subsequently used in CO₂ catalytic hydrogenation to produce methane. The properties of these catalysts were investigated via low-angle X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, and transmission electron microscopy (TEM). The results indicate that the synthesized Co/KIT-6 and Co/meso-SiO₂ catalysts have mesoporous structures with well-dispersed Co species, as well as high CO₂ catalytic hydrogenation activities. The Co/KIT-6 catalyst has a large specific surface area (368.9 m² g⁻¹) and a highly ordered bicontinuous mesoporous structure. This catalyst exhibits excellent CO₂ catalytic hydrogenation activity and methane product selectivity, which are both higher than those of the Co/meso-SiO₂ catalyst at high reaction temperatures. The CO₂ conversion and methane selectivity of the Co/KIT-6 catalyst at 280 °C are 48.9% and 100%, respectively. The high dispersion of the Co species and the large specific surface area of the prepared Co-based catalysts contribute to the high catalytic activities. In addition, the highly ordered, bicontinuous, mesoporous structure of the Co/KIT-6 catalyst improves the selectivity for the methane product.     

Metal-organic frameworks (MOFs) and MOFs-derived CuO@C for hydrogen generation from sodium borohydride

Hydrogen gas has been considered as one of the promising sources of energy. Thus, several strategies including the hydrolysis of hydrides have been reported for hydrogen production. However, effective catalysts are highly required to improve the hydrogen generation rate. Two dimensional metal-organic frameworks (copper-benzene-1,4-dicarboxylic, CuBDC), and CuBDC-derived CuO@C were synthesized, characterized and applied as catalysts for hydrogen production using the hydrolysis and methanolysis of sodium borohydride (NaBH₄). CuBDC, and CuO@C display hydrogen generation rate of 7620, and 7240 mlH₂·g_cat⁻¹· min⁻¹, respectively for hydrolysis. While, CuBDC offers hydrogen generation rate of 9060 mlH₂·g_cat⁻¹· min⁻¹ for methanolysis. Both catalysts required short reaction time, and showed good recyclability. The materials may open new venues for efficient catalyst for energy-based applications.     

Optimisation of sepiolite clay with phosphoric acid treatment as support material for CoB catalyst and application to produce hydrogen from the NaBH4 hydrolysis

Herein, the CoB catalyst supported on the sepiolite clay treated with phosphoric acid was utilized to produce hydrogen from the NaBH₄ hydrolysis. In order to analyse the performance of the phosphoric acid treated sepiolite clay supported-CoB catalyst, the NaBH₄ concentration effect, phosphoric acid concentration effect, phosphoric acid impregnation time effect, CoB catalyst percentage effect, and temperature effect were studied. In addition, XRD, XPS, SEM, TEM, BET, and FTIR analysis were performed for characterization of Co–B catalyst supported on the acid-treated sepiolite. The completion time of this hydrolysis reaction with Co–B (20%) catalyst supported on the sepiolite treated by 5 M phosphoric acid was approximately 80 min, whereas the completion time of this hydrolysis reaction with acid-free sepiolite-supported Co–B (20%) catalyst was approximately 260 min. There is a five-fold increase in the maximum production rate. The maximum hydrogen production rates of this hydrolysis reaction at 30 and 60 °C were found as 1486 and 5025 ml min⁻¹g⁻¹_catalyst, respectively. Activation energy was found as 21.4 kJ/mol. This result indicates that the acid treatment on sepiolite is quite successful. The re-usability of NaBH₄ hydrolysis reaction by CoB catalyst supported on sepiolite treated phosphoric acid for successive five cycles of NaBH₄ at 30 °C was investigated.