Experimental investigation on hydrogen production by methanol steam reforming in a novel multichannel micro packed bed reformer

A novel multichannel micro packed bed reactor with bifurcation inlet manifold and rectangular outlet manifold was developed to improve the methanol steam reforming performance in this study. The commercial CuO/ZnO/Al₂O₃ catalyst particles were directly packed in the reactor. The flow distribution uniformity in the reactor was optimized numerically. Experiments were conducted to study the influences of steam to carbon molar ratio (S/C), weight hourly space velocity (WHSV), reactor operating temperature (T) and catalyst particle size on the methanol conversion rate, H₂ production rate, CO concentration in the reformate, and CO₂ selectivity. The results show that increase of the S/C and T, as well as decrease of the WHSV and catalyst particle size, both enhance the methanol conversion. The CO concentration decreases as the S/C and WHSV increase as well as the T and catalyst particle size decrease. Moreover, T plays a more important role on the methanol steam reforming performance than WHSV and S/C. The impacts on CO concentration become insignificant when the S/C is higher than 1.3, WHSV is larger than 1.34 h⁻¹ and T is lower than 275 °C. A long term stability test of this reactor was also performed for 36 h and achieved high methanol conversion rate above 94.04% and low CO concentration less than 1.05% under specific operating conditions.     

Experiments on hydrogen production from methanol steam reforming in the microchannel reactor

The entire experiments were conducted for microchannel methanol steam reforming, by which, the selection of catalyst, the operating parameters and the configuration of microchannels were discussed thoroughly. It was found that the higher the Cu concentration is, the more the corresponding active surface area of Cu will be, thereby improving the catalytic activity. The Cu-to-Zn ratio in Cu/ZnO/Al₂O₃ catalyst should be set at 1:1. The impacts of reaction temperature, feed flow rate, mixture temperature, and H₂O-to-CH₃OH molar ratio on the methanol conversion rate were also revealed and discussed. Characteristics of micro-reactors with various microchannels, including that 20 mm and 50 mm in length, as well as non-parallel microchannels, were investigated. It was found that the increase of microchannel length can improve the methanol conversion rate significantly. Besides, non-parallel microchannels help to maintain flow and temperature distribution uniformity, which can improve the performance of micro-reactor. In the present experiments, the presence of CO was under the condition that the methanol conversion rate was above 70%.     

Experiments on hydrogen production from methanol steam reforming in fluidized bed reactor

A novel approach for the hydrogen production which integrated methanol steam reforming and fluidized bed reactor (FBR) was proposed. The reaction was carried out over Cu/ZnO/Al₂O₃ catalysts. The critical fluidized velocities under different catalyst particle sizes and masses were obtained. The influences of the operating parameters, including that of H₂O-to-CH₃OH molar ratio, feed flow rate, reaction temperature, and catalyst mass on the performance of methanol steam reforming were investigated in FBR to obtain the optimum experimental conditions. More uniform temperature distribution, larger surface volume ratio and longer contacting time can be achieved in FBR than that in fixed bed reactor. The results indicate that the methanol conversion rate in FBR can be as high as 91.95% while the reaction temperatures is 330 °C, steam-to-carbon molar ratio is 1.3, and feed flow rate is 540 ml/h under the present experiments, which is much higher than that in the fixed bed.     

Recent trends in the development of reactor systems for hydrogen production via methanol steam reforming

Hydrogen is currently receiving significant attention as an alternative energy resource, and among the various methods for producing hydrogen, methanol steam reforming (MSR) has attracted great attention because of its economy and practicality. Because the MSR reaction is inherently activated over catalytic materials, studies have focused on the development of noble metal-based catalysts and the improvement of existing catalysts with respect to performance and stability. However, less attention has been paid to the modification and development of innovative MSR reactors to improve their performance and efficiency. Therefore, in this review paper, we summarize the trends in the development of MSR reactor systems, including microreactors and membrane reactors, as well as the various structured catalyst materials appropriate for application in complex reactors. In addition, other engineering approaches to achieve highly efficient MSR reactors for the production of hydrogen are discussed.     

Mathematical simulation of hydrogen production via methanol steam reforming using double-jacketed membrane reactor

The hydrogen production and purification via methanol reforming reaction was studied in a double-jacketed Pd membrane reactor using a 1-D, non-isothermal mathematical model. Both mass and heat transfer behavior were evaluated simultaneously in three parts of the reactor, annular side, permeation tube and the oxidation side. The simulation results exhibited that increasing the volumetric flow rate of hydrogen in permeation side could enhance hydrogen permeation rate across the membrane. The optimum velocity ratio between permeation and annular sides is 10. However, hydrogen removal could lower the temperature in the reformer. The hydrogen production rate increases as temperature increases at a given Damköhler number, but the methanol conversion and hydrogen recovery yield decrease. In addition, the optimum molar ratio of air and methanol was 1.3 with three air inlet temperatures. The performance of a double-jacketed membrane reactor was compared with an autothermal reactor by judging against methanol conversion, hydrogen recovery yield and production rate. Under the same reaction conditions, the double-jacketed reactor can convert more methanol at a given reactor volume than that of an autothermal reactor.     

Performance assessment and evaluation of catalytic membrane reactor for pure hydrogen production via steam reforming of methanol

The steam reforming of methanol was investigated in a catalytic Pd–Ag membrane reactor at different operating conditions on a commercial Cu/ZnO/Al₂O₃ catalyst. A comprehensive two-dimensional non-isothermal stationary mathematical model has been developed. The present model takes into account the main chemical reactions, heat and mass transfer phenomena in the membrane reactor with hydrogen permeation across the PdAg membrane in radial direction. Model validation revealed that the predicted results satisfy the experimental data reasonably well under the different operating conditions. Also the impact of different operating parameters including temperature, pressure, sweep ratio and steam ratio on the performance of reactor has been examined in terms of methanol conversion and hydrogen recovery. The modeling results have indicated the high performance of the membrane reactor which is related to continuous removal of hydrogen from retentate side through the membrane to shift the reaction equilibrium towards formation of hydrogen. The obtained results have confirmed that increasing the temperature improves the kinetic properties of the catalyst and increase in the membrane's H₂ permeance, which results in higher methanol conversion and hydrogen production. Also it is inferred that the hydrogen recovery is favored at higher temperature, pressure, sweep ratio and steam ratio. The model prediction revealed that at 573 K, 2 bar and sweep ratio of 1, the maximum hydrogen recovery improves from 64% to 100% with increasing the steam ratio from 1 to 4.     

A performance study of methanol steam reforming in an A-type microchannel reactor

The methanol steam reforming (MSR) performance in a microchannel reactor is directly related to the flow pattern design of the microchannel reactor. Hydrogen production improvements can be achieved by optimal design of the flow pattern. In this study, an A-type microchannel reactor with a flow pattern design of one inlet and two outlets was applied to conduct the MSR for hydrogen production. The MSR performance of the A-type microchannel reactor was investigated through numerical analysis by establishing a three-dimensional simulation model and compared with that of the conventional Z-type microchannel reactor. Experiments were also conducted to test the MSR performance and validate the accuracy of the simulation model. The results showed that compared with the conventional Z-type microchannel reactor, the species distributions in the A-type microchannel reactor were more homogeneous. In addition, compared with the Z-type microchannel reactor, the A-type microchannel reactor was shown to effectively increase the methanol conversion rate by up to 8% and decrease the pressure drop by about 20%, regardless of a slightly higher CO mole fraction. It was also noted that with various quantities of microchannels and microchannel cross sections, the A-type microchannel reactor was still more competitive in terms of a higher methanol conversion rate and a lower pressure drop.     

Theoretical evaluation of various configurations of silica membrane reactor in methanol steam reforming using CFD method

The main purposes of this work was to evaluate from a theoretical point of view the performance of silica membrane reactors (MRs) in various configurations for generating hydrogen via methanol steam reforming (MSR) reaction using a two dimensional computational fluid dynamic (CFD) method, presenting details about molar fractions of gas species, velocity and pressure distributions at the simulated conditions. The CFD model was firstly validated and, then, used for the simulations, achieving an acceptable agreement between numerical outcomes and experimental data. The simulations were realized for MSR reaction carried out in three types of silica MRs, namely: 1) silica MR with cocurrent flow pattern (MR1); 2) silica MR with countercurrent flow pattern (MR2); 3) silica MR with countercurrent flow pattern including a water gas shift (WGS) reaction stage in the permeate side (MR3), meanwhile comparing the results with a traditional reactor (TR). The influence of several operating parameters (reaction temperature and pressure, and feed flow rate) on the performance of the aforementioned silica MRs in terms of methanol conversion, hydrogen yield and CO-selectivity was evaluated and the results compared with an equivalent TR. The simulations via CFD method indicated the MR3 results to be the best solution over the other MR proposed configurations and the TR as well, presenting the best simulation results at 10 bar of transmembrane pressure, 513 K, SF = 6, GHSV = 6000 h⁻¹ and feed molar ratio = 3/1 with CO selectivity ≤0.04%, methanol conversion and hydrogen yield >90%.     

Co-current and counter-current modes for methanol steam reforming membrane reactor

In this simulation study, methanol steam reforming reaction to produce synthesis gas has been studied in a membrane reactor when shell side and lumen side streams are in co-current mode or in counter-current mode. The simulation results for both co-current and counter-current modes are presented in terms of methanol conversion and molar fraction versus temperature, pressure, _H2O/_CH3OH${\mathrm{H}}_2\mathrm{O}/{\mathrm{CH}}_3\mathrm{OH}$ molar feed flow rate ratio and axial co-ordinate.     

Experimental evaluation of methanol steam reforming reactor heated by catalyst combustion for kW-class SOFC

The distributed power generation of methanol steam reforming reactor combined with solid oxide fuel cell (SOFC) has the characteristics of outstanding economic advantages. In this paper, a methanol steam reforming reactor was designed which integrates catalyst combustion, vaporization and reforming. By catalyst combustion, it can achieve stable operation to supply fuel for kW-class SOFC in real time without additional heating equipment. The optimal operating condition of the reforming reactor is 523–553 K, and the steam to carbon ratio (S/C) is 1.2. To study the reforming performance, methanol steam reforming (MSR), methanol decomposition (MD), water-gas shift (WGS) were considered. Operating temperature is the greatest factor affecting reforming performance. The higher the reaction temperature, the lower the H₂ and CO₂, the higher the CO and the methanol conversion rate. The methanol conversion rate is up to 95.03%. The higher the liquid space velocity (LHSV), the lower the methanol conversion rate, the lowest is 90.7%. The temperature changes of the reforming reactor caused by the load change of stack takes about 30 min to reach new balance. Local hotspots within the reforming reactor lead to an excessive local temperature to test a small amount of CH₄ in the reforming gas. The methanation reaction cannot be ignored at the operating temperature. The reforming gas contains 70–75% H₂, 3–8% CO, 18–22% CO₂ and 0.0004–0.3% CH₄. Trace amounts of C₂H₆ and C₂H₄ are also found in some experiments. The reforming reactor can stably supply the fuel for up to 1125 W SOFC.     

Evaluation of silica membrane reactor performance for hydrogen production via methanol steam reforming: Modeling study

The aim of this work is to analyze the potential application of microporous silica membrane reactor carrying out methanol steam reforming reaction for hydrogen production. As a further study, a comparison with dense Pd–Ag membrane reactor and a traditional reactor, working at the same operating conditions of silica membrane reactor, is realized.     

H2 production in silica membrane reactor via methanol steam reforming: Modeling and HAZOP analysis

The main aim of this work is the presentation of both qualitative safety and quantitative operating analyses of silica membrane reactor (MR) for carrying out methanol steam reforming (MSR) reaction to produce hydrogen. To perform the safety analysis, HAZOP method is used. Before the HAZOP analysis, a comprehensive investigation of most important operating parameters effects on silica MR performance is required. Therefore, for a quantitative analysis, a 1-dimensional and isothermal model is developed for evaluating the reaction temperature, reaction pressure, feed molar ratio (steam/methanol) and feed flow rate effects on silica MR performance in terms of methanol conversion and hydrogen recovery. The model validation results show good agreement with experimental data from literature. As a consequence, simulation results indicate that the reaction pressure and feed molar ratio have dual effect on silica MR performance. In particular, it is found that methanol conversion is decreased by increasing the reaction pressure from 1.5 to 4.0 bar, whereas over 4.0 bar, it is improved. Moreover, the hydrogen recovery is decreased by increasing the feed molar ratio from 1 to 5, while over 5, it was approximately constant. After the evaluation of modeling results, the HAZOP analysis for silica MR is carried out during MSR reaction. The analysed operating parameters in the modeling study have been considered as key parameters in the HAZOP analysis. The safety assessment results are presented in tables as check list. By considering the HAZOP results, safety pretreatment works are recommended before or during the experimental tests of MSR reaction in silica MR. According to different parameters consequences, reaction temperature is the most critical parameter in MSR reaction for the silica MR studied in this work. In particular, to avoid the consequences of temperature deviation, it is recommended to use a PID temperature controller in the silica MR for MSR reaction.     

Techno-economic and environmental assessment of methanol steam reforming for H2 production at various scales

According to global trend of transition to a hydrogen society, needs for alternative hydrogen (H₂) production methods have been on the rise. Among them, methanol steam reforming (MSR) in a membrane reactor (MR) has received a great attention due to its improved H₂ yield and compact design. In this study, 3 types of economic analysis – itemized cost estimation, sensitivity analysis, and uncertainty analysis – and integrative carbon footprint analysis (iCFA) were carried out to investigate economic and environmental feasibility. Unit H₂ production costs of MSR in a packed-bed reactor (PBR) and an MR for various H₂ production capacities of 30, 100, 300, and 700 m³ h⁻¹ and CO₂ emission rates for both a PBR and an MR in H₂ production capacity of 30 m³ h⁻¹ were estimated. Through itemized cost estimation, unit H₂ production costs of a PBR and an MR were obtained and scenario analysis was carried out to find a minimum H₂ production cost. Sensitivity analysis was employed to identify key economic factors. In addition, comprehensive uncertainty analysis reflecting unpredictable fluctuation of key economic factors of reactant, labor, and natural gas obtained from sensitivity analysis was also performed for a PBR and an MR by varying them both simultaneously and individually. Through iCFA, lowered CO₂ emission rates were obtained showing environmental benefit of MSR in an MR.     

Comparison between 1D and 2D numerical models of a multi-tubular packed-bed reactor for methanol steam reforming

The hydrogen-rich gas produced in-situ by methanol steam reforming (MSR) reactions significantly affects the performance and endurance of the high-temperature polymer electrolyte membrane (HT-PEM) fuel cell stack. A numerical study of MSR reactions over a commercial CuO/ZnO/Al₂O₃ catalyst coupling with the heat and mass transfer phenomena in a co-current packed-bed reactor is conducted. The simulation results of a 1D and a 2D pseudo-homogeneous reactor model are compared, which indicates the importance of radial gradients in the catalyst bed. The effects of geometry and operating parameters on the steady-state performance of the reactor are investigated. The simulation results show that the increases in the inlet temperature of burner gas and the tube diameter significantly increase the non-uniformity of radial temperature distributions in reformer tubes. Hot spots are formed near the tube wall in the entrance region. The hot-spot temperature in the catalyst bed rises with the increase in the inlet temperature of burner gas. Moreover, the difference in simulation results between the 1D and 2D models is shown to be primarily influenced by the tube diameter. With a methanol conversion approaching 100% or a relatively small tube diameter, the simplified 1D model can be used instead of the 2D model to estimate the reactor performance.     

Methanol steam reforming in a microchannel reactor by Zn-, Ce- and Zr- modified mesoporous Cu/SBA-15 nanocatalyst

Hydrogen production by steam reforming of methanol was studied over several Cu/SAB-15-based nanocatalysts in a parallel-type microchannel reactor. The catalysts were prepared through impregnation method and XRD, BET, FT-IR, FE-SEM, TEM, H₂-TPR and TGA techniques were used to characterize surface and structural properties of the synthesized catalysts. The effects of reaction temperature, WHSV and S/C molar ratio on the methanol conversion and selectivities of the gaseous products were studied. Then, effects of the metallic promoters were investigated to improve performance of the catalysts. It was revealed that ZnO and CeO₂ promoters have positive effects on decreasing CO selectivity and ZrO₂ promotes methanol conversion. Furthermore, ZrO₂ and CeO₂ were declared to improve stability of the catalyst. Among the evaluated catalysts, Cu/ZnO/CeO₂/ZrO₂/SBA-15 can provide optimal methanol conversion with low CO concentration in the gaseous products. For this catalyst, the methanol conversion and hydrogen selectivity reached 95.2% and 94.6%, respectively.     

Investigation of a methanol processing system comprising of a steam reformer and two preferential oxidation reactors for fuel cells

Methanol steam reforming is able to produce hydrogen-rich syngas onsite for fuel cells and avoids the problems of hydrogen storage. Nevertheless, CO in the reformate needs to be further removed to ppm level before it can be fed into proton exchange membrane fuel cells. In this study, a methanol processing system consisting of a methanol reformer and two-stage preferential oxidation reactors is developed. The hydrogen production performance and scalability of the reformer are experimentally investigated under various operating conditions. The methanol reformer system shows stable methanol conversion rate and linearly increased H₂ flow rate as the number of repeating unit increases. Methanol conversion rate of 96.8% with CO concentration of 1.78% are achieved in the scaled-up system. CO cleanup ability of the two-stage preferential oxidation reactors is experimentally investigated based on the reformate compositions by varying the operating temperature and O₂ to CO ratios. The results demonstrate that the developed CO cleanup train can decrease the CO concentration from 1.6% to below 10 ppm, which meets the requirement of the fuel cell. Finally, stability of the integrated methanol processing system is tested for 180 h operation.     

A transient study of double-jacketed membrane reactor via methanol steam reforming

A non-isothermal unsteady-state model was established to simulate methanol steam reforming using a double-jacketed Pd membrane reactor. At steady state, a self-sustained membrane reactor was achieved by the oxidation of residual methanol and hydrogen from reformer for endothermic steam reforming. The molar fractions of species and reformer temperature were analyzed under co-current operation between oxidation and reformer sides. The start-up of reformer was simulated under two conditions: (1) The catalyst temperature was lower than the influent temperature and (2) The catalyst temperature was higher than influent temperature. Condition 1 yielded higher methanol conversion and reformer temperature than condition 2 at steady state. Moreover, the instability of species can be minimized on condition 1 during start-up. The fluctuation of membrane reactor at steady state was also studied. Two strategies were compared to analyze the reformer response when temporary extra hydrogen was required. The results showed that increasing inlet methanol outperformed increasing reformer temperature.     

Numerical analysis of methanol steam reforming reactor heated by catalytic combustion for hydrogen production

Thermal coupling of endothermic and exothermic reactions is an important pathway for integrated thermal management within a methanol steam reforming reactor heated by methanol catalytic combustion. In this study, a numerical model is developed for heat and mass transfer calculations, methanol steam reforming and catalytic combustion reactions, which is used to explore the effects of design parameters on compact parallel channel reactor performance. Efficiency of the integrated reactor is optimized by the coupling of endothermic and exothermic reactions using conventional wall material. Temperature uniformity is improved by the adjustment of the flow arrangement and the catalyst distribution. This work provides an effective energy management strategy and tool which can be adopted in the design of portable hydrogen generation systems.     

Microwave-activated methanol steam reforming for hydrogen production

Methanol steam reforming (MSR) was carried out in a catalytic packed bed reactor under electrical and microwave heating using the two most common catalysts for this process-CuZnO/Al₂O₃ and PdZnO/Al₂O₃. Significant two-dimensional temperature gradients were found, especially in the latter case. Our results show that for the same average bed temperature, methanol conversion is higher under microwave heating (>10%). On the other hand, the product distribution is not affected by the heating mode. We demonstrate that even in cases where the maximum temperature along the entire height of the bed is significantly higher under electrical heating, conversion is either higher in the microwave case or approximately the same between the two heating modes. Finally, our experimental data indicate that a given methanol conversion can be achieved with lower net heat input to the reactor under microwave heating. This does not mean lower total energy consumption in the microwave process due to the limitations in the magnetron efficiency and the reflected power. However, it may be an implicit indication of higher temperature at metal sites than in bulk phase (microscale hot spot formation) due to the selective heating principle.