High power CW diode-side-pumped Nd:YAG rod laser

We report on the characterization of a diode-side-pumped Nd:YAG rod laser operating at high CW output power. A four-fold pump configuration is designed and the pump light is directly coupled into the Nd:YAG rod without the help of any cylindrical lenses. The distribution of pump light in the Nd:YAG rod has been calculated by using ray tracing program. The thermal lens effect of the Nd:YAG rod has been experimentally measured. A maximum output power of 800 W at 1064 nm in multimode operation is obtained for a pump power of 2400 W with 33% optical-optical efficiency. At the same time, the maximum beam parameter product of 25 mm·mrad is achieved.     

Highly efficient diode side-pumped Nd:YAG ceramic laser with 210 W output power

We developed a highly efficient diode side-pumped Nd:YAG ceramic laser with a diffusive reflector as an optical pump cavity. A maximum output power of 211.6 W was obtained with an optical-to-optical conversion efficiency of 48.7%. This corresponds to the highest conversion efficiency in the side-pumped ceramic rod. Thermal effects of the Nd:YAG ceramic rod were analyzed in detail through the measurements of laser output powers and beam profiles near the critically unstable region. A M² beam quality factor of 18.7 was obtained at the maximum laser output power.     

Side-pumped continuous-wave Cr:Nd:YAG ceramic solar laser

To clarify the advantages of Cr:Nd:YAG ceramics rods in solar-pumped lasers, a fused silica light guide with rectangular cross-section is coupled to a compound V-shaped cavity within which a 7 mm diameter 0.1 at.% Cr:1.0 at.% Nd:YAG ceramic rod is uniformly pumped. The highly concentrated solar radiation at the focal spot of a 2 m diameter stationary parabolic mirror is transformed into a uniform pump radiation by the light guide. Efficient pump light absorption is achieved by pumping uniformly the ceramic rod within the V-shaped cavity. Optimum pumping parameters and solar laser output powers are found through ZEMAX^© non-sequential ray-tracing and LASCAD^© laser cavity analysis codes. 33.6 W continuous-wave laser power is measured, corresponding to 1.32 times enhancement over our previous results with a 4 mm diameter Nd:YAG single-crystal rod. High slope efficiency of 2.6 % is also registered. The solar laser output performances of both the ceramic and the single-crystal rods are finally compared, revealing the relative advantage of the Cr:Nd:YAG rod in conversion efficiency. Low scattering coefficient of 0.0018 cm^?1 is deduced for the ceramic rod. Heat load is considered as a key factor affecting the ceramic laser output performance.     

1.15 kW连续波全固态Nd:YAG激光器

研制了五组双线二极管列阵侧面泵浦Nd: YAG棒的高效率、高功率激光头。将一块90° 石英旋光片插入两个这样的激光头中间并置入热近非稳对称平平腔，产生了1157 W高光束质量（M2 ~ 39）1064 nm连续波输出，据我们所知，这是侧面泵浦双棒Nd: YAG激光器产生的最高功率。     

High-power and high optical conversion efficiency diode-end-pumped laser with multi-segmented Nd:YAG/Nd:YVO_4

A novel flat-flat resonator consisting of two crystals(Nd:YAG + Nd:YVO_4) is established for power scaling in a diode-end-pumped solid-state laser. We systematically compare laser characteristics between multi-segmented(Nd:YAG + Nd:YVO_4) and conventional composite(Nd:YAG + Nd:YAG) crystals to demonstrate the feasibility of spectral line matching for output power scale-up in end-pumped lasers. A maximum continuous-wave output power of 79.2 W is reported at 1064 nm, with M_x~2= 4.82, M_y~2= 5.48, and a pumping power of 136 W in the multi-segmented crystals(Nd:YAG + Nd:YVO_4). Compared to conventional composite crystals(Nd:YAG + Nd:YAG), the optical-optical conversion efficiency of multi-segmented crystals(Nd:YAG + Nd:YVO4) from 808 nm to 1064 nm is enhanced from 30% to 58.8%,while the laser output sensitivity as affected by the diode-laser temperature is reduced from 55% to 9%.     

LD侧泵Nd∶YAG/S-KTP腔内倍频高功率660nm连续红光激光器

报道了LD侧面泵浦Nd∶YAG/S-KTP腔内倍频高功率660nm连续红光激光器。泵浦组件（呈三角形等间距分布）由9个20W的激光二极管组成，最大泵浦功率为180W。通过对谐振腔参数进行优化设计，用LD连续抽运3mm×65mm Nd∶YAG激光棒时，获得了波长为1319nm的基频光振荡。利用S-KTP II类临界相位匹配腔内倍频技术，当泵浦电流为22A时，获得了6.8W的连续红光激光输出，光-光转换效率为4.3％。     

A high-power high-stability Q-switched green laser with intracavity frequency doubling using a diode-pumped composite ceramic Nd：YAG laser

We successfully obtain a high-average-power high-stability Q-switched green laser based on diode-side-pumped composite ceramic Nd:YAG in a straight plano-concave cavity. The temperature distribution in composite ceramic Nd:YAG crystal is numerically analyzed and compared with that of conventional Nd:YAG crystal. By using a composite ceramic Nd:YAG rod and a type-II high gray track resistance KTP (HGTR-KTP) crystal, a green laser with an average output power of 165 W is obtained at a repetition rate of 25 kHz, with a diode-to-green optical conversion of 14.68%, and a pulse width of 162 ns. To the best of our knowledge, both the output power and optical-to-optical efficiency are the highest values for green laser systems with intracavity frequency doubling of this novel composite ceramic Nd:YAG laser to date. The power fluctuation at around 160 W is lower than 0.3% in 2.5 hours.     

High-power high-stability Q-switched green laser with intracavity frequency doubling of diode-pumped composite ceramic Nd:YAG laser

We successfully obtain high-average-power high-stability Q-switched green laser based on diode-side-pumped composite ceramic Nd:YAG in a straight plano-concave cavity. The temperature distribution in composite ceramic Nd:YAG crystal is numerically analyzed and compared with that of conventional Nd:YAG crystal. By use of a composite ceramic Nd:YAG rod and a type-II high gray track resistance KTP (HGTR-KTP) crystal, a green laser with an average output power of 165 W is obtained at a repetition rate of 25 kHz, with a diode-to-green optical conversion of 14.68%, and a pulse width of 162 ns. To the best of our knowledge, both the output power and optical-to-optical efficiency are the highest values for green laser systems with intracavity frequency doubling of this novel composite ceramic Nd:YAG laser to date. The power fluctuation at around 160 W is lower than 0.3% in 2.5 hours.     

Continuous-wave, 15.2 W diode-end-pumped Nd:YAG laser operating at 946 nm

A high-power continuous-wave (cw) Nd:YAG laser operating at 946 nm by utilizing a quasi-three-level transition is reported. The laser consists of a composite Nd:YAG rod end pumped by a fiber-coupled diode laser and a simple plane-concave cavity. At an incident pump power of 40.2 W, a maximum cw output of 15.2 W at 946 nm is obtained, achieving a slope efficiency of 45%. To the best of our knowledge, this is the highest output at 946 nm ever generated by diode-pumped Nd:YAG lasers. In addition, at an incident pump power of 15.2 W, a 1.25 W blue output at 473 nm is achieved with a simple compact three-element cavity and a type-I lithium triborate (LiB(3)O(5)) crystal as a frequency doubler.     

Single rod efficient Nd:YAG and Nd:YALO lasers with average output powers of 46 and 47 W in diffraction limited beams with M<1.2 and 100 W with M<3.7

Using a new resonator concept guaranteeing fundamental mode operation, flashlamp pumped Nd lasers with average output powers of 46 and 47 W for the two materials were realized with beam qualities better than 1.2*DL. Due to the absence of thermally induced birefringence the efficiency of the Nd:YALO laser was up to 1.85% and thus 1.5 times higher than that of the realized Nd:YAG laser. The Nd:YALO laser output is linear polarized. Average output power of 100 W could be extracted from a Nd:YAG single rod oscillator with a beam quality of better than 3.7×DL.     

High efficiency,high power QCW diode-side-pumped Nd：YAG ceramic laser at 1064 nm based on domestic ceramic

A high efficiency, high power diode-side-pumped quasi continuous wave （QCW） Nd：YAG ceramic rod laser at 1064 nm based on the domestic transparent ceramic is reported. The average output power of 961 W is achieved with double ceramic rods by means of a symmetrical convex-convex cavity. The optical-to-optical conversion efficiency is 38.3% and the slope efficiency is 45.3%. To the best of our knowledge, this is the highest level of efficiency achieved for the domestic Nd：YAG ceramic rod laser.     

Diode-pumped Nd:YAG laser using reflective pump optics

We have examined the performance of a diode-laser side-pumped Nd:YAG laser using elliptical mirrors to focus the output of 6 × 10 W laser-diode arrays into the Nd: YAG rod. The multimode cw output power was 14 W with an optical to optical efficiency of 29%. With a resonator designed for TEM₀₀ mode operation 12 W of output was achieved.     

High power continuous-wave diode-laser-pumped Nd:YAG laser

We report on a diode-laser-pumped cw Nd: YAG laser operating at a power level of 150 W. By using a transverse pump geometry, the radiation of 54 diode lasers with an output power of 10 W each is coupled into a Nd:YAG rod. In multimode operation, an optical slope efficiency of 32% and an optical to optical efficiency of 29% are obtained. In TEM₀₀ operation, an output power of more than 30 W is realized with an optical to optical efficiency of 10%.     

1064 nm Nd:YAG laser intracavity pumped at 946 nm

We present for the first time a Nd:YAG laser emitting at 1064 nm intracavity pumped by a 946 nm diode-pumped Nd:YAG laser. A 885 nm laser diode is used to pump the first Nd:YAG crystal emitting at 946 nm, and the second Nd:YAG laser emitting at 1064 nm intracavity pumped at 946 nm. We achieved an output power of 7.97 W at 1064 nm for an absorbed pump power at 946 nm of 9.55 W, corresponding to an optical efficiency of 83.4%. The beam quality M² quality factor is about 1.1 at the maximum output power.     

Picosecond laser amplification system with 93 W high average power

A high average power picosecond laser amplification system with diode-end-pumped Nd:YVO₄ and diode-side-pumped Nd:YAG is described. Laser with power up to 92.7 W, repetition frequency of 73.3 MHz, pulse duration of 26.5 ps, and beam quality of M² < 3.5 is generated in the amplification system. Thermal-birefringence-induced depolarization in the Nd:YAG rod laser head amplifier is measured to be 21.9 W though birefringence compensation is performed.     

Optimization of Diode-Pumped Continuous-Wave Tape-Casting YAG/Nd:YAG/YAG-Ceramic Lasers

We demonstrate a diode-laser-pumped solid-state 1.06 μm laser using a novel YAG/Nd:YAG/YAG composite ceramics with a sandwich structure. We optimize the laser performance using different output couplers, pumping beam waists, and cavity lengths. A maximum CW output power of 11 W for the YAG/Nd:YAG/YAG-ceramic laser is obtained at an absorbed pump power of 25 W resulting in a slope efficiency of 49.4%. The excellent output performance shows that the novel YAG/Nd:YAG/YAGceramic material has a great potential in applications with diode-laser pumping.     

基于LD双端面泵浦的Nd:YAG高效率倍频激光器

报道了一种利用激光二极管（LD）双端面泵浦的Nd：YAG激光晶体,Cr⁴⁺：YAG晶体被动调Q,LBO临界相位匹配腔内倍频的高转换效率的绿光激光器。分析了双端面泵浦YAG激光器的热效应,实验中LD双端面泵浦,采用U型平行平面腔结构对Nd：YAG进行传导冷却。当总泵浦光为33.8 W时,得到被动调Q频率10 KHz、功率8.21 W的线偏振基频光输出。6.72 W的绿光输出的倍频效率为86%,输出光束为基模,M²为1.4。实验表明双端面泵浦YAG倍频激光器具有很高的转换效率。     

高功率高光束质量脉冲Nd: YAG激光器

 以实现高功率、高光束质量的脉冲激光输出为目的,对非对称平-凹谐振腔的结构进行了理论分析。设计出了高功率、高光束质量非对称放置的平-凹谐振腔、双氙灯泵浦的脉冲Nd: YAG激光器。当占空比为9%时,实现输出激光平均功率近480 W,光束参数积优于12.7 mm·mrad,电光转化效率近4%,与理论分析吻合,可用芯径300 μm的光纤传输,不稳定性优于±1%。加工实验证明有较好的质量：切割材料为不锈钢,厚度为3 mm时、切割速度为0.6 m/min和厚度为1.5 mm、切割速度为1.2 m/min时,两种情况下所得切缝宽度均为250 μm,且切割上下沿光滑。     

高功率准连续波腔内和频全固态黄光激光器

报道了高功率准连续波腔内和频全固态黄光激光器的研究结果.为获得高功率的黄光输出,首先,激光器采用准连续方式运转,在保持抽运水平的条件下降低热效应,从而提高光束质量和光光转换效率;第二,采用热近非稳腔腔型设计,双棒串接补偿热致双折射技术,获得大基模体积高光束质量的基频光;第三,通过优化腔型,采用L型共折叠臂平-凹对称腔,使两束基频光达到空间重合且满足功率配比.通过这些方法,得到了输出功率7.6W,重复频率1.1kHz的准连续波黄光输出.据我们所知,这是目前腔内和频方案所获得的最高功率全固态黄光输出. 关键词： 黄光激光 腔内和频 Nd：YAG激光 全固态激光器     

Two-pass amplification of CW laser by Nd/Cr:YAG ceramic Active mirror under lamp light pumping

The concept of an Active mirror with transparent Nd/Cr:YAG ceramics is proposed. A new ceramic material pumped by an arc-metal-halide lamp has been experimentally implemented. CW-laser light generated in a 1064 nm Nd:YAG micro-tip oscillator was amplified by an Active mirror made of Nd/Cr:YAG ceramic and pumped by CW arc-lamp light. The saturation power density of the Nd/Cr:YAG ceramic was lower than that of Nd:YAG because the stimulated-cross-section and lifetime were effectively enhanced by the sensitization of Cr ions. The maximum output laser power while keeping spatial beam quality was up to 3 W with an input lamp power of 9 W; the resulting optical-optical conversion efficiency of 33% was close to the theoretical prediction of nearly 50%.