基于光学反馈频率锁定的窄线宽稳定中红外激光产生技术研究

中红外精密激光光谱技术在痕量气体检测、基本物理常数测定等领域都有重要应用,然而由于缺乏窄线宽、稳定的中红外光源,很难实现中红外精密光谱测量.本文介绍了一种基于光学反馈频率锁定的窄线宽稳定中红外激光产生技术,分析了光学反馈实现激光到F-P腔锁定的可行性,利用一个高精细度中红外超稳F-P腔作为频率参考,基于光学反馈技术实现了量子级联激光器到该超稳腔的锁定.经过评估得到激光器线宽被压窄到1.1 Hz,压窄激光线宽的同时稳定了激光频率,将激光器的长期漂移控制在20 kHz/12 h.其中,为了获取长时间稳定的光学反馈,基于PDH技术获取了误差信号,用于对反馈相位的实时伺服控制.     

F-P腔不同扫频段透射谱锁频精度实验

针对窄线宽激光器输出谱线窄,难以被锁定的情况,利用F-P腔特有极窄线宽、高精细度特性对激光器谱线线宽实施压窄及频率锁定。通过设计实验方案并搭建锁频测试平台,利用F-P腔外部光反馈将窄线宽半导体激光器线宽压窄来提高锁频精度。通过监测正弦波调制下F-P腔对于4种不同直流电压下激光PZT扫频段的透射谱线,并对其分别进行解调和锁频精度测试,得到直流高压放大器电压为73 V时对窄线宽激光器进行扫频,激光器反馈锁频精度最高可达1.5 MHz。     

基于V型腔光反馈法的半导体激光器线宽压窄和频率锁定初步研究

线宽压窄和频率锁定是提高激光器(特别是半导体激光器)性能的重要手段。在理论分析光反馈时的半导体激光器线宽压窄和频率锁定机理的基础上,建立了一套基于高品质V型光学谐振腔的半导体激光器线宽压窄实验系统,并利用该系统开展了初步实验研究。通过对比无有光反馈情况下的V型腔的透射光扫描线形,初步验证了V型腔用于半导体激光器线宽压窄和频率锁定的可行性,为后续研究奠定了基础。     

基于V型腔光反馈法的半导体激光器线宽压窄和频率锁定初步研究

线宽压窄和频率锁定是提高激光器（特别是半导体激光器）性能的重要手段。在理论分析光反馈时的半导体激光器线宽压窄和频率锁定机理的基础上,建立了一套基于高品质V型光学谐振腔的半导体激光器线宽压窄实验系统,并利用该系统开展了初步实验研究。通过对比无有光反馈情况下的V型腔的透射光扫描线形,初步验证了V型腔用于半导体激光器线宽压窄和频率锁定的可行性,为后续研究奠定了基础。     

基于自制超稳定F-P腔压窄632.8nm外腔半导体激光线宽的实验研究

窄线宽激光由于其具有单色性好、稳定度高、相干长度长等优点,广泛应用于光电检测领域,包括相干通信、精密测量、光学频率标准、吸收光谱计量以及光与物质相互作用研究等。目前频率稳定的氦氖激光器线宽可以达到MHz量级,分布反馈式（DFB）光纤激光器线宽可达kHz量级,DFB半导体激光器线宽可以达到MHz量级,然而光栅反馈半导体激光器可以实现百kHz量级线宽的输出。为了进一步压窄各类激光器线宽,需要通过反馈控制技术来锁定激光到某一频率参考。该研究将自行设计的超稳腔作为频率参考,实现了632.8 nm外腔半导体激光器（ECDL）线宽的有效压窄。本窄线宽激光产生系统的研制包括超稳腔设计、光路设计、ECDL频率控制以及系统集成。超稳腔采用两镜法布里-珀罗腔（F-P腔）结构,腔体是膨胀系数约为10-6 K-1的微晶玻璃,腔镜为一对反射率达99.988 5%(±0.003 5%）的平面镜和凹面镜。为进一步减小外界环境对F-P腔腔长的影响,需要对腔体进行温度控制,本系统采用四片总功率为96 W的半导体制冷片以及水冷散热设计。同时为了降低声音和空气流动对腔模频率的影响,将F-P腔置于真空度为10-5 torr的真空室中;另外为了有效隔振,腔体与真空室用硅橡胶材料隔离。该系统采用的ECDL为德国Toptica公司的DL pro系列激光器,其具有压电陶瓷（PZT）和电流调制两个频率控制端,响应带宽分别为1 kHz和100 MHz。激光器的频率控制采用了Pound-Drever-Hall （PDH）锁频技术,18 MHz的调制频率加载到激光器的电流调制端,通过对F-P腔的反射信号进行解调获得误差信号,通过两路反馈控制,实现了近1 MHz的锁定带宽。通过对系统的不断优化,最后将自由运转状态下约300 kHz的激光线宽压窄到了10 kHz量级,并且系统运行稳定,连续12小时锁定的频率漂移量约为30 MHz。该研究研制的632.8 nm窄线宽激光源不仅可以应用到吸收光谱计量领域,同时也可以在光学面型精密测量领域发挥重要作用。     

利用自相位延迟方法测量单块腔反馈半导体外腔激光器的线宽

提出了采用单块折叠法布里-珀罗(F-P)腔作为外腔反馈元件实现窄线宽半导体激光器,采用单块腔的光学反馈来锁定外腔激光器,使用自相位延迟法测量该窄线宽激光器的线宽。实验结果表明,激光器线宽小于35kHz。实验还观测到由于单块腔耦合面上各耦合点的几何量和物理量误差不一样,随着折叠面兼输入输出耦合面上的耦合点的变化,外腔激光器的线宽发生改变。     

强反馈光纤光栅外腔半导体激光器

在理论上对强外腔反馈情形的半导体激光器线宽压窄效应进行了分析，对消反膜剩余反射率，外腔反射率，外腔腔长对线宽压缩的影响进行了研究，在实验上采用光纤光栅作为反馈元件，与一端镀有消反膜的１．５μｍ波段的常规多纵模交导体激光器耦合，构成强反馈光纤光栅外腔半导体激光器，得到单频窄线宽的激光输出，静态下边模抑制比大于３０ｄＢ，线宽小于１２０ｋＨｚ。     

掺Er光纤飞秒激光器中电光晶体对激光器参数的影响

由于受增益介质上能级寿命的影响,掺Er光纤光梳的梳齿线宽一般在百kHz量级.为了实现光梳梳齿线宽的压窄,一种有效的方法是在激光器中增加快速响应的电光晶体,使光纤光梳的伺服锁定带宽提高到百kHz以上,为光纤光梳的快速伺服锁定提供反馈机构.这其中,高品质的飞秒激光器是核心.基于此,本文主要研究了掺Er光纤飞秒激光器中电光晶体对激光器参数的影响.通过计算电光晶体的折射率、色散、相位延迟等参数,分析了电光晶体对激光器参数的影响,并在实验上获得了电光晶体电压对激光器重复频率和载波包络偏移频率的影响,进而通过电光晶体实现了对光纤光梳重复频率和载波包络偏移频率的锁定.通过锁定光纤飞秒激光器与窄线宽激光器的拍频信号,验证了电光晶体的引入使激光器的伺服锁定带宽提高到了236 kHz,为窄线宽飞秒光学频率梳的建立提供了技术基础.     

基于光电负反馈的光注入1550nm垂直腔面发射激光器产生窄线宽微波信号

基于1 550nm垂直腔面发射激光器在平行偏振光注入下呈现的单周期非线性动力学状态,进一步引入光电负反馈,得到了高质量的微波信号.实验研究结果表明:平行偏振光注入下,通过调节注入光的注入强度及频率,1 550nm垂直腔面发射激光器可呈现注入锁定、单周期、倍周期、混沌等多种非线性动力学状态;在合适的注入参量下,平行偏振光注入1 550nm垂直腔面发射激光器可产生光谱具有单边带结构、频率超过10GHz的光子微波信号,但该微波信号的线宽较宽(达MHz量级);进一步引入光电负反馈后,通过选取合适的光电反馈强度,可将该微波信号的线宽减小至一百多kHz(减小两个量级以上);在选择优化的反馈强度条件下,仅通过简单调节注入光强度,可实现窄线宽光子微波信号的频率在一定范围内连续可调谐.     

不同波长的激光器通过法布里-珀罗腔相对于铯原子谱线的锁定

采用共焦法布里珀罗腔(CFP)作为桥梁,可以实现不在原子、分子跃迁线附近的单频激光器相对于原子、分子跃迁线的锁定,从而可以有效地抑制激光频率的漂移。在实验中通过射频频率调制光谱技术结合饱和吸收光谱(SAS)将自制852nm光栅外腔反馈半导体激光器锁定到铯6S1/2Fg=4-6P3/2Fe=4、5交叉线上,通过Pound-Drever-Hall(PDH)射频边带技术将作为桥梁的共焦法布里珀罗腔锁定在852nm激光频率上。再通过PDH方法将830nm和908nm两台远离铯原子D2线的外腔半导体激光器同时锁定在作为桥梁的共焦法布里珀罗腔上,实现了830nm和908nm两台激光器相对于铯原子跃迁线的锁定。由锁定后的误差信号估算,20s内852nm激光器相对于铯原子Fg=4-Fe=4、5交叉线的频率起伏小于±540kHz,830nm、908nm激光器相对于共焦法布里珀罗腔的频率起伏分别小于±340kHz和±60kHz,共焦法布里珀罗腔相对于852nm激光的频率起伏小于±550kHz。     

基于光注入半导体激光器单周期振荡的光子微波产生及全光线宽窄化

本文对基于光注入半导体激光器的单周期动力学态产生光子微波并利用光反馈压缩其线宽进行了实验研究. 研究结果表明: 通过适当调节注入参数, 能对该方法产生的光子微波频率在数十GHz范围内进行连续、大范围地调节; 通过引入光反馈并精细调节反馈强度, 光子微波的线宽能够从40—100 MHz的范围被压缩约两个数量级至300—900 kHz范围;反馈长度对光子微波的线宽几乎没有影响, 但当反馈长度精细变化时, 光子微波频率会出现一定范围内的周期性漂移.     

Numerical investigation on photonic microwave generation by a sole excited-state emitting quantum dot laser with optical injection and optical feedback

Based on three-level exciton model, the enhanced photonic microwave signal generation by using a sole excited-state(ES) emitting quantum dot(QD) laser under both optical injection and optical feedback is numerically studied. Within the range of period-one(P1) dynamics caused by the optical injection, the variations of microwave frequency and microwave intensity with the parameters of frequency detuning and injection strength are demonstrated. It is found that the microwave frequency can be continuously tuned by adjusting the injection parameters, and the microwave intensity can be enhanced by changing the injection strength. Moreover, considering that the generated microwave has a wide linewidth, an optical feedback loop is further employed to compress the linewidth, and the effect of feedback parameters on the linewidth is investigated. It is found that with the increase of feedback strength or delay time, the linewidth is evidently decreased due to the locking effect. However, for the relatively large feedback strength or delay time, the linewidth compression effect becomes worse due to the gradually destroyed P1 dynamics. Besides, through optimizing the feedback parameters, the linewidth can be reduced by up to more than one order of magnitude for different microwave frequencies.     

用于高分辨率光谱研究的窄线宽半导体激光器及其特性研究

报道了一种新型结构的弱反馈外腔半导体激光器，利用此结构将煌激光线宽压窄至５００ｋＨｚ以下。这种激光器可用于高分辨率激光光谱，磁光阱囚禁和原子和原子喷泉量子频标等方面。另外还从理论上研究了其线宽，电调率等物理参量间的关系，得出了有用的关系式，并通过实验对此作了验证。     

Influence of laser linewidth on external-cavity frequency doubling efficiency of a 1.56μm master oscillator fiber power amplifier

By using an external-cavity frequency-doubling master oscillator fiber power amplifier (MOPA), a 700~mW continuous-wave single-frequency laser source at 780~nm is produced. It is shown that the frequency doubling efficiency is improved when the seed diode laser is optically locked to a resonant frequency of a confocal Fabry--Perot (F-P) cavity. This phenomenon can be attributed to the narrowing of the 1.56~μ m laser linewidth and explained by our presented theoretical model. The experimental results are found to be in good agreement with the theoretical predictions.     

Frequency stabilised grating feedback laser diode for atom cooling applications

The free running linewidth of an external cavity grating feedback diode laser is on the order of a few megahertz and is limited by the mechanical and acoustic vibrations of the external cavity. Such frequency fluctuations can be removed by electronic feedback. We present a hybrid stabilisation technique that uses both a Fabry–Perot confocal cavity and an atomic resonance to achieve excellent short and long term frequency stability. The system has been shown to reduce the laser linewidth of an external cavity diode laser by an order of magnitude to 140 kHz, while limiting frequency excursions to 60 kHz relative to an absolute reference over periods of several hours. The scheme also presents a simple way to frequency offset two lasers many gigahertz apart which should find a use in atom cooling experiments, where hyperfine ground-state frequency separations are often required.     

Long-external-cavity distributed Bragg reflector laser with subkilohertz intrinsic linewidth

We report on a simple, compact, and robust 780 nm distributed Bragg reflector laser with subkilohertz intrinsic linewidth. An external cavity with optical path length of 3.6 m, implemented with an optical fiber, reduces the laser frequency noise by several orders of magnitude. At frequencies above 100 kHz the frequency noise spectral density is reduced by over 33 dB, resulting in an intrinsic Lorentzian linewidth of 300 Hz. The remaining low-frequency noise is easily removed by stabilization to an external reference cavity. We further characterize the influence of feedback power and current variation on the intrinsic linewidth. The system is suitable for experiments requiring a tunable laser with narrow linewidth and low high-frequency noise, such as coherent optical communication, optical clocks, and cavity QED experiments.