Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Microstructure and microwave dielectric properties of lead borosilicate glass ceramics with Al2O3

The effects of Al₂O₃ addition on both the sintering behavior and microwave dielectric properties of PbO-B₂O₃-SiO₂ glass ceramics were investigated by Fourier transform infrared spectroscope (FTIR), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that with the increase of Al₂O₃ content the bands assigned to [SiO₄] nearly disappear. Aluminum replaces silicon in the glass network, which is helpful for the formation of boron-oxygen rings. The increase of the transition temperature T _g and softening temperature T _f of PbO-B₂O₃-SiO₂ glass ceramics leads to the increase of liquid phase precipitation temperature and promotes the structure stability in the glasses, and consequently contributes to the decreasing trend of crystallization. Densification and dielectric constants increase with the increase of Al₂O₃ content, but the dielectric loss is worsened. By contrast, the 3% (mass fraction) Al₂O₃-doped glass ceramics sintered at 725 °C have better properties of density ρ=2.72 g/cm³, dielectric constant ɛ _r =6.78, dielectric loss tan δ=2.6×10⁻³ (measured at 9.8 GHz), which suggest that the glass ceramics can be applied in multilayer microwave devices requiring low sintering temperatures.     

Low-temperature sintering and microwave dielectric properties of Li2MgTi3O8 ceramics doped with BaCu（B2O5）

The influences of BaCu(B₂O₅) (BCB) addition on sintering, microstructure and microwave dielectric properties of Li₂MgTi₃O₈ ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu(B₂O₅) addition can effectively reduce the sintering temperature to 900 °C, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of ɛ _r=24.5, Q×f =24 622 GHz, τ _f=4.2×10⁻⁶ °C⁻¹ are obtained for 1.0% BCB-doped Li₂MgTi₃O₈ ceramics sintered at 900 °C for 3 h. The BCB-doped Li₂MgTi₃O₈ ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.     

Effects of heat treatment temperature on crystallization and thermal expansion coefficient of Li2O-Al2O3-SiO2

The basic glass of Li₂O-Al₂O₃-SiO₂ system using P₂O₅ as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. The crystalline phases and the microstructure of the glass-ceramics were investigated by using X-ray diffraction and scanning electron microscopy. The results show that the glass based on Li₂O-Al₂O₃-SiO₂ oxides using P₂O₅ as nucleator can be prepared at lower melt temperature of 1450°C and the glass-ceramics with lower thermal expansion coefficient of 21.6 × 10⁻⁷°C⁻¹ can also be obtained at 750°C. The glass-ceramics contain a few crystal phases in which the main crystal phase is β-quartz solid solution and the second crystal phase is β-spodumene solid solution. When the heat treatment temperature is not higher than 650°C, the transparent glass-ceramics containing β-quartz solid solution can be prepared. β-quartz solid solution changes into β-spodumene solid solution at about 750°C. And the appearance of the glass-ceramics changes from translucent, part opaque to complete opaque with increasing temperature.     

Microstructure and microwave dielectric properties of CaO-B2O3-SiO2 glass ceramics with various B2O3 contents

The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 (CBS) glass ceramics were investigated by Fourier transform infrared spectroscopy (FTIR),X-ray diffractometry (XRD) and scanning electron microscopy (SEM).The results show that the increasing amount of B2O3 causes the increase of the contents of [BO3],[BO4] and [SiO4],which deduces the increase of CaB2O4 and α-SiO2 and the decrease of CaSiO3 correspondingly.No new phase is observed throughout the...     

Effect of nucleating agents and heat treatments on the crystallization of magnesium aluminosilicate transparent glass-ceramics

The crystallization behavior and transparent property of MgO-Al2O3-SiO2 (MAS) glasses with TiO2 and TiO2+ZrO2 as nucleating agents were discussed by differential thermal analysis, X-ray diffraction, field emission-environment scanning electron microscope, energy dispersive spectrum and UV-VIS-NIR scanning spectrophotometer. It was found that the glass crystallized at 950 ℃ with ZrO2 less than 3% could obtain transparent glass ceramic, which presented purple to colorless. With the nucleating agent additives (5% TiO2+3% ZrO2), the colorless transparent glass-ceramics with spinel as the main crystal phase could be prepared, and the transmittance reached about 80% . As the crystallized temperature increase to 1 000 ℃, besides spinel(MgAl2O4), sapphirine (Mg3.5Al9Si1.5O20) and ZrTiO4 precipitated from matrix glass, and the transmitance of glass-ceramic decreased.     

Preparation of BN／SiO2 ceramics by PIP method

The precursor infiltration and pyrolysis(PIP) method for preparation of BN/SiO2 composites was used to improve mechanical properties, dielectric properties and feasibility of high temperature dielectric parts with large dimensions and complex shapes. In the processing procedure, the porous BN ceramic matrix was first successfully prepared by compacting the mixed powders of B and BN and then sintering them at a certain temperature under normal pressure of N2. The polycarbosilane(PCS) solution was vacuum infiltrated into porous BN ceramics at the room temperature and then at 800℃ in the air to depolimerize out amorphous SiO2, and sintered further at 1 300℃ in N2 to get BN/SiO2 composites. The microstructure of materials was studied by means of X-ray diffraction and electron probe micro analysis. The thermo-decomposition mechanism of PCS was investigated by a TG-DTA and infrared (IR) spectrum analysis. The flexural strengths were measured by the three-point bending method. The dielectric constant and the loss tangent were measured by the wave-guide method. The results show BN/SiO2 composites were fabricated. The obtained composites posses a flexural strength of 61.96 - 93.31 MPa, the dielectric constant in the range of 3.50 - 3.78 and the order of magnitude of the loss tangent at 10^-3 , which are good for the high tempera turedielectric parts with large size and complex shapes.     

The Effect of Bi2O3 on the Structure and Microwave Dielectric Properties of Ba6-3xNd8＋2xTi18O54 System（x=2/3）

The structures and dielectric properties of Ba6-3xNd8＋2xTi18O54 system（x=2/3） doped with different contents of Bi2O3, whose final molecular formula is Ba6-3x（Nd1-yBiy）8＋2xTi18O54 were investigated. It is indicated that the dielectric constant increases greatly whereas Q value（f0=4 GHz） decreases with the increase of Bi2O3 content. However, the temperature coefficient could be controlled below 0±30×10^-6/℃ in the experiment. These phenomena are related to the appearance of a new phase, Bi4Ti3O12, which has high dielectric constant. Also, that Bi^3＋（0.13 nm） substitutes for Nd^3＋（0.099 5 nm） will increase the unit cell volume, which will lead to the enlargement of the octahedron B site occupied by Ti^4＋. So the spontaneous polarization of Ti^4＋ ions will be strengthened. Besides, Bi^3＋ will fill up some vacancies which Ba^2＋ or Nd^3＋ ions leave in two A1 sites and four A2 sites. More positive ions polarize, which also contributes to higher dielectric constant. The samples got with the optimium properties are sintered at 1 200 ℃ for 4 h, when y=0.25, ε≈110, Q≈5 400（f0=4 GHz）, TCC=-4.7×10^-6/℃; When y=0.3, ε≈120, Q≈5 000（f0=4 GHz）, TCC=-24×10^-6/℃.     

The structure and properties of Ag(Nb0.8Ta0.2)O3 ceramic doped with MnNb2O6

The influences of doping of MnNb2O6 on the structure and dielectric properties of Ag(Nb0.8Ta0.2)O3 were illustrated. Ag(Nb0.8Ta0.2)O3 samples doped with different amount of preformed MnNb2O6 (1 mol%, 2 mol%, 3 mol%, 4 mol%, 6 mol%, 8 mol%) were prepared by traditional solid-state reaction method and characterized by XRD, SEM and EDS, and the dielectric properties of samples were compared. The experiment results indicated that when the doping amount of MnNb2O6 was greater than 3 mol%, second phase appeared because of the solid solution limit. The permittivity of the Ag(Nb0.8Ta0.2)O3 samples doped with MnNb2O6 firstly increased and then decreased with the sintering temperature, while the dielectric loss decreased first, and then increased slightly. 1 100 ℃ seems to be the most proper sintering temperature for most of the samples. When the amount of MnNb2O6 is about 3 mol%, the samples have the best dielectric properties, larger permittivity and smaller dielectric loss.     

Structure and mechanical properties of ZrO2-mullite nano-ceramics in SiO2-Al2O3-ZrO2 system

ZrO2-mullite nano-ceramics were fabricated by in-situ controlled crystallizing from SiO2-Al2O3-ZrO2 amorphous bulk. The thermal transformation sequences of the SiO2-Al2O3-ZrO2 amorphous bulk were investigated by X-ray diffraction, infrared spectrum, scanning electron microscope and differential scanning calorimetric. And the mechanical properties of the nano-ceramics were studied. The results show that the bulks are still in amorphous state at 900 ℃ and the t-ZrO2 forms at about 950 ℃ with a faint spinel-like phase which changes into mullite on further heating. ZrO2 and mullite become major phases at 1 100 ℃ and an amount of m-ZrO2 occur at the same time. The sample heated at 950 ℃ for 2 h and then at 1 100 ℃ for 1 h shows very dense and homogenous microstructure with ball-like grains in size of 20-50 nm. With the increase of crystallization temperature up to 1 350 ℃, the grains grow quickly and some grow into lath-shaped grains with major diameter of 5 μm. After two-step treatment the highest micro-hardness, flexural strength and fracture toughness of the samples are 13.72 GPa, 520 MPa and 5.13 MPa·m1/2, respectively.     

Investigation on plasma-sprayed ZrO2 thermal barrier coating on nickel alloy substrate

The thermal barrier coatings with NiCrAlY alloy bonding layer, NiCrAlY-Y₂O₃ stabilized ZrO₂ transition layer and Y₂O₃ stabilized ZrO₂ ceramic layer are prepared on nickel alloy substrates using the plasma spray technique. The relationship among the composition, structure and property of the coatings are investigated by means of optical microscope, scanning electronic microscope and the experiments of thermal shock resistance cycling and high temperature oxidation resistance. The results show that the structure design of introducing a transition layer between Ni alloy substrate and ZrO₂ ceramic coating guarantees the high quality and properties of the coatings; ZrO₂ coatings doped with a little SiO₂ possesses better thermal shock resistance and more excellent hot corrosion resistance as compared with ZrO₂ coating materials without SiO₂; the improvement in performance of ZrO₂ coating doped with SiO₂ is due to forming more dense coating structure by self- closing effects of the flaws and pores in the ZrO₂ coatings. Biography of the first author: LU An-xian, Ph.D, professor, born in Jan. 1960, majoring in inorganic non-metal materials.     

Preparation and optical properties of Er<Superscript>3+</Superscript>: Na<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> transparent glass-ceramics

Na₂O-Al₂O₃-SiO₂ glass-ceramics doped with Er³⁺ ions were synthesized by the conventional melt quenching technique at a low melting temperature. The samples were characterized by differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis-NIR scanning spectrophotometry, and fluorescence spectrometry. The results show that the main crystalline phase of glass-ceramics is nepheline.The best heat-treatment process is at 520 °C for 2 h. Because the up-conversion luminescence and near infrared luminescence properties of glass doped with Eu³⁺ are studied in detail.     

Influence of soaking time on nonlinear electrical behavior and dielectric properties of TiO2-based varistor ceramics

The influence of soaking time on the nonlinear electrical behavior and dielectric properties of TiO₂-based varistor ceramics was investigated. Based on single sintering process, six disk samples of (Sr, Bi, Si, Ta)-doped TiO₂-based varistor ceramics were fabricated by sintering at 1 250 °C for 0.5–5.0 h. The samples were characterized by X-ray diffraction, voltage-current characteristics, energy spectra, metallographs, breakdown voltages, and apparent dielectric constant. It is found that the breakdown electrical field intensity at a current density of 10 mA/cm² decreases from 5.5 to 4.1 V/mm first and then increases to 7.0 V/mm, the nonlinear coefficient increases from 2.39 to 2.62 first and then decreases to 2.42, and the apparent dielectric constant increases from 98 200 to 115 049 first and then decreases to 73 865 with the soaking time increasing from 0.5 to 5.0 h. These indicate that the optimal soaking time is 2.0–3.0 h considering both nonlinear electrical behavior and dielectric properties.     

Densification and sintering dynamics of 10NiO-NiFe2O4 composites doped with CaO

The effects of CaO content in the range from 0 to 4.0%, and sintering temperature on the phase composition, relative density and electrical conductivity of 10NiO-NiFe2O4 composites doped with CaO were studied. The results show that there is no change of structure for NiO or NiFe2O4; there is apparent oxygen absorbing and releasing behavior during the heating process in air for 10NiO-NiFe2O4 composites. Introduction of CaO can accelerate the densification of 10NiO-NiFe2O4 composites. The maximum value of relative density is 98.75% for composite doped with 2.0% CaO and sintered at 1 200 ℃, which is beyond about 20% for the undoped composites. The sintering activated energy of sample containing 2% CaO decreases by 15.87 kJ/mol, compared with that of the undoped sample.     

Properties of plasma sprayed NiCrAlY+(ZrO2+Y2O3) coating on refractory steel surface

NiCrAlY+(ZrO₂+Y₂O₃) thermal barrier coating was prepared on the surface of refractory steel 1Cr18Ni9Ti with plasma spraying technique. The phases and microstructure of the thermal barrier coating were determined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that the bonding between thermal barrier coating and substrate is sound. The surface hardness of 1Cr18Ni9Ti reaches up to 1 000 HV, but that of substrate is only 300 HV. The patterns sprayed with CoNiCrAlY+(ZrO₂+Y₂O₃) ceramic coating have a good heat insulation effect at 800 °C for heat insulation temperature difference reaches 54 °C, which increases the operating temperature and service life of refractory steel. Foundation item: Project (5040202140) supported by Scientific Research Common Program of Beijing Municipal Commission of Education     

Preparation and properties of crystallizable Glass/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites for LTCC material

The investigated low temperature Co fired ceramics(LTCC) composite of 60wt% CaO-Al2O3-B2O3-SiO2 glass and 40wt% α-Al2O3 as a filler is a non-reactive system, which is a critical part of the low temperature Co fired ceramics process. Through a study on densification process, the phase transformation and microstructure can be revealed. Its composites typically consist of CaO-Al2O3-B2O3-SiO2 glass and α-Al2O3 powders of average particle size (D50=3.49 mm). The sintering behavior, phase evaluation, sintered morphology, and microwave dielectric properties were investigated. In the fire range of 800 to 900 ℃, the composites were crystallized after completion of densification. It is found that the composites start to densify at 825 ℃, simultaneously, the dielectric constant (εr) reaches its maximum. With increasing heat-treatment temperatures, due to the loose microstructure of the material, tanδ increases slightly. The last of the sintered samples were identified as partly Anorthite at 850 ℃. At that temperature it has εr of 7.9 and tanδ less than 1×10-3, and can be used as a promising LTCC material.     

硼掺杂对Ba_2TiSi_2O_8玻璃陶瓷结构与介电性能的影响

采用溶胶凝胶法合成了掺杂硼的Ba2TiSi2O8(BTS-B)粉体,并将粉体压成样品在同一马弗炉分别在900、950、1 000、1 050、1 100和1 150℃下烧结成瓷。并且对陶瓷的真密度和径向收缩率进行测试以确定最佳烧结温度。实验结果表明,掺硼的BTS陶瓷的最佳烧结温度为1 050℃;硼的引入并没有影响BTS陶瓷的主晶相;硼的存在降低陶瓷的烧结温度;陶瓷的介电常数和介质损耗随着硼含量的增加呈现先增大后减小的趋势,BTS-B1.5的介电常数最大(18左右)。     

Effects of oxidation treatment on properties of SiO2f/SiO2-BN composites

The silica fiber reinforced silica and boron nitride-based composites (SiO_2f/SiO₂-BN) were prepared firstly via the sol-gel method and then the urea route, and the effects of oxidation treatment on the component, structure, mechanical and dielectric properties of the composites were investigated. The results show that the oxidation treatment at 450 °C will not impair the structure of boron nitride, and carbon is the main impurity with the excessive urea. The density of SiO_2f/SiO₂-BN composites is 1.81 g/cm³, and the flexural strength and elastic modulus are 113.9 MPa and 36.5 GPa, respectively. After oxidation treatment, the density varies to 1.80 g/cm³, and the flexural strength and elastic modulus are decreased to 58.9 MPa and 9.4 GPa, respectively. The mechanical properties of the composites are severely damaged, but they still exhibit a good toughness. The composites show excellent dielectric properties with the dielectric constant and loss tangent being 3.22 and 0.003 9, respectively, which indicates that the oxidation treatment is ineffective to improve the dielectric properties of SiO_2f/SiO₂-BN composites.     

Preparation and properties of 4.25Cu-0.75Ni／NiFe2O4 cermet

4.25Cu-0.75Ni/NiFe₂O₄ cermets were prepared by doping NiFe₂O₄ ceramic matrix with the mixed powders of Cu and Ni or Cu-Ni alloy powder as the electrical conducting metallic elements. The effects of technological parameters, such as the adding modes of metallic elements, the ball milling time, the sintering time and the sintering temperature, on the relative density and resistivity of the cermets were studied. The results show that the resistivity of 4.25Cu-0.75Ni/NiFe₂O₄ cermets decreases with increasing temperature, and has a turning point at 590 °C, which is similar to that of NiFe₂O₄ ceramic. The sintering temperature and adding modes of metallic elements have a great influence on the properties of 4.25Cu-0.75Ni/NiFe₂O₄ cermets. When the sintering temperature increases from 1200 °C to 1300 °C, the relative density increases from 89.86% to 95.33%, and the resistivity at 960 °C decreases from 0.11 Ω · cm to 0.03 Ω · cm, respectively. When the metallic elements are added with the mixed powders of Cu and Ni, the cermets of finely and uniformly dispersed metallic phase, high density and electric conductivity are obtained. The relative density and resistivity at 960 °C are 90.23% and 0.04 Ω · cm respectively for the cermet samples sintered at 1200 °C for 2 h, which are both better than those of the cermets prepared under the same technique conditions but with the metallic elements added as 85Cu-15Ni alloy powders. Foundation item: Project (G1999064903) supported by the National Key Fundamental Research and Development Program of China; project(2001AA335013) supported by the National High Technology Research and Development Program of China; project (50204014) supported by the National Natural Science Foundation of China     

Sintering of the NiFe2O4-10NiO/xNi Cermet

The sintering behavior of NiFe2 O4-10NiO/xNi cermet which was used as the most prospective inert anode materials for aluminum electrolysis was studied by examining the effects of raw powder particle size, sintering temperature, and the contents of Ni. The results show that fine particle size enables the powder to have high driving force for sintering. High temperature is beneficial to densification, but the ultra-high temperature does harm to the improvement of the density. The samples of NiFe2O4-10NiO/SNi has the highest relative density of 97.28 % when it is sintered at 1 350 ℃, but it decreases to 95.23 % when sintered at 1 400 ℃. Low addition of Ni has a great help to the sintering of NiFe2 O4-10NiO matrix. When the samples are sintered at 1 350 ℃ and the mass fraction of Ni is 5%, the highest relative density is gained, but the density decreases with the further increase of Ni contents. The low density of the sintered samples of NiFe2 O4-10NiO/17Ni is attributed to the high volume fraction of pores.