AlGaN/GaN high-electron-mobility transistors with transparent gates by Al-doped ZnO

AlGaN/GaN high-electron-mobility transistors （HEMTs） with Al-doped ZnO （AZO） transparent gate electrodes are fabricated, and Ni/Au/Ni-gated HEMTs are produced in comparison. The AZO-gated HEMTs show good DC characteristics and Schottky rectifying characteristics, and the gate electrodes achieve excellent transparencies. Compared with Ni/Au/Ni-gated HEMTs, AZO-gated HEMTs show a low saturation current, high threshold voltage, high Schottky barrier height, and low gate reverse leakage current. Due to the higher gate resistivity, AZO-gated HEMTs exhibit a current-gain cutoff frequency （fT） of 10 GHz and a power gain cutoff frequency （fmax） of 5 GHz, and lower maximum oscillation frequency than Ni/Au/Ni-gated HEMTs. Moreover, the C-V characteristics are measured and the gate interface characteristics of the AZO-gated devices are investigated by a C-V dual sweep.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下，研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明，钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降；在高漏偏压下，场板的尺寸对器件抑制崩塌的能力有较大影响，而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现，场板结构不仅能够抑制虚栅的充电过程，而且提供了放电途径，有利于虚栅的放电，从而抑制电流崩塌.在此基础上，通过建立场板介质对虚栅放电的模型，解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因.     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下,研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明,钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降;在高漏偏压下,场板的尺寸对器件抑制崩塌的能力有较大影响,而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现,场板结构不仅能够抑制虚栅的充电过程,而且提供了放电途径,有利于虚栅的放电,从而抑制电流崩塌.在此基础上,通过建立场板介质对虚栅放电的模型,解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因. 关键词： AlGaN/GaN HEMT 场板 电流崩塌     

AlGaN/GaN HEMTs grown on silicon (001) substrates by molecular beam epitaxy

We report the realization of an AlGaN/GaN HEMT on silicon (001) substrate with noticeably better transport and electrical characteristics than previously reported. The heterostructure has been grown by molecular beam epitaxy. The 2D electron gas formed at the AlGaN/GaN interface exhibits a sheet carrier density of 8×10¹² cm⁻² and a Hall mobility of 1800 cm²/V s at room temperature. High electron mobility transistors with a gate length of 4 μm have been processed and DC characteristics have been achieved. A maximum drain current of more than 500 mA/mm and a transconductance g_m of 120 mS/mm have been obtained. These results are promising and open the way for making efficient AlGaN/GaN HEMT devices on Si(001).     

Influence of Schottky drain contacts on the strained AlGaN barrier layer of AlGaN/AlN/GaN heterostructure field-effect transistors

Rectangular Schottky drain AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) with different gate contact areas and conventional AlGaN/AlN/GaN HFETs as control were both fabricated with same size. It was found there is a significant difference between Schottky drain AlGaN/AlN/GaN HFETs and the control group both in drain series resistance and in two-dimensional electron gas (2DEG) electron mobility in the gate-drain channel. We attribute this to the different influence of Ohmic drain contacts and Schottky drain contacts on the strained AlGaN barrier layer. For conventional AlGaN/AlN/GaN HFETs, annealing drain Ohmic contacts gives rise to a strain variation in the AlGaN barrier layer between the gate contacts and the drain contacts, and results in strong polarization Coulomb field scattering in this region. In Schottky drain AlGaN/AlN/GaN HFETs, the strain in the AlGaN barrier layer is distributed more regularly.     

DLTS characterization of silicon nitride passivated AlGaN/GaN heterostructures

Passivating the ungated surface of AlGaN/GaN HEMTs with silicon nitride (SiN) is effective in improving the microwave output power performances of these devices. However, very little information is available about surface states in GaN-based HEMTs after SiN passivation. In this work we investigate AlGaN/GaN HEMTs structures having either metal–semiconductor or metal–SiN–semiconductor gate contacts. In short gate devices conductance DLTS measurements point out a hole-like peak that shows an anomalous behaviour and can be ascribed to surface states in the access regions of the device. In insulated gate HEMTs a band of levels is detected and ascribed to surface states, whose energy ranges from 0.14 to 0.43 eV. Capacitance–voltage measurements allow us to point out the existence of a second band of interface states deeper in energy than the former one. This band is responsible for slow transients observed in the characteristics of the insulated gate FAT-HEMT.     

Reverse blocking enhancement of drain field plate in Schottky-drain AlGaN/GaN high-electron mobility transistors

In this paper, we present the combination of drain field plate(FP) and Schottky drain to improve the reverse blocking capability, and investigate the reverse blocking enhancement of drain FP in Schottky-drain AlGaN/GaN high-electron mobility transistors(HEMTs). Drain FP and gate FP were employed in a two-dimensional simulation to improve the reverse blocking voltage(VRB) and the forward blocking voltage(VFB). The drain-FP length, the gate-FP length and the passivation layer thickness were optimized. VRBand VFBwere improved from-67 V and 134 V to-653 V and 868 V respectively after optimization. Simulation results suggest that the combination of drain FP and Schottky drain can enhance the reverse blocking capability significantly.     

增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

AlGaN表面坑状缺陷及GaN缓冲层位错缺陷对AlGaN/GaN HEMT电流崩塌效应的影响

利用金属有机气相外延(MOVPE)技术生长了具有不同AlGaN表面坑状缺陷和GaN缓冲层位错缺陷密度的AlGaN/GaN 高电子迁移率晶体管(HEMT)样品,并对比研究了两种缺陷对器件栅、漏延迟电流崩塌效应的影响.栅延迟测试表明,AlGaN表面坑状缺陷会引起栅延迟电流崩塌效应和源漏电阻的增加,而且表面坑状缺陷越多,栅延迟电流崩塌程度和源漏电阻的增加越明显.漏延迟测试显示,AlGaN表面坑状缺陷对漏延迟电流崩塌影响不大,而GaN缓冲层位错缺陷主要影响漏延迟电流崩塌.研究结果表明,AlGaN表面坑状缺陷和Ga 关键词： AlGaN/GaN HEMT 电流崩塌 坑状缺陷 位错缺陷     

Effects of SiNx on two-dimensional electron gas and current collapse of AlGaN/GaN high electron mobility transistors

SiN_x is commonly used as a passivation material for AlGaN/GaN high electron mobility transistors (HEMTs). In this paper, the effects of SiN_x passivation film on both two-dimensional electron gas characteristics and current collapse of AlGaN/GaN HEMTs are investigated. The SiN_x films are deposited by high- and low-frequency plasma-enhanced chemical vapour deposition, and they display different strains on the AlGaN/GaN heterostructure, which can explain the experiment results.     

High-electric-field-stress-induced degradation of SiN passivated AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) are fabricated by employing SiN passivation, this paper investigates the degradation due to the high-electric-field stress. After the stress, a recoverable degradation has been found, consisting of the decrease of saturation drain current I_Dsat, maximal transconductance g_m, and the positive shift of threshold voltage V_TH at high drain-source voltage V_DS. The high-electric-field stress degrades the electric characteristics of AlGaN/GaN HEMTs because the high field increases the electron trapping at the surface and in AlGaN barrier layer. The SiN passivation of AlGaN/GaN HEMTs decreases the surface trapping and 2DEG depletion a little during the high-electric-field stress. After the hot carrier stress with V_DS=20 V and V_GS=0 V applied to the device for 10⁴ sec, the SiN passivation decreases the stress-induced degradation of I_Dsat from 36% to 30%. Both on-state and pulse-state stresses produce comparative decrease of I_Dsat, which shows that although the passivation is effective in suppressing electron trapping in surface states, it does not protect the device from high-electric-field degradation in nature. So passivation in conjunction with other technological solutions like cap layer, prepassivation surface treatments, or field-plate gate to weaken high-electric-field degradation should be adopted.     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al₂O₃ AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al₂O₃薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现：所制备的Al₂O₃薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较 关键词： 2O₃')" href="#">Al₂O₃ ALD GaN MOSHEMT     

AlGaN/GaN 高电子迁移率晶体管漏电流退化机理研究

本文首先制备了与AlGaN/GaN高电子迁移率晶体管 (HEMT) 结构与特性等效的AlGaN/GaN异质结肖特基二极管, 采用步进应力测试比较了不同栅压下器件漏电流的变化情况, 然后基于电流-电压和电容-电压测试验证了退化前后漏电流的传输机理, 并使用失效分析技术光发射显微镜 (EMMI) 观测器件表面的光发射, 研究了漏电流的时间依赖退化机理. 实验结果表明: 在栅压高于某临界值后, 器件漏电流随时间开始增加, 同时伴有较大的噪声. 将极化电场引入电流与电场的依赖关系后, 器件退化前后的 log(I_FT/E)与√E 都遵循良好的线性关系, 表明漏电流均由电子Frenkel-Poole (FP) 发射主导. 退化后 log(I_FT/E)与√E 曲线斜率的减小, 以及利用EMMI在栅边缘直接观察到了与缺陷存在对应关系的“热点”, 证明了漏电流退化的机理是: 高电场在AlGaN层中诱发了新的缺陷, 而缺陷密度的增加导致了FP发射电流I_FT的增加. 关键词： AlGaN/GaN 高电子迁移率晶体管 漏电流 退化机理     

Enhancement-mode AlGaN/GaN high electronic mobility transistors with thin barrier

An enhancement-mode (E-mode) AlGaN/GaN high electron mobility transistor (HEMTs) was fabricated with 15-nm AlGaN barrier layer. E-mode operation was achieved by using fluorine plasma treatment and post-gate rapid thermal annealing. The thin barrier depletion-HEMTs with a threshold voltage typically around --1.7 V, which is higher than that of the 22-nm barrier depletion-mode HEMTs (--3.5 V). Therefore, the thin barrier is emerging as an excellent candidate to realize the enhancement-mode operation. With 0.6-μ m gate length, the devices treated by fluorine plasma for 150-W RF power at 150 s exhibited a threshold voltage of 1.3 V. The maximum drain current and maximum transconductance are 300 mA/mm, and 177 mS/mm, respectively. Compared with the 22-nm barrier E-mode devices, V_T of the thin barrier HEMTs is much more stable under the gate step-stress.     

Characterization and comparison between Ig(Vgs) structures HEMT AlInN/GaN and AlGaN/GaN

In this paper, we have studied the Schottky contact of two structures AlInN/GaN and AlGaN/GaN in transistors HEMTs. The current–voltage Igs(Vgs) of AlInN/GaN and AlGaN/GaN structures were investigated at room temperature. The electrical parameters such as ideality factor (2.3 and 1.96), barrier height (0.72 and 0.71 eV) and series resistance (33 and 153 $\Omega $ ) were evaluated from I–V data. The comparison of the performance of the two structures AlInN/GaN and AlGaN/GaN in transistors HEMTs have been analyzed and discussed.     

AlGaN/GaN高电子迁移率晶体管肖特基高温退火机理研究

在不同应力条件下,研究了AlGaN/GaN高电子迁移率晶体管高温退火前后的电流崩塌、栅泄漏电流以及击穿电压的变化.结果表明,AlGaN/GaN高电子迁移率晶体管通过肖特基高温退火以后,器件的特性得到很大的改善.利用电镜扫描(SEM)和X射线光电子能谱(XPS)对高温退火前、后的肖特基接触界面进行深入分析,发现器件经过高温退火后,Ni和AlGaN层之间介质的去除,并且AlGaN材料表面附近的陷阱减少,使得肖特基有效势垒提高,从而提高器件的电学特性. 关键词： AlGaN/GaN高电子迁移率晶体管 肖特基接触 界面陷阱     

基于原位等离子体氮化及低压化学气相沉积-Si_3N_4栅介质的高性能AlGaN/GaN MIS-HEMTs器件的研究

通过对低压化学气相沉积(LPCVD)系统进行改造,实现在沉积Si_3N_4薄膜前的原位等离子体氮化处理,氮等离子体可以有效地降低器件界面处的氧含量和悬挂键,从而获得了较低的LPCVD-Si_3N_4/GaN界面态,通过这种技术制作的MIS-HEMTs器件,在扫描栅压范围V_(G-sweep)=(-30 V,+24 V)时,阈值回滞为186 mV,据我们所知为目前高扫描栅压V_(G+)(20 V)下的最好结果.动态测试表明,在400 V关态应力下,器件的导通电阻仅仅上升1.36倍(关态到开态的时间间隔为100μs).     

Radiation source dependence of device performance degradation for 4H-SiC MESFETs

The impact of radiation source dependence on the device performance degradation of 4H-SiC MESFETs (Metal Schottky Field Effect Transistors), which have been irradiated at room temperature with 2 MeV electrons and 20 MeV protons, is studied. No performance degradation is observed by 1×10¹⁵ e/cm² and 5×10¹¹ p/cm², while a slight increase of the linear drain current together with a decrease of the threshold voltage are noticed above higher fluence. The damage coefficient for protons is about three orders of magnitude larger than that for electrons. The radiation source dependence of the device performance degradation is attributed to the difference of mass and the possibility of nuclear collision for the formation of lattice defects. Based on thermal annealing results of electron-irradiated MESFETs, it is found that the recovery of the drain current characteristics principally takes place from 100 C, and that the drain current recovers to the pre-rad value after 200 C annealing. On the other hand, capacitance and induced deep levels do not recover by 200 C annealing. It is concluded that the degradation of the drain current is mainly sensitive to the radiation-induced decrease of the Schottky barrier height at the gate contact.