氧压对Ba0.6Sr0.4TiO3薄膜晶格常数的影响及BaTiO3/Ba0.6Sr0.4TiO3超晶格的制备

采用脉冲激光沉积(PLD)技术,经一系列的优化实验成功地制备了BaTiO₃(BT)和Ba_0.6Sr_0.4TiO₃(BST)单层膜.X射线衍射分析表明,在LaAlO₃(001)单晶平衬底上生长的BT和BST薄膜都是沿[001]取向的近外延生长.且随着氧压在10^-3—25 Pa范围内逐渐增大,BST薄膜的晶格常数与氧压之间近似满足Boltzmann函数关系.其次,在此优化条件下还 关键词： 超晶格 晶格常数 激光感生热电电压 脉冲激光沉积     

两种不同(Ba,Sr)TiO3薄膜介电-温度特性的研究

研究并比较了两种不同(Ba_0.5,Sr_0.5)TiO₃(BSTO)薄膜介电-温度特性.采用脉冲激光沉积技术在Pt/Ti/SiO₂/Si(100)衬底上制备BSTO薄膜，发现制备条件的不同，可以得到介电性质完全不同的BSTO薄膜.在550℃和氮气氛下制备的BSTO薄膜在常温下具有很高的介电常数，在10kHz下，超过2500，并在200K温度以上介电常数基本不变.它的一些电学性质不同于在正常条件(650℃和氧气氛下)制得的BSTO薄膜，而类似于目前广泛报道的巨介电常数材料如CaCu_３Ti_４O₁₂.两种薄膜介电性质测试结果表明: 氧气氛下制备的BSTO薄膜呈现铁电-顺电相变，符合居里-外斯定律；低温氮气氛下制备的BSTO薄膜，介电弛豫时间和温度的关系符合德拜模型，是热激发弛豫.文中给出了产生这种介电特性的初步解释. 关键词： 薄膜 脉冲激光沉积 介电弛豫     

两种不同(Ba,Sr)TiO3薄膜介电-温度特性的研究

研究并比较了两种不同(Ba0.5,Sr0.5)TiO3(BSTO)薄膜介电-温度特性.采用脉冲激光沉积技术在Pt/Ti/SiO2/Si(100)衬底上制备BSTO薄膜,发现制备条件的不同,可以得到介电性质完全不同的BSTO薄膜.在550℃和氮气氛下制备的BSTO薄膜在常温下具有很高的介电常数,在10kHz下,超过2500,并在200K温度以上介电常数基本不变.它的一些电学性质不同于在正常条件(650℃和氧气氛下)制得的BSTO薄膜,而类似于目前广泛报道的巨介电常数材料如CaCu3Ti4O12.两种薄膜介电性质测试结果表明: 氧气氛下制备的BSTO薄膜呈现铁电-顺电相变,符合居里-外斯定律;低温氮气氛下制备的BSTO薄膜,介电弛豫时间和温度的关系符合德拜模型,是热激发弛豫.文中给出了产生这种介电特性的初步解释.     

Bi0.8Ba0.2FeO3/La0.7Sr0.3MnO3异质结制备及其交换偏置效应研究

采用脉冲激光沉积方法, 通过调节激光能量、激光频率、衬底温度、氧压、靶基距等工艺参数, 在(100)取向的铝酸镧单晶衬底上制备出Bi_0.8Ba_0.2FeO₃/La_0.7Sr_0.3MnO₃多铁性异质结. X射线衍射图谱表明薄膜呈钙钛矿结构, 高分辨透射电镜图谱和能量色散X射线图谱表明两相界面清晰且具有良好的匹配度, 异质结呈(00l)取向性生长. 加场冷却条件下不同温度的磁滞回线(M-H)测量结果表明样品具有明显的交换偏置效应, 交换偏置场(H_EB)随温度的线性变化可能与异质结界面处电子轨道的重构和界面处自旋、轨道自由度之间的复杂的相互作用有关.     

CaCu3Ti4O12陶瓷的介电特性与弛豫机理

本文采用Novocontrol宽频介电谱仪在-100 ℃–100 ℃温 度范围内、0.1 Hz–10 MHz频率范围内测量了表面层打磨前 后CaCu₃Ti₄O₁₂陶瓷的介电特性, 分析了CaCu₃Ti₄O₁₂陶瓷的介电弛豫机理. 首先, 基于对宏观“壳-心”结构的定量分析, 排除了巨介电常数起源于表面层效应的可能性; 其次, 基于经典Maxwell-Wagner夹层极化及其活化能物理本质的分析, 排除了巨介电常数起源于经典Maxwell-Wagner极化的可能性; 最后, 依据晶界Schottky势垒与本征点缺陷的本质联系, 提出了巨介电常数起源于Schottky势垒边界陷阱电子弛豫的新机理. 陷阱电子弛豫机理反映了CaCu₃Ti₄O₁₂陶瓷本征点缺陷、 电导、介电常数之间的本质关系. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电弛豫 Schottky势垒 点缺陷     

溶胶-凝胶法制备的Ba0.8Sr0.2TiO3薄膜的结构及铁电性质研究

采用0.05mol/L的前驱体溶液,利用溶胶-凝胶法成功制备了室温下具有优良铁电性质的Ba_0.8Sr_0.2TiO₃ (BST)薄膜.X射线衍射分析表明,制得的BST薄膜室温下呈四方相,场发射扫描电子显微观测显示BST薄膜表面平整、致密、无裂纹出现,薄膜晶粒呈柱状结构、尺寸在150nm左右.电学测量表明制备的BST薄膜室温下具有优良的铁电性能.薄膜的剩余极化P_r约为35μC/cm²,矫顽电场E关键词：     

氧压对SrTiO3和SrNb0.2Ti0.8O3薄膜晶格参数的影响及激光感生热电电压效应

采用脉冲激光沉积技术制备了SrTiO₃和SrNb_0.2Ti_0.8O₃薄膜.X射线衍射分析表明在LaAlO₃(100)单晶平衬底上生长的SrTiO₃及SrNb_0.2Ti_0.8O₃薄膜是沿［001］取向的近外延生长.随着氧压在一定范围内逐渐增大,SrTiO₃薄膜的晶格参数减小,而SrNb_0.2Ti_0.8O₃薄膜的晶格参数先减小后增大.同时摸索出制备具有二维电子气超晶格(SrTiO₃/SrNb_0.2Ti_0.8O₃)_L的最佳氧压为1.0×10^-2Pa.另外在LaAlO₃(100)倾斜衬底上制备的SrNb_0.2Ti_0.8O₃薄膜中观察到激光感生热电电压效应. 关键词： 0.2Ti_0.8O₃薄膜')" href="#">SrNb_0.2Ti_0.8O₃薄膜 晶格参数 激光感生热电电压 脉冲激光沉积     

La诱导(Pb(1-3x/2)Lax)(Zr0.5Sn0.3Ti0.2)O3反铁电介电弛豫研究

采用标准电子陶瓷工艺制备了(Pb_(1-3x/2)La_x)(Zr_0.5Sn_0.3Ti_0.2)O₃(PLZST,0.00≤x≤0.18)反铁电陶瓷,利用X射线衍射、不同频率下弱场介电温谱、强场下的极化强度-电场(P-E)测试研究了材料相结构和电学性能.实验结果发现,随La含量x增大,室温下材料由铁电三方相(关键词： 反铁电陶瓷 介电频率色散 相变弥散 介电弛豫     

La2/3Sr1/3MnO3/BaTiO3复合薄膜的制备及其电致磁电效应研究

使用脉冲激光沉积技术,在LaAlO₃(001)单晶基片上制备了La_2/3Sr_1/3MnO₃(LSMO)/BaTiO₃(BTO)双层薄膜.X射线衍射分析显示,LSMO层和BTO层呈现纯(001)取向.原子力显微镜研究表明,薄膜表面晶粒大小均匀,排列致密,表面均方根粗糙度为1.4 nm.复合薄膜的磁学、电学性能研究表明,其具有良好的磁学和介电性能.电输运测试显示,与在BTO层上施加正方向 关键词： 磁电效应 铁电/铁磁异质结构 脉冲激光沉积     

淀积气压对脉冲激光淀积La掺杂钛酸铅薄膜介电性能的影响

利用脉冲激光淀积法在Pt/Ti/SiO2/Si衬底上制备了28mol%La掺杂钛酸铅薄膜.采用不同的淀积氧气压，并分析了其对薄膜微观结构和介电性能的影响.结果表明，在2Pa左右的气压下淀积的薄膜具有好的结晶度和介电系数.在频率为10kHz时28mol%La掺杂钛酸铅薄膜的介电系数达852，并且保持了较低的损耗.同时制备了其他La掺杂浓度的PbTiO3薄膜，发现它们也有类似的特点.对此作了定性解释. 关键词： 脉冲激光淀积 PLT薄膜 气压 介电增强     

Effects of oxygen partial pressure on the ferroelectric properties of pulsed laser deposited Ba0.8Sr0.2TiO3 thin films

The Ba_0.8Sr_0.2TiO₃ thin films were grown on the Pt–Si substrate at 700 °C by using a pulsed laser deposition technique at different oxygen partial pressure (PO₂) in the range of 1–20 Pa and their properties were investigated. It is observed that the PO₂ during the deposition plays an important role on the tetragonal distortion ratio, surface morphology, dielectric permittivity, ferroelectric polarization, switching response, and leakage currents of the films. With an increase in PO₂, the in-plane strain for the BST films changes from tensile to compressive. The films grown at 7.5 Pa show the optimum dielectric and ferroelectric properties and also exhibit the good polarization stability. It is assumed that a reasonable compressive strain, increasing the ionic displacement, and thus promotes the in-plane polarization in the field direction, could improve the dielectric permittivity. The butterfly features of the capacitance–voltage (C–V) characteristics and the bell shape curve in polarization current were attributed to the domain reversal process. The effect of pulse amplitude on the polarization reversal behavior of the BST films grown at PO₂ of 7.5 Pa was studied. The peak value of the polarization current shows exponential dependence on the electric field.     

Improved dielectric and electrical properties of (Ba,Sr)TiO3 thin films using Pt/LaNiO3 as the top-electrode material

(Ba,Sr)TiO₃ (BST) capacitors grown on a LaNiO₃ (LNO) bottom electrode, with Pt (80 nm), LNO (100 nm), and double-layer Pt/LNO (80/10 nm) top electrodes have been investigated. It was found that the dielectric behavior is improved by a decrease of the electrical properties for the BST capacitor using double-layer Pt/LNO top electrodes. The dielectric constant of 100 nm-thick BST films with a Pt electrode was only 165 at 100 kHz, while that with a double-layer electrode was about 242. Correspondingly, the tunability was greatly improved from 26% to 41% with an electric field of 600 kV/cm. These have been attributed to increased interfacial capacitance density, which resulted from an improved interface, between the films and the top electrode. The dielectric loss was also reduced by using a double-layer electrode. Furthermore, the leakage current of a capacitor with a double-layer Pt/LNO electrode was one order of magnitude lower than that with a single LNO electrode. It can be explained by the fact that the weak chemical interaction between LNO (10 nm) and BST causes a high potential barrier at the interface. PACS 81.15.-z; 81.15.Cd; 77.55.+f; 77.84.Dy; 77.22.-d     

The effect of spin relaxation on ENDOR spectra recorded at high magnetic fields and low temperatures

A simple theoretical model that describes the pulsed Davies electron-nuclear double resonance (ENDOR) experiment for an electron spin S = (1/2) coupled to a nuclear spin I = (1/2) was developed to account for unusual W-band (95 GHz) ENDOR effects observed at low temperatures. This model takes into account the thermal polarization along with all internal relaxation processes in a four-level system represented by the electron- and nuclear-spin relaxation times T(1e) and T(1n), respectively, and the cross-relaxation time, T(1x). It is shown that under conditions of sufficiently high thermal spin polarization, nuclei can exhibit asymmetric ENDOR spectra in two cases: the first when t(mix) > T(1e) and T(1n), T(1x) > T(1e), where ENDOR signals from the alpha manifold are negative and those of the beta manifold positive, and the second when the cross- and/or nuclear-relaxation times are longer than the repetition time (t(mix) < T(1e) < t(R) and T(1n), T(1x) > t(R)). In that case the polarization of the ENDOR signals becomes opposite to the previous case, the lines in the alpha manifolds are positive, and those of the beta manifold are negative. This case is more likely to be encountered experimentally because it does not require a very long mixing time and is a consequence of the saturation of the nuclear transitions. Using this model the experimental t(mix) and t(R) dependencies of the W-band (1)H ENDOR amplitudes of [Cu(imidazole)(4)]Cl(2) were reproduced and the values of T(1e) and T(1x) > T(1e) were determined. The presence of asymmetry in the ENDOR spectrum is useful as it directly provides the sign of the hyperfine coupling. The presented model allows the experimentalist to adjust experimental parameters, such as t(mix) and t(R), in order to optimize the desired appearance of the spectrum.     

Magnetostatic Coupling in Ba0.8Sr0.2TiO3/CoFe2O4 Magnetoelectric Composite Thin Films of 2-2-Type Structure

Ba0.8Sr0.2 TiO3/CoFe2O4 （BST/CFO） magnetoelectric composite thin films of 2-2-type structures are prepared onto Pt/Ti/SiO2/Si substrates by a sol-gel process and spin coating technique. The structure of the prepared thin film is substrate/BST/CFO/. . ./CFO/BST. Three CFO ferromagnetic layers are separated from each other by a thin BST layer. The upper CFO layer is magnetostatically coupled with the lower CFO layer. Subsequent scanning electron microscopy investigations show that the prepared thin films exhibit good morphologies and have a compact structure, and the cross-sectional mierographs clearly display a multilayered nanostructure of multilayered thin films. The composite thin films exhibit good magnetic and ferroelectric properties. The spacing between ferromagnetic layers can be varied by adjusting the thickness of intermediate BST layer. It is found that the strength of magnetostatic coupling has a great impact on magnetoelectric properties of composite thin film; that is, the magnetoelectric voltage coefficient of the composite thin film tends to increase with the decrease of pacing between two neighboring CFO ferromagnetic layers as a result of magnetostatic coupling effect.     

Relaxor characteristics of highly tunable lead-free 0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3)TiO3 thin film grown on LaNiO3/Si by pulsed laser deposition

We report a comprehensive study on relaxor-like characteristics exhibited by (l00) oriented 0.5Ba(Zr_0.2Ti_0.8)O₃–0.5(Ba_0.7Ca_0.3)TiO₃ thin film grown on LaNiO₃ coated Si substrate by pulsed laser deposition. The diffuseness coefficient value close to 2 and excellent fit of Vogel–Fulcher curve to the experimental data, suggest its relaxor characteristics. The ‘butterfly’ shaped dc field dependence of permittivity and evolution of P–E hysteresis loop, at different temperatures, clearly indicate the occurrence of polar nanoregions in this material. The high tunability n_r ～ 70 and low temperature coefficient TCC = 5.18 × 10^?4 K^?1 show that the BCZT50 ceramics could be a promising candidate for tunable capacitor applications.     

Surface-layer effect in MnTiO3 ceramics at low temperatures

MnTiO₃ ceramics were prepared via the traditional solid-state reaction route. The low-temperature (100–330 K) dielectric properties of MnTiO₃ have been systematically investigated in the frequency range from 100 Hz to 5 MHz. Our results showed that MnTiO₃ exhibits intrinsic dilectric response in a wide temperature range up to 200 K. A relaxation appears near room temperature. This relaxation can be enhanced by annealing treatment in oxygen and weakened in nitrogen. Reducing the sample thickness gradually leads to the disappearance of the relaxation. Based on these experimental facts, the relaxation was ascribed to be a Maxwell–Wagner relaxation due to surface-layer effect.