增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

The effects of ⁶⁰Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

High-frequency enhancement-mode millimeterwave AlGaN/GaN HEMT with an fT/fmax over 100 GHz/200 GHz

Ultra-thin barrier (UTB) 4-nm-AlGaN/GaN normally-off high electron mobility transistors (HEMTs) having a high current gain cut-off frequency (f_T) are demonstrated by the stress-engineered compressive SiN trench technology. The compressive in-situ SiN guarantees the UTB-AlGaN/GaN heterostructure can operate a high electron density of 1.27×10¹³cm^-2, a high uniform sheet resistance of 312.8 Ω /□, but a negative threshold for the short-gate devices fabricated on it. With the lateral stress-engineering by full removing in-situ SiN in the 600-nm SiN trench, the short-gated (70 nm) devices obtain a threshold of 0.2 V, achieving the devices operating at enhancement-mode (E-mode). Meanwhile, the novel device also can operate a large current of 610 mA/mm and a high transconductance of 394 mS/mm for the E-mode devices. Most of all, a high f_T/f_max of 128 GHz/255 GHz is obtained, which is the highest value among the reported E-mode AlGaN/GaN HEMTs. Besides, being together with the 211 GHz/346 GHz of f_T/f_max for the D-mode HEMTs fabricated on the same materials, this design of E/D-mode with the realization of f_max over 200 GHz in this work is the first one that can be used in Q-band mixed-signal application with further optimization. And the minimized processing difference between the E- and D-mode designs the addition of the SiN trench, will promise an enormous competitive advantage in the fabricating costs.     

The effects of 60Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

Recessed-gate quasi-enhancement-mode AlGaN/GaN high electron mobility transistors with oxygen plasma treatment

In this paper,the enhancement-mode AlGaN/GaN HEMT combined with the low damage recessed-gate etching and the optimized oxygen plasma treatment was fabricated.Scanning electron microscope/energy dispersive spectrometer(SEM/EDS) method and x-ray photoelectron spectroscopy(XPS) method were used to confirm the formation of oxides.Based on the experimental results,the obtained enhancement-mode HEMT exhibited a threshold voltage of 0.5 V,a high peak transconductance of 210 mS/mm,and a maximum drain current of 610 mA/mm at the gate bias of 4 V.Meanwhile,the on/off current ratio of enhancement-mode HEMT was as high as 10~8,drain induced barrier lowering(DIBL) was as low as 5 raV/V,and subthreshold swing(SS) of 80 mV/decade was obtained.Compared with the conventional HEMT,the Schottky reverse current of enhancement-mode HEMT was three orders of magnitude lower,and the off-state breakdown voltage of which was higher.In addition,a power gain cutoff frequency(/max) of the enhancement-mode HEMT was larger than that of the conventional one.     

Non-recessed-gate quasi-E-mode double heterojunction AlGaN/GaN high electron mobility transistor with high breakdown voltage

A non-recessed-gate quasi-E-mode double heterojunction AlGaN/GaN high electron mobility transistor(quasi-EDHEMT) with a thin barrier, high breakdown voltage and good performance of drain induced barrier lowering(DIBL)was presented. Due to the metal organic chemical vapor deposition(MOCVD) grown 9-nm undoped AlGaN barrier, the effect that the gate metal depleted the two-dimensiomal electron gas(2DEG) was greatly impressed. Therefore, the density of carriers in the channel was nearly zero. Hence, the threshold voltage was above 0 V. Quasi-E-DHEMT with 4.1-μm source-to-drain distance, 2.6-μm gate-to-drain distance, and 0.5-μm gate length showed a drain current of 260 mA/mm.The threshold voltage of this device was 0.165 V when the drain voltage was 10 V and the DIBL was 5.26 mV/V. The quasi-E-DHEMT drain leakage current at a drain voltage of 146 V and a gate voltage of-6 V was below 1 mA/mm. This indicated that the hard breakdown voltage was more than 146 V.     

AlGaN/GaN双异质结F注入增强型高电子迁移率晶体管

理论模拟了不同GaN沟道厚度的双异质结(AlGaN/GaN/AlGaN/GaN)材料对高电子迁移率晶体管(HEMT)特性的影响,并模拟了不同F注入剂量下用该材料制作的增强型器件的特性差异.采用双异质结材料,结合F注入工艺成功地研制出了较高正向阈值电压的增强型HEMT器件.实验研究了三种GaN沟道厚度制作的增强型器件直流特性的差异,与模拟结果进行了对比验证.采用降低的F注入等离子体功率,减小了等离子体处理工艺对器件沟道迁移率的损伤,研制出的器件未经高温退火即实现了较高的跨导和饱和电流特性.对14 nm GaN沟道厚度的器件进行了阈值电压温度稳定性和栅泄漏电流的比较研究,并且分析了双异质结器件的漏致势垒降低效应.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

AlGaN/GaN high-electron-mobility transistors with transparent gates by Al-doped ZnO

AlGaN/GaN high-electron-mobility transistors （HEMTs） with Al-doped ZnO （AZO） transparent gate electrodes are fabricated, and Ni/Au/Ni-gated HEMTs are produced in comparison. The AZO-gated HEMTs show good DC characteristics and Schottky rectifying characteristics, and the gate electrodes achieve excellent transparencies. Compared with Ni/Au/Ni-gated HEMTs, AZO-gated HEMTs show a low saturation current, high threshold voltage, high Schottky barrier height, and low gate reverse leakage current. Due to the higher gate resistivity, AZO-gated HEMTs exhibit a current-gain cutoff frequency （fT） of 10 GHz and a power gain cutoff frequency （fmax） of 5 GHz, and lower maximum oscillation frequency than Ni/Au/Ni-gated HEMTs. Moreover, the C-V characteristics are measured and the gate interface characteristics of the AZO-gated devices are investigated by a C-V dual sweep.     

Normally-off metamorphic AlInAs/AlInAs HEMTs on Si substrates grown by MOCVD

A combination of self-aligned fluoride-based plasma treatment and post-gate rapid thermal annealing was developed to fabricate a novel 120-nm T-shaped gate normally-off metamorphic Al0.49In0.51As/Ga0.47In0.53 As HEMT device on a Si substrate grown by metal-organic chemical vapor deposition(MOCVD). A shift of the threshold voltage, from-0.42 V to 0.11 V was obtained and the shift can be effectively adjusted by the process parameter of CF4 plasma treatment. Furthermore, a side benefit of reducing the leakage current of the device up to two orders of magnitude was also observed.E-mode transistors with 120 nm gate length own fTup to 160 GHz and fmax of 140 GHz. These characteristics imply the potential of the fluoride-based plasma treatment technology for the fabrication of monolithic enhancement/depletion-mode m HEMTs, which also encourage the massive production with this low-cost technology.     

A novel Si-rich SiN bilayer passivation with thin-barrier AlGaN/GaN HEMTs for high performance millimeter-wave applications

We demonstrate a novel Si-rich SiN bilayer passivation technology for AlGaN/GaN high electron mobility transistors (HEMTs) with thin-barrier to minimize surface leakage current to enhance the breakdown voltage. The bilayer SiN with 20-nm Si-rich SiN and 100-nm Si$_{3}$N$_{4}$ was deposited by plasma-enhanced chemical vapor deposition (PECVD) after removing 20-nm SiO$_{2}$ pre-deposition layer. Compared to traditional Si$_{3}$N$_{4}$ passivation for thin-barrier AlGaN/GaN HEMTs, Si-rich SiN bilayer passivation can suppress the current collapse ratio from 18.54% to 8.40%. However, Si-rich bilayer passivation leads to a severer surface leakage current, so that it has a low breakdown voltage. The 20-nm SiO$_{2}$ pre-deposition layer can protect the surface of HEMTs in fabrication process and decrease Ga-O bonds, resulting in a lower surface leakage current. In contrast to passivating Si-rich SiN directly, devices with the novel Si-rich SiN bilayer passivation increase the breakdown voltage from 29 V to 85 V. Radio frequency (RF) small-signal characteristics show that HEMTs with the novel bilayer SiN passivation leads to $f_{\rm T}/f_{\rm max}$ of 68 GHz/102 GHz. At 30 GHz and $V_{\rm DS} = 20$ V, devices achieve a maximum $P_{\rm out}$ of 5.2 W/mm and a peak power-added efficiency (PAE) of 42.2%. These results indicate that HEMTs with the novel bilayer SiN passivation can have potential applications in the millimeter-wave range.     

Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

Fluorine-plasma treated AlGaN/GaN high electronic mobility transistors under off-state overdrive stress

Influences of off-state overdrive stress on the fluorine-plasma treated AlGaN/GaN high-electronic mobility transistors (HEMTs) are experimentally investigated. It is observed that the reverse leakage current between the gate and source decreases after the off-state stress, whereas the current between the gate and drain increases. By analyzing those changes of the reverse currents based on the Frenkel-Poole model, we realize that the ionization of fluorine ions occurs during the off-state stress. Furthermore, threshold voltage degradation is also observed after the off-state stress, but the degradations of AlGaN/GaN HEMTs treated with different F-plasma RF powers are different. By comparing the differences between those devices, we find that the F-ions incorporated in the GaN buffer layer play an important role in averting degradation. Lastly, suggestions to obtain a more stable fluorine-plasma treated AlGaN/GaN HEMT are put forwarded.     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

高场应力及栅应力下AlGaN/GaN HEMT器件退化研究

采用不同的高场应力和栅应力对AlGaN/GaN HEMT器件进行直流应力测试,实验发现：应力后器件主要参数如饱和漏电流,跨导峰值和阈值电压等均发生了明显退化,而且这些退化还是可以完全恢复的;高场应力下,器件特性的退化随高场应力偏置电压的增加和应力时间的累积而增大;对于不同的栅应力,相对来说,脉冲栅应力和开态栅应力下器件特性的退化比关态栅应力下的退化大.对不同应力前后器件饱和漏电流,跨导峰值和阈值电压的分析表明,AlGaN势垒层陷阱俘获沟道热电子以及栅极电子在栅漏间电场的作用下填充虚栅中的表面态是这些不同应 关键词： AlGaN/GaN HEMT器件 表面态(虚栅) 势垒层陷阱 应力     

High-electric-field-stress-induced degradation of SiN passivated AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) are fabricated by employing SiN passivation, this paper investigates the degradation due to the high-electric-field stress. After the stress, a recoverable degradation has been found, consisting of the decrease of saturation drain current I_Dsat, maximal transconductance g_m, and the positive shift of threshold voltage V_TH at high drain-source voltage V_DS. The high-electric-field stress degrades the electric characteristics of AlGaN/GaN HEMTs because the high field increases the electron trapping at the surface and in AlGaN barrier layer. The SiN passivation of AlGaN/GaN HEMTs decreases the surface trapping and 2DEG depletion a little during the high-electric-field stress. After the hot carrier stress with V_DS=20 V and V_GS=0 V applied to the device for 10⁴ sec, the SiN passivation decreases the stress-induced degradation of I_Dsat from 36% to 30%. Both on-state and pulse-state stresses produce comparative decrease of I_Dsat, which shows that although the passivation is effective in suppressing electron trapping in surface states, it does not protect the device from high-electric-field degradation in nature. So passivation in conjunction with other technological solutions like cap layer, prepassivation surface treatments, or field-plate gate to weaken high-electric-field degradation should be adopted.     

Low power fluorine plasma effects on electrical reliability of AlGaN/GaN high electron mobility transistor

The new electrical degradation phenomenon of the AlGaN/GaN high electron mobility transistor(HEMT) treated by low power fluorine plasma is discovered. The saturated current, on-resistance, threshold voltage, gate leakage and breakdown voltage show that each experiences a significant change in a short time stress, and then keeps unchangeable. The migration phenomenon of fluorine ions is further validated by the electron redistribution and breakdown voltage enhancement after off-state stress. These results suggest that the low power fluorine implant ion stays in an unstable state. It causes the electrical properties of AlGaN/GaN HEMT to present early degradation. A new migration and degradation mechanism of the low power fluorine implant ion under the off-stress electrical stress is proposed. The low power fluorine ions would drift at the beginning of the off-state stress, and then accumulate between gate and drain nearby the gate side. Due to the strong electronegativity of fluorine, the accumulation of the front fluorine ions would prevent the subsequent fluorine ions from drifting, thereby alleviating further the degradation of AlGaN/GaN HEMT electrical properties.     

Effect of heavy ion irradiation on the interface traps of AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were irradiated with heavy ions at various fluences. After irradiation by 2.1 GeV¹⁸¹ Ta³²⁺ ions, the electrical characteristics of the devices significantly decreased. The threshold voltage shifted positively by approximately 25% and the saturation currents decreased by approximately 14%. Defects were induced in the band gap and the interface between the gate and barrier acted as tunneling sites, which increased the gate current tunneling probability. According to the pulsed output characteristics, the amount of current collapse significantly increased and more surface state traps were introduced after heavy ion irradiation. The time constants of the induced surface traps were mainly less than 10 μs.     

Sodium beta-alumina thin films as gate dielectrics for A1GaN/GaN metal-insulator-semiconductor high-electron-mobility transistors

<正>Sodium beta-alumina（SBA） is deposited on AlGaN/GaN by using a co-deposition process with sodium and Al₂O₃ as the precursors.The X-ray diffraction（XRD） spectrum reveals that the deposited thin film is amorphous.The binding energy and composition of the deposited thin film,obtained from the X-ray photoelectron spectroscopy（XPS） measurement,are consistent with those of SBA.The dielectric constant of the SBA thin film is about 50.Each of the capacitance-voltage characteristics obtained at five different frequencies shows a high-quality interface between SBA and AlGaN.The interface trap density of metal-insulator-semiconductor high-electron-mobility transistor（MISHEMT） is measured to be（3.5～9.5）×10¹⁰ cm^-2·eV^-1 by the conductance method.The fixed charge density of SBA dielectric is on the order of 2.7×10¹² cm^-2.Compared with the AlGaN/GaN metal-semiconductor heterostructure high-electronmobility transistor（MESHEMT）,the AlGaN/GaN MISHEMT usually has a threshold voltage that shifts negatively. However,the threshold voltage of the AlGaN/GaN MISHEMT using SBA as the gate dielectric shifts positively from—5.5 V to—3.5 V.From XPS results,the surface valence-band maximum（VBM-E_F） of AlGaN is found to decrease from 2.56 eV to 2.25 eV after the SBA thin film deposition.The possible reasons why the threshold voltage of AlGaN/GaN MISHEMT with the SBA gate dielectric shifts positively are the influence of SBA on surface valence-band maximum （VBM-E_F）,the reduction of interface traps and the effects of sodium ions,and/or the fixed charges in SBA on the two-dimensional electron gas（2DEG）.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.