抗冰导管架平台动力特性分析

目前的抗冰导管架平台结构设计主要是考虑极限冰力引起的破坏,尚未形成基于动冰力响应分析的结构设计。为了更好研究冰荷载、冰激振动机理以及提出合理的概念设计,冰荷载下抗冰导管架结构的动力特性分析是十分必要的。基于现场冰与导管架结构相互作用的多年观测以及数值模拟研究,分析渤海辽东湾典型导管架结构在交变冰力作用下的动力特性,提出了适于冰荷载研究与抗冰导管架结构概念设计、分析的简化力学模型,解释柔性抗冰导管架结构动力效应显著的原因。     

海冰静力作用的特点及几种典型结构的冰力模型试验

海冰静力作用的重要特点是它对结构破坏程度的严重性以及对环境和结构条件的敏感性。冰力模型试验是流体模型试验,又是材料模型试验,所以要遵循特殊的模型律。本文介绍的几项冰力模型试验不仅证实了常被设计者忽略的直立桩柱前冰排的挤压破坏中常不同程度地包括有压屈破坏的成分,而且也证实了直立墙前冰排主要是压屈破坏,斜墙前冰排主要是弯曲破坏。同时给出了这些结构上冰力的量值。     

锥体冰力的实验研究

通过冰力模型试验,研究了锥体冰力的特征和锥间距对冰力的影响。试验发现冰在正-倒锥交界线上的破坏为挤压破坏;根据试验数据给出了冰在双锥前的非同时破坏系数。     

基于水下光纤应变监测的导管架结构总冰力测量方法

基于测量结构水下光纤应变获取冰力的方法首次应用于渤海JZ20-2NW加锥导管架平台,该方法方便进行零点标定,可获取结构总冰力的绝对信息(包括均值和波动值)。首先介绍了JZ20-2NW平台的现场监测系统,主要包括结构水下应变响应记录冰力信息,甲板上部视频记录同步冰情(冰厚、冰速和来冰方向)信息和拾振器记录结构冰振响应;重点分析了由测点应变向结构总冰力的转化方法,并对总冰力进行了初步分析。将无量纲化实测冰力与5种典型冰力计算模型进行了比较,分析结果表明,锥体宽度与海冰厚度比值(简称"宽厚比")对冰力大小及变化起决定作用。     

自升式平台冰激动力响应分析

应用ANSYS软件建立了平台和冰相互作用的有限元模型,构建了自升式平台的冰激振动模型,并计算基于2种冰力模型的自升式平台的动力响应。此动力分析方法具有建模方便和计算精度高的特点。以某自升式平台为例,计算了冰和平台结构相互作用的耦合效应,为自升式平台冰激振动安全评估提供了参考依据。     

精细积分在冰荷载识别中应用

冰激振动中引起的动冰力一直是很受关注的问题。根据精细积分法的基本原理,假定外荷载在离散时间步长内按线性变化,给出了一种冰载荷时域识别方法。经数值算例仿真以及在室内开展的冰激桥墩振动模型试验冰荷载反演的结果表明,该方法形式简洁明了,计算量小,应用方便,特别适宜于计算机求解,具有一定的理论意义和实用价值。     

冰激振动及冰荷载动力特性的试验研究

回顾了解决海冰引起结构振动分析方法的要求，通过室内冰力模型试验得出了冰激振动的重要参数－冰力频率，幅值的特性。研究表明，在低冰速时，冰力频率与冰速对冰厚之比呈线性关系；高冰速时，冰力步与冰速对冰厚之比呈现恒定性，文章还根据试验数据以及统计分析，推荐了冰力幅值计算公式和取值范围。     

孤立桩柱上冰压力的经验公式计算法及试验验证

本文简要介绍了冰排在桩柱前挤压破坏和压屈破坏的判别、冰排运动的驱动力,然后比较了各国常用的一些计算冰力的经验公式,推荐了公式,并推荐了公式中系数的取值法,最后通过冰力模拟试验,验证了所推荐公式和系数取值法的正确性。     

基于黏聚单元法的抗冰海洋平台与层冰相互作用数值模拟

通过商业有限元软件LS-DYNA采用黏聚单元法模拟层冰的断裂问题,在IIHR冰池模型试验相同缩尺比参数下对KULLUK抗冰平台受到的冰力进行数值计算,探究冰厚与冰速等冰况参数对平台冰力的影响。计算结果表明,在极地作业平台主要遭遇北极海域冰况范围下,相同冰厚情况时冰速变化对倒锥形结构平台的横向冰力影响不大,而同冰速时冰力随着冰厚的增加接近线性增加。同时将计算所得结果与同条件下IIHR冰池模型试验数据、ARCTEC、ACL非冻结模型冰试验数据、实船数据和通过ISO19906规范中提供的针对大锥面结构受到层冰冰力的经验公式计算所得数据等进行了对比,验证了选用冰参数的可靠性以及该数值模型在模拟大尺度宽锥形平台遭受层冰作用问题中的适用性。     

渤海海域单柱三桩式海上风电结构冰激振动分析

针对渤海某区域以单柱三桩式结构为支撑的海上风电系统进行了冰激振动分析。首先模拟风电结构具有显著动力特性差异的主-从式结构特征,根据工程场址海域冰情条件,设置了合理的海冰分析工况,随后依据概化冰力函数确定作用于风电基础结构上的动冰力时程,开展全时域瞬态动力分析。通过对计算结果的详尽分析,选定表征冰与风电结构相互作用进程的综合控制因子Ic,建立基于综合控制因子的冰振事件区划及其出现概率的预判方法。相关方法将为渤海海域风电工程结构冰激振动问题的预判与评估提供参考。     

Fatigue Crack Propagation in Steel A131 Under Ice Loading of Crushing,Bending and Buckling

Three types of ice loading, which are most commonly present when ice acts on structures, are chosen and simulated for use of fatigue crack propagation tests on offshore structural steel A131. The three types of ice categorized in accordance with the failure modes when acting on structures called crushing ice, bending ice, and buckling ice, respectively. This paper presents an experimental investigation on the fatigue crack propagation behavior of widely used high strength steel A131 for offshore jackets in the loading environment of ice crushing, bending, and buckling. The test results of fatigue crack propagation in steel A131 under these simulated ice loading at temperature 292K. are presented and analyzed in detail in this paper. The amplitude root mean square stress intensity factor is optimized to be the fundamental parameter of fatigue crack propagation for all types of ice loading histories. The results are also compared with constant amplitude fatigue crack propagation conclusions as in wave loa     

基于实测动冰力时程的海洋平台结构冰振反应分析

冰激平台结构振动是影响渤海石油钻采平台冬季正常生产和安全的主要因素。本文采用实测冰压力时程,对渤海辽东湾北部的ＪＺ２０－２ＭＵＱ平台结构进行了冰振反应分析,计算了不同设计冰厚、不同冰作用方向和标高及平台桩腿有无正倒锥体（一种破冰装置）的结构反应,探讨了正倒锥体对减轻冰力和结构反应的作用,发现了结构冰激振动的一些特征,为在该平台上实施振动控制方案提供了依据     

Mitigation of Ice-Induced Vibrations for Offshore Platforms Using Tuned Mass Damper

The problems of ice-induced vibration have been noticed and concerned since the 1960s, but it has not been well resolved. One reason is that the dynamic interaction between ice and structure is so complicated that practical ice force model has not been developed. The recent full-scale tests conducted on jacket platforms in the Bohai Sea presented that ice could cause intense vibrations which endanger the facilities on the deck and make discomfort for the crew. In this paper, the strategy of mitigation of ice-induced offshore structure vibration is discussed. Based on field observations and understanding of the interaction between ice and structure, the absorption mitigation method to suppress ice-induced vibration is presented. The numerical simulations were conducted for a simplified model of platform attached with a Tuned Mass Danlper （TMD） under ice force function and ice force time history. The simulation results show that TMD can fa- vorably reduce ice-induced vibrations, therefore, it can be considered to be an alternative approach to utilize. Finally, the application possibilities of utilizing TMDs on other miniature offshore structures in ice-covered areas of marginal oil fields are discussed.     

An Experimental Study of Several Special Issues Regarding the Ice Force on Conical Structures

The effect of the cone spacing of a conieal structure on the ice force is studied by model experiments. The ice force reduction coefficient presented in this paper expresses the relationship between the ice force and the arrangement of cones. The experiments prove that the mode of the ice failure before the boundary of upward-downward bending cone (UDBC) is crushing. A conclusion can also be drawn from the experiments that the ice force on the boundary of UDBC is by far less than that on a vertical pile with the same diameter. Moreover, the ice force frequencies on upright and inve-rted cones are obtained under the field condition of the platform JZ20-2, respectively. The results show that the alterna-tion of the ice force on UDBC can hardly induce resonance of platform JZ20-2.     

渤海导管架平台桩柱冰压力随机过程模型及其参数确定

首先分析了冰压力随机过程的特征及其产生机理,从而按冰的破坏形式将冰压力随机过程分为挤压破坏过程、屈曲破坏过程和弯曲破坏过程.从渤海海冰对平合桩柱作用大量实测冰压力曲线中选取37条典型的冰挤压破坏时程曲线,经谱分析确定了相应冰压力随机过程的谱密度及其谱参数;进一步经统计分析,建立了谱参数与冰厚的关系;在此基础上,建立了绕圆桩柱的冰压力随机场模型,并利用大量实测数据,经统计回归分析,确定了场函数的具体表达形式,由此用冰压力随机场可以容易地确定圆桩柱的总冰压力随机过程及其谱密度.     

作用于平台桩腿的海冰屈曲破坏冰压力随机过程模型及其参数确定

冰对结构的作用过程是典型的随机过程。本文在冰压力过程为平稳过程的假设下，从渤海海冰对平台桩腿作用的大量实测冰压力数据中，选取了２１条冰屈曲破坏时的冰压力时程曲线，对它们进行谱分析后，得到了单点冰屈曲破坏的压力随机过程的谱密度，并确定了谱参数及其跟环境要素的关系，依据文献［１］中冰压力沿圆柱面的空间分布，建立了绕桩腿的冰压力随机场模型，并得到了作用于桩腿的总冰力随机过程及其谱密度。本文的研究成果为平台结构冰激随机振动和疲劳累积损伤分析提供了荷载基础     

Model Test Study on Ice Induced Vibration of A Compliant Conical Structure

1.Introduction Inthedesignofoceanengineeringstructuresforcoldregioncountries,iceloadsarealwaysthe controlloads,andthedesignofice resistingstructuresisoneoftheimportantdesignaspects.Fornat uralseaice,theflexuralstrengthisalwaysonethirdofthecompressivestrength.Soconicalstructures thatcouldinducethebendingfailureoficesheetsarewidelyusedinthedesignsofice resistingstruc tures.Forexample,theplatformKullukintheBeaufortSeaisaninvertedconicalstructure,andan upward downwardbendingconeisusedonplatformJ…     

GPU-Based DEM Simulations of Global Ice Resistance on Ship Hull During Navigation in Level Ice

The ice resistance on a ship hull affects the safety of the hull structure and the ship maneuvering performance in icecovered regions.In this paper,the discrete element method(DEM)is adopted to simulate the interaction between level ice and ship hull.The level ice is modeled with 3D bonded spherical elements considering the buoyancy and drag force of the water.The parallel bonding approach and the de-bonding criterion are adopted to model the freezing and breakage of level ice.The ship hull is constructed with rigid triangle elements.To improve computational efficiency,the GPU-based parallel computational algorithm was developed for the DEM simulations.During the interaction between the ship hull and level ice,the ice cover is broken into small blocks when the interparticle stress approaches the bonding strength.The global ice resistance on the hull is calculated through the contacts between ice elements and hull elements during the navigation process.The influences of the ice thickness and navigation speed on the dynamic ice force are analyzed considering the breakage mechanism of ice cover.The Lindqvist and Riska formulas for the determination of ice resistance on ship hull are employed to validate the DEM simulation.The comparison of results of DEM,Lindqvist,and Riska formula show that the DEM result is between those the Lindqvist formula and Riska formula.Therefore the proposed DEM is an effective approach to determine the ice resistance on the ship hull.This work can be aided in the hull structure design and the navigation operation in ice-covered fields.