Improved Kinetic Rate Constants for Nylon 6, Nylon 6,6, and Nylon 6/6,6 Copolymer

Nylon 6 and 6,6 literature data are collected over a wide range of water concentrations and temperatures (0 ≤ [W]₀ ≤ 40.8 wt%, 200 ≤ T ≤300 °C) and used to fit parameters in an updated batch reactor model. The resulting copolymerization model uses side reactions to account for the complex influence of water on kinetics and reaction equilibria. The proposed parameter estimates result in a significant improvement in the fit to the data, corresponding to a 73% reduction in the weighted‐least‐squares objective function compared to when the parameters of Arai et al. are used. Copolymerization simulations are conducted at industrially relevant conditions, shedding light on the complex influence of water and on the potential to include waste nylon 6 cyclic dimer in the feedstock. The model and parameter estimates will be helpful in future models of nylon 6/6,6 copolymerization in continuous reactor systems.     

Tensile deformation of electrospun nylon‐6,6 nanofibers

Nylon‐6,6 nanofibers were electrospun at an elongation rate of the order of 1000 s^?1 and a cross‐sectional area reduction of the order of 0.33 × 10⁵. The influence of these process peculiarities on the intrinsic structure and mechanical properties of the electrospun nanofibers is studied in the present work. Individual electrospun nanofibers with an average diameter of 550 nm were collected at take‐up velocities of 5 and 20 m/s and subsequently tested to assess their overall stress–strain characteristics; the testing included an evaluation of Young's modulus and the nanofibers' mechanical strength. The results for the as‐spun nanofibers were compared to the stress–strain characteristics of the melt‐extruded microfibers, which underwent postprocessing. For the nanofibers that were collected at 5 m/s the average elongation‐at‐break was 66%, the mechanical strength was 110 MPa, and Young's modulus was 453 MPa, for take‐up velocity of 20 m/s—61%, 150 and 950 MPa, respectively. The nanofibers displayed α‐crystalline phase (with triclinic cell structure). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1482–1489, 2006     

Effect of needle diameter on nanofiber diameter and thermal properties of electrospun poly(methyl methacrylate)

The effect of needle diameter on the resulting electrospun poly(methyl methacrylate) (PMMA) average nanofiber diameter has been evaluated for three different needle gauges. The resulting nanofibers were observed and analyzed by scanning electron microscopy (SEM), suggesting a lack of correlation between the needle diameter used and the resulting average nanofiber diameter. Thermogravimetric analysis (TGA) indicated an increase in the thermal stability of PMMA nanofibers when compared to powdered PMMA, while differential scanning calorimetry (DSC) studies evidenced lower glass transition temperatures (Tg) for PMMA nanofibers in the first heating cycle. Copyright © 2007 John Wiley & Sons, Ltd.     

Thermal,physical and mechanical properties of hydrogenated dimer acid-based Nylon 636/Nylon 66 copolymers

Hydrogenated dimer acid-based Nylon 636/NyIon 66 copolymers were synthesized by in situ polymerization.The effects of Nylon 66 contents on the copolymers were characterized by intrinsic viscosity measurements,attenuated total reflection-Fourier transform infrared spectroscopy,X-ray diffraction,differential scanning calorimetry,tliermogravimetric analysis and mechanical tests.The results showed that incorporation of Nylon 66 into hydrogenated dimer acid-based Nylon had no significant effect on the glass transition or melting temperatures.However,the crystallization temperature,crystallinity degree and the maximum rate of decomposition temperature from derivative thermogravimetry measurements vary.Mechanical testing data revealed that with increasing Nylon 66 concentrations,the tensile strength of copolymers increased,while the elongation at break point and notched izod impact strength decreased.The physical and mechanical properties of HN-40,HN-50 and HN-60 are similar to those of the current PA11,PA1212,and PA1111 Nylon products.     

Fluorescent PMMA/MEH‐PPV electrospun nanofibers: Investigation of morphology,solvent, and surfactant effect

Electrospinning is a powerful technique to produce nanofibers of tunable diameter and morphology for medicine and biotechnological applications. By doping electrospun nanofibers with inorganic and organic compounds, new functionalities can be provided for technological applications. Herein, we report a study on the morphology and optical properties of electrospun nanofibers based on the conjugated polymer poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV) and poly(methylmethacrylate) (PMMA). Initially, we investigate the influence of the solvent, surfactant, and the polymer concentration on electrospinning of PMMA. After determining the best conditions, 0.1% MEH‐PPV was added to obtain fluorescent nanofibers. The optical characterizations display the successful impregnation of MEH‐PPV into the PMMA fibers without phase separation and the preservation of fluorescent property after fiber electrospinning. The obtained results show the ability of the electrospinning approach to obtain fluorescent PMMA/MEH‐PPV nanofibers with potential for optical devices applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1388–1394     

Polyaniline/poly(methyl methacrylate) coaxial fibers: The fabrication and effects of the solution properties on the morphology of electrospun core fibers

Electrically conductive polyaniline (PANi)/poly(methyl methacrylate) (PMMA) coaxial fibers were prepared through the chemical deposition of PANi onto preformed PMMA fibers via in situ polymerization. PMMA fibers were prepared as core materials via electrospinning. Spectral studies and scanning electron microscopy observations indicated the formation of PANi/PMMA coaxial fibers with a diameter of approximately 290 nm and a PANi layer thickness of approximately 30 nm. The conductivity of the PANi/PMMA coaxial fibers was significantly higher than that of electrospun fibers of PANi/poly(ethylene oxide) blends and blend cast films of the same PANi composition. To reproducibly generate uniform‐core polymer fibers, the organic solution properties that affected the morphology and diameter of the electrospun fibers were investigated. The polymer molecular weight, solution concentration, solvent dielectric constant, and addition of soluble organic salts were strongly correlated to the morphology of the electrospun fiber mat. In particular, the dielectric constants of the solvents substantially influenced both the fiber diameter and bead formation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3934–3942, 2004     

Electrospinning of nylon-6,6 solutions into nanofibers: Rheology and morphology relationships

The relationship between the rheological properties of nylon-6,6 solutions and the morphology of their electrospun nanofibers was established. The viscosity of nylon-6,6 in formic acid(90%) was measured in the concentration range of 5 wt%-25 wt% using a programmable viscometer. Electrospinning of nylon-6,6 solutions was carried out under controlled parameters. The chemical structure, morphology and thermal properties of the obtained nanofibers were investigated using Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and differential scanning calorimetry(DSC), respectively. Entanglement concentration(ce) was found to be 15 wt% and a power law relationship between specific viscosity and solution concentration was observed with exponents of 2.0 and 3.3 for semi-dilute unentangled(c ce) and semi-dilute entangled(c ce) regimes, respectively. The diameter and uniformity of the nanofibers were found to be dependent on the viscosity. Moreover, the average diameter of electrospun nanofibers was found to be dependent on zero shear rate viscosity and normalized concentration(c/ce) in a power law relationship with exponents of 0.298 and 0.816, respectively. For nylon-6,6 solutions, the entanglement concentration(ce = 15 wt%) provides the threshold viscosity required for the formation of a stable polymeric jet during electrospinning and producing uniform beadless fibers. For concentrations less than ce, beaded fibers with some irregularities are formed. DSC analysis showed an increase in crystallinity of all electrospun samples compared to original polymer. Furthermore, Based on FTIR spectroscopy, α phase is dominant in electrospun nanofibers and minor amount of β and γ phases is also available.     

Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Preparation of porous ultrafine polyacrylonitrile (PAN) fibers by electrospinning

A facile method for the preparation of porous ultrafine nanofibers was demonstrated. The PAN/NaHCO₃ composite nanofibers were electrospun, and then NaHCO₃ was removed by a selective dissolution and reaction with the solution of hydrochloric acid (10 wt%). The obtained PAN fibers showed highly porous surfaces after the extraction of NaHCO₃. The structure and properties of ultrafine PAN nanofibers were characterized by Fourier transform infrared (FT‐IR), X‐ray diffraction (XRD), and thermogravimetry (TG). The results indicated that NaHCO₃ could be introduced into the PAN solution and successfully electrospun. CO₂ is released and pores are formed on the fibers. The morphology image of the fibers was detected by scanning electron microscope (SEM) and showed that many pores aligned the nanofibers. Copyright © 2008 John Wiley & Sons, Ltd.     

Modeling Equilibrium Behavior of Nylon 6, Nylon 6,6 and Nylon 6/6,6 Copolymer

Nylon 6 and nylon 6,6 reaction equilibria depend in a complex way on water concentration and temperature. For example, data sets from six research groups reveal that the apparent equilibrium constant for polycondensation increases with water at low water concentrations, reaches a maximum, and then decreases as the water concentration rises further. In this article, semi‐empirical expressions are proposed to describe the experimentally observed equilibrium behavior for the five main reactions that occur during nylon 6 and nylon 6,6 polymerization. Nine side reactions involving amidine ends, cyclopentanone ends, and hydrated carboxyl ends are used to develop expressions that account for the influence of both water and temperature on these equilibrium constants. Excellent fit to the data, over the entire range of the available nylon 6 and nylon 6,6 literature data, suggests that the proposed equations will be helpful for modeling reaction equilibria for nylon 6/6,6 copolymerization.     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

Detection of Phthalate Esters in Environmental Water Samples-Comparison of Nylon6 Nanofibers Mat-based Solid Phase Extraction and Other Conventional Extraction Methods

In this article, a new method for simultaneous determination of six phthalate esters was developed by a combination of electrospun nylon6 nanofibers mat‐based solid phase extraction with high performance liquid chromatography‐ultraviolet detector (HPLC‐UV). The six phthalate esters were dimethyl phthalate (DMP), diethyl phthalate (DEP), butyl benzyl phthalate (BBP), di‐n‐butyl phthalate (DBP), di‐(2‐ethylhexyl) phthalate (DEHP) and dioctyl phthalate (DOP). Under optimized conditions, all target analytes in 50 mL environmental water samples could be completely extracted by 2.5 mg nylon6 nanofibers mat and eluted by 100 µL solvent. Compared with C18 cartridges solid phase extraction, C18 disks solid phase extraction and national standard method (China), nylon6 nanofibers mat‐based solid phase extraction was advantageous in aspects of simple and fast operation, low consumption of extraction materials and organic solvents. The four methods were applied to analysis of environment water samples. All the results indicated that the determination values of target compounds with the proposed method were consistent with C18 cartridges and C18 disks solid phase extraction method, and the new method was better than the national standard method in aspects of recovery, LOD and precision. Therefore, nylon6 nanofibers mat has great potential as a novel material for solid phase extraction.     

Preparation,characterization, and properties of nanofibers based on poly(vinylidene fluoride) and polyhedral oligomeric silsesquioxane

Nanostructered nanofibers based on poly(vinylidene fluoride) (PVDF) and polyhedral oligomeric silsesquioxane (POSS) have been prepared by electrospinning process. The starting solutions were prepared by dissolving both the system components in the mixture N,N‐dimethylacetamide/acetone. The characteristics of the fiber prepared, studied by scanning electron microscopy, atomic force microscopy, and wide angle X‐ray diffraction, have been compared with those of PVDF fibers. Morphological characterization has demonstrated the possibility to obtain defect‐free PVDF/POSS nanofibers by properly choosing the electrospinning conditions, such as voltage, polymer concentration, humidity, etc. Conversely, in the case of fibers based on the neat polymer, it was not possible to attain the complete elimination of beads in the electrospun nanofibers. The different behavior of the two types of solutions has been ascribed to silsesquioxane molecules, which, without influencing the solution viscosity or conductivity, favor the formation of uniform structures by decreasing the system surface tension. Concerning POSS distribution in the fibers, the morphological characterization of the electrospun films has shown a submicrometric dispersion of the silsesquioxane. It is relevant to underline that cast films, prepared by the same solutions, have been found to be characterized by POSS aggregation, thus demonstrating a scarce affinity between the two‐system components. Indeed, the peculiar solvent evaporation of the electrospun solution, which is much faster than that occurring during the cast process, prevents POSS aggregation, thus leading to the formation of nanofibers characterized by a silsesquioxane dispersion similar to that present in solution. Finally, the presence of POSS improves the electrospun film mechanical properties. Copyright © 2011 John Wiley & Sons, Ltd.     

Crystalline transition in Nylon 10 10

Variable‐temperature X‐ray diffraction was used to monitor the crystalline transition of Nylon 10 10. It could be found that the α‐phase of the sample transforms into a γ‐phase at about 135°C, if the sample is heated from room temperature to a high temperature, which is the so‐called Brill transition of Nylon 10 10. In addition, Nylon 10 10 was found to crystallize directly in a kind of α‐phase from the melt at high temperature, which is much different from the behavior of Nylon 66 and Nylon 10 12. Upon further cooling to room temperature, Nylon 10 10 preserved the α‐phase revealing two peaks in its XRD patterns. However, if the Nylon 10 10 sample with γ‐form was not melted, but immediately cooled from a temperature between T_B and T_m, the reverse transition from γ‐form to α‐form could be observed at about 130°C, indicating reversible Brill transition of Nylon 10 10.     

Influence of solvents properties on morphology of electrospun polyurethane nanofiber mats

Segmented polyurethane (SPU) nanofiber mats were prepared by electrospinning technique using the combination of four different solvents viz. tetrahydrofuran, N,N′‐dimethyl formamide, N,N′‐dimethyl acetamide, and dimethyl sulfoxide. Morphology of the electrospun nanofibers was examined by field emission scanning electron microscope. Experimental results revealed that the morphologies of polyurethane nanofiber mats have been changed significantly with the solvent selection for the electrospinning. It was observed that the diameters and morphology of the SPU nanofibers were influenced greatly by the use of combination of solvents. The uniform polyurethane nanofibers without beads or curls could be prepared by electrospinning through the selection of combination of good conductive and good volatile solvent viz. 7.5 wt/v% of SPU in N,N′‐dimethyl formamide/tetrahydrofuran (30 : 70 v/v) solutions at 20 kV applied voltages and volume flow rate of 1 ml/min. On the basis of the results obtained from this investigation, it has been established that solvent selection is one of the driving factors for controlling the morphology of the polyurethane electrospun nanofiber mats. The well‐controlled morphology of electrospun polyurethane nanofiber mats could be useful for many potential industrial applications such as in biomedical, smart textiles, nanofiltration, and sensors. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and characterization of polypyrrole nanofibers with different dopants

Nanostructures of polypyrrole (PPy) were synthesized in the presence of different dopants including hydrochloric acid (HCl), ferric chloride (FeCl₃), p‐toluene sulfonic acid (p‐TSA), camphor sulfonic acid (CSA), and polystyrene sulfonic acid (PSSA), using a simple interfacial oxidative polymerization method. The method is a reliable non‐template approach with relatively simple instrumentation, ease of synthesis, and economic viability for synthesizing PPy nanostructures. Morphology of synthesized PPy structures was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which indicate the formation of one‐dimensional (1D) nanofibers with average diameter of 75–180 nm. Energy dispersive spectrum (EDS) of the PPy nanofibers indicates the attachment of the dopants to the PPy backbone; the fact is further confirmed by the Fourier transform infrared (FTIR) spectra of PPy nanostructures. Thermal stabilities of the nanostructures explored using thermal gravimetric analysis (TGA) follow the order PPy‐p‐TSA > CSA > HCl > FeCl₃ > PSSA. It is noticed that the electrical conductivity (EC) of PPy nanostructures depends upon the nature of dopant (PPy‐p‐TSA > CSA > HCl > FeCl₃ > PSSA), PPy‐p‐TSA nanofibers showing the highest EC of 6 × 10^?2 Scm^?1. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of compatibilizer on morphology and properties of HDPE/Nylon 6 blends

The compatibilization effect of linear low‐density polyethylene‐grafted maleic anhydride (LLDPEgMA) and high‐density polyethylene‐grafted maleic anhydride (HDPEgMA) on high‐density polyethylene (HDPE)/polyamide 6 (Nylon 6) blend system is investigated. The morphology of 45 wt %/55 wt % polyethylene/Nylon 6 blends with three compatibilizer compositions (5 wt %, 10 wt %, and 15 wt %) are characterized by atomic force microscopic (AFM) phase imaging. The blend with 5 wt % LLDPEgMA demonstrates a Nylon 6 continuous, HDPE dispersed morphology. Increased amount of LLDPEgMA leads to sharp transition in morphology to HDPE continuous, Nylon 6 dispersed morphology. Whereas, increasing HDPEgMA concentration in the same blends results in gradual morphology transition from Nylon 6 continuous to co‐continuous morphology. The mechanical properties, oxygen permeability, and water vapor permeability are measured on the blends which confirm the morphology and indicate that HDPEgMA is a better compatibilizer than LLDPEgMA for the HDPE/Nylon 6 blend system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 281–290     

Preparation,Tg improvement,and thermal stability enhancement mechanism of soluble poly(methyl methacrylate) nanocomposites by incorporating octavinyl polyhedral oligomeric silsesquioxanes

The soluble poly(methyl methacrylate‐co‐octavinyl‐polyhedral oligomeric silsesquioxane) (PMMA–POSS) hybrid nanocomposites with improved T_g and high thermal stability were synthesized by common free radical polymerization and characterized using FTIR, high‐resolution ¹H NMR, ²⁹Si NMR, GPC, DSC, and TGA. The POSS contents in the nanocomposites were determined based on FTIR spectrum, revealing that it can be effectively adjusted by varying the feed ratio of POSS in the hybrid composites. On the basis of the ¹H NMR analysis, the number of the reacted vinyl groups on each POSS molecules was determined to be about 6–8. The DSC and TGA measurements indicated that the hybrid nanocomposites had higher T_g and better thermal properties than the pure PMMA homopolymer. The T_g increase mechanism was investigated using FTIR, displaying that the dipole–dipole interaction between PMMA and POSS also plays very important role to the T_g improvement besides the molecular motion hindrance from the hybrid structure. The thermal stability enhances with increase of POSS content, which is mainly attributed to the incorporation of nanoscale inorganic POSS uniformly dispersed at molecular level. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5308–5317, 2007     

Microstructural Study of Nylon-6/Gelatin Composite Nanofibers

Electrospinning is a simple and effective technology for fabricating nanofibers and polymer blending provides strength and minimal defects of electrospun ones. Therefore, in the present study, fabrication, and characterization of nylon-6/gelatin electrospun nanofibers using low-toxic solvents was investigated as means to improve the morphological deficiencies of gelatin nanofibers and facilitate its electrospinnability. The morphology of electrospun nylon-6/gelatin nanofibers were characterized using scanning electron microscope (SEM). SEM results showed that electrospun blend nanofibers had smooth surface with average diameter of from 40 to 100 nm; while, the miscibility of the blend and thermal behavior of nanofibers were determined using Fourier transform-infrared spectroscopy (FTIR) and differential scanning calorimeter (DSC). Water contact-angle measurement (WCA) was employed to investigating the wettability of nanofibers.     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.