Orthogonal wavelet analysis of counter gradient transport phenomena in turbulent asymmetric channel flow

In this paper four families of orthogonal wavelets are applied to analyze the turbulent counter gradient transport phenomena in fully developed asymmetric channel flows. The results show that: (1) In the instance of counter gradient transport, the principal scale of the coherent structure is responsible for the strong local counter gradient transport; (2) Counter gradient transport phenomena have a strong effect on the intermittency of turbulence; (3) Non-Gaussian part of the principal coherent structure is essential for counter gradient transport phenomena.The project supported by the National Natural Science Foundation of China (10272071, 10472063)     

湍流逆梯度输运的理论与实验研究

湍流中存在的动量、标量的逆梯度输运是当前湍流研究中一个十分重要的方向,它具有深刻的理论意义和重要的实用背景．本文从实验、理论两方面综述了湍流逆梯度输运的研究成果,并指出了一些值得今后进一步研究的方向．     

Aqueous Al2O3 nanofluids: the important factors impacting convective heat transfer

A high accuracy, counter flow double pipe heat exchanger system is designed for the measurement of convective heat transfer coefficients with different nanofluids. Both positive and negative enhancement of convective heat transfer of alumina nanofluids are found in the experiments. A modified equation was proposed to explain above phenomena through the physic properties of nanofluids such as thermal conductivity, special heat capacity and viscosity.     

Three-dimensional analysis of fluid flow and heat transfer in single- and two-layered micro-channel heat sinks

A three-dimensional numerical analysis of laminar fluid flow and conjugate heat transfer has been conducted for single- and two-layered micro-channel heat sinks. The validity of the numerical model has been confirmed by comparison with available experimental data. Results for the overall thermal resistance, pumping power, the maximum temperature difference on the heat-sink surface where the heat flux is applied, and an overall performance parameter were obtained for single- and two-layered sinks. The effects of Reynolds number, inlet velocity profile, and flow arrangement in the channels (parallel and counter) on these results are presented and discussed. A special emphasis was placed on the comparison between the thermal performances of the parallel and counter flow arrangements and further results were obtained in order to quantify and explain the relative performance under these flow arrangements.     

完全发展的非对称槽道湍流的分形维数研究

湍流的分形维数刻画了湍流的统计正则性 ,本文利用正交子波变换对完全发展的非对称槽道湍流脉动速度的实验数据进行了分析研究。文中首先将脉动速度信号分解到各个尺度 ,然后利用正则法和盒子法两种方法计算了不同尺度信号的分形维数 ,着重于考虑分形维数的变化趋势。研究结果表明 :(1 )随着信号分解尺度的增加 ,速度信号的低频部分和高频部分的维数都逐渐减小 ;(2 )逆输运现象对速度信号的分形维数没有本质的影响 ;(3)正则法计算得到的分形维数要略大于盒子法得到的分形维数     

Optimal control of unsteady compressible viscous flows

The control of complex, unsteady flows is a pacing technology for advances in fluid mechanics. Recently, optimal control theory has become popular as a means of predicting best case controls that can guide the design of practical flow control systems. However, most of the prior work in this area has focused on incompressible flow which precludes many of the important physical flow phenomena that must be controlled in practice including the coupling of fluid dynamics, acoustics, and heat transfer. This paper presents the formulation and numerical solution of a class of optimal boundary control problems governed by the unsteady two‐dimensional compressible Navier–Stokes equations. Fundamental issues including the choice of the control space and the associated regularization term in the objective function, as well as issues in the gradient computation via the adjoint equation method are discussed. Numerical results are presented for a model problem consisting of two counter‐rotating viscous vortices above an infinite wall which, due to the self‐induced velocity field, propagate downward and interact with the wall. The wall boundary control is the temporal and spatial distribution of wall‐normal velocity. Optimal controls for objective functions that target kinetic energy, heat transfer, and wall shear stress are presented along with the influence of control regularization for each case. Copyright © 2002 John Wiley & Sons, Ltd.     

A domain decomposition approach to compute wave breaking (wave‐breaking flows)

A heterogeneous domain decomposition approach is followed to simulate the unsteady wavy flow generated by a body moving beneath a free surface. Attention being focused on complex free surface configurations, including wave‐breaking phenomena, a two‐fluid viscous flow model is used in the free surface region to capture the air–water interface (via a level‐set technique), while a potential flow approximation is adopted to describe the flow far from the interface. Two coupling strategies are investigated, differing in the transmission conditions. Both the adopted approaches make use of the inviscid velocity field as boundary condition in the Navier–Stokes solution. For validation purposes, two different two‐dimensional non‐breaking flows are simulated. Domain decomposition results are compared with both fully viscous and fully inviscid results, obtained by solving the corresponding equations in the whole fluid domain, and with available experimental data. Finally, the unsteady evolution of a steep breaking wave is followed and some of the physical phenomena, experimentally observed, are reproduced. Copyright © 2003 John Wiley & Sons, Ltd.     

Large Scale Mixing for Immiscible Displacement in Heterogeneous Porous Media

We derive a large scale mixing parameter for a displacement process of one fluid by another immiscible one in a two-dimensional heterogeneous porous medium. The mixing of the displacing fluid saturation due to the heterogeneities of the permeabilities is captured by a dispersive flux term in the large scale homogeneous flow equation. By making use of the stochastic approach we develop a definition of the dispersion coefficient and apply a Eulerian perturbation theory to determine explicit results to second order in the fluctuations of the total velocity. We apply this method to a uniform flow configuration as well as to a radial one. The dispersion coefficient is found to depend on the mean total velocity and can therefore be time varying. The results are compared to numerical multi-realization calculations. We found that the use of single phase flow stochastics cannot capture all phenomena observed in the numerical simulations.     

湍流的相干结构:推演方法和结果

本文讨论壁面湍流发展的相干结构的观点.在简要的历史文献综述后,我们回顾一些基本观点, 并且介绍相干结构的思想.基于大量主要是由实验所得的结果,本文通过广泛运用的事件检 测技术,探讨湍流边界层内部和外部区域发生的现象.我们从边界层内部区域发生的现象、 边界层外部大尺度运动的发展和涡结构动力学的角度来描述流动的现象.在文章的 第2部分,介绍从背景流动中推演出湍流相干结构的各种方法以及在各种方法框架下所得到的结果, 讨论速度梯度张量不变量、压力的Hessian矩阵分析和本征正交分解等方法.每一个过程 都有``相干结构'的特定的定义,满足恰当的数学构架,并可以对湍流数据做相干结构动力 学分析.这一工作可能会对当前流体动力学家在湍流研究中用到的最新理论和技术的传播有 所贡献.     

Numerical modeling of viscoelastic counter flows using the pressure correction method

Counter flows of a viscoelastic fluid described by the rheological Oldroyd model in crossshaped channels are investigated. The modeling is based on the pressure correction method in a convenient-in-use form and with a simple topology of the computation grid and formally proved convergence. It is shown that, starting from certain threshold values of the Weissenberg numbers, the flow pattern in the stabilization stage exhibits considerable changes following two different mechanisms, depending on the Reynolds number. In particular, at low Reynolds numbers (less than 0.1) the flows involve vortex-like structures near the central point, where at the same time anomalies in normal stress distributions are observable. The similarity of these structures with the elastic instability phenomena, which were previously observed in the experimental realizations of the counter flows of this type and in other processes, is shown. To demonstrate the numerical procedure convergence, the results of calculations with different computation grid steps varied on a wide range are presented. In the context of the problem considered the general features of elastic instability are discussed.     

Control of a liquid–liquid heat exchanger

 The analytical solutions of equations describing the dynamics of distributed parameter systems are usually complicated in form and derivations and inconvenient to use for simulation and control system design. The liquid–liquid counter flow heat exchanger is an example of these disturbed parameter systems. An analytical solution of the dynamics of a symmetrically operated counter flow heat exchanger in the form of transfer function matrix is investigated in open-loop and close-loop conditions. The resulting non-linear model was linearized using perturbation approach. A feed-forward path controller to counteract at any disturbances in the boundary temperature and a non-interactive controller to decouple the outputs were implemented. Received on 22 February 2001 / Published online: 29 November 2001     

无黏流场中结构振动的气动非阻尼现象

研究跨音速飞行航天器的流-固耦合振动非阻尼现象的作用机理.研究表明,流场中的跨音速激波过程是此类非阻尼现象不可忽略的基本原因之一;由于流场对物体振动响应的滞后,形成了周期变化的分布气动力与物体运动之间有规律的相位差异,这种相位差可以引发局部的非阻尼的脉动力作用.这一机制与流场中的黏性过程如边界层和分离流动无关.单纯考虑黏性现象对非阻尼作用影响的认识是有缺陷的.     

Counter jet stagnation flows

The present paper concerns the stagnation flow produced by counter flowing air jets. Little experimental information exists on such flows in spite of their extensive employment in the theoretical treatment of diffusion flames. To remedy this situation, laser-Doppler measurements were performed to quantify the entire flow field. The experiments are described and the results of the velocity measurements presented. Differences between the investigated flow field and the ideal flow field, employed in theoretical studies, are pointed out.     

A probabilistic method for field solutions in two-phase flows

Solid-particle motion and related transport phenomena in two-phase flow are fluctuating processes in space and time. A deterministic method can describe only partially the intrinsic physics of these processes. In this paper, the fluctuations of the flow parameters are modelled by considering the spatial correlations, and a probabilistic computational method for two-phase flow is presented. The probabilistic governing equations have been discretized in space using a finite volume method, and then solved by applying the Neumann expansion method. This last method is time efficient, and its convergence can be guaranteed even for large fluctuations. A liquid-solid particle mixture flow in a circular pipe is taken as an example. Computational results illustrate the merit of the probabilistic approach for the prediction of two-phase flow phenomena.     

Application of particle image velocimetry to a transonic centrifugal compressor

As part of an ongoing research project the performance and internal flow field of a high-pressure ratio centrifugal compressor is being investigated. Based on previous, primarily, point-wise laser-optical measurements the compressor was redesigned and resulted in an improved impeller and diffuser with a single-stage pressure ratio of 6:1 at 50,000 rpm. Current research activities involve the use of particle image velocimetry (PIV) to analyze and further improve the understanding of the complex flow phenomena inside the vaned diffuser given the capability of PIV of capturing spatial structures. The study includes phase-resolved measurements of the flow inside a diffuser vane passage with respect to the impeller blade position. Both, instantaneous and phase-averaged velocity fields are presented. The flow field results obtained by PIV are to be used for future validation of the related CFD calculations, which in turn are expected to lead to further improvements in compressor performance. In addition, the potential of stereo PIV for this type of turbomachinery application could be successfully demonstrated.     

Two-phase flow phenomena along an adiabatic riser – An experimental study at the test-facility GENEVA

Long adiabatic riser geometries with low system pressures are present in a lot of energy and petrochemical processes. Natural-circulation systems are an appropriate solution to save operating and maintenance costs. Under certain circumstances natural-circulation systems tend to unstable mass flow, especially in the riser section. The pressure gradients can stress the construction materials and affect the heat transfer. This paper focuses on GENEVA test-facility and its natural-circulation circuit with heat input by steam condensation. The GENEVA test-facility is explained in detail with focus on the local void fraction measurement system in the adiabatic riser section. The differences to former natural circulation test-facilities are particular emphasized. Therefore a transient experiment is presented and analysed. Moreover the influence of flow restrictions at the downcomer outlet is explained and an experimental method is presented, to determine the maximum natural circulation mass flow of the natural-circulation circuit. Besides, a comparison between the two different riser inner diameters, which were used during the experiments, is presented. The convective heat transfer is analysed by taking into account different dimensionless numbers. A variety of experiments were performed up to 100 kW_el input power from the evaporators. Flashing and geysering as two types of occurred instabilities are stated and discussed in comparison to former test-facilities. Further phenomena like water hammer and counter current liquid flow are investigated. Based on these analyses constructive solutions can be derived, to stabilize the presented natural-circulation two-phase flow system.     

A control-volume based finite element method for three-dimensional incompressible turbulent fluid flow,heat transfer,and related phenomena

A control-volume based finite element method of equal-order type for three-dimensional incompressible turbulent fluid flow, heat transfer, and related phenomena is presented. The discretization equations are based mainly on the physics of the phenomena under consideration, more than on mathematical arguments. Special emphasis is devoted to the discretization of the convective terms and the continuity equation, and to the treatment of the boundary conditions imposed by the use of a high Reynolds k-?, type turbulence model. The pressure-velocity coupling in the fluid flow calculation is made from a derivative of the original SIMPLER method, without pressure correction. The discretized equations are solved in a sequential, rather than a coupled, form with significant advantage in the required computer time and storage. The method is an extension of a former version proposed by us for two-dimensional, laminar problems, and is here successfully applied to the following situations: three-dimensional deflected turbulent jet, and flows in 90° and 45° junctions of ducts with rectangular cross sections. The calculated results are in very good agreement with the experimental and numerical (obtained with the well established finite difference method) data available in the literature.     

Prediction of residual flow and thermoviscoelastic stresses in injection molding

A general model for predicting the total residual stresses generated during filling and cooling stages of injection-molded parts has been developed. The model takes into account the phenomena associated with non-isothermal stress relaxation. The main hypothesis in our approach is to use the kinematics of a generalized Newtonian fluid at the end of the filling stage as the initial state for the calculation of residual flow stresses. These stresses are calculated using a single integral rheological model (Wagner model). The calculation of stresses developed during the cooling stage is based on a thermoviscoelastic model with structural relaxation. Illustrative results emphasizing the effect of both the melt temperature and the flow rate during the filling stage are presented.     

Convective transport of nanoparticles in multi-layer fluid flow

Technologically, multi-layer fluid models are important in understanding fluid-fluid or fluid-nanoparticle interactions and their effects on flow and heat transfer characteristics. However, to the best of the authors’ knowledge, little attention has been paid to the study of three-layer fluid models with nanofluids. Therefore, a three-layer fluid flow model with nanofluids is formulated in this paper. The governing coupled nonlinear differential equations of the problem are non-dimensionalized by using appropriate fundamental quantities. The resulting multi-point boundary value problem is solved numerically by quasi-linearization and Richardson’s extrapolation with modified boundary conditions. The effects of the model parameters on the flow and heat transfer are obtained and analyzed. The results show that an increase in the nanoparticle concentration in the base fluid can modify the fluid-velocity at the interface of the two fluids and reduce the shear not only at the surface of the clear fluid but also at the interface between them. That is, nanofluids play a vital role in modifying the flow phenomena. Therefore, one can use nanofluids to obtain the desired qualities for the multi-fluid flow and heat transfer characteristics.     

差异流动变形破坏研究

工程岩体出现许多流变现象, 它最突出的特点是差异流动变形破坏。本文从流变现象及变形量测结果论述差异流动变形破坏特征, 并且根据蠕变流动变形破坏与时间的关系进行了差异流动变形分类, 这些类型同时存在于一个岩体或岩块内。