GABAA受体蛋白片段在大肠杆菌细胞表达条件研究*

为了提高GABAA受体a1蛋白片段在大肠杆菌中表达量,研究了重组菌的发酵条件,包括培养基、接种量、温度、摇床转速、pH、诱导培养时间和诱导剂IPTG使用浓度等对GABAA受体蛋白片段表达的影响。结果表明重组菌以LB培养基为发酵基质,按3％接种量,37℃培养细胞3.5h后IPTG 32℃诱导5h,菌体生物量为3.25g/L,目标蛋白表达量达95mg/L。用16L发酵罐进行放大培养,菌体生物量达4.95g/L,发酵周期5.5h,最高目标蛋白表达量达到136mg/L.     

HCMV pp65截短蛋白原核表达条件优化

为了提高HCMVpp65蛋白片段在大肠杆菌中表达量,研究了不同发酵条件对其表达的影响,包括培养基、接种量、温度、摇床转速、pH、诱导时间以及诱导剂IPTG使用浓度等。结果表明,以LB培养基为发酵液,按5%接种量,37℃培养3h后IPTG诱导5h,重组菌菌体生物量为0.6g/L,目的蛋白表达量达18mg/L。用3.7L发酵罐进行放大培养,菌体生物量达0.85g/L,最高目的蛋白表达量达到25mg/L。     

GABAA受体蛋白片段在大肠杆菌细胞表达条件研究

为了提高GABAA受体α1蛋白片段在大肠杆菌中表达量,研究了重组菌的发酵条件,包括培养基,接种量,温度,摇床转速,pH,诱导培养时间和诱导剂IPTG使用浓度等对GABAA受体蛋白片段表达的影响。结果表明重组菌以LB培养基为发酵基质,按3%接种量,37℃培养细胞3.5h后IPTG32℃诱导5h,菌体生物量为3.25g/L,目标蛋白表达量达95mg/L。用16L发酵罐进行放大培养,菌体生物量达4.95g/L,发酵周期5.5h。最高目标蛋白表达量达到136mg/L。     

多表位恶性疟疾疫苗M.RCAg-1在大肠杆菌表达的条件优化和大规模培养

通过以培养基配方、IPTG浓度、金属离子复合液浓度、镁离子浓度、表达时间、接种量、诱导时间点等发酵的重要条件对重组蛋白表达量影响的研究,确定多表位恶性疟疾疫苗M.RCAg-1蛋白最佳表达条件为以改良TB培养基培养、最优Mg2+,诱导剂IPTG和金属离子复合液浓度分别为10mmol/L,0.5mmol/L,6μl/ml,接种量为10%,表达时间为4.5h,将优化后的参数用于50L发酵罐进行连续3批中试规模的发酵,最终收获菌体湿重平均为31.8±1.78g/L,目的蛋白表达量可占菌体总蛋白的50%左右,试验确定了恶性疟疾多表位随机组合蛋白M.RCAg-1在大肠杆菌中的最优表达条件,该条件能够适合大规模培养需要。     

弧菌外膜蛋白ompk工程菌规模化培养表达初探

目的:为Ompk亚单位疫苗生产提供参数。方法:利用振荡和发酵培养,测定不同培养时间的菌液浊度和蛋白诱导表达效果。结果:工程菌30℃摇瓶培养10h,种子罐培养8～10h,较为合适;摇瓶和5L发酵罐诱导表达培养,升温42℃诱导表达,7h效果较佳;经5批次50L、500L发酵罐诱导表达培养,均可得到重组蛋白表达的工程菌体,50L和500L发酵罐最高生物量分别为5.32g/L和6.38g/L,平均可达到3.75 g/L和4.74 g/L;适当延迟升温诱导前的培养时间,可提高工程菌的得率。结论:初步确定了重组蛋白工程菌规模化诱导表达培养方法,利用500L发酵罐培养可得到诱导表达的工程菌体。     

GST-SUMO-MT融合蛋白在大肠杆菌中的自诱导表达

旨在考察在大肠杆菌中自诱导表达GST-SUMO-MT融合蛋白的可行性,并对自诱导培养条件及培养基成分进行优化,以提高蛋白产量。采用摇瓶培养,利用单因素和正交实验对工程菌自诱导的培养条件(诱导时间、诱导温度)和培养基组分(蛋白胨、酵母粉、甘油、葡萄糖、乳糖)进行优化,检测菌体浓度、可溶性目的蛋白的表达量。结果表明,自诱导培养基碳氮源的最优配比为:2%蛋白胨、2%酵母粉、0.3%甘油、0.05%葡萄糖和0.3%乳糖。重组菌自诱导表达最优发酵条件为:采用两阶段温度控制,37℃培养3 h,25℃继续培养13 h。此时可溶性目的蛋白的表达量和菌体浓度分别为LB培养基(IPTG诱导)的2.2倍和2.3倍。     

重组戊型肝炎病毒衣壳蛋白工程菌的高密度培养

在10L发酵罐中对戊型肝炎病毒衣壳蛋白在重组大肠杆菌中表达发酵工艺进行了研究,用分批培养方法探讨了不同培养基、培养基中磷酸盐浓度和Mg^2＋浓度等因素对菌体生长与重组蛋白表达的影响;用分批补料培养研究了不同的补料工艺对菌体生长与重组蛋白表达的影响,同时对重组菌诱导时期、诱导持续时间以及不同诱导温度表达包含体在尿素溶液中的溶解性进行了研究。结果表明,在优化后的培养基中,磷酸盐浓度、Mg^2＋浓度分别为80mmol/L 与20mmol/L时菌体生长与表达效果较好;分批补料培养中,37℃培养9h菌体达到对数期中期(约45OD600)为适宜诱导时期,加入终浓度为10mmol/L IPTG后诱导5h,OD600达到80以上,重组蛋白表达量达到29.74％,为最适收获菌体时间;37℃表达的包含体80％以上溶解在4mol/L的尿素溶液中,最终浓度达到14mg/mL; 10L发酵罐中确定的发酵工艺参数在30L发酵罐中进行了放大培养,10L发酵罐中确定的发酵工艺参数在30L发酵罐上具有可放大性与重复性, 可以应用于工业生产。     

重组人干扰素βser17工程菌发酵培养条件的优化研究

实验对重组人干扰素βser17(rhIFNβser17)工程菌的发酵培养条件进行了研究,通过实验优化确定了适宜rhIFNβser17表达的培养基、诱导剂使用浓度、诱导时期和诱导后的收获时间等,建立了发酵培养工艺,并在50L发酵罐进行了中试发酵,菌体收获量湿重达13.08g/L,rhIFNβser17表达量占菌体总蛋白的20.2%,纯化后比活性达2×107IU/mg蛋白以上,为进一步的下游开发奠定了基础。     

毕赤嗜甲醇酵母工程菌高密度培养表达黑曲霉菊粉内切酶的研究

目的:对毕赤嗜甲醇酵母工程菌inu-26高密度培养表达黑曲霉菊粉内切酶的条件进行优化,找出最佳的外源蛋白表达条件。方法:在摇瓶优化培养的基础上进行发酵罐高密度培养,优化最佳产酶条件。结果:以葡萄糖为碳源、微量元素添加量100～200mL/L、甲醇浓度1g/L、pH6.0～7.0、诱导时间96h时酶的表达量最高;摇瓶模拟高密度培养表明影响酵母生长的最主要因素葡萄糖和硫酸铵的最佳浓度分别为20～45和11.5g/L;利用培养基F1进行高密度培养优于其他培养基,工程菌生长符合指数生长曲线,细胞生长延迟期为1.36h,比生长速率μ为0.4846h-1。结论:以葡萄糖为碳源,采用葡萄糖-甲醇混合诱导和100%甲醇单一诱导相结合,在菌体鲜重约为280g/L时连续诱导96h,菌体生长良好,不会出现自溶,且酶的表达量最高,为摇瓶培养的3倍多,酶活最高可达540 U/mL。     

大肠杆菌发酵生产重组人源抗-HBs Fab

在KLF2000发酵罐中利用补料分批培养技术培养表达含重组质粒pBAD/HBs Fab的TOP10大肠杆菌,生产人源抗-HBs Fab,为批量生产作准备,在发酵过程中,控制溶氧30%以上,温度37℃,在基础培养基内生长4h后,补加以甘油为碳源的补料,继续生长到9h,加入阿拉伯糖,至终浓度为0.02%,30℃诱导表达5h,收集菌体,纯化制备目的蛋白。利用Western blot方法检测Fab抗原性,Dot blot方法检测生物学活性。14h发酵结束后,菌体密度最终达96g/L,纯化所得蛋白大约占菌体总蛋白的6%,含量为80mg/L,以重组质粒pBAD/HBs Fab,大肠杆菌TOP10表达表达比率与摇瓶相比没有降低,表达量达80mg/L左右,为大批量生产作了准备。     

Recent advances in the study of Kaposi's sarcoma-associated herpesvirus replication and pathogenesis

It has now been over twenty years since a novel herpesviral genome was identified in Kaposi's sarcoma biopsies. Since then, the cumulative research effort by molecular biologists, virologists, clinicians, and epidemiologists alike has led to the extensive characterization of this tumor virus, Kaposi's sarcoma-associated herpesvirus(KSHV; also known as human herpesvirus 8(HHV-8)), and its associated diseases. Here we review the current knowledge of KSHV biology and pathogenesis, with a particular emphasis on new and exciting advances in the field of epigenetics. We also discuss the development and practicality of various cell culture and animal model systems to study KSHV replication and pathogenesis.     

The structure, reproduction and taxonomy of Vidalia and Osmundaria (Rhodophyta, Rhodomelaceae)

Comprises species occurring mostly in subtidal habitats in tropical, subtropical and warm-temperate areas of the world. An analysis of the type species, V. spiralis (Sonder) Lamouroux ex J. Agardh, a species from Australia, establishes basic characters for distinguishing species in the genus. These characters are (1) branching patterns of thalli, (2) flat blades that may be spiralled on their axis, (3) width of the blade, (4) primary or secondary derivation of sterile and fertile branchlets and (5) position of sterile and fertile branchlets on the thalli. Application of the latter two characters provides an important basic method for separation of species into three major groups. Osmundaria , a genus known only in southern Australia, was studied in relation to Vidalia , and its separation from the Vidalia assemblage is not accepted. Species of Vidalia therefore are transferred to the older genus name, Osmundaria. Two new species, Osmundaria papenfussii and Osmundaria oliveae are described from Natal. Confusion in the usage of the epithet, Vidalia fimbriala Brown ex Turner has been clarified, and Vidalia gregaria Falkenberg, described as an epiphyte on Osmundaria pro/ifera Lamouroux, is revealed to be young branches of the host, Osmundaria prolifera.     

New or rare chromosome counts in Artemisia L. (Asteraceae, Anthemideae) and related genera from Kazakhstan

Fifteen chromosome counts of six Artemisia taxa and one species of each of the genera Brachanthemum, Hippolytia, Kaschgaria, Lepidolopsis and Turaniphytum are reported from Kazakhstan. Three of them are new reports, two are not consistent with previous counts and the remainder are confirmations of very scarce (one to four) earlier records. All the populations studied have the same basic chromosome number, x = 9, with ploidy levels ranging from 2x to 6x. Some correlations between ploidy level, morphological characters and distribution are noted.     

肝癌中HBV和HCV基因和抗原的分布及意义

采用原位分子杂交方法检测HCV RNA及HBV X基因;采用免疫组织化学方法研究HCV核心抗原,非结构区C33c抗原及HBxAg在肝细胞肝癌中的定位及分布.结果表明(1)HCV RNA、HBV X基因在肝细胞肝癌组织检出率分别为40%(55/136)和82%(112/136).HCV RNA定位于癌细胞的胞浆内,阳性细胞呈散在、灶状及弥漫分布三种形式;HBV X基因在肝癌细胞中的分布呈胞浆型、核型及核浆型,阳性细胞也呈上述三种分布形式;(2)HCV C33c抗原、核心抗原在肝细胞肝癌中的阳性率为81%(133/164)及86%(141/164).C33c抗原定位于癌细胞及肝细胞的胞浆内;核心抗原既定位于癌细胞核中,又可定位于胞浆中.C33c抗原阳性细胞以灶状分布为主;而核心抗原阳性细     

Selection with two alleles and complete dominance

For a plant selection model with frequency-independent viabilities, fertilities and selfing rates, it is shown that apart from global fixation, for certain parameter combinations a protected polymorphism and facultative fixation (either allele may become fixed according to initial frequencies) may both occur. Facultative fixation requires different selling rates for the dominant and recessive type. Protection of the polymorphism requires resource allocation for male and female function. In this connection the problem of purely genetically caused population extinction is discussed.
For general frequency dependence and regular segregation, the chances for establishment of a completely recessive gene are compared to those of a completely dominant gene. It is proven that the process of establishment of the recessive gene, despite a fitness advantage, may be considerably endangered by drift effects if random mating prevails. The recessive gene may reach the same effectivity in establishment as a dominant gene, only if the recessive homozygote mates exclusively with its own type during the period of establishment.