薄矩形柱绕流旋涡脱落的抑制

用窄条形控制件对截面宽度为B、厚度为H的矩形柱体绕流的旋涡脱落进行抑制.实验在风洞中进行, 实验范围为B/H=2.0~5.0,Re=V_∞H/\nu=3.75× 103~1.05×104. 矩形柱的宽边B与来流平行, 窄条与柱体等长, 且两者轴线相互平行放置. 窄条宽度为b/H=0.5, 窄条厚度远小于其宽度; 窄条位置可变, 但窄条表面保持与来流垂直. 尾流脉动速度测量和流动显示结果表明: 当窄条位于一个有效区内时, 矩形柱体两侧的旋涡脱落被抑制; 而当窄条位于一个单侧有效区内时, 矩形体一侧的旋涡脱落被抑制, 在另一侧旋涡脱落却仍存在. 有效区范围从矩形体的上游某点一直延续到矩形体的下游某点. 单侧有效区将整个有效区围在其中. 有效区和单侧有效区范围随着B/H的增大而增大, 但随着Re的增大而减小.      

较高Re数圆柱尾流的控制

引入一个窄条作为控制件，在Re=3.0×10 3~2.0×10 4范围内对圆柱尾流进行控制实验。窄条长度与柱体长度相同,厚 度为柱体直径的 0.015~0.025倍,宽度为柱体直径的0.18倍. 窄条的两个长边 与柱中心轴平行, 而且三者共面. 控制参数为窄条位置, 可由间距(窄条到柱轴)比λ/(0.5D)和风向角β (窄 条面与来流的夹角)确定. 采用流动显示和热线测量方法,对控制和未控制尾流的流动状态, 平均速度分布和脉动速度情况,以及作用于柱体和控制件的总阻力进行了研究和比较. 研究结果证明, 当窄条位于柱体尾流中一定区域内时, 可有效抑制柱体两侧的旋涡脱落.有效控制后的尾流湍流度也相应减小. 在不同Re数下,找出了有效抑制旋涡脱落的窄条位置区域, 并用动量积分估计了作用于柱体和窄条上的总阻力与光圆柱阻力的比值及其随风向角的变 化. 对λ/(0.5D)=2.9情况,得到了减阻的风向角区域(β=0°~40°与180°附近)以及最大减阻率32%.以上事实表明，在近尾流局部区域施加小的干扰,可改变较高Re数圆柱尾流的整体性质.     

单窄条控制件对横向振荡柱体尾流 2P模式 旋涡脱落的改变

横向强迫振荡柱体尾流控制是柱体涡激振动控制的基础,在海洋、土木等工程中具有重要意义. 横向强迫振荡柱体尾流中存在一种锁频旋涡脱落模式,即在一个振荡周期内柱体上、下侧各脱落旋转方向相反的一对涡,称为2P模式. 本文将相对宽度b/D=0.32的窄条控制件置于横向强迫振荡柱体下游,对振幅比A/D=1.25, 无量纲振频f_e D/V_∞=0.22,雷诺数Re=1 200的2P模式旋涡脱落进行干扰,并通过改变控制件位置,研究旋涡的变化规律. 采用二维大涡模拟和实验验证方法进行研究,在控制件位置范围0.8≤X/D≤3.2, 0.4≤Y/D≤3.2内,得到了2P, 2S, P+S和另外6种新发现的旋涡脱落模式,并对各模式旋涡的形成过程作了详细描述. 在控制件位置平面上给出了各旋涡模式的存在区域,画出了旋涡脱落强度的等值线图,并发现在一个相当大的区域内,旋涡脱落强 度可减小一半以上,尾流变窄. 发现柱体大幅振荡引起的横向剪切流在旋涡生成中起关键作用. 探讨了控制件对横向剪切流的影响,分析了控制件在每种旋涡模式形成中的作用机制.      

单窄条控制件对横向振荡柱体尾流2P模式旋涡脱落的改变

横向强迫振荡柱体尾流控制是柱体涡激振动控制的基础,在海洋、土木等工程中具有重要意义.横向强迫振荡柱体尾流中存在一种锁频旋涡脱落模式,即在一个振荡周期内柱体上、下侧各脱落旋转方向相反的一对涡,称为2P模式.本文将相对宽度b/D=0.32的窄条控制件置于横向强迫振荡柱体下游,对振幅比A/D=1.25,无量纲振频f_eD/V_∞=0.22,雷诺数Re=1 200的2P模式旋涡脱落进行干扰,并通过改变控制件位置,研究旋涡的变化规律.采用二维大涡模拟和实验验证方法进行研究,在控制件位置范围0.8 X/D 3.2,0.4 Y/D 3.2内,得到了2P,2S,P+S和另外6种新发现的旋涡脱落模式,并对各模式旋涡的形成过程作了详细描述.在控制件位置平面上给出了各旋涡模式的存在区域,画出了旋涡脱落强度的等值线图,并发现在一个相当大的区域内,旋涡脱落强度可减小一半以上,尾流变窄.发现柱体大幅振荡引起的横向剪切流在旋涡生成中起关键作用.探讨了控制件对横向剪切流的影响,分析了控制件在每种旋涡模式形成中的作用机制.     

流向振荡柱体尾流控制研究进展

详细介绍了近几年采用尾部喷射、隔离板和小窄条控制件等3 种方法对流向振荡柱体绕流旋涡脱落的抑制情况. 在研究范围内存在非锁频和3种锁频旋涡脱落模式. 风洞实验表明, 尾部喷射对这4 种模式都有抑制效果,窄条控制件对非锁频和2种锁频模式具有抑制效果, 而隔离板仅对非锁频和1 种锁频模式有效. 在不同流动和振荡条件下找出了每种方法的有效控制区, 研究了减阻和减少脉动力的效果, 并探讨了控制机理.      

流向振荡柱体尾流控制研究进展

正详细介绍了近几年采用尾部喷射、隔离板和小窄条控制件等3种方法对流向振荡柱体绕流旋涡脱落的抑制情况.在研究范围内存在非锁频和3种锁频旋涡脱落模式.风洞实验表明,尾部喷射对这4种模式都有抑制效果,窄条控制件对非锁频和2种锁频模式具有抑制效果,而隔离板仅对非锁频和1种锁频模式有效.在不同流动和振荡条件下找出了每种方法的有效控制区,研究了减阻和减少脉动力的效     

旋转振荡板尾流的控制研究

桥跨结构发生颤振时的旋涡尾流可由二维强迫旋转振荡板绕流模拟. 在弦厚比B/H = 5的振荡板两侧对称地放置两个宽度比均为b/H = 0.33的窄条, 对尾流的锁频旋涡脱落进行控制. 采用数值模拟和实验验证方法, 对旋涡场、尾流平均和脉动速度, 以及板所受扭转力矩和升力进行研究, 研究的振幅范围β = 0° ~ 10°, 振频范围f_eH/V_∞ = 0 ~ 0.0857, 雷诺数Re = V_∞H/V = 2800. 窄条位置分为板的前缘、中央和尾缘3种, 控制参数为窄条横向坐标y/H. 根据实验结果, 当窄条位置y/H在一定范围, 振幅β = 0° ~ 7.5°, 振频f_eH/V_∞ = 0 ~ 0.08时, 有控制和无控制尾流脉动速度功率谱主峰的比值远低于1, 最低可达0.3左右. 根据数值模拟结果, 当中央控制件位于y/H = ±1附近时, 在振幅β = 0° ~ 7.5°, 和一定频率范围内, 脉动扭转力矩均方根和升力均方根都有大幅下降, 最多可分别降低43%和80%. 引入第一和第二涡黏系数, 将尾流无规则脉动形成的湍流法向和切向应力, 分别与扰动速度幅值的法向和切向梯度相联系, 得到线性稳定性方程. 稳定性分析表明, 施加控制后, 最大扰动放大因子ω_{i max}大幅降低, 扰动增长的频率范围显著收窄. 窄条改变尾流速度剖面形状并增大湍流涡黏系数, 从而减弱尾流的不稳定性.      

虚拟边界法研究正交双圆柱及串列双圆球绕流

把Goldstein等人提出的虚拟边界法推广到三维情况,研究了 Re=150时不同间距下正交双圆柱绕流,和Re=250时不同间距下串列双 圆球绕流流场. 对于正交双圆柱绕流,当间距比大于3,下游圆柱对上游圆柱尾流的影响只 限定在下游圆柱的尾流所扫过的范围之内;当间距比小于等于3,下游圆柱对上游圆柱尾流 的影响扩大,下游圆柱尾流扫过区上下出现两排三维流向二次涡结构. 对于串列圆球绕流, 研究发现,在小间距比(L/D≈ 1.5)的情况下,由于上下游圆球尾流区的相互抑 制消除了压力不稳定性,整个流场呈现稳 态轴对称特征;间距比为2.0时,周向压力梯度诱发出流体的周向输运,流场呈现稳态非对 称性,但流场中存在特定的对称面;间距比增大到2.5后,绕流场开始周期振荡,原有的对 称面依旧存在;在间距比3.5时下游圆球下表面的涡结构强度有所减弱,导致占优频率发生 交替;间距比增至7.0时,整个流场恢复稳态特征,两圆球尾部同时出现双线涡,这时流场 对称面的位置发生了变动.     

中等雷诺数圆柱尾流旋涡脱落的控制

介绍通过实验对圆柱尾流旋涡脱落进行抑制的方法及其结果.实验模型的展径比为38,实验的雷诺数范围为3×102～1.6×103.抑制方法是在圆柱（直径为D）表面沿展向每隔一定间距伸出一直径0.18D、长度为1.5D的小棒.实验结果表明,当棒间距小于3D,棒与来流夹角在30°～90°范围内,可有效抑制旋涡脱落.     

风嘴对旋转振荡板旋涡脱落的控制

5∶1矩形柱体被认为是通用桥面几何形状的代表,其简化模型可以用来进行风振控制的研究。风嘴作为一种常用的流动控制装置,能起到减阻和增加矩形板气动稳定性的效果,但控制装置对强迫振荡柱体的控制机理仍缺乏研究。研究者通过对节段模型施加强迫振动,在实验模型前部施加边缘型对称型风嘴,研究控制装置对矩形板尾流旋涡脱落的影响。通过流动显示结果,总结了施加风嘴后的四种旋涡脱落模式。并通过快速傅里叶变化频域分析法,得到实验模型后缘X/D=10处的速度功率谱。施加风嘴控制能增大旋涡脱落频率,并抑制尾流旋涡脱落的能量。而数值模拟得到的不同实验工况下的升力均方根和力矩均方根显著减小,最大降幅分别为52%和23%,表明矩形板气动稳定性的提升和尾流不稳定性的减弱。     

The effect of a wake-mounted splitter plate on the flow around a surface-mounted finite-height circular cylinder

The influence of a wake-mounted splitter plate on the flow around a surface-mounted circular cylinder of finite height was investigated experimentally using a low-speed wind tunnel. The experiments were conducted at a Reynolds number of Re=7.4×10⁴ for cylinder aspect ratios of AR=9, 7, 5 and 3. The thickness of the boundary layer on the ground plane relative to the cylinder diameter was δ/D=1.5. The splitter plates were mounted on the wake centreline with negligible gap between the base of the cylinder and the leading edge of the plate. The lengths of the splitter plates, relative to the cylinder diameter, ranged from L/D=1 to 7, and the plate height was always equal to the cylinder height. Measurements of the mean drag force coefficient were obtained with a force balance, and measurements of the vortex shedding frequency were obtained with a single-component hot-wire probe situated in the wake of the cylinder–plate combination. Compared to the well-studied case involving an infinite circular cylinder, the splitter plate was found to be a less effective drag-reduction device for finite circular cylinders. Significant reduction in the mean drag coefficient was realized only for the finite circular cylinder of AR=9 with intermediate-length splitter plates of L/D=1–3. The mean drag coefficients of the other cylinders were almost unchanged. In terms of its effect on vortex shedding, a splitter plate of sufficient length was able to suppress Kármán vortex shedding for all of the finite circular cylinders tested. For AR=9, vortex shedding suppression occurred for L/D≥5, which is similar to the case of the infinite circular cylinder. For the smaller-aspect-ratio cylinders, however, the splitter plate was more effective than what occurs for the infinite circular cylinder: for AR=3, vortex shedding suppression occurred for all of the splitter plates tested (L/D≥1); for AR=5 and 7, vortex shedding suppression occurred for L/D≥1.5.     

外部激励Stuart-Landau模型的数值研究

将非线性常微分方程组周期解的求解看作一个边值问题 ,运用Newton迭代构造求解这组方程的数值方法。利用上述方法求得了激励Stuart Landau方程的周期解 ,研究了圆柱振动对圆柱后Karman涡街的抑制现象 ,和振动的频率锁定现象 ,证明了激励Stuart Landau方程描写钝体尾迹动力系统的有效性     

Hydrodynamics of flow over a transversely oscillating circular cylinder beneath a free surface

In this paper, hydrodynamic force coefficients and wake vortex structures of uniform flow over a transversely oscillating circular cylinder beneath a free surface were numerically investigated by an adaptive Cartesian cut-cell/level-set method. At a fixed Reynolds number, 100, a series of simulations covering three Froude numbers, two submergence depths, and three oscillation amplitudes were performed over a wide range of oscillation frequency. Results show that, for a deeply submerged cylinder with sufficiently large oscillation amplitudes, both the lift amplitude jump and the lift phase sharp drop exist, not accompanied by significant changes of vortex shedding timing. The near-cylinder vortex structure changes when the lift amplitude jump occurs. For a cylinder oscillating beneath a free surface, larger oscillation amplitude or submergence depth causes higher time-averaged drag for frequency ratio (=oscillation frequency/natural vortex shedding frequency) greater than 1.25. All near-free-surface cases exhibit negative time-averaged lift the magnitude of which increases with decreasing submergence depth. In contrast to a deeply submerged cylinder, occurrences of beating in the temporal variation of lift are fewer for a cylinder oscillating beneath a free surface, especially for small submergence depth. For the highest Froude number investigated, the lift frequency is locked to the cylinder oscillation frequency for frequency ratios higher than one. The vortex shedding mode tends to be double-row for deep and single-row for shallow submergence. Proximity to the free surface would change or destroy the near-cylinder vortex structure characteristic of deep-submergence cases. The lift amplitude jump is smoother for smaller submergence depth. Similar to deep-submergence cases, the vortex shedding frequency is not necessarily the same as the primary-mode frequency of the lift coefficient. The frequency of the induced free surface wave is exactly the cylinder oscillation frequency. The trends of wave length variation with the Froude number and frequency ratio agree with those predicted by the linear theory of small-amplitude free surface waves.     

Resonance in flow past oscillating cylinder under subcritical conditions

Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes and hydrodynamics forces on the cylinder surface are systematically investigated. Special attention is paid to the phenomenon of resonance induced by the cylinder oscillation. The results demonstrate that vortex shedding can be excited extensively under subcritical conditions, and the response region of vibration frequency broadens with increasing Reynolds number and oscillation amplitude. Two distinct types of vortex shedding regimes are observed. The first type of vortex shedding regime(VSR I) is excited at low frequencies close to the intrinsic frequency of flow, and the second type of vortex shedding regime(VSR II)occurs at high frequencies with the Reynolds number close to the critical value. In the VSR I, a pair of alternately rotating vortices are shed in the wake per oscillation cycle,and lock-in/synchronization occurs, while in the VSR II, two alternately rotating vortices are shed for several oscillation cycles, and the vortex shedding frequency is close to that of a stationary cylinder under the critical condition. The excitation mechanisms of the two types of vortex shedding modes are analyzed separately.     

Suppression of Low-frequency Variations in Vortex Shedding by a Splitter Plate Behind a Bluff Body

Measurements of instantaneous pressure fluctuations on a trapezoidal cross-section cylinder indicate that the low-frequency variations embedded in the vortex-shedding process can be successfully suppressed by insertion of a splitter plate whose length is twice the maximum width of the trapezoidal cylinder. The experiments were performed at Reynolds numbers in a range of 5 × 10³ to 4·5 × 10⁴. Spanwise correlation of the pressure fluctuations measured on the cylinder further indicates that the suppression of low-frequency variations improves the degree of two-dimensionality of vortex shedding. These findings are attributed to the presence of the splitter plate having an effect on stabilizing the vortex formation length which is comparable to the length of the splitter plate, thus eliminating the low-frequency variations embedded in the base pressure.     

流向振荡圆柱绕流的格子Boltzmann方法模拟

用一种新近发展起来的格子Boltzmann方法(LBM)在相对较小的雷诺数(Re \le 200)条件下模拟了不可压缩的流向振荡圆柱绕流问题, 考查了涡脱落模态和升阻力特性. 通过模拟, 在近尾流区发现了实验研究中已经发现的对称/反对称的涡脱落模态, 包括有些传统数值方法未发现的模态. 研究了频率锁定区域的范围及其与振幅的关系, 发现振幅越大, 发生锁定的频率区域越宽. 此外还对升阻力进行了定量意义的模拟,研究了振荡频率和振幅与升阻力的关系.