Effect of High-Pressure Coolant Supplies when Machining Nickel-Base,Inconel 718, Alloy with Ceramic Tools

Chip breakability is significantly improved with the use of high pressure coolant supply. This is a result of the reduction in the tool-chip contact length during machining as the coolant under high pressure lifts the chip up after passing the deformation zone. Increasing the coolant pressure results in shorter ceramic tool life when machining Inconel 718 suggesting that the high pressure coolant supply reduces temperature at the cutting zone below a critical level where ceramic tools can perform satisfactorily. The inadequate fracture toughness of ceramic tools makes them more susceptible to failure by mechanical action such as notching at the depth of cut line and premature fracture. The notch wear rate increases with higher coolant supply pressure due to significant erosion of the tool material by the high pressure coolant jet. This mechanically related failure mode occurs on a random basis leading to inconsistency in tool performance, accelerated by fluctuations in thermal and mechanical properties when machining under high pressure coolant supplies.     

TOOL PERFORMANCE AND CHIP CONTROL WHEN MACHINING Ti6A14V AND INCONEL 901 USING HIGH PRESSURE COOLANT SUPPLY

Single point continuous turning tests were carried out on Ti6A14V and Inconel 901 using various geometries of straight grade (K20) cemented carbide inserts using a high pressure coolant jet directed at the tip of the tool where the chip is formed. Trials were also carried out using a conventional coolant supply for comparison. The test results show that improved tool life can be achieved when machining the titanium-base alloy under the high pressure coolant jet while shorter tool life was obtained when machining the nickel-base alloy. The use of high pressure coolant supply during machining generally maintains constant cutting forces and reduces the chip-tool contact length, thus increasing stresses at the tool edge. This behavior tends to accelerate notching that is predominant when machining the Inconel 901 alloy, resulting in shorter tool life. This effect is not obvious when machining Ti6Ai4V where the tools failed mainly due to excessive flank wear. Effective chip control was achieved when machining both materials because of the cyclic fragmentation mechanism of the newly generated chip.     

Study of surface quality in high speed turning of Inconel 718 with uncoated and coated CBN tools

Inconel 718 is known to be among the most difficult-to-machine materials due to its special properties which cause the short tool life and severe surface damages. The properties, which are responsible for poor machinability, include rapid work hardening during machining; tendency to weld with the tool material at high temperature generated during machining; the tendency to form a built-up edge during machining; and the presence of hard carbides, such as titanium carbide and niobium carbide, in their microstructure. Conventional method of machining Inconel 718 with cemented carbide tool restricts the cutting speed to a maximum 30?m/min due to the lower hot hardness of carbide tool, high temperature strength and low thermal conductivity of Inconel 718. The introduction of new coated carbide tools has increased cutting speed to 100?m/min; nevertheless, the time required to machine this alloy is still considerably high. High speed machining using advanced tool material, such as CBN, is one possible alternative for improving the productivity of this material due to its higher hot hardness in comparison with carbide tool. This paper specifically deals with surface quality generated under high speed finishing turning conditions on age-hardened Inconel 718 with focus on surface roughness, metallographic analysis of surface layer and surface damages produced by machining. Both coated and uncoated CBN tools were used in the tests, and a comparison between surfaces generated by both tools was also discussed.     

Analysis of tool wear patterns in finishing turning of Inconel 718

This paper focuses on the analysis of tool wear mechanisms in finishing turning of Inconel 718, one of the most used Ni alloys, both in wet and dry cutting. Cemented carbides, ceramics and CBN tools are suitable for machining Ni alloys; coated carbide tools are competitive for machining operations of Ni alloys and widely used in industry. Commercial coated carbide tools (multilayer coating TiAl/TiAlN recommended for machining Ni alloys) were studied in this work. The feasibility of two inserts tested for dry cutting of Inconel 718 has been shown in the work. Experimental test were performed in order to analyze wear patterns evolution. It was found great influence of side cutting edge angle in tool wear mode.     

Performance of cryogenically treated tungsten carbide tools in milling operations

This paper describes a study on the effects of cryogenic treatment of tungsten carbide. Cryogenic treatment has been acknowledged by some as a means of extending the tool life of many cutting tool materials, but little is known about the mechanism behind it. Thus far, the only few detailed studies conducted pertain to the cryogenic treatment of tool steels. However, tungsten carbide cutting tools are now in common use in industry. This paper primarily reports and analyses the differences in tool performance between cryogenically treated and untreated tungsten carbide tool inserts during the high-speed milling of medium carbon steel. In addition to dry cutting, machining with coolant was also tested. From the results, it can be seen that cryogenically treated tools exhibit better tool wear resistance than untreated ones. Also, it is evident that the application of coolant during cutting helps to reduce tool wear experienced by the cryogenically treated tools even further. In addition, cryogenically treated tools are found to perform best under a particular set of cutting conditions.     

Suppression of notch wear of a whisker reinforced ceramic tool in air-jet-assisted high-speed machining of Inconel 718

This paper describes the notch and flank wear specific to a SiC whisker reinforced alumina tool in air jet assisted (AJA) turning of nickel-base superalloy Inconel 718 at high cutting speeds. An AJA machining experiment has revealed that the air jet applied to the tool tip in addition to coolant dramatically reduces the depth-of-cut notch wear. As a result, the width of flank wear, but not the size of notch wear, determined the life of a ceramic tool in AJA machining of Inconel 718. This is a reason for the large extension and small variation of the tool life when high speed AJA machining is adopted. The maximum tool life length reached 2160 m at a cutting speed of 660 m/min under the given cutting conditions. Finally, the mechanisms of the notch and flank wear of a SiC whisker reinforced alumina tool in AJA machining are discussed from the viewpoints of tribochemical reactions and tool wear anisotropy.     

The Effect of Coolant Concentration on the Machinability of Nickel-Base, Nimonic C-263, Alloy

This paper investigates the effect of coolant concentration on tool performance when machining nickel-base, C-263, alloy with triple coated (TiN/TiCN/TiN) carbide insert at various (3–9%) coolant concentrations and under different cutting speed conditions. Tool life, tool-failure modes, wear rates, component forces and surface finish generated during machining were recorded, analyzed and used to formulate mechanisms responsible for tool wear at the cutting conditions investigated. Analysis of the recorded data shows that tool performance during machining is dependent on coolant concentration. 6% coolant concentration gave the best overall performance as effective combination of cooling and lubrication functions were achieved during machining. Increasing coolant concentration to 9% reduced tool performance due to a reduction of the tool-chip contact length area and the consequent increase in compressive stresses at the tool-chip and tool-workpiece interfaces. This action often leads to pronounced chipping of the tool cutting edge during machining. Friction coefficient between the workpiece material and substrate increases once the coating layer(s) is broken as a result of the direct contact between the tool substrate and the work material. This action increases mechanical wear of the tool, which in turn leads to a significant increase in the cutting force with negligible effect on the feed forces during machining.     

Effect of high-pressure cooling on life of SiAlON tools in machining of Inconel 718

High-pressure cooling has proven to be very effective when machining with carbide inserts. Longer tool life and improved chip breaking are among the most commonly mentioned advantages. Nevertheless, this cooling method has been reported to reduce the life of ceramic tools in machining of heat-resistant alloys. The main reason for that is said to be the accelerated notch wear. Therefore, in this study, SiAlON ceramic inserts with improved resistance to notching were tested in machining of Inconel?718 under high-pressure cooling. The results were compared to conventional cooling. It turned out that, while notch wear was still slightly increased when high-pressure cooling was applied, it was no longer critical for the tool life. Flank wear, on the other hand, was reduced, which led to significantly longer tool life. The variation of the tool life appeared to be slightly less and chip breaking was considerably improved. This shows that, when used properly, high-pressure cooling can help to increase the productivity in machining of heat-resistant alloys with ceramic tools.     

EFFECTS OF CUTTING SPEED WHEN TURNING AGE HARDENED INCONEL 718 WITH PCBN TOOLS OF BINDERLESS AND LOW-CBN GRADES

Application of polycrystalline cubic boron nitride (PCBN) tools as an alternative for ceramic and cemented carbide tools in machining superalloys has been frequently identified as a solution for enhancing process efficiency but only a limited number of studies has been done in this area. The current study explores the effect of the cutting speed, which was varied in a wide range (2–14 m/s), on machinability of age hardened Inconel 718 with PCBN tools. Performance of binderless PCBN grade and grade with low-cBN content was evaluated in terms of tool life, tool wear, cutting forces and surface quality. Chip formation and process dynamics were analyzed as well. It was found that low-cBN grade provided 70–90% better surface finish and tool life than the binderless at moderate speeds (5–8 m/s). Performance of both grades at low and high speed ranges was non-satisfactory due to notching and flaking respectively. At low cutting speed adhesive wear plays a major role while as the speed increases a chemical wear becomes dominant.     

Performance and wear mechanisms of whisker-reinforced alumina, coated and uncoated PCBN tools when high-speed turning aged Inconel 718

Inconel 718, an efficient superalloy for energy and aerospace applications, is currently machined with cemented carbide tools at low speed (v _c?≈?60 m/min) due to its unfavorable mechanical and thermal properties. The article presents results of a study of superalloy machinability with whisker-reinforced alumina, uncoated and coated polycrystalline cubic boron nitride (PCBN) tools. Turning of age-hardened Inconel 718 (45 HRC) was done under high-speed machining conditions (v _c?=?250…350 m/min). Aspects of tool life, tool wear, and generated surface quality were studied. Application of uncoated PCBN tools resulted in surface quality and force level superior to other tool materials. Considerable sideflow of workpiece material was found to affect surface quality, especially for coated PCBN and ceramic tools. It was found that protective function of the coating, which increases the tool life up to 20 %, is limited only to low cutting speed range. EDX and AFM analyses suggested dominance of chemical and abrasive wear mechanisms. EDX mapping of worn tools pointed absence of diffusional wear for PCBN tools and intensive degradation of whisker reinforcement in ceramic tools due to diffusion of Ni, Fe, and Cr.     

Evaluation of the Machinability of Nickel-Base,Inconel 718, Alloy with Nano-Ceramic Cutting Tools

The machinability of difficult-to-cut aerospace alloys can be enhanced by the rapid development of cutting tool materials that can withstand machining at high-speed conditions. The performance of nano-grain size ceramic tool materials were evaluated when machining nickel base, Inconel 718, in terms of tool life, tool failure modes and wear mechanisms as well as component forces generated under different roughing conditions. Comparison tests were carried out with commercially available ceramic tool materials of micron-grain composition.

The test results show that the micron grain size commercially available tool materials generally gave the longest tool life. The dominant failure mode is nose wear, while some of the nano-ceramic tools were rejected mainly due to chipping at the cutting edge. This suggests that physical properties and mechanical stability of the cutting edge of the ceramic tools influence their overall performance. It is also evident that chemical compositions of the tool materials played a significant role in their failure. The alumina base ceramics are more susceptible to premature fracture than the silicon nitride base ceramics with higher fracture toughness.     

Development of a novel cubic boron nitride cutting tool with a textured flank face for high-speed machining of Inconel 718

Nickel-based superalloys such as Inconel 718 offer several advantages, including high-temperature strength and high corrosion resistance; this has led to a rapid increase in the demand for such materials, particularly in the aircraft industry. In contrast, these alloys are known to be among the most difficult-to-cut materials because of their mechanical and chemical properties, and tools used for this purpose have extremely short lifetimes. Recently, cubic boron nitride (CBN), which is the second hardest of all known materials, has received significant attention as a material for cutting tools and has already established itself in many fields of application. However, the performance of CBN tools is still insufficient for practical use, especially in the high-speed machining of Inconel 718. To overcome this problem, we first conducted orthogonal cutting experiments on Inconel 718 and performed cross-sectional observations of the CBN cutting tool in order to identify its wear mechanisms in continuous cutting operations under high-speed machining conditions (300 m/min). As a result, it was found that fatal tool failure occurs through crater and flank wear because of diffusion led by high cutting temperatures and subsequent chip adhesion to the tool flank face, accompanied by cutting edge chipping. Based on these results, a CBN cutting tool with a textured flank face was newly developed to improve the cutting tool life. Experimental: results showed that micro grooves generated on the flank face significantly suppressed the cutting edge chipping and remarkably extended the lifetime of the CBN tool during high-speed machining of Inconel 718.     

Carbide tool wear mechanism in turning of Inconel 718 superalloy

Wear surfaces of the cutting tools are analyzed to study the wear mechanism of cemented carbide tools in turning in Inconel 718 superalloys. SEM and EPMA analyses indicated that the wear of carbide tools during high speed turning condition (V = 35 m min⁻¹) was caused by diffusion of elements (Ni or Fe) in workpiece into tool's binder (Co) by a grain boundary diffusion mechanism. This action weakened the bonding strength between carbide particles (WC, TiC, TaC) and the binder (Co). The carbide particles were then detached out of the cemented carbide tool by high flow stresses. The proposed grain boundary diffusion mechanism is also confirmed by theoretical analysis.     

Study of surface quality in machining nickel-based alloy Inconel 718

In machining operation, the surface quality is one of the most important requirements for many workpieces. Because of the special physical and chemical properties, good-machined surface quality becomes a key issue to solve in machining Inconel 718. In this paper, PVD-TiAlN-coated carbide tools were used to turn Inconel 718. Based on observing the tool wear and machined surface morphology, the main factors affecting surface quality at different cutting speeds were analyzed. The optimal cutting temperature was calculated, according to the above analysis and Archard adhesion wear model, and further cutting parameters optimization was conducted, on the basis of the proposed optimal cutting temperature. The optimized cutting parameters based on optimal cutting temperature can be considered to improve surface quality.     

Effects of Coating Materials on the Machinability of a Nickel Base,C-263, Alloy

PVD coated (TiN/TiCN/TiN, TiAIN and TiZrN) and uncoated carbide tools were used to machine a nickel base, C-263, alloy at high-speed conditions. The test results show that the multiple TiN/TiCN/TiN coated inserts gave the best overall performance in terms of tool life when machining at cutting speeds up to 68 m min and at depths of cut of 0.635 mm, 1.25 mm and 2.54 mm. All the tool grades tested gave fairly uniform surface roughness (Ra) values, below the rejection criterion, at lower speed conditions. The TiZrN coated inserts gave the lowest component forces when machining at lower cutting speed conditions while the TiA/N coated inserts gave the lowest component forces when machining at a higher speed of 68 m min^?1 and depth of cut of 1.25 mm. This tool performance can generally be attributed to the difference in their ability to provide effective lubrication at the cutting zone, thermal conductivity of the coating materials as well as the cutting conditions employed. The uncoated carbide tools generally encountered more severe crater wear, chipping/fracture of the cutting edges as well as pronounced notching during machining. This is due to their inability to provide effective lubrication at the cutting zone, thus impeding the gliding motion of the chips along the rake and flank faces respectively, thus accelerating flank wear. Analysis of the worn tool edges revealed adhesion of a compact “fin-shaped” structure of hardened burrs with saw-tooth like edges. This generally alters the initial geometry of the cutting edge, consequently resulting to poor surface finish with prolonged machining.     

涂层硬质合金刀具切削Inconel718合金的有限元分析

采用Third Wave AdvantEdge切削仿真软件对Inconel 718合金进行车削有限元模拟,通过2D有限元模块分析了单层/多层涂层硬质合金刀具,在不同切削速度下的切削力、进给力和切削温度,以及涂层厚度对切削性能的影响,研究结果对新刀具材料和涂层的设计具有一定指导作用。     

用于加工Inconel718的切削刀具发展现状

镍基高温合金Inconel718具有熔点高、热传导率低、加工硬化现象严重的特点,被认为是最难加工的金属材料之一。近年来,随着航空航天、能源动力技术的飞速发展,Inconel718高温合金的应用越来越多,其高速、高效切削的加工需求也日益扩张,其切削工艺的制定、尤其是切削刀具的选择越来越重要。本文综述了常用于加工In-conel718的刀具(高速钢、硬质合金、陶瓷、立方氮化硼)及其涂层刀具的加工性能,分析了不同涂层对于刀具寿命和工件表面质量的影响,对硬质合金刀具和陶瓷刀具作了详尽的对比分析。最后,对高速钢、陶瓷、硬质合金和立方氮化硼刀具切削Inconel718的应用情况进行了总结,给出了Inconel718高温合金切削加工刀具选择的有益参考。     

The Effect of Argon-Enriched Environment in High-Speed Machining of Titanium Alloy

A major factor hindering the machinability of titanium alloys is their tendency to react with most cutting tool materials, thereby encouraging solution wear during machining. Machining in an inert environment is envisaged to minimize chemical reaction at the tool-chip and tool-workpiece interfaces when machining commercially available titanium alloys at higher cutting conditions. This article presents the results of machining trials carried out with uncoated carbide (ISO K10 grade) tools in an argon-enriched environment at cutting conditions typical of finish turning operations. Comparative trials were carried out at the same cutting conditions under conventional coolant supply. Results of the machining trials show that machining in an argon-enriched environment gave lower tool life relative to conventional coolant supply. Nose wear was the dominant tool-failure mode in all the cutting conditions investigated. Argon is a poor conductor of heat; thus, heat generated during machining tends to concentrate in the cutting region and accelerate tool wear. Argon also has poor lubrication characteristics, leading to increasing friction at the cutting interfaces during machining and an increase in cutting forces required for efficient shearing of the workpiece.     

Cutting performance and wear mechanisms of Sialon–Si3N4 graded nano-composite ceramic cutting tools

Sialon–Si₃N₄ graded nano-composite ceramic tool materials were fabricated by using hot-pressing technique. The residual stresses in the surface layer of the graded ceramic tool materials were calculated by the indentation method. The cutting performance and wear mechanisms of the graded tools were investigated via turning of Inconel 718 alloy in comparison with common reference tools. The surface roughness of the finish hard turning of Inconel 718 and the microstructures of the chips were also examined. Worn and fractured surfaces of the cutting tools were characterized by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The results showed that graded structure in Sialon–Si₃N₄ graded ceramic tool materials can induce residual compressive stresses in the surface layer during fabrication process. Tool lifetime of graded ceramic tool was higher than that of the common reference tool. The longer tool life of the graded nano-composite ceramic tool was attributed to its synergistic strengthening and toughening mechanisms induced by the optimum graded compositional structure of the tool and the addition of nano-sized particles. Wear mechanisms identified in the machining tests involved adhesive wear and abrasive wear. The mechanisms responsible for the higher tool life were determined to be the formation of compressive residual stress in the surface layer of the graded tools, which led to an increase in the resistance to fracture.     

Experimental investigations from conventional to high speed milling on a 304-L stainless steel

Last years analytical or finite element models of milling become more efficient and focus on more physical aspects, nevertheless the milling process is still experimentally unknown on a wide range of use. This paper propose to analyse with accuracy milling operations by investigating the cutting forces values, shape of cutting forces curves obtained for different cutting speeds, and related phenomena as tool wear or tool run-out. These detailed experimental data in milling constitute a suitable experimental basis available to develop predictive machining modelling. All the tests have been conducted on the 304-L stainless steel in many cutting configurations and for different tool geometries. The machinability of the 304-L stainless steel with different tools geometries and configurations in shoulder milling is defined by three working zones: a conventional zone permitting stable cutting (low cutting speed; under 200–250 m.min^?1), a dead zone (unfavourable for cutting forces level and cutting stability; between 250 and 450 m.min^?1), and a high speed machining zone (high cutting speed; up to 450–500 m.min^?1). All the used criteria (cutting forces, chips, wear) confirm the existence of these different zones and a correlation is proposed with cutting perturbations as tool run-out, cutting instability, ploughing, and abrasive wear.