原位反应生成TiB2对B4C/TiB2复合陶瓷力学性能和结构的影响

研究了原位反应生成TiB2对B4 C/TiB2复合陶瓷维氏硬度、断裂韧度、抗弯强度和微观结构的影响.结果表明,适量TiB2的生成可以抑制B4C/TiB2复合陶瓷晶粒的长大,可使材料获得均匀致密的显微组织结构;而且原位反应的发生促使B4C/TiB2复合陶瓷断裂机制由穿晶断裂为主转变为穿晶与沿晶结合的断裂机制.B4C和TiB2晶粒尺寸都随着原位生成TiB2含量的增加而降低.B4C/TiB2复合陶瓷的抗弯强度随晶粒增大而降低,其断裂韧度随晶粒尺寸的变化关系较为复杂,这种变化关系主要与断裂韧度对裂纹扩展路径长度的依赖性有关,本文利用裂纹扩展阻力(R)曲线的斜率解释了这种变化.     

Ti 元素对B4C/Al复合材料力学性能的改善作用研究

B₄C/Al复合材料是目前最理想的中子吸收材料,广泛用于乏燃料储存。本文利用液态搅拌法制备B₄C/Al复合材料,通过添加Ti元素,探讨了界面反应对材料的界面结构和力学性能的影响。研究发现,Ti元素通过参与界面反应,改变了界面结构,在B₄C颗粒表面形成了紧密结合的纳米TiB₂界面层;Ti的添加消除了界面微裂纹、微孔、分离等缺陷。随着界面反应程度的加强,材料强度提高,尤其反应脱落的纳米TiB₂颗粒作为原位第二强化相进一步增强基体。B₄C/Al复合材料断裂过程表现为韧窝延性断裂;TiB₂界面层增强了B₄C颗粒与基体的结合,断裂行为从B₄C-Al界面脱落转变为B₄C颗粒断裂;但过渡的界面反应会形成微韧窝,引起材料延伸率下降。     

Synthesis of B4C-Nano TiB2 Composite Powder by Sol-Gel Method

Production of (B₄C-nano TiB₂) composite powder by chemical method was evaluated in this study. Starting materials were boron carbide, carbon, and titanium (IV) iso propoxide (TTIP). Water was used as a hydrolyser agent. TTIP was hydrolyzed with water and, consequently, amorphous Ti(OH)₄ was formed. Heat-treatment of Ti(OH)₄ at 100 and 850 °C led to the production of TiO₂ and TiB₂ phases, respectively. The effect of heat-treatment time and temperature on the phase transformation and size of the produced nano powder were investigated. The produced nano powder was characterized by XRD, SEM, and DTA. It was found that heat-treatment time and temperature have significant effects on the amount and size of the produced TiB₂ powder. The data also reveal that the minimum temperature for TiB₂ formation is 650 °C.     

原位热压反应制备Ti3AlC2／TiB2复合材料

Ti3AlC2综合了陶瓷和金属的诸多优点，有着潜在的广泛应用前景。然而，单相Ti3AlC2的硬度和强度偏低，限制了它的广泛应用。引入第二相形成复合材料是解决上述问题的一个有效方法。以Ti粉、Al粉、石墨和B4C粉为原料采用原位热压方法成功地合成了Ti3AlC2/TiB2复合材料。利用DSC和XRD对其反应路径作了详细研究，并利用SEM和TEM对复合材料的微观结构进行了表征，最后测试了复合材料的硬度和强度。结果表明用B4C-Ti-Al-C体系，可以在较低温度下合成致密的无杂质Ti3AlC2／TiB2复合材料；引入的TiB2明显提高了Ti3AlC2的硬度和强度。     

原位自生TiB2/Al复合材料的组织与力学性能

采用钛盐与硼盐反应法成功制备原位自生TiB2/纯Al复合材料。利用扫描电子显微镜、透射电子显微镜和拉伸试验机研究不同粒子含量(质量分数为1%、2%和3%)对复合材料组织和力学性能的影响。结果表明:原位生成的TiB2粒子有矩形、近圆形和六边形三种形貌,尺寸为200~500 nm;粒子与Al基体界面洁净无反应层。随着粒子含量的增加,复合材料的强度随之升高,而伸长率则随之降低;当TiB2含量为3%时,屈服强度和抗拉强度分别达到78.1 MPa和102 MPa,相比于纯Al分别提高58%和43%,而伸长率降至32.5%,下降了24%。断口分析表明:随着TiB2粒子含量的增加,粒子团聚机率增加,在拉伸过程中,裂纹在粒子团聚处萌生并扩展,导致材料的塑性降低。     

Cyclic oxidation behavior of TiAl composites incorporated with TiB2 dispersoids

TiAl alloys incorporated in (0,3,5,10) wt.% TiB₂ dispersoids were manufactured via mechanical alloyingspark plasma sintering (MA-SPS), and their cyclic oxidation characteristics were studied at 800, 900 and 1000°C in air. The cyclic oxidation resistance of the prepared TiAl-TiB₂ composites effectively increased with increases in TiB₂ content. The oxide scale formed consisted of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner (Al₂O₃+TiO₂) mixed layer. The scale adherence was relatively good, and much thinner oxide scales, when compared to TiB₂-free TiAl alloys, were formed on the prepared composites. The incorporated TiB₂ dispersoids oxidized to TiO₂ and B₂O₃ which evaporated during oxidation.     

Investigation on microstructure and internal friction for low density TiB2/ZL114 composites

TiB₂/ZL114 composites with the density of 2.733 g/cm³ were fabricated through reaction of K₂TiF₄ and KBF₄ (LSM method). The composites were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The internal friction measurements were performed on DTM-II-J dynamic modulus damping analyzer and the mechanisms were investigated. Experimental results indicate that reinforced particles are well-distributed in the matrix and the internal friction value of TiB₂/ZL114 composites is up to a maximum of 9.04x10^-3, almost twice that of ZL114. The internal friction results form dislocation vibration within the material, the sliding of grain boundary and phase interface, and together with the micro-plastic deformation caused by difference in coefficients of thermal expansion and elasticity modulus of various phases. The average internal friction values of samples with the sizes of 40 mmx4 mmx2 mm, 40 mmx8 mmx2 mm and 40~mm$\times 25 mmx2 mm are 8.83x10^-3, 8.89x10^-3, and 8.93x10^-3, respectively. Thus, the developed composites are of low density, high internal friction, and the sizes of samples have no relation to the internal friction behavior.     

原位反应纳米TiB2/Cu复合材料的制备和微结构

利用原位反应技术 ,通过控制反应物B2 O3 和石墨的含量制备了原位生长纳米TiB2 增强Cu基复合材料。用XRD ,EDS ,TEM对TiB2 /Cu原位复合材料进行微结构分析 ,研究表明铜基体中弥散分布着 5 0nm的TiB2颗粒 ,并对Cu基体有良好的增强作用。     

The Oxidation of TiB2 Ceramics Containing Cr and Fe

The oxidation behavior of TiB₂, TiB₂–0.5 wt.% Cr–0.5 wt.% Fe and TiB₂–1 wt.% Cr–1 wt.% Fe was studied at 800, 900, and 1000°C in static air. These ceramics oxidized rather rapidly and formed thick oxide scales. The oxidation rates of TiB₂-base ceramics were comparable to TiO₂ formation on pure titanium. The scale formed on TiB₂ consisted of TiO₂ and B₂O₃. For TiB–Cr–Fe ceramics, a small amount of Cr- and Fe-oxides was additionally formed. B₂O₃ formed during oxidation tended to evaporate because of its high vapor pressure, making oxide scales porous and fragile. The oxidation of the TiB₂-base ceramics appeared to be governed by the inward transport of oxygen via the highly porous oxide scale. The oxidation resistance of TiB₂–Cr–Fe ceramics was similar to or better than that of TiB₂.     

半固态热等静压Al/B4C复合材料液相流动行为与致密化机理

铝基碳化硼复合材料是一种重要的中子吸收材料。为了制备具有更高密度的铝基碳化硼材料,研究采用粉末冶金半固态热等静压方法制备了含量为30%碳化硼的铝基碳化硼材料,采用WANCE100型材料力学性能试验机和SIRION200型扫描电镜研究了复合材料的力学性能及显微形貌。结果表明：半固态热等静压工艺可制备获得接近理论密度的Al/B4C复合材料;虽然Al/B4C材料抗拉强度可提升至约300Mpa,但过高碳化硼含量也使得该材料脆性特征十分明显;研究同时采用间接的方法观察到了半固态工艺过程中生成的液相,该液相不仅可改善碳化硼颗粒与铝基体的结合性,在高温高压下液相的流动还起到填充复合材料内部空隙的作用。半固态热等静压工艺过程中产生的液相是复合材料密度和机械性能提升的主要原因。     

固溶处理对TiB2/6061复合材料硬度及耐磨性的影响

采用氟盐法制备了TiB₂质量分数为3%的原位合成TiB₂/6061复合材料,研究了固溶温度和固溶时间对复合材料硬度和耐磨性能的影响。结果表明:TiB₂颗粒弥散分布在6061铝合金基体中,明显细化6061铝合金基体晶粒。当固溶温度一定时,随固溶时间延长,复合材料的硬度和耐磨性可获得明显提高,但固溶时间在6~10 h时,复合材料的性能变化不显著。当固溶时间一定时,随固溶温度升高,复合材料硬度和耐磨性呈现先上升后下降的趋势。3wt%TiB₂/6061复合材料经530 ℃×10 h固溶处理后,硬度和耐磨性能最佳,相较于铸态硬度值提高了79.5％,磨损量减少了59.1%。固溶处理后复合材料的磨损表面犁沟变细变浅,材料脱落现象减少。     

Al2O3/TiB2/Al复合材料的微观结构和高温力学性能

以细雾化铝粉和TiB₂颗粒为原料,通过粉末冶金和热轧制制备微米TiB₂和纳米Al₂O₃颗粒增强铝基复合材料。室温时,由于TiB₂和Al₂O₃的综合强化作用,Al₂O₃/TiB₂/Al复合材料的屈服强度和抗拉强度分别为258.7 MPa和279.3 MPa,测试温度升至350℃时,TiB₂颗粒的增强效果显著减弱,原位纳米Al₂O₃颗粒与位错的交互作用使得复合材料的屈服强度和抗拉强度达到98.2MPa和122.5 MPa。经350℃退火1000 h后,由于纳米Al₂O₃对晶界的钉扎作用抑制晶粒长大,强度和硬度未发生显著的降低。     

原位合成TiC和TiB增强钛基复合材料的微观结构与力学性能

利用钛与Ｂ４Ｃ之间的自蔓延高温合成反应经普通的熔钐工艺原位合成制备了ＴｉＣ、ＴｉＢ增强的钛基复合材料。光学金相、ＥＰＭＡ、ＴＥＭ和Ｘ射线衍射的研究结果表明：存在匠两种不同形状的增强体,即短纤维状ＴｉＢ晶须和等轴、近似等轴状ＴｉＣ粒子。ＴｉＢ、Ｔｉ基体界面洁净,没有明显的界面反应,而ＴｉＣ、Ｔｉ基体界面有非化学配比的ＴｉＣ过度层存在。由于增强体承受载荷,基体合金晶粒细化以及高密度位错的存在,制备钛基     

TiB2含量和烧结温度对B4C/Al2O3基复合陶瓷的影响

利用原位反应热压工艺制备了B4C/Al2O3基复合陶瓷,研究了TiB2含量和烧结温度对B4C/Al2O3基复合陶瓷力学性能和微观结构的影响.结果表明,当TiB2含量低于8.7％时,随原位反应生成的TiB2含量的增加,有效的促进了B4C/Al2O3/TiB2复合陶瓷的烧结,提高相对密度,改善了力学性能.当烧结温度低于1900℃时,其力学性能随烧结温度增加而提高;当超过1900℃时,其力学性能随烧结温度的提高而降低.在1900℃,60 min时,B4C/Al2O3/TiB2复合陶瓷获得最佳综合力学性能,其硬度、断裂韧性和抗弯强度分别为24.8 GPa、4.82 MPa·m1/2和445.2 MPa.     

Comparison of vacuum and pressure-assisted sintering of TiB2-Ni

A relatively new generation of cermet materials, based on TiB₂-Ni, has been investigated. These borides currently are being examined for industrial applications with the aim of exploiting their excellent wear resistance. Optimization of the liquid-phase sintering process for a TilB₂-Ni composition was studied. The mechanical properties of cermet materials prepared using vacuum and pressure sintering techniques were determined. Criteria for optimal sintering conditions were established according to hardness, strength, and fracture toughness properties.     

放电等离子烧结TiB/Ti-1.5Fe-2.25Mo复合材料的微观组织与力学性能

采用放电等离子烧结技术原位合成了TiB增强Ti?1.5Fe?2.25Mo复合材料,研究了烧结温度对复合材料微观组织和力学性能的影响规律。结果表明,随着烧结温度的升高,钛合金中 TiB 晶须的长细比迅速减小;然而,复合材料的相对密度及TiB的体积含量随着烧结温度的升高而不断增大。由于TiB晶须长细比的减小会导致复合材料强度的降低,而复合材料的相对密度及TiB体积含量的增大又会带来复合材料强度的增加,因此,在这两种因素的共同作用下,最终导致 TiB/Ti?1.5Fe?2.25Mo复合材料的弯曲强度随着烧结温度的升高而缓慢增大。在烧结温度为1150°C 时,TiB/Ti?1.5Fe?2.25Mo复合材料具有最大的弯曲强度1596 MPa。     

Structural evolution of mechanically alloyed Al-12Si/TiB2/h-BN composite powder coating by atmospheric plasma spraying

In the present study, mechanically alloyed Al-12Si/TiB₂/h-BN composite powder was deposited onto an aluminum substrate by atmospheric plasma spraying. The effect of mechanical alloying (MA) and plasma spray parameters on composite powder and coating structure were investigated. It has been observed that the MA process has a significant effect on the composite powder morphology and reactivity between the selective powders. Results also demonstrate that, at relatively high milling time h-BN decomposes into B and N and forms a solid solution. Also, it has been found that, the relative amount of the in-situ formed AlN through the reaction between h-BN and Al and/or the decomposition of Al-B-N solid solution is independent from the plasma parameters (arc current and secondary gas flow rate). However, spray parameters remarkably affects the coating hardness due to coarsening of Si during the solidification of the coating.     

原位热压反应制备Ti3AlC2/TiB2复合材料

Ti3AlC2综合了陶瓷和金属的诸多优点,有着潜在的广泛应用前景.然而,单相Ti3AlC2的硬度和强度偏低,限制了它的广泛应用.引入第二相形成复合材料是解决上述问题的一个有效方法.以Ti粉、Al粉、石墨和B4C粉为原料采用原位热压方法成功地合成了Ti3AlC2/TiB2复合材料.利用DSC和XRD对其反应路径作了详细研究,并利用SEM和TEM对复合材料的微观结构进行了表征,最后测试了复合材料的硬度和强度.结果表明用B4C-Ti-Al-C体系,可以在较低温度下合成致密的无杂质Ti3AlC2/TiB2复合材料;引入的TiB2明显提高了Ti3AlC2的硬度和强度.