塑料光纤纤端光场测试结果及分析

对纤端光场进行了理论分析,分别利用塑料光纤和多模光纤作为接收光纤对塑料光纤的出射纤端光场进行了测量,并与理论分析结果进行了比较,给出了合理的调和参数.传输距离较长的塑料光纤由于高阶模的泄漏,纤端光场分布非常接近高斯分布.实验结果表明了理论分析结果和调和参数选择的合理性.     

大容差光纤耦合技术研究

设计了一种新型的耦合系统,该耦合系统由大口径聚焦透镜、1/4节距自聚焦透镜、锥形光纤和球端光纤四部分组成.分析了自聚焦透镜压缩发散角和球端光纤增大数值孔径的机理,给出了计算锥形光纤参量的详细流程.采用大口径透镜和1/4节距自聚焦透镜有效增大径向位置容差和角度容差,然后通过锥形光纤压缩光束半径将激光耦合进球端光纤.仿真实验结果表明,该系统耦合在r<3 mm,－1<θ<1.5范围内的耦合效率稳定保持在50%以上.     

光纤传光束敛集率及其填充率的计算

采用二种方式推算了光纤采用六边形排列配用圆形端套光纤传光束的理论敛集率,其值为90.69%,这一值同光纤采用六边形排列配用长方形端套的传光束理论敛集率一致.而单根粗直径聚合物光纤和液芯光纤配用圆形端套制作的光纤传光束,其敛集率为100%,在可见光或紫外光范围内,选用单根粗直径聚合物光纤或液芯光纤传光束具有更多的优势.分析了皮层的厚度对光纤传光束或传像束填充率的影响,当光纤半径低于250 μm时,皮层厚度对细直径光纤传光束或传像束填充率影响明显,而当光纤半径大于等于500 μm,皮层厚度的影响相对较小.     

高功率光纤端帽实现6kW激光输出

高功率光纤端帽是kW级光纤激光器必不可少的器件,而实现光纤端帽的低损耗高强度熔接是其关键技术。由于光纤和大尺寸光纤端帽在直径上的巨大差异,二者的熔接不能通过传统熔接机实现。设计并搭建了光纤端帽熔接系统,掌握了多种尺寸的光纤端帽的熔接工艺,成功用于光纤激光器及光纤合束器的高功率输出。实验上利用单模光端帽实现了3.01kW的激光输出,在未进行主动制冷的情况下温升为7℃/kW。利用多模光纤端帽实现了6.08kW的激光输出,在未进行主动制冷的情况下温升为6℃/kW。     

大直径光纤端帽的制作与熔接

为了避免高功率光纤激光器输出的激光对双包层光纤端面造成损伤,设计并制作了光纤端帽。使用新型CO2激光器光纤熔接机完成了双包层光纤与端帽的熔接,研究了双包层光纤与端帽熔接的相关工艺与方法。利用高功率连续激光对端帽的性能进行了测试,实验结果表明,熔接有光纤端帽的双包层光纤可以承受507 W连续激光的输出并且没有发生损伤。熔接有端帽的光纤激光器的斜率效率为64.05%,光束质量与未熔接有端帽时相同。     

光纤耦合LD输出光场特性研究

根据光纤传输的模式理论,分析了单芯光纤输出端面的光场分布.利用单模光纤测量了纤端光场的强度分布,拟合了光纤输出端面光强分布的近似表达式.根据此数值计算和实验测量了多芯光纤输出端面的强度分布,结果基本吻合.表明光纤出射端面的光强分布应是介于高斯分布和几何分布之间的一种准高斯分布.     

熔锥直线型3×3单模光纤定向耦合器的光功率耦合分析

本文利用组合波导理论对熔锥直线型3×3单模光纤定向耦合器中的光功率耦合行为进行了详细的分析,并对该种耦合器的中心端光纤和旁边端光纤注入光能分别进行了讨论,前者得到了预期的结果,后者的结果与前者不同,却是十分有用的.这两种分析结果与实验结果相符.     

推扫式红外光纤传像光学系统研究

针对推扫式红外遥感成像技术在高分辨对地观测领域的重要地位,结合我国红外遥感技术发展现状和长线阵红外探测器技术水平,研究了利用线面转换的异型红外光纤传像束线阵端实现推扫,面阵端与成熟的小面阵红外探测器耦合以获得高分辨红外遥感图像的光纤传像系统.分析了该红外光纤传像系统前置物镜和耦接镜设计中的主要问题,并针对一种入射端为4 000×6元线阵,出射端为160×150元面阵的红外光纤传像束设计了前置物镜系统和后继耦接镜系统.引入平均传递函数的方法对整体光学系统的MTF进行了模拟评价,模拟结果显示整体光学系统成像良好,两系统的成像性能皆达到衍射极限,满足光纤传像系统的特殊要求,可为该类光纤传像系统的设计提供参考.     

光纤耦合激光束输出光空间分布及其影响因素分析

通过分析光纤出射端面的光强分布,研究了光纤传输过程中激光二极管出射光束进入光纤时的指向角对出射端面光场分布的影响.提出一种影响光纤输出端光场的新因素,对数值孔径和光纤芯径两个影响因素进行了补充.在光纤传输过程中,将激光二极管出射的光束等效为大量光线,在二极管输出光的位置以及空间分布确定的情况下,使用光线追迹方法依次分析了单束和多束光的指向角以及光纤长度对出射面光强分布的影响.结果显示:单束入射光指向角的偏差会引起光纤输出端面光强极值位置的偏移,多束的情况可以导致光纤输出端光强呈现明显的环状分布,得出了入射光束指向角的偏差是影响光纤出射面光强分布和峰值位置的重要因素的结论,而光纤长度的变化对上述分布状况同样存在影响.     

一体化光纤滤除器和端帽实现20 kW激光输出北大核心CSCD

在高功率光纤激光系统中,包层光滤除器能将光纤中包层光滤除以保证输出激光光束质量,光纤端帽通过对输出激光扩束降低输出光纤端面的光功率密度,从而保护光纤端面不受损坏,两者都是高功率光纤激光系统稳定运行的重要核心器件。将包层光滤除器和光纤端帽进行一体化设计,制备了一体化高功率光纤包层光滤除器和光纤端帽并分别应用于20 kW合束系统和单纤系统中,输出功率达到20 kW时,端帽的最高温度约为40℃,温升速率约为0.8℃/kW。     

Mapping misoriented fibers using X-ray dark field tomography

X-ray grating interferometers produce three distinct signals; an absorption signal, a differential phase signal and a dark field signal. Until now a method for successfully creating dark field tomograms of nonisotropic samples has not been demonstrated. In this paper we test a method for creating such tomograms on a highly nonisotropic sample, i.e. a five layer “sandwich” of oriented carbon fibers. The fibers are parallel within the individual sandwich layers, but perpendicular to the fibers in the adjacent layers. We show that by choosing a rotation axis parallel to the grating stepping direction (i.e. a horizontal rotation axis in most setup configurations) it is possible to produce a darkfield tomogram where fibers parallel to the probed scattering direction appear to have no dark field signal. The method produces a tomogram in the form of a scalar field of dark field scattering values.     

光纤转动引起光纤光谱效率变化与改正

光纤的焦比退化(focal ratio degradation)是光纤光谱效率损失的重要原因之一。光纤在安装和每次定位过程中,光纤的转动和扭曲会引起光纤焦比退化发生变化,从而改变光纤的传输效率,每根光纤由此造成的传输效率变化都会存在差异。而这样的效率差异无法用通常天文观测中使用的晨昏天光平场或者圆顶平场改正。减天光是光纤光谱数据处理中决定光谱质量的重要环节。减天光处理要求对不同光纤的传输效率进行归一化处理,以扣除不同光纤之间传输效率差异导致的天光背景测量的误差。对于与天光背景亮度接近乃至更暗的观测目标而言,光纤传输效率的改正精度决定了减天光的精度。测试了LAMOST望远镜光纤转动对光纤传输效率的影响情况。在检查了光谱中天光发射线强度与光纤传输效率的关系,和验证了光纤效率变化与波长变化相对独立的基础上,提出并且证实了通过测量各光纤中天光发射线强度作为光纤相对效率变化量来改正光纤效率差异的方法是可行的。这种方法已经被应用到LAMOST二维光谱处理当中。     

保偏光纤双折射主轴的旋转对消光比的影响

本文利用无穷切片模型和Jones矩阵理论,给出了主轴连续旋转的保偏光纤的等效矩阵,并讨论了主轴旋转对消光比的影响.     

Rotation of Mo-Fibers in Directionally Solidified Ni-Al-Mo Eutectic Alloys

The interface structure of -Mo fib ers in directionally solidified Ni-Al-Mo eutectic alloys has been investigated by transmission electron microscopy and computer-aided graphical techniques. The Mo fibers have square or rectangular cross sections with well defined flat facets and fundamentally have the Bain orientation relationship with respect to the matrix lattice. The crystal lattices of the Mo fibers, however, are often rotated with respect to the matrix lattice about their longitudinal axes. Correspondingly, the facet planes deviate from the exact rational (1 1 0)//(1 0 0) relationship. A computer aided graphical plotting of the atom arrangement at the interfaces suggests that good atomic matching is kept even after the rotation of fibers. High resolution electron microscopy revealed the incorporation of single atomic structural ledges to keep the coherency of the lattices of the matrix and rotated fibers. The relation between the lattice rotation and the facet plane rotation is well explained by the moiré and O-lattice models.     

Effect of the architecture of the left ventricle on the speed of the excitation wave in muscle fibers

It is known that preferential paths for the propagation of an electrical excitation wave in the human ventricular myocardium are associated with muscle fibers in tissue. The speed of the excitation wave along a fiber is several times higher than that across the direction of the fiber. To estimate the effect of the architecture and anisotropy of the myocardium of the left ventricle on the process of its electrical activation, we have studied the relation between the speed of the electrical excitation wave in a one-dimensional isolated myocardial fiber consisting of sequentially coupled cardiomyocytes and in an identical fiber located in the wall of a threedimensional anatomical model of the left ventricle. It has been shown that the speed of a wavefront along the fiber in the three-dimensional myocardial tissue is much higher than that in the one-dimensional fiber. The acceleration of the signal is due to the rotation of directions of fibers in the wall and to the position of the excitation wavefront with respect to the direction of this fiber. The observed phenomenon is caused by the approach of the excitable tissue with rotational anisotropy in its properties to a pseudoisotropic tissue.     

Effect of fiber-spinning profile on plug-and-play quantum-key distribution systems

The spin profile of a fiber is usually optimized to reduce transmission impairments caused by polarization-mode dispersion (PMD). In this paper, we show that fiber-optic-based plug-and-play quantum-key distribution systems using polarization modulation and fibers with a spin profile optimal for PMD may suffer from a large Faraday rotation induced by the geomagnetic field. We show that, for periodic spin patterns of small periods, the Faraday rotation is minimum when no spin is applied to the fiber.     

EAST װ����ERD �������ϵͳ���

A new edge rotation diagnostic system (ERD) was developed to measure the edge plasma rotation velocities and ion temperature profiles toroidally and poloidally. The collective optics adopts the ‘plug-in’ concept and is very flexible for additional system adjustment and maintenance after installation. For the spectrometer, a multi-slit entrance is used to effectively improve the capacity of the spectrometer and accommodate more optical fibers. A back-illuminated EMCCD is adopted as the photon detector for its high sensitivity and wide dynamic range. The high OH-radical concentration fused silica fibers are adopted to resist the neutron radiation. The system is in the visible wavelength range (350~800nm), the achieved temporal and spatial resolution is 15ms and 1cm respectively. Experimental results during the LHW phase are consistent with the collaborative experimental results from the XCS and fast reciprocating probe.     

多叶应力区扭转光纤的耦合模理论

从线性极化模的耦合模理论出发,分析了双叶应力区扭转光纤,即扭转保偏光纤,和四叶应力区扭转光纤.推导应力引起的在光纤芯区各向异性的介质张量表达式;利用该表达式得到线性极化模在有转角时的多叶应力区光纤中传输的耦合模方程;从而推得多叶应力区扭转光纤中的超本地模,由超本地模的相位常数来确定该光纤的双折射.在双叶、四叶应力区理想对称的条件下,前者可以得到较高的椭圆双折射,而后者则无任何双折射.同样的结论可推广到8叶或16叶的扭转光纤,都无任何双折射.     

Simulation of the speckle pattern rotation in an absorbing optical fiber under the change of sign of the circular polarization of propagating light

The effect of rotation of a speckle pattern of circularly polarized light outgoing from a few-mode absorbing optical fiber under the change of sign of the circulation is numerically simulated on the basis of the wave approach. The theoretically predicted parabolic dependence of the value of the angle of rotation of the speckle pattern on the fiber length is discussed. Optical fibers with power-law refractive index profiles are considered.     

Gain-guided soliton in a positive group-dispersion fiber laser

We report on the operation of a passively mode-locked fiber ring laser made of purely normal dispersive fibers. Self-started mode locking can still be achieved in the laser by use of the nonlinear polarization rotation technique, and the mode-locked pulse has large pulse energy, strong frequency chirp, and a mode-locked spectral width limited by the effective laser gain bandwidth. Furthermore, we show that the operation of the laser can be well described by an extended Ginzburg-Landau equation model that governs the soliton dynamics of fiber lasers.