共查询到19条相似文献,搜索用时 60 毫秒
1.
针对AISI 4340合金结构钢难加工的特点,选用PVD硬质合金涂层刀具进行高速干铣削试验,选用扫描电子显微镜(SEM)观察失效刀具表面的磨损形貌特征,选用能谱分析仪(EDS)分析磨损刀具表面的元素分布及含量,揭示刀具的磨损机理。研究结果表明:刀具寿命与切削参数选取有关,随着切削速度的增加,刀具磨损加快,刀具寿命降低。硬质合金涂层刀具的主要磨损形式是前刀面磨损和后刀面磨损,前刀面磨损机理主要是粘结磨损、涂层剥落、切削刃微崩刃;后刀面磨损机理主要是磨粒磨损、粘结磨损、扩散磨损、微裂纹。 相似文献
2.
3.
4.
5.
研究两种自主研制的新型ZTA(Al2O3/Zr O2)陶瓷刀具切削淬硬T10A时的切削性能。刀具后刀面磨损量随切削深度和切削速度的增加而增大;刀具的主要磨损形态为后刀面磨损;主要磨损机理为后刀面磨粒磨损和部分粘结磨损。 相似文献
6.
7.
利用涂层硬质合金刀具对Inconel 718进行了高速干切削试验,采用扫描电子显微镜SEM和能量分散光谱EDS扫描,对不同切削参数下刀具的损坏形态和损坏机理进行了研究。分析结果表明刀具损坏形式主要有前刀面磨损、后刀面磨损、剥落和崩刃。刀具损坏机理主要是粘结磨损、磨粒磨损、氧化磨损和扩散磨损等。 相似文献
8.
采用TiCN/Al_2O_3涂层球头铣刀对天然理石进行高效铣削试验,利用扫描电子显微镜(SEM)观察涂层刀具的表面磨损形貌并基于能谱检测(EDS)分析刀具表面元素组成,并探讨刀具的磨损机制。研究结果表明,刀具磨损包括黏结磨损、磨粒磨损、氧化磨损和疲劳磨损;涂层刀具开始切削时,刀具后刀面出现粘结物和擦伤,在断续切削冲击的作用下造成后刀具材料的剥落;切削线速度较低时,切削系统振动增强,疲劳裂纹在基体内部的扩展降低了刀具基体强度,极易导致较大面积凿削式磨粒磨损,当切削线速度增大时,稳定阶段的磨损形式由凿削式磨粒磨损转变为擦伤式磨粒磨损,刀具磨损减轻;微振磨损的综合作用加剧了涂层刀具磨损,破坏涂层刀具的切削性能。 相似文献
9.
10.
涂层Si_3N_4陶瓷刀具切削性能研究 总被引:1,自引:0,他引:1
研究了不同切削参数对TiN+Al2O3涂层氮化硅陶瓷刀具切削灰铸铁的切削性能的影响,使用工具显微镜、SEM/EDS手段分析了涂层氮化硅刀具的磨损机理,实验还采用相同基体氮化硅陶瓷刀具做了对比分析。研究结果显示TiN+Al2O3涂层氮化硅刀具可以承受比较大的切削用量,对提高加工效率有重大意义;还发现涂层氮化硅陶瓷刀具主要失效形式为磨粒磨损,粘结磨损,在较高切削速度条件下前刀面还会出现因化学磨损形成的月牙洼。 相似文献
11.
Wear behavior and mechanisms of alumina-based ceramic tools in machining of ferrous and non-ferrous alloys 总被引:1,自引:0,他引:1
In this paper, the machining performance and wear mechanisms of two alumina-based ceramic cutting tools (Al2O3/TiB2 and Al2O3/TiB2/SiCw) in continuous turning of hardened steel and nickel based alloy (Inconel 718) were examined. Results showed that in turning of hardened steel performed under identical conditions, Al2O3/TiB2/SiCw tool exhibited lower flank wear resistance than that of Al2O3/TiB2 tool, the mechanisms responsible for this were determined to be the strong atom bonding between SiC and Fe, and the whisker pullout from the matrix for Al2O3/TiB2/SiCw ceramic tool. In continuous turning of Inconel 718, the Al2O3/TiB2/SiCw tool showed greatly improved flank wear resistance compared to Al2O3/TiB2 tool, adhesion and abrasion wear were found to be the dominant wear mechanisms, the adhesion and diffusion of Ni, and Cr of Inconel 718 to the tool rake face may accelerate the tool wear rates. 相似文献
12.
13.
本文对Al2O3/TiC陶瓷刀具材料切削加工G4335V高强钢时的切削性能和耐磨性进行了试验研究。结果表明:在低速切削条件下,Al2O3/TiC陶瓷刀具和硬质合金刀具(YT15)的抗后面磨损能力相差不大,而在高速切削条件下,前者的抗后面磨损能力远高于后者。Al2O3/TiC陶瓷刀具前面的磨损形式主要为粘结磨损,后面的磨损形式主要为磨粒磨损。 相似文献
14.
对TiB2颗粒增强Al2O3刀具在车削正火态、调质态45#钢和球墨铸铁齿轮坯时的刀具磨损性能、磨损机理进行了研究,并与硬质合金刀具的耐磨性能进行了对比。结果表明:Al2O3┐TiB2陶瓷刀具具有良好的耐磨性能。刀具磨损主要以脆性剥离为主,同时存在着犁耕和塑性流变过程,陶瓷刀具表面形成的粘结层结构疏松,与基体结合力较弱,较易脱落,不易形成粘结磨损。 相似文献
15.
T.H.C. Childs 《Tribology International》1983,16(2):67-84
Friction cutting of metals was first reported almost 160 years ago. This review concentrates on its latest development, the slitting of nickel-chromium, titanium and ferrous alloys by toothless, water-cooled, mild steel discs spinning with a rim speed between 50 and 100 ms−1. Slits an thin an 0.25 mm can be produced with little surface damage.Slitting occurs by adhesive wear. When oxidation leading to a mild wear state can be prevented, area slitting rates greater than 10 mm2 s−1 can be achieved: this is the case with nickel-chromium and titanium alloys and with soft or hardened stainless and tool steels. Oxidation cannot be prevented with carbon steels and most cast irons, so these metals cannot in general be slit usefully by fine friction cutting 相似文献
16.
17.
18.
19.
金属切削刀具磨损的监控和预报研究 总被引:3,自引:0,他引:3
介绍一种采用光电法直接测量刀具磨损值,用GMDH方法进行磨损规律的数学建模和寿命预报的方法,实验证明,该系统92%的预防误差小于7.2%,使刀具使用寿命提高43%以上。 相似文献