多循环CCRs法在分离燃煤锅炉尾部烟气中CO2方面的应用

随着温室效应和全球变暖的加剧，煤燃烧所排出的CO2作为引起温室效应的主要气体而引起人们的密切关注。由于燃煤锅炉所排放的尾气中所含的CO2的体积份额低、排放量大，而且处于微负压状态，因此目前控制和分离吸收CO2的方法，包括各类吸收法、吸附法、膜分离法和O2／CO2燃烧技术等，能够经济可行地适用于电力工业燃煤锅炉尾部烟气中CO2分离的方法非常少。与上述各类方法相比，钙基吸收剂CCRs（calcination／carbonation reactions）法是一种新兴的经济可行的分离燃煤锅炉尾部烟气中CO2的方法。对采用该法时，吸收剂的选择、吸收剂在多次CCRs过程中结构特点的变化、提高吸收剂对CO2的吸收容量以及防止吸收剂反应性的衰减等方面进行了详细的阐述。     

N-甲基二乙醇胺/哌嗪/羟乙基乙二胺三元复合溶液捕集烟气中CO2中试研究

化学吸收法是目前烟气回收CO2技术的研究热点,其中一类重要的吸收剂就是醇胺复合溶液.醇胺复合溶液具有对CO2吸收速率快、吸收容量大及再生简单的特点,成为烟气CO2吸收剂的首选.采用中试连续实验装置,以N-甲基二乙醇胺(MDEA)/哌嗪(PZ)/羟乙基乙二胺(AEEA)(摩尔比为0.70:0.15:0.15)三元复合溶液为吸收剂对烟气中CO2进行吸收处理.研究结果表明,吸收剂最佳摩尔浓度为3.0 mol/L,最佳吸收温度为40℃,最佳液气比为10 L/m3;再沸器的热负荷随着吸收温度、吸收剂浓度以及液气比的增加而增大,脱碳率随着入口烟气中CO2浓度的增加而降低.     

CO2捕集回收技术研究

主要介绍了常用的胺化合物吸收法、钙基吸收剂法、金属氧化物法等CO2捕集回收技术的最新研究进展及存在的问题,综合对比了各种方法的优缺点:胺化合物吸收法吸收速率快,但再生能耗较高,因此开发"高效低耗"的复合吸收剂成为研究的重点;钙基吸收剂法在高温环境下对CO2的吸收有较好的效果,但吸收剂的碳酸化转化率及热稳定性是有待解决的关键问题;金属氧化物法具有高的CO2吸收效率,但成本较高.在此基础上,探索了CO2捕集回收技术改进工艺,提出改善吸收剂性能、开发高效低耗的CO2选择性吸收剂将成为今后CO2捕集回收技术的研究方向.     

NaClO2/NaClO复合吸收液同时脱硫脱硝

针对NaClO2氧化吸收法脱硫脱硝成本过高,难以实现工业化的现状,提出了以NaClO2/NaClO为复合吸收剂的同时脱硫脱硝新方法,比单独NaClO2方法效率高,成本低。考虑实际工况条件,给定SO2与NO的初始浓度分别为2 850 mg/m3和670 mg/m3。结果表明,吸收液初始pH为6.0,液气比L/G为20 L/m3,反应温度为55℃时,平均脱硫脱硝效率分别可达99.8%和94.0%。在此基础上对反应机理进行了分析,总结出实验反应主反应方程式。该方法设备简约,操作简单,容易实现全自动控制,综合成本可以接受,比较适合中小型燃煤锅炉的烟气污染治理。     

膜气体吸收技术分离VOCs/N2混合气性能的研究

以C6H6/N2混合气为代表,疏水性聚丙烯中空纤维膜为气液接触膜,n-甲酰吗啉(NFM,n-formyl morpholine)水溶液为吸收剂,研究了膜气体吸收法分离 VOCs/N2 混合气性能.考察了吸收剂流量、吸收剂体积分数、进口气流量、进口气浓度和膜组件结构等诸因素对分离性能的影响.结果表明,在吸收剂流量为 20～100 mL/min,进口气流量为 40～300 mL/min,进口气浓度为 10.2 ms/L的条件下,苯的去除率为 65.0%～99.6%,总体积传质系数为 0.0157～0.08412 s-1.实验证明,采用疏水性多孔膜气体吸收法,NFM 水溶液吸收分离 VOCs/N2 混合气具有较高的分离效率和较快的传质速率.     

氧化镁湿法烟气脱硫回收工艺的技术经济可行性初步分析

介绍了回收结晶硫酸镁的氧化镁湿法烟气脱硫工艺的基本工艺流程,在抛弃法脱硫系统上所作的工业试验证明了吸收液循环提浓MgSO4的可行性.参照工业硫酸镁生产工艺对130t/h燃煤锅炉烟气脱硫作了回收工艺的投资效益分析和整体工艺的经济性评价,结果表明回收工业硫酸镁具有良好的经济效益.     

湿式旋流脱硫除尘一体化装置在燃煤锅炉烟气净化上的应用

某中药厂4 t/h燃煤锅炉烟气采用湿式旋流脱硫除尘一体化装置取得了良好的效果,经实际运行测定除尘率达95%,脱硫率达77%,排出的烟气均能达到排放标准.该净化装置具有旋风水膜除尘器和湿式旋流板洗涤器的双重功能,通过介绍该一体化装置的机理、设计参数和技术经济分析,为燃煤锅炉烟气的脱硫除尘提供参考.     

烟道喷射石灰(石)烟气脱硫技术综述

本文介绍了近几年发展起来的一种简单、中效、适合燃烧中低硫煤的工业锅炉的烟气脱硫技术———烟道喷射石灰 (石 )烟气脱硫技术。从湿法、干法、半干法 3种工艺对烟道喷射烟气脱硫进行了介绍 ,并提出新型脱硫吸收剂是提高烟道脱硫效率的可行方法。最后指出烟道脱硫今后的研究方向     

燃煤锅炉烟气NOx污染等离子体治理技术

燃煤锅炉烟气NOx污染治理技术种类较多.本文综合评述了各种烟气NOx污染等离子体治理技术,重点介绍了电晕放电脱除烟气中NOx的最新研究成果.对燃煤锅炉烟气NOx污染治理技术的研究和开发具有实用价值.     

燃煤锅炉脱汞技术研究进展

燃煤锅炉是主要的烟气汞排放源,汞大多存在于亚微米级颗粒中,其对环境和人类造成的影响不容忽视。综述了现阶段燃煤锅炉汞排放控制技术的研究进展,并对各项技术的脱汞效率、影响因素、投资成本、优缺点及应用可行性进行了分析比较。分析表明,利用现有污染物控制设备(除尘装置、脱硝装置、脱硫装置)协同脱汞比较经济有效,也是当前研究的重点;洗煤技术、燃烧方式的改进和添加燃烧附加物可作为辅助措施使用。     

Sorption of Zn(II) in aqueous solutions by scoria

We conducted kinetic and equilibrium sorption experiments on removal of Zn(II) from aqueous solutions by scoria (a vesicular pyroclastic rock with basaltic composition) from Jeju Island, Korea, in order to examine its potential use as an efficient sorbent. The batch-type kinetic sorption tests under variable conditions indicated that the percentage of Zn(II) removal by scoria increases with decreasing initial Zn(II) concentration, particle size, and sorbate/sorbent ratio. However, the sorption capacity decreases with the decrease of the initial Zn(II) concentration and sorbate/sorbent ratio. Equilibrium sorption tests show that Jeju scoria has a larger capacity and affinity for Zn(II) sorption than commercial powdered activated carbon (PAC); at initial Zn(II) concentrations of more than 10mM, the sorption capacity of Jeju scoria is about 1.5 times higher than that of PAC. The acquired sorption data are better fitted to the Langmuir isotherm than the Freundlich isotherm. Careful examination of ionic concentrations in sorption batches suggests that the sorption behavior is mainly controlled by cation exchange and typically displays characteristics of 'cation sorption'. The Zn(II) removal capacity decreases when solution pH decreases because of the competition with hydrogen ions for sorption sites, while the Zn(II) removal capacity increases under higher pH conditions, likely due to hydroxide precipitation. At an initial Zn(II) concentration of 5.0mM, the removal increases from 70% to 96% with the increase of initial pH from 3.0 to 7.0. We recommend Jeju scoria as an economic and efficient sorbent for Zn(II) in contaminated water.     

Removal of lignin and tannin colour from aqueous solution by adsorption onto activated charcoal

Sorptive uptake of lignin and tannin from an aqueous phase by activated charcoal was investigated in the laboratory. The sorption reaction was found to be of a first order. The influence on the rate of sorption of various factors, such as amount of sorbent and pH of the system, have been investigated. Sorption data fit well into the Langmuir adsorption isotherm, indicating formation of a monolayer over a homogeneous sorbent surface. Sorption capacity, rate constant, intraparticle diffusion coefficient, etc. were calculated from the sorption data. Desorption studies indicate the irreversible nature of the sorption reaction, whereas interruption studies suggest film diffusion to be rate limiting.     

湿法再生吸附剂制备及用于大气CO2的直接捕集

基于湿法再生吸附技术,利用强碱性季铵盐树脂材料制备了异相吸附剂薄膜,应用于大气中极低CO2的直接分离,以对抗全球变暖。通过滴定法分析吸附剂材料的电荷密度和吸附容量,利用SEM分析不同工况下制备出来的膜材料的表观结构,并对膜材料进行CO2吸附性能的测试。结果发现,热处理能够明显提高膜材料的吸附性能,还研究吸附剂制备对吸附速率,吸附量和机械强度等性能的影响,发现粒径小于43μm的树脂粉末,按60％质量分数制成的500μm厚膜材料具有较优的综合性能。     

Efficiency of recycled wool-based nonwoven material for the removal of oils from water

The aim of this study was to highlight the potential use of recycled wool-based nonwoven material for the removal of diesel fuel, crude, base, vegetable and motor oil from water. Sorption capacity of the material in water and in oil without water, oil retention, sorbent reusability and buoyancy in static and dynamic conditions were investigated. The results show high sorption capacity of recycled wool for different kinds of oil. This sorbent also exhibited excellent buoyancy after 24h of sorption as well as a good reusability since the decrease in sorption capacity did not exceed 50% of the initial value after five sorption cycles in oil without water.     

Characterization of carbons from olive cake by sorption of wastewater pollutants

Studies has been conducted to compare the sorption properties between raw carbons made from olive cake and commercial activated carbons to remove aquatic pollutant such as heavy metal (HM), phenol (Ph), dodecylbenzenesulfonic acid-sodium salt detergent (DBSNa) and methylene blue dye (MB). Effect of acidic treatments by H2SO4, HCl and HNO3 on the sorption properties of olive cake carbon (OCC) were studied by mass titration, SEM photographs, sorption isotherms. It is found that acidic treatment changes the surface properties of OCC but do not enhance its sorption capacity. Compared to commercial activated carbons the OCC derivatives generally are equally able to uptake HM and Ph from solution but MB and DBSNa are not. This different behaviour is to attribute to manufacturing and activation treatments so as surface groups of the precursor sorbent material. For the heavy metals, chromium and silver were removed effectively but to small extent cadmium. This may be because of the various charge densities of metal elements tested. The results of the multiple experiments indicate that sorption of cadmium ions can be significantly improved by the presence of complexing agents sorbed from the carbon. An empirical mathematical form is proposed to correlate experimental data and to compare the performance of the different sorbent materials.     

2种典型餐厨垃圾资源化处理工艺的环境影响分析

为了评估餐厨垃圾资源化处理工艺对环境的影响,运用生命周期评价的方法,比较了2种典型的资源化处理工艺——好氧堆肥和湿热处理对环境的影响。结果表明,2种餐厨垃圾资源化处理工艺对全球变暖、生态毒性、酸化和富营养化的影响各有不同。其中,好氧堆肥对全球变暖的贡献较大,碳排放为337.7 kg CO_2eq./t。湿热处理为163.1 kg CO_2eq./t。在环境影响负荷方面,湿热处理工艺中的高能耗加重了毒性的影响。但由于其对环境的酸化、富营养化的不利影响较小,湿热处理的环境影响负荷总值是好氧堆肥的62.5%。总体上,湿热处理是一种对环境影响较小的餐厨垃圾处理工艺。     

Equilibrium and kinetic modelling of chromium(III) sorption by animal bones

The paper discusses sorption of Cr(III) ions from aqueous solutions by animal bones. Animal bones were found to be an efficient sorbent with the maximum experimentally determined sorption capacity in the range 29-194 mg g(-1) that depended on pH and temperature. The maximum experimentally determined sorption capacity was obtained at 50 degrees C, pH 5. Batch kinetics and equilibrium experiments were performed in order to investigate the influence of contact time, initial concentration of sorbate and sorbent, temperature and pH. It was found that sorption capacity increased with increase of Cr(III) concentration, temperature and initial pH of metal solution. Mathematical models describing kinetics and statics of sorption were proposed. It was found that process kinetics followed the pseudo-second-order pattern. The influence of sorbent concentration was described with Langmuir-type equation and the influence of sorbate concentration was described with empirical dependence. The models were positively verified.     

Potential of biological materials for removing heavy metals from wastewater

Agricultural products/by-products are natural sorbent materials that possess capacity for removing contaminants including heavy metals from wastewaters and hence can be exploited as replacement of costly methods for wastewater treatment. The sorption of heavy metals onto these biomaterials is attributed to constituent's proteins, carbohydrates, and phenolic compounds that contain functional groups such as carboxylate, hydroxyl, and amine. Natural efficiency of these materials for removing heavy metals can be enhanced by treating them with chemicals. The present review emphasizes their use in developing eco-friendly technology for a large-scale treatment of wastewater.     

Influence of the operation conditions on CO2 capture by CaO-derived sorbents prepared from synthetic CaCO3

In this work, a statistical experimental design is performed in order to prepare CaCO₃ materials for use as CaO-based CO₂ sorbent precursors. The influence of different operational parameters such as synthesis temperature (ST), stirring rate (SR) and surfactant percent (SP) on CO₂ capture is studied by applying Response Surface Methodology (RSM). The samples were characterized using different analytical techniques including X-ray diffraction, N₂ adsorption isotherm analysis and Scanning Electron Microscopy–X-ray Energy Dispersive Spectroscopy (SEM-EDX). CO₂ capture capacity was determined by means of a thermogravimetric analyzer which recorded the mass uptake of the samples when these were exposed to a gas stream containing diluted (15%) CO₂. The statistical approach used in this work provides a rapid way of predicting and optimizing the main preparation variables of CaO-derived sorbents for CO₂ sorption. The results obtained clearly indicate that four parameters statistically influence CO₂ uptake: SR, the square of SR, its interaction with SP and the square of SP.     

Performance of Copper Chloride-Impregnated Sorbents on Mercury Vapor Control in an Entrained-Flow Reactor System

Abstract

An entrained-flow system has been designed and constructed to simulate in-flight mercury (Hg) capture by sorbent injection in ducts of coal-fired utility plants. The test conditions of 1.2-sec residence time, 140 °C gas temperature, 6.7 m/sec (22 ft/sec) gas velocity, and 0–0.24 g/m³ (0–15 lbs of sorbent per 1 million actual cubic feet of flue gas [lb/MMacf]) sorbent injection rates were chosen to simulate conditions in the ducts. Four kinds of sorbents were used in this study. Darco Hg-LH served as a benchmark sorbent with which Hg control capability of other sorbents could be compared. Also, Darco-FGD was used as a representative raw activated carbon sorbent. Two different copper chloride-impregnated sorbents were developed in our laboratory and tested in the entrained-flow system to examine the possibility of using these sorbents at coal-fired power plants. The test results showed that one of the copper chloride sorbents has remarkable elemental mercury (Hg⁰) oxidation capability, and the other sorbent demonstrated a better performance in Hg removal than Darco Hg-LH.