The selective reduction of NOx with propene on Pt-beta catalyst: A transient study

The mechanism of the NO/C₃H₆/O₂ reaction has been studied on a Pt-beta catalyst using transient analysis techniques. This work has been designed to provide answers to the volcano-type activity behaviour of the catalytic system, for that reason, steady state transient switch (C₃H₆/NO/O₂ → C₃H₆/Ar/O₂, C₃H₆/Ar/O₂ → C₃H₆/NO/O₂, C₃H₆/NO/O₂ → Ar/NO/O₂, Ar/NO/O₂ → C₃H₆/NO/O₂, C₃H₆/NO/O₂ → C₃H₆/NO/Ar and C₃H₆/NO/Ar → C₃H₆/NO/O₂) and thermal programmed desorption (TPD) experiments were conducted below and above the temperature of the maximum activity (T_max). Below T_max, at 200 °C, a high proportion of adsorbed hydrocarbon exists on the catalyst surface. There exists a direct competition between NO and O₂ for Pt free sites which is very much in favour of NO, and therefore, NO reduction selectively takes place over hydrocarbon combustion. NO and C₃H₆ are involved in the generation of partially oxidised hydrocarbon species. O₂ is essential for the oxidation of these intermediates closing the catalytic cycle. NO₂ is not observed in the gas phase. Above T_max, at 230 °C, C₃H_6 ads coverage is negligible and the surface is mainly covered by O_ads produced by the dissociative adsorption of O₂. NO₂ is observed in gas phase and carbon deposits are formed at the catalyst surface. From these results, the state of Pt-beta catalyst at T_max is inferred. The reaction proceeds through the formation of partially oxidised active intermediates (C_xH_yO_zN_w) from C₃H_6 ads and NO_ads. The combustion of the intermediates with O₂(g) frees the Pt active sites so the reaction can continue. Temperature has a positive effect on the surface reaction producing active intermediates. On the contrary, formation of NO_ads and C₃H_6 ads are not favoured by an increase in temperature. Temperature has also a positive effect on the dissociation of O₂ to form O_ads, consequently, the formation of NO₂ is favoured by temperature through the oxygen dissociation. NO₂ is very reactive and produces the propene combustion without NO reduction. These facts will determine the maximum concentration of active intermediates and consequently the maximum of activity.     

Catalytic oxidation of HCN over a 0.5% Pt/Al2O3 catalyst

The adsorption of HCN on, its catalytic oxidation with 6% O₂ over 0.5% Pt/Al₂O₃, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N₂O, NO and NO₂, and some residual adsorbed N-containing species were oxidized to NO and NO₂ during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N₂ and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N₂O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO_x in the products. The co-feeding of H₂O and C₃H₆ had little, if any effect on the total HCN conversion, but C₃H₆ addition did increase the conversion to NO and decrease the conversion to NO₂, perhaps due to the competing presence of adsorbed fragments of reductive C₃H₆. Evidence is also presented that introduction of NO and NO₂ into the reactant gas mixture resulted in additional reaction pathways between these NO_x species and HCN that provide for lean-NO_x reduction coincident with HCN oxidation.     

Water vapor sensitivity of nanosized La(Co, Mn, Fe)1−x(Cu, Pd)xO3 perovskites during NO reduction by C3H6 in the presence of oxygen

A series of La(Co, Mn, Fe)_1−x(Cu, Pd)_xO₃ perovskites having high specific surface areas and nanosized crystal domains was prepared by reactive grinding. The solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed desorption (TPD) of O₂, NO + O₂, C₃H₆, in the absence or presence of 5% H₂O, Fourier transform infrared (FTIR) spectroscopy, as well as activity tests towards NO reduction by propene under the conditions of 3000 ppm NO, 3000 ppm C₃H₆, 1% O₂, 0 or 10% H₂O, and 50,000 h⁻¹ space velocity. The objective was to investigate the influence of H₂O addition on catalytic behavior. A good performance (100% NO conversion, 77% N₂ yield, and 90% C₃H₆ conversion) was achieved at 600 °C over LaFe_0.8Cu_0.2O₃ under a dry feed stream. With the exposure of LaFe_0.8Cu_0.2O₃ to a humid atmosphere containing 10% water vapor, the catalytic activity was slightly decreased yielding 91% NO conversion, 51% N₂ yield, and 86% C₃H₆ conversion. A competitive adsorption between H₂O vapor with O₂ and NO molecules at anion vacancies over LaFe_0.8Cu_0.2O₃ was found by means of TPD studies here. A deactivation mechanism was therefore proposed involving the occupation of available active sites by water vapor, resulting in an inhibition of catalytic activity in C₃H₆ + NO + O₂ reaction. This H₂O deactivation was also verified to be strictly reversible by removing steam from the feed.     

C2H6/C3H8影响CH4爆炸极限参数及动力学特性研究

为研究C₂H₆/C₃H₈对甲烷爆炸极限参数及动力学特性的影响,采用标准的可燃气体爆炸极限测定装置测定了不同配比的C₂H₆/C₃H₈混合气体对甲烷爆炸极限的影响规律,同时得出了氮气惰化条件下甲烷爆炸临界参数的变化规律。此外,利用Chemkin软件模拟了C₂H₆/C₃H₈混合气体对甲烷爆炸过程中中间产物浓度的影响情况,并进行了敏感性分析。结果表明,C₂H₆/C₃H₈的存在降低了甲烷的爆炸上下限,增大了甲烷的爆炸危险度;在氮气惰化过程中甲烷的爆炸上限下降,爆炸下限上升,最终爆炸上下限重合,重合点处甲烷浓度和氮气临界浓度均随C₂H₆/C₃H₈的添加而逐渐减小;此外,C₂H₆/C₃H₈混合气体使甲烷爆炸过程中CO和·H的生成量逐渐增大,而CO₂、·O和·OH的生成量则有下降趋势,通过对爆炸过程中甲烷体积的敏感性分析,发现C₂H₆/C₃H₈的存在在某种程度上促进了甲烷爆炸。对比不同配比的C₂H₆/C₃H₈混合气体,发现C₃H₈含量越高,其对甲烷爆炸过程中相关参数的影响越大,这可为工矿企业的安全生产提供一定的理论依据。     

On the promotional effect of Pd on the propene-assisted decomposition of NO on chlorinated Ce0.68Zr0.32O2

The selective catalytic reduction (SCR) of NO_x assisted by propene is investigated on Pd/Ce_0.68Zr_0.32O₂ catalysts (Pd/CZ), and is compared, under identical experimental conditions, with that found on a Pd/SiO₂ reference catalyst. Physico-chemical characterisation of the studied catalysts along with their catalytic properties indicate that Pd is not fully reduced to metallic Pd for the Pd/CZ catalysts. This study shows that the incorporation of Pd to CZ greatly promotes the reduction of NO in the presence of C₃H₆. These catalysts display very stable deNO_x activity even in the presence of 1.7% water, the addition of which induces a reversible deactivation of about 10%. The much higher N₂ selectivity obtained on Pd/CZ suggests that the lean deNO_x mechanism occurring on these catalysts is different from that occurring on Pd⁰/SiO₂. A detailed mechanism is proposed for which CZ achieves both NO oxidation to NO₂ and NO decomposition to N₂, whereas PdO_x activates C₃H₆ via ad-NO₂ species, intermediately producing R-NO_x compounds that further decompose to NO and C_xH_yO_z. The role of the latter oxygenates is to reduce CZ to provide the catalytic sites responsible for NO decomposition. The proposed C₃H₆-assisted NO decomposition mechanism stresses the key role of NO₂, R-NO_x and C_xH_yO_z as intermediates of the SCR of NO_x by hydrocarbons.     

Catalytic properties of novel La–Sr–Cu–O–S perovskites for automotive C3H6/CO oxidation in the presence of SOx

A La–Sr–Cu–O–S system with K₂NiF₄ perovskite-type structure has been studied as a novel SO_x-resistant combustion catalyst. The XRD result implied that sulfur is incorporated into the structure as non-sulfate-type cations. An introduction of sulfur with highly positive valence (S⁶⁺ or S⁴⁺) into the lattice requires the charge compensation by decreasing the oxidation number of Cu. This is accompanied by the creation of more reducible Cu species, which would achieve the light-off of catalytic C₃H₆ oxidation at lower temperatures. More important feature of sulfur-containing compounds is that the catalytic C₃H₆ oxidation was significantly accelerated by addition of SO₂ to the gas feed. The catalytic performance for the oxidation of C₃H₆ and CO and the reduction of NO was finally evaluated in a simulated automotive exhaust in the presence of SO₂.     

Uncharged atomic oxygen in oxidative conversion of C1-C2 alkanes

The role of uncharged atomic oxygen species in oxidative conversion of CH₄ and C₂H₆ has been considered. It is shown that active atomic oxygen species participate in C₁---C₂alkanes conversion in the presence of NO on zeolites, in the CH₄N₂O¹ and CH₄---O₂ systems on transition metal silicides and nitrides, as well as hydrocarbon oxidation during N₂O and O₃ photolysis by excimer laser light. Participation of uncharged oxygen species in conversion of light alkanes makes it possible to explain not only hydrocarbon formation pathways, but those of oxygen-containing compounds as well.     

Free-radical reactions involved in C1-C3 hydrocarbons interaction with oxide catalysts

Experimental proofs of a free radical mechanism in methane oxidative coupling, with homolytic rupture of the C---H bond are given. High concentrations of free radical sites are produced by mechanical milling of SiO₂. A study of C₁---C₃alkanes interaction with these sites allows to simulate the, processes of alkanes oxidation and oxidative dehydrogenation. The reactivity of ethane and propane is higher than that of methane in accordance with the Polanyi-Semenov rule. Oxidative dehydrogenation of ethane is studied on Cd-containing zeolites. CH₄, C₂H₆ and C₃H₈ oxidative dehydrogenation by O₂ or CO₂ is studied on a MNO/SiO₂ catalyst. The initiation of radical reactions of hydrocarbons on Cl-containing catalysts proceeds via chlorine atoms generation.     

The effect of oxygen concentration on the reduction of NO with propylene over CuO/γ-Al2O3

The effect of oxygen concentration on the pulse and steady-state selective catalytic reduction (SCR) of NO with C₃H₆ over CuO/γ-Al₂O₃ has been studied by infrared spectroscopy (IR) coupled with mass spectroscopy studies. IR studies revealed that the pulse SCR occurred via (i) the oxidation of Cu⁰/Cu⁺ to Cu²⁺ by NO and O₂, (ii) the co-adsorption of NO/NO₂/O₂ to produce Cu²⁺(NO₃⁻)₂, and (iii) the reaction of Cu²⁺(NO₃⁻)₂ with C₃H₆ to produce N₂, CO₂, and H₂O. Increasing the O₂/NO ratio from 25.0 to 83.4 promotes the formation of NO₂ from gas phase oxidation of NO, resulting in a reactant mixture of NO/NO₂/O₂. This reactant mixture allows the formation of Cu²⁺(NO₃⁻)₂ and its reaction with the C₃H₆ to occur at a higher rate with a higher selectivity toward N₂ than the low O₂/NO flow. Both the high and low O₂/NO steady-state SCR reactions follow the same pathway, proceeding via adsorbed C₃H₇---NO₂, C₃H₇---ONO, CH₃COO⁻, Cu⁰---CN, and Cu⁺---NCO intermediates toward N₂, CO₂, and H₂O products. High O₂ concentration in the high O₂/NO SCR accelerates both the formation and destruction of adsorbates, resulting in their intensities similar to the low O₂/NO SCR at 523–698 K. High O₂ concentration in the reactant mixture resulted in a higher rate of destruction of the intermediates than low O₂ concentration at temperatures above 723 K.     

Selective catalytic reduction of nitrogen oxide by hydrocarbons over mordenite-type zeolite catalysts

The reduction of NO by hydrocarbons such as C₂H₄, C₂H₆, C₃H₆, and C₃H₈ has been investigated over mordenite-type zeolite catalysts including HM, CuHM, NZA (natural zeolite), and CuNZA prepared by an ion-exchange method in a continuous flow fixed-bed reactor. NO conversion over CuNZA catalyst reaches about 94% with 2000 ppm of C₃H₆ at 500°C. As reductants, alkenes seem to exhibit a higher performance for NO conversion than alkanes regardless of the catalysts. No deterioration of the catalytic activity due to carbonaceous deposits for CuNZA was observed above 400°C even after 30 h of on-stream time, but SO₂ in the feed gas stream causes a severe poisoning of the CuNZA catalyst. The effect of H₂O on NO conversion was significant regardless of the catalysts and the reductants employed in this study. However, CuNZA catalyst shows a unique water tolerance with C₃H₆. The reaction path of NO to N₂ is the most important factor for high performance of this catalytic system. NO is directly reduced by a reaction intermediate, C_n′H_m′(O) formed from hydrocarbon and O₂, N₂O is another reaction intermediate which can be easily removed by C_n′H_m′(O).     

Selective catalytic reduction of NO by C2H2 over MoO3/HZSM-5

Molybdenum impregnated HZSM-5 zeolite catalysts with MoO₃ loading from 1 to 8 wt.% were studied in detail for the selective catalytic reduction (C₂H₂-SCR) of NO by acetylene. A 83.9% of NO could be removed by the reductant at 350 °C under 1600 ppm of NO, 800 ppm of C₂H₂ and 9.95% of O₂ in He over 2%MoO₃/HZSM-5 catalyst with a specific activity of in NO elimination and the competitiveness factor (c.f.) of 33.6% for the reductant. The NO elimination level and the c.f. value were ca. 3–4 times as high as those using methane or propene as reductant over the catalyst in the same reaction condition. About same reaction rate was estimated in NO oxidation as that in the NO reduction over each xMoO₃/HZSM-5 (x = 0–8%) catalyst, which confirms that NO₂ is a crucial intermediate for the aimed reaction over the catalysts. Appropriate amount of Mo incorporation to HZSM-5 considerably enhanced the title reaction, both by accelerating the intermediate formation and by strengthening the adsorption NO_x on the catalyst surface under the reaction conditions. Rather lower adsorption tendency of acetylene compared with propene on the catalysts explains the catalyst's steady performance in the C₂H₂-SCR of NO and rapid deactivation in the C₃H₆-SCR of NO.     

Catalytic reduction of NO by propene over LaCo1−xCuxO3 perovskites synthesized by reactive grinding

One series of LaCo_1−xCu_xO₃ perovskites with high specific surface area was prepared by the new method designated as reactive grinding. These solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), H₂-temperature programmed reduction (TPR), O₂-temperature programmed desorption (TPD), NO + O₂-TPD, C₃H₆-TPD, NO + O₂-temperature programmed surface reaction (TPSR) under C₃H₆/He flow as well as catalytic reduction of NO activity tests. The catalytic performance of unsubstituted sample is poor with a maximum conversion to N₂ of 19% at 500 °C at a space velocity of 55,000 h⁻¹ (3000 ppm NO, 3000 ppm C₃H₆, 1% O₂ in helium) but it is improved by incorporation of Cu into the lattice. A maximal N₂ yield of 46% was observed over LaCo_0.8Cu_0.2O₃ under the same conditions. Not only the abundance of -oxygen but also the mobility of β-oxygen of lanthanum cobaltite was remarkably enhanced by Cu substitution according to O₂-TPD and H₂-TPR studies. The better performance of Cu-substituted samples is likely to correspond to the essential nature of Cu and facility to form nitrate species in NO transformation conditions. In the absence of O₂, the reduction of NO by C₃H₆ was performed over LaCo_0.8Cu_0.2O₃, leading to a maximal conversion to N₂ of 73% accompanied with the appearance of some organo nitrogen compounds (identified as mainly C₃H₇NO₂). Subsequently, a mechanism involving the formation of an organic nitro intermediate, which further converts into N₂, CO₂ and H₂O via isocyanate, was proposed. Gaseous oxygen acts rather as an inhibitor in the reaction of NO and C₃H₆ over highly oxidative LaCo_0.8Cu_0.2O₃ due to the heavily unselective combustion of C₃H₆ by O₂.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Selective catalytic reduction of NOx with propylene in the presence of oxygen over Co–Pt promoted H-MFI and HY

Kinetic and in situ spectroscopic studies of Co–Pt/MFI and Co–Pt/HY catalysts for the selective reduction of NO_x with propylene in the presence of oxygen were carried out. The results of catalytic tests of Co–Pt/MFI showed that the addition of Pt to Co based catalyst improved the activity, but a small increase in selectivity to N₂O (15–20%) was observed. In the case of Co–Pt/HY catalyst, the addition of Pt improved the activity more significantly and however, a larger increase in selectivity to N₂O (6–72%) was obtained. It was also found from the results of FT-IR studies of Co–Pt/MFI that the reduction of NO to N₂ was as follows: firstly the oxidation of NO to NO₂ occurred over metallic Pt and NO₂ forms Co–NO₂, Co–ONO, and/or Co–ONO₂; secondly, the partial oxidation of C₃H₆ was happened over Brønsted acid sites and the reaction of NO₂ formed on Co sites with partial oxidized C₃H₆ produced organo-nitro species. These species were dehydrated and isomerized to form isocyanate. Finally, [NCO] type intermediates react with NO from gas phase to selectively yield N₂.     

Chemical Effects of CO2 Concentration on Soot Formation in Jet-stirred/Plug-flow Reactor

Soot formation was investigated numerically with CO2 addition in a jet-stirred/plug-flow reactor （JSR/PFR） C2H4/OJN2 reactor （C/O ratio of 2.2） at atmospheric pressure. An updated Kazakov mechanism empha- sizes the effect of the O2/CO2 atmosphere instead of an O2/N2 one in the premixed flame. The soot formation was taken into account in the JSR/PFR for C2H4/O2/N2. The effects of CO2 addition on soot formation in different C2H4/O2/CO2/N2 atmospheres were studied, with special emphasis on the chemical effect. The simulation shows that the endothermic reaction CO2 ＋ H - CO ＋ OH is responsible of the reduction of hydrocarbon intermediates in the CO2 added combustion through the supplementary formation of hydroxyl radicals. The competition of CO2 for H radical through the above forward reaction with the single most important chain branching reaction H ＋ O2, ＇ O ＋ OH reduces significantly the fuel burning rate. The chemical effects of CO2 cause a significant increase in residence time and mole fractions of CO and OH, significant decreases in some intermediates （H, C2H2）, polycyclic aromatic hydrocarbons （PAHs, C6H6 and CI6H10, etc.） and soot volume fraction. The CO2 addition will leads to a decrease by only about 5% to 20% of the maximum mole fractions of some C3 to Clo hydrocarbon intermediates. The sensitivity analysis and reaction-path analysis results show that C2H4 reaction path and products are altered due to the CO2 addition.     

不同氧浓度下煤挥发分燃烧的化学动力学研究

燃煤有机污染物对人类健康和生态环境存在严重危害,而O₂对火焰中有机产物的形成具有明显的调控作用。鉴于煤挥发分燃烧是燃煤过程中至关重要的一环,本文以煤热解气为燃料,通过数值模拟研究了氧化剂侧O₂浓度对对冲扩散火焰中碳氢产物生成特性和机制的影响。结果表明,O₂浓度升高促进了O和OH的生成,进而提高H浓度,突显了含H和OH参与的反应的重要性。此外,乙炔(C₂H₂)、丙炔(PC₃H₄)、炔丙基(C₃H₃)、乙烯基乙炔(C₄H₄)、苯(C₆H₆)和萘(C₁₀H₈)的浓度均增大。增加O₂浓度促进了C₂H₂向PC₃H₄的转化,并使得C₃H₃更倾向于转化为丁二烯(C₄H₆),而富烯更倾向于通过苯基(C₆H₅)生成C₆H₆,因此C₆H₅作为C₆H₆前体的地位被加强。     

不同氧浓度下煤挥发分燃烧的化学动力学研究

燃煤有机污染物对人类健康和生态环境存在严重危害,而O₂对火焰中有机产物的形成具有明显的调控作用。鉴于煤挥发分燃烧是燃煤过程中至关重要的一环,本文以煤热解气为燃料,通过数值模拟研究了氧化剂侧O₂浓度对对冲扩散火焰中碳氢产物生成特性和机制的影响。结果表明,O₂浓度升高促进了O和OH的生成,进而提高H浓度,突显了含H和OH参与的反应的重要性。此外,乙炔(C₂H₂)、丙炔(PC₃H₄)、炔丙基(C₃H₃)、乙烯基乙炔(C₄H₄)、苯(C₆H₆)和萘(C₁₀H₈)的浓度均增大。增加O₂浓度促进了C₂H₂向PC₃H₄的转化,并使得C₃H₃更倾向于转化为丁二烯(C₄H₆),而富烯更倾向于通过苯基(C₆H₅)生成C₆H₆,因此C₆H₅作为C₆H₆前体的地位被加强。     

A comparative study of Ag/Al2O3 and Cu/Al2O3 catalysts for the selective catalytic reduction of NO by C3H6

The selective catalytic reduction (SCR) of NO by C₃H₆ in excess oxygen was evaluated and compared over Ag/Al₂O₃ and Cu/Al₂O₃ catalysts. Ag/Al₂O₃ showed a high activity for NO reduction. However, Cu/Al₂O₃ showed a high activity for C₃H₆ oxidation. The partial oxidation of C₃H₆ gave surface enolic species and acetate species on the Ag/Al₂O₃, but only an acetate species was clearly observed on the Cu/Al₂O₃. The enolic species is a more active intermediate towards NO + O₂ to yield—NCO species than the acetate species on the Ag/Al₂O₃ catalyst. The Ag and Cu metal loadings and phase changes on Al₂O₃ support can affect the activity and selectivity of Ag/Al₂O₃ and Cu/Al₂O₃ catalysts, but the formation of enolic species is the main reason why the activity of the Ag/Al₂O₃ catalyst for NO reduction is higher than that of the Cu/Al₂O₃ catalyst.     

The homogeneous gas phase oxidation of methane and the retarding effect of basic/inert surfaces

The homogeneous gas phase O₂-based oxidation of methane was studied in the temperature range, from 500°C to 750°C at methane partial pressures ranging from 3 bar to 40 bar. At the lower end of the temperature range methanol, formaldehyde, and CO represent the main products, while at temperatures exceeding 650° C/C-coupled products, C₂H₆, C₂H₄, C₃H₆ and C₃H₈ predominate. The change in selectivity as function of the temperature is well explained based on a free radical chain mechanism with degenerate branching, initiated by the gas phase reaction, CH₄+O₂→CH^·₃+HO^·₂. Bringing in basic catalysts known to catalyze the system at low methane partial pressures, in the reactor e.g. SrCO₃, BaCO₃, and 7% Li/MgO resulted in reduced rates of methane and oxygen conversions, and only minor changes in the selectivity to coupled products were observed.     

The catalytic activity of FeOx/ZrO2 for the abatement of NO with propene in the presence of O2

FeO_x/ZrO₂ samples, prepared by impregnation with Fe(NO₃)₃, were characterised by means of DRS, XRD, FTIR, redox cycles and volumetric CO adsorption. Volumetric CO adsorption, combined with FTIR, showed that 45% of iron in the sample containing 2.8 Fe atoms nm⁻² was capable of forming iron carbonyls. DRS evidenced Fe₂O₃ on samples with Fe-content≥2.8 atoms nm⁻². The selective catalytic reduction of NO with C₃H₆ in the presence of O₂ was studied with a reactant mixture containing NO=4000 ppm, C₃H₆=4000 ppm, O₂=2%. The dependence on iron-content suggests that only isolated iron, prevailing in dilute FeO_x/ZrO₂, is active for NO reduction, whereas iron on the surface of small oxide particles, prevailing in concentrated FeO_x/ZrO₂, is active for C₃H₆ combustion.