Poly[ethylene‐co‐(vinyl alcohol)]‐graft‐poly(ε‐caprolactone) Synthesis by Reactive Extrusion, 1 ‐ Structural and Kinetic Study

Chemical modification of EVOH in the molten state at 185 °C by a grafting from process of poly(ε‐caprolactone) in batch was studied. ¹H NMR was used to characterize the structure evolutions of PCL grafts. In addition to grafting reactions, dynamic covalent transesterification reactions between EVOH residual alcohols and the polyester grafts led to a redistribution of the PCL grafts length. up to 27 and SR up to 80% were obtained. Experiments made in a corotating mini twin‐screw extruder also confirmed these results. The effect of the alcohol to caprolactone ratio and catalyst concentration (SnOct₂) on kinetic evolution showed that few minutes were necessary to complete the polymerization. A kinetic model was proposed and adequate conditions for the synthesis by reactive extrusion were defined.

     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure and Mechanical Properties of Poly(lactic acid) Filled with (Starch nanocrystal)‐graft‐poly(ε‐caprolactone)

Poly(ε‐caprolactone) (PCL) was grafted to the surface of starch nanocrystals (StN) via microwave‐assisted ROP. The resultant nanoparticles were then incorporated into a poly(lactic acid) matrix to produce fully‐biodegradable nanocomposites with good mechanical properties. A loading level of 5 wt.‐% StN‐g‐PCL resulted in simultaneous enhancements of strength and elongation. The StN‐g‐PCL self‐aggregated as rubbery microparticles to enhance the elongation by ca. 10‐fold over that of neat PLA. Meanwhile, the grafted PCL chains were miscible with PLA and formed a stress‐transferring interface to the StN, providing a reinforcing function.

     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Transesterification in homogeneous poly(ε‐caprolactone)–epoxy blends

Transesterification has been investigated in poly(ε‐caprolactone) (PCL)–epoxy blends. In the hot melt process, the hydroxyl on diglycidyl ether of bisphenol‐A (DGEBA) monomers is too low to give a noticeable transesterification reaction. In the postcure process, model reactions reveal that the hydroxyls from a ring‐opening reaction are able to react with the esters of PCL. In the meantime, the PCL molecular weight decrease and its distribution becomes broader. Nuclear magnetic resonance spectra reveal that fraction of the tertiary hydroxyls converts to secondary hydroxyls. In the cured DGEBA–3,3′‐dimethylmethylene‐di(cyclohexylamine)–PCL blend, a homogeneous morphology is achieved. PCL segments are grafted onto the epoxy network after postcuring and result in the lower T_g observed in the differential scanning calorimetry thermogram. A higher transesterification extent also results in broader transition peaks by dynamic mechanical analysis. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 75–82, 1999     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers by combined ring‐opening polymerization and cross‐coupling processes

2,5‐Dibromo‐1,4‐(dihydroxymethyl)benzene was used as initiator in ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate (Sn(Oct)₂) catalyst. The resulting poly(ε‐caprolactone) (PCL) macromonomer, with a central 2,5‐dibromo‐1,4‐diphenylene group, was used in combination with 1,4‐dibromo‐2,5‐dimethylbenzene for a Suzuki coupling in the presence of Pd(PPh₃)₄ as catalyst or using the system NiCl₂/bpy/PPh₃/Zn for a Yamamoto‐type polymerization. The poly(p‐phenylenes) (PPP) obtained, with PCL side chains, have solubility properties similar to those of the starting macromonomer, ie soluble in common organic solvents at room temperature. The new polymers were characterized by ¹H and ¹³C NMR and UV spectroscopy and also by GPC measurements. The thermal behaviour of the precursor PCL macromonomer and the final poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers were investigated by thermogravimetric analysis and differential scanning calorimetry analyses and compared. Copyright © 2004 Society of Chemical Industry     

Preparation and characterization of electrospun poly(ε‐caprolactone)–pluronic–poly(ε‐caprolactone)‐based polyurethane nanofibers

In this study, amphiphilic poly(ε‐caprolactone)–pluronic–poly(ε‐caprolactone) (PCL–pluronic–PCL, PCFC) copolymers were synthesized by ring‐opening copolymerization and then reacted with isophorone diisocyanate to form polyurethane (PU) copolymers. The molecular weight of the PU copolymers was measured by gel permeation chromatography, and the chemical structure was analyzed by ¹H‐nuclear magnetic resonance and Fourier transform infrared spectra. Then, the PU copolymers were processed into fibrous scaffolds by the electrospinning technology. The morphology, surface wettability, mechanical strength, and cytotoxicity of the obtained PU fibrous mats were investigated by scanning electron microscopy, water contact angle analysis, tensile test, and MTT analysis. The results show that the molecular weights of PCFC and PU copolymers significantly affected the physicochemical properties of electrospun PU nanofibers. Moreover, their good in vitro biocompatibility showed that the as‐prepared PU nanofibers have great potential for applications in tissue engineering. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43643.     

Synthesis and Characterization of Biodegradable Poly(ε‐caprolactone)‐Polyglycolide‐Poly(ethylene glycol) Monomethyl Ether Random Copolymer

Summary: Poly(ε‐caprolactone)‐polyglycolide‐poly(ethylene glycol) monomethyl ether random copolymers were synthesized from ε‐caprolactone (ε‐CL), glycolide (GA) and poly(ethylene glycol) monomethyl ether (MPEG) using stannous octoate as catalyst at 160 °C by bulk polymerization. The copolymers with different composition were synthesized by adjusting the weight ration of reaction mixture. The resultant copolymer with a weight ratio (10:15:75) of MPEG2000, GA, and CL was characterized by IR, ¹H NMR, GPC and DSC. The new biodegradable copolymer has potential for medical applications since it is combined with properties of PCL, PGA and MPEG.

     

Nanoporous Low Dielectric Cyclosiloxane Bearing Polysilsesquioxane Thin Films Templated by Poly(ε‐caprolactone)

Summary: Dielectric cyclosiloxane bearing polysilsesquioxanes (CS‐PSSQs) were prepared by acid catalyzed polymerization using 2,4,6,8‐tetramethyl‐2,4,6,8‐tetra(trimethoxysilylethyl)cyclotetrasiloxane. The molecular weight, and content of the functional end‐groups of the CS‐PSSQs were found to be dependent on the process parameters, such as the molar ratio of water and catalyst to the ? OCH₃ group of the silane monomer, the amount of solvent, and the poly(ε‐caprolactone) (PCL) content, etc. Based on these CS‐PSSQ prepolymers, nanoporous organic/inorganic hybrid thin films were fabricated by spin‐coating mixtures of these prepolymers with star‐shaped PCL on the silicon substrate, and subsequently heating them at 150 and 250 °C for 1 minute each and then at 420 °C for 1 hour. A dielectric constant as low as 2.28 was achieved for the nanoporous PCL/CS‐PSSQ (3:7 v/v) film, along with low moisture absorption in ambient and water conditions, primarily due to the presence of hydrophobic moieties such as ethylene and methyl groups of the polymer and nano‐sized hydrophobic pores inside the matrix, resulting in the film having stable dielectric properties. Moreover, the PCL/CS‐PSSQ (3:7 v/v) nanohybrid film revealed a nanoporous structure containing ca. 1.52 nm of average‐sized mesopores, as measured by the N₂ adsorption method. The CS‐PSSQ‐only film showed high mechanical strengths having an elastic modulus and hardness of 6.64 and 0.88 GPa, respectively, for the 7 500 Å thick film and 2.41 and 0.38 GPa, respectively, for the PCL/CS‐PSSQ (3:7 v/v) film. In addition, the crack velocity of the CS‐PSSQ‐only film was found to be ca. 10^?11 m · s^?1 in ambient conditions and an aqueous environment, probably due to the enhanced hydrophobicity and mechanical toughness of the incorporated methyl group, siloxane unit and ethylene moieties in the polymer matrix.

     

Enzymatic degradation of blends of poly(ε‐caprolactone) and poly(styrene‐co‐acrylonitrile) by Pseudomonas lipase

In polymer blends, the composition and microcrystalline structure of the blend near surfaces can be markedly different from the bulk properties. In this study, the enzymatic degradation of poly(ε‐caprolactone) (PCL) and its blends with poly(styrene‐co‐acrylonitrile) (SAN) was conducted in a phosphate buffer solution containing Pseudomonas lipase, and the degradation behavior was correlated with the surface properties and crystalline microstructure of the blends. The enzymatic degradation preferentially took place at the amorphous part of PCL film. The melt‐quenched PCL film with low crystallinity and small lamellar thickness showed a higher degradation rate compared with isothermally crystallized (at 36, 40, and 44°C) PCL films. Also, there was a vast difference in the enzymatic degradation behavior of pure PCL and PCL/SAN blends. The pure PCL showed 100% weight loss in a very short time (i.e., 72 h), whereas the PCL/SAN blend containing just 1% SAN showed ～50% weight loss and the degradation ceased, and the blend containing 40% SAN showed almost no weight loss. These results suggest that as degradation proceeds, the nondegradable SAN content increases at the surface of PCL/SAN films and prevents the lipase from attacking the biodegradable PCL chains. This phenomenon was observed even for a very high PCL content in the blend samples. In the blend with low PCL content, the inaccessibility of the amorphous interphase with high SAN content prevented the attack of lipase on the lamellae of PCL. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 868–879, 2002     

Improvement of processability of poly(ε‐caprolactone) by radiation techniques

Improvement of processability of Poly(ε‐caprolactone) (PCL) was achieved by introduction of a branch structure using gamma‐irradiation from a ⁶⁰Co source. Irradiated PCL has higher molecular weight by producting a branch structure. Hence, the irradiation at a lower dose, such as 3 Mrad, leads to a higher melt viscosity. The branched structure gave improved properties for dynamic viscoelasticity and elongational viscosity. High elongational viscosity was observed by entanglement due to branch chain formed during irradiation, and the elongational viscosity for 3 Mrad is higher than 1.5 Mrad. Due to a higher elongational viscosity, PCL foam can be produced by a molding process. Foam produced from irradiated PCL pellets at 3 Mrad has honeycomb‐like structure, and the foam showed higher enzymatic degradation compared to film samples. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1815–1820, 1999     

Crystallization behavior of poly(ϵ‐caprolactone) in poly(ϵ‐caprolactone) and poly(vinyl methyl ether) mixtures

The morphological development and crystallization behavior of poly(?‐caprolactone) (PCL) in miscible mixtures of PCL and poly(vinyl methyl ether) (PVME) were investigated by optical microscopy as a function of the mixture composition and crystallization temperature. The results indicated that the degree of crystallinity of PCL was independent of the mixture composition upon melt crystallization because the glass‐transition temperatures of the mixtures were much lower than the crystallization temperature of PCL. The radii of the PCL spherulites increased linearly with time at crystallization temperatures ranging from 42 to 49°C. The isothermal growth rates of PCL spherulites decreased with the amount of the amorphous PVME components in the mixtures. Accounting for the miscibility of PCL/PVME mixtures, the radial growth rates of PCL spherulites were well described by a kinetic equation involving the Flory–Huggins interaction parameter and the free energy for the nuclei formation in such a way that the theoretical calculations were in good agreement with the experimental data. From the analysis of the equilibrium melting point depression, the interaction energy density of the PVME/PCL system was calculated to be ?3.95 J/cm³. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Crystalline properties of poly(ε‐caprolactone)‐block‐poly(vinyl acetate) block copolymers: influence of synthesis route

Poly(ε‐caprolactone)‐block‐poly(vinyl acetate) (PCL‐b‐PVAc) block copolymers were synthesized using two approaches: a ‘coupling’ approach using click chemistry reaction and a ‘macroinitiator’ route. Different copolymers, varying by their block lengths, were prepared with both methods. PCL is a semi‐crystalline polymer, and consequently PCL blocks of PCL‐b‐PVAc are able to crystallize. The purpose of this work was to analyse the influence of the method of copolymer synthesis on the crystallinity of the PCL blocks. The results indicate a significant decrease of the crystallinity of the PCL blocks in copolymers obtained using the coupling method, compared to PCL homopolymers, in contrast to copolymers obtained through the macroinitiator approach for which the crystallinity of PCL is much less affected. This influence of the synthesis method is explained by the presence, in the copolymers obtained using the click reaction, of a rigid triazol cycle binding the two blocks, limiting their mobility and decreasing the tendency of PCL to crystallize. © 2013 Society of Chemical Industry     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Functionalization of multi‐walled carbon nanotubes with poly(ε‐caprolactone) using click chemistry

Multi‐walled carbon nanotubes (MWNTs) were covalently functionalized with poly(ε‐caprolactone) (PCL) using click chemistry. First, chlorine moiety‐containing PCL was synthesized by the copolymerization of α‐chloro‐ε‐caprolactone with ε‐caprolactone monomer using ring opening polymerization, and further converted to azide moiety‐containing PCL. The alkyne‐functionalized MWNTs were prepared with the treatment of p‐amino propargyl ether using a solvent free diazotization procedure. The covalent functionalization of alkyne‐derived MWNTs with azide moiety‐containing PCL was accomplished using Cu(I)‐catalyzed [3+2] Huisgen dipolar cycloaddition click chemistry. The PCL‐functionalization of MWNTs was confirmed by the measurements of Fourier transform infra‐red, NMR, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphological control of porous ethylene‐vinyl acetate copolymer membrane obtained from a co‐continuous ethylene‐vinyl acetate copolymer/poly(ϵ‐caprolactone) blend

Ethylene‐vinyl acetate copolymer (EVA)/poly(?‐caprolactone) (PCL) blend (50/50 w/w) with co‐continuous morphology was prepared via melt mixing for fabricating microporous EVA membrane materials through selective solvent extraction. Shear flow and quiescent annealing techniques were employed to control co‐continuous phase size in the EVA/PCL blend, and the time‐ and temperature‐dependent relations of phase size were then evaluated theoretically. Using these techniques, microporous EVA membrane materials with various pore sizes ranging from 2 µm to more than 200 µm were obtained. In contrast to the porous EVA membrane prepared by the traditional way of solvent casting/particulate leaching, the as‐obtained microporous membrane shows a higher level of interconnectivity and much narrower pore size distribution with uniform pore structure. © 2013 Society of Chemical Industry     

Molecular Architecture and Enhanced Thermal Stability of Electrospun Poly(ε‐caprolactone)/Aminopropyl Isobutyl Polyhedral Oligomeric Silsesquioxane Hybrid Fibers

Polymer‐based electrospun fibers have been intensively studied as antimicrobial membranes, drug carriers, and energetic materials. Inorganic fillers or small molecules have been routinely added into polymer matrices in order to enhance product functions. However, the electrospinning process is kinetically controlled and solvent rapidly evaporates due to the large surface‐to‐volume ratio of spinning liquid jet. When electrospinning a multicomponent system, complex phase behavior may occur and give rise to interesting internal structures of resulting products. Such kinetically driven phenomena deserve more attention for optimizing product performance. Here, electrospun poly(ε‐caprolactone)(PCL)/aminopropyl‐heptaisobutyl‐polyhedral oligomeric silsesquioxane (AMPOSS) fibers with AMPOSS content up to 30 wt% are studied as a model system to understand the impact of kinetically controlled phase separation on the fibers' internal structure, properties, and thermal stability. With sufficient AMPOSS loading, the hybrid fibers are found to have an AMPOSS‐shell/PCL‐core structure. The thermal stability of the as‐spun PCL/AMPOSS fibers is therefore greatly enhanced.