Blend membranes based on disulfonated poly(aryl ether ether ketone)s (SPEEK) and poly(amide imide) (PAI) for direct methanol fuel cell usages

Highly disulfonated poly(aryl ether ether ketone)s (SPEEK-70) copolymer was synthesized via direct polymerization to precisely control the degree of sulfonation (D_s = 1.40), which was confirmed and estimated by ¹H NMR. As expected, the proton conductivity of SPEEK-70 membrane is 0.084 S/cm at 25 °C and increases to 0.167 S/cm at 80 °C, surpassing that of Nafion^® 117. However, the relatively high methanol crossover and excessively swelling properties limited its usage in DMFC. Poly(amide imide) was blended with SPEEK-70 to improve the methanol resistance and mechanical properties. These blend membranes were characterized as a function of weight fraction of PAI in terms of ion exchange capacity (IEC), water uptake, water desorption, proton conductivity and methanol permeability in detail. Although the proton conductivities decreased upon the addition of PAI, higher selectivity values defined as the ratio of proton conductivity to methanol permeability were found for the blend membranes. Therefore, the SPEEK/PAI blend membranes are promising for usage in DMFC.     

DMFCs用磺化聚醚醚酮/磺化酚酞型聚醚砜共混质子交换膜

A sulfonated poly(ether ether ketone) (SPEEK) membrane with fairly high degree of sulfonation (DS) swells excessively and even dissolves at high temperature. To solve these problems, sulfonated phenolphthalein poly(ether sulfone) (SPES-C, DS 53.7%) is blended with the SPEEK matrix (DS 55.1%, 61.7%) to prepare SPEEK/SPES-C blend membrane. The decrease in swelling degree and methanol permeability of the membrane is dose-dependent. Pure SPEEK (DS 61.7%) membrane dissolves completely in water at 70ºC, whereas the swelling degree of the SPEEK (DS 61.7%)/SPES-C (40%, by mass) membrane is 29.7% at 80ºC. From room temperature to 80ºC, the methanol permeability of all SPEEK (DS 55.1%)/SPES-C blend membranes is about one order of magnitude lower than that of Nafion®115. At higher temperature, the addition of SPES-C polymer increases the dimensional stability and greater proton conductivity can be achieved. The SPEEK (DS 55.1%)/SPES-C (40%, by mass) membrane can withstand temperatures up to 150ºC. The proton conductivity of SPEEK (DS 55.1%)/SPES-C (30%, by mass) membrane approaches 0.16 S•cm－1, matching that of Nafion115 at 140ºC and 100% RH, while pure SPEEK (DS 55.1%) membrane dissolves at 90ºC. The SPEEK/SPES-C blend membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.     

Sulfonated polyether ether ketone composite proton exchange membranes incorporated with a novel hierarchical-structure hybrid nanofiller consisting solid superacid zirconium phosphate and CNTs

How to simultaneously improved the proton conductivity and mechanical strength is a key problem facing currently used proton exchange membranes (PEMs). Herein, a solid inorganic superacid-zirconium phosphate (ZrP) with a two-dimensional layer structure was combined with one-dimensional carbon nanotubes (CNTs) to prepare hybrid nanofiller ZrP-CNTs by an in situ chemical deposition method. The new hybrid nanofiller was then applied to modify sulfonated polyether ether ketone (SPEEK), a widely used PEM matrix, to obtain a series of composite membranes. The structure and properties of the membranes were fully characterized by SEM, XRD, FTIR, TG, tensile properties, and proton conductivity. The results showed that the proton conductivities of the membranes were significantly improved due to the addition of super solid acid-ZrP that has abundant proton sources or proton sites. Moreover, the composite membranes exhibited better mechanical properties and thermal stability than those of pure SPEEK membrane, owing to the great interface interaction and good compatibility between ZrP-CNTs and SPEEK. The composite membrane (2 wt% ZrP-CNTs) demonstrated the optimal comprehensive performance. Its proton conductivity was 36.63 mS cm⁻¹ and its tensile strength was 37.56 MPa, which was 70% and 10%, respectively, higher than those of the pure SPEEK membrane under the same condition.     

Performance of the sulfonated poly ether ether ketone proton exchange membrane modified with sulfonated polystyrene and phosphotungstic acid for microbial fuel cell applications

In this research, the preparation of low cost proton exchange membranes (PEMs) based on sulfonated poly ether ether ketone (SPEEK) for application in the microbial fuel cells (MFCs) is studied. Sulfonated polystyrene (SPS) and phosphotungstic acid (PWA) were employed to improve the performance of PEM through the creation of more proton pathways. At first, the sulfonation of PEEK and polystyrene were performed through two modified methods to obtain uniform and high degree of sulfonation (DS) of the polymers and then, the PEMs were prepared through the solution casting method. Accordingly, the formation of uniform skin layer was confirmed by the SEM micrographs. Blending the aforementioned additives to the SPEEK polymer solution significantly enhanced the proton conductivity, water uptake and durability of the modified membranes. The proton conductivities of SPEEK/SPS and SPEEK/PWA membranes at additive/SPEEK weight ratio of 0.15 were 45.3% and 26.2% higher than that of the commercial Nafion117 membrane, respectively. Moreover, the degradation times for the abovementioned modified membranes were 140 and 350 min which indicated satisfactory oxidation stability. Besides, the aforementioned membranes exhibited two times more water uptake compared to the neat SPEEK membrane. Finally, SPEEK/SPS and SPEEK/PWA membranes produced 68% and 36% higher maximum power in the MFC, compared to the commercial Nafion117 membrane. Therefore, the fabricated PEMs are potentially suitable alternatives to be used in the fuel cell applications.     

高质子传导率及尺寸稳定性复合质子交换膜制备及性能研究

通过2?丙烯酰胺?2?甲基丙磺酸（AMPS）在1种具有多孔结构的金属有机骨架（MOF）UiO?66?NH₂中聚合,获得UiO?66?NH₂/PAMPS杂化填料后将其加入磺化聚醚醚酮（SPEEK）中制备纳米复合质子交换膜,并对纳米填料和膜性能进行了测试和表征。其中,UiO?66?NH₂/PAMPS中MOF组分的有序孔洞能够为质子提供较为快速的传输通道,同时PAMPS组分上的磺酸基团则为这些通道提供了额外的质子传输位点,从而促进了复合膜中的质子传导。结果表明,填料与基体之间的强静电相互作用使复合膜的溶胀率有所下降;当填料含量达到6 %（质量分数,下同）时,复合膜的质子电导率（σ）从0.040 S/cm 提升到0.057 S/cm,比纯SPEEK高42.5 %,而溶胀率由29 %下降到23 %。     

The Preparation of Metal–Organic-Framework/Boron Phosphate Hybrid Materials for Improved Performances in Proton Exchange Membranes

New types of metal–organic framework based hybrid materials are designed and prepared, which involving the hybridization of various content of boron phosphate (BPO₄) with the precursor of HKUST-1. The structure of obtained HKUST-1/BPO₄ hybrid materials (HB) is fully investigated, and then applied to construct sulfonated poly (ether ether ketone) (SPEEK) based proton exchange membranes (SPEEK/HB). Owing to effective interactions between hybrid materials and SPEEK matrix, the achieved composite membranes reflect a considerable improvement in mechanical and thermal stability, oxidative stability, methanol permeation, and proton conductivity. In particular, the tensile strength of SPEEK/HB-20 composite membrane is 41.3 MPa, which is 1.5 times higher than pristine SPEEK, and the methanol permeability reduced to one-third of SPEEK at the same time. The SPEEK/HB-10 displays the highest proton conductivity of 37.4 mS cm⁻¹ at 80 °C, which is obviously higher than pristine SPEEK. These results reveal that the hybridization of HKUST-1 with BPO₄ provide a promising candidate in the modification of proton exchange membranes (PEMs), and this strategy also possess great application potential in other types of MOFs-based hybrid materials.     

Effect of clay modification on the structure and properties of sulfonated poly(ether ether ketone)/clay nanocomposites

Sulfonated poly(ether ether ketone) (SPEEK)/clay hybrid membranes were prepared using three types of commercially available clays, the sodium montmorillonite (IC), hydrophobic organo‐clay with long alkyl chains (OC), and organo‐clay with carboxylic acid end groups (HC). It was found that the SPEEK/HC hybrid membranes achieved the best clay dispersion, with the exfoliation of the clay nano‐platelets when the filler loading was < 10 wt%. The incorporation of the carboxylic acid groups in clay layers also improved the connectivity between the ionic clusters in the membrane, resulting in higher proton conductivity without compromising the dimensional stability of membranes. The selectivity higher than the pristine SPEEK membranes was obtained for the SPEEK/HC hybrid membranes at low filler loading (<10 wt%), with higher proton conductivity and similar methanol permeability. POLYM. COMPOS., 37:2632–2638, 2016. © 2015 Society of Plastics Engineers     

DMFCs用SPEEK/SiOx-S复合质子交换膜

A sulfonated poly(ether ether ketone) (SPEEK) membrane with a fairly high degree of sulfonation (DS) can swell excessively and even dissolve at high temperature. To solve these problems, insolvable functionalized silica powder with sulfonic acid groups (SiOx-S) was added into the SPEEK matrix (DS 55.1%) to prepare SPEEK/ SiOx-S composite membranes. The decrease in both the swelling degree and the methanol permeability of the membranes was a dose-dependent result of addition of the SiOx-S powder. Pure SPEEK membrane swelled 52.6% at 80°C, whereas the SPEEK/SiOx-S (15%, by mass) membrane swelled only 27.3% at the same temperature. From room temperature to 80℃, all SPEEK/SPEEK/SiOx-S composite membranes had methanol permeability of about one order of magnitude lower than that of Nafion&#61650;115. Compared with pure SPEEK membranes, the addition of the SiOx-S powder not only leads to higher proton conductivity, but also increases the dimensional stability at higher temperatures, and greater proton conductivity can be achieved at higher temperature. The SPEEK/SiOx-S (20%, by mass) membrane could withstand temperature up to 145°C, at which in 100% relative humidity (RH) its proton conductivity exceeded slightly that of Nafion&#61650;115 membrane and reached 0.17 S&#8226;cm－1, while pure SPEEK mem-brane dissolved at 90°C. The SPEEK/SiOx-S composite membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.     

Hydrophilic TiO2 decorated carbon nanotubes/sulfonated poly(ether ether ketone) composite proton exchange membranes for fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is currently considered to be one of the most potential candidates of commercial perfluorinated sulfonic acid proton exchange membranes. To balance the proton conductivity and mechanical properties of SPEEK, nano TiO₂ coated carbon nanotubes (TiO₂@CNTs) were prepared using a benzyl alcohol-assisted sol-gel method and then used as a new nanofiller to modify SPEEK to prepare SPEEK/TiO₂@CNTs composite membranes. The thick insulated TiO₂ coating layer can effectively avoid the risk of electronic short-circuiting formed by CNTs, while the hydrophilicity of TiO₂ can also reduce the polar difference between CNTs and SPEEK matrix, thus promoting the homogeneous dispersion of CNTs in the composites. As a result, the composite membranes demonstrated simultaneously improved strength and proton conductivity. Incorporating 5 wt% of TiO₂@CNTs exhibited 31% growth in mechanical strength when compared with pure SPEEK. Moreover, the maximum conductivity was 0.104 S cm⁻¹ (80°C) for the composite membrane with 5 wt% of TiO₂@CNTs, which was nearly twice as high as that of SPEEK membrane (0.052 S cm⁻¹).     

非溶剂对浇铸SPEEK膜性能的影响

首次采用磺化聚醚醚酮/N,N-二甲基甲酰胺(SPEEK/DMF)和非溶剂(四氯乙烯或对二甲苯)组成的铸膜液制备了SPEEK膜.采用交流阻抗法和隔膜扩散法分别考察了膜的质子传导性和透水性能.结果表明,由于在SPEEK/DMF中添加非溶剂,膜的透水率增加了约30％,质子导电率提高了50％左右.非溶剂的加入影响了铸膜液中聚合物的形态、尺寸和团聚情况,从而影响了成膜后膜的性能.本研究提出的控制膜微相结构的新方法将有助于提高SPEEK膜燃料电池性能.     

Sulfonated poly(ether ether ketone)/zirconium tricarboxybutylphosphonate composite proton-exchange membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is a very promising alternative membrane material for direct methanol fuel cells. However, with a fairly high degree of sulfonation (DS), SPEEK membranes can swell excessively and even dissolve at high temperature. This restricts membranes from working above a high tolerable temperature to get high proton conductivity. To deal with this contradictory situation, insolvable zirconium tricarboxybutylphosphonate (Zr(PBTC)) powder was employed to make a composite with SPEEK polymer in an attempt to improve temperature tolerance of the membranes. SPEEK/Zr(PBTC) composite membranes were obtained by casting a homogeneous mixture of Zr(PBTC) and SPEEK in N,N-dimethylacetamide on a glass plate and then evaporating the solvent at 60°C. Many characteristics were investigated, including thermal stability, liquid uptake, methanol permeability and proton conductivity. Results showed significant improvement not only in temperature tolerance, but also in methanol resistance of the SPEEK/Zr(PBTC) composite membranes. The membranes containing 30 wt-% ∼ 40 wt-% of Zr(PBTC) had their methanol permeability around 10⁻⁷ cm²·s⁻¹ at room temperature to 80°C, which was one order of magnitude lower than that of Nafion?115. High proton conductivity of the composite membranes, however, could also be achieved from higher temperature applied. At 100% relative humidity, above 90°C the conductivity of the composite membrane containing 40 wt-% of Zr(PBTC) exceeded that of the Nafion?115 membrane and even reached a high value of 0.36 S·cm⁻¹ at 160°C. Improved applicable temperature and high conductivity of the compositemembrane indicated its promising application inDMFC operations at high temperature. __________ Translated from Acta Polymerica Sinica, 2007, (4): 337–342 [译自:高分子学报]     

直接甲醇燃料电池用新型质子交换膜的研究

以聚醚醚酮(PEEK)为原料,浓硫酸为磺化剂制备了不同磺化度的磺化聚醚醚酮(SPEEK)膜,以及磺化聚醚醚酮与聚乙烯醇(PVA)、正硅酸乙酯(TEOS)、磷钨酸的复合膜.分别对膜的电导率、阻醇性能和吸水率进行了研究.随着SPEEK膜磺化度的增大,膜的电导率有所提高,然而甲醇渗透系数也增大,膜的机械强度明显降低.SPEEK膜的吸水率低于Nafion 115膜,而PVA膜的吸水率则过高.     

Modified Sulfonated Poly(ether ether ketone) Based Mixed Matrix Membranes for Direct Methanol Fuel Cells

Mixed matrix membranes based on zeolite 4A‐methane sulfonic acid (MSA)‐sulfonated poly(ether ether ketone) (SPEEK) are evaluated as a potential polymer electrolyte membrane (PEM) for direct methanol fuel cells (DMFCs). Ion‐exchange capacity, sorption of water, and water–methanol mixture, proton conductivity, and methanol permeability for the mixed‐matrix membranes have been extensively investigated. The mixed‐matrix membranes are also characterized for their cross‐sectional morphology, mechanical, and thermal properties. DMFCs employing SPEEK‐MSA (20 wt.%) blend, zeolite 4A (4 wt.%)‐SPEEK‐MSA (20 wt.%) mixed matrix membranes deliver peak power densities of 130 and 159 mW cm^–2, respectively; while a peak power density of only 95 mW cm^–2 is obtained for the DMFC employing pristine SPEEK membrane at 70 °C. The results showed that these SPEEK based mixed matrix membranes exhibit higher DMFC performance and lower methanol permeability in comparison to Nafion‐117 membrane.     

Proton exchange membranes based on poly(vinylidene fluoride) and sulfonated poly(ether ether ketone)

Blend membranes were obtained by solution casting from poly(vinylidene fluoride) (PVDF) and sulfonated poly(ether ether ketone) (SPEEK) in N,N-dimethylacetamide (DMAc). DSC and XRD were used to characterize the structure of the blend membranes. The effect of PVDF content on the membrane properties was investigated. The methanol permeability, water uptake and the swelling ratio of blend membranes decreased with the increase of PVDF content. Though the proton conductivity decreased upon the addition of PVDF, they were still comparable to that of Nafion^® 117 membrane. Higher selectivities were also found for most blend membranes in comparison with Nafion^® 117 membrane. The effect of methanol concentration on solution uptake, swelling ratio and methanol permeability of the blend membranes was also studied.     

Effect of dispersion state of Cloisite15A® on the performance of SPEEK/Cloisite15A nanocomposite membrane for DMFC application

The introduction of 2,4,6‐triaminopyrimidine (TAP) into sulfonated poly(ether ether ketone) (SPEEK)/Cloisite15A® nanocomposite membranes were investigated for the purpose of maintaining low methanol permeability and suppressing swelling in direct methanol fuel cell (DMFC). SPEEK with 63% of degree of sulfonation (DS) was prepared by sulfonation of PEEK. Cloisite15A (7.5 wt %) along with various weight loading of TAP was incorporated into SPEEK matrix via solution intercalation method. The effect of TAP loading on the SPEEK/Cloisite15A/TAP morphology was studied. The beneficial impact of the SPEEK/Cloisite15A/TAP morphology on the physicochemical properties of the membrane was further discussed. Swelling behavior, ion exchange capacity (IEC), proton conductivity, and methanol permeability of the resultant membranes were determined as a function of Cloisite15A and TAP loadings. Uniform distribution of Cloisite15A particles in the SPEEK polymer matrix in the homogenous SPEEK/Cloisite15A/TAP nanocomposite membranes was confirmed by scanning electron microscopy and X‐ray diffraction. The water uptake of the SPEEK nanocomposite membranes decreased dramatically in the presence of TAP. The significant selectivity of SP/7.5/7.5 nanocomposite membranes could indicate a potential feasibility as a promising electrolyte for DMFC. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of PES on the morphology and properties of proton conducting blends with sulfonated poly(ether ether ketone)

Development of alternate materials to Nafion, based on ionically conducting polymers and their blends is important for the wider applications of proton exchange membrane fuel cells. In this work, blends of sulfonated poly(ether ether ketone) (SPEEK) with poly(ether sulfone) (PES) are investigated. SPEEK with various ion exchange capacity (IEC) was prepared and blended with PES, which is nonionic and hydrophobic in nature. A comparative study of the water uptake, proton conductivity, and thermo‐mechanical characteristics of SPEEK and the blend membranes as a function of the IEC is presented. Addition of PES decreases the water uptake and conductivity of SPEEK. Chemical and thermal stability and mechanical properties of the membrane improve with the addition of PES. The effect of water content on the thermo‐mechanical properties of membranes was also studied. The morphology of blend membranes was studied using SEM to understand the microstructure and miscibility of the components. On the basis of the results, a plausible microstructure of the blends is presented, and is shown to be useful in understanding the variation of different properties with blending. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

聚醚砜/磺化聚醚醚酮共混膜的制备和性能

采用流延法制备了聚醚砜(PES)含量不同的PES/磺化聚醚醚酮(SPEEK)共混膜。PES与SPEEK具有良好的相容性。所制备PES/SPEEK共混膜的含水率、溶胀度和甲醇透过系数均随PES含量的增加而降低。虽然共混膜的质子传导性能有所降低.但阻醇性能和溶胀性能提高,这说明PES/SPEEK共混膜是一种很好的直接甲醇燃料电池用固体高分子电解质膜材料。     

Novel amphoteric ion exchange membranes by blending sulfonated poly(ether ether ketone) with ammonium polyphosphate for vanadium redox flow battery applications

A novel amphoteric ion exchange membrane for vanadium redox flow battery (VRFB) was explored by blending sulfonated poly(ether ether ketone) (SPEEK) and ammonium polyphosphate (APP). The high-stability flame retardant of cross-linked APP with a large number of NH₄⁺ groups was first introduced into SPEEK membrane. It was observed that the addition of APP with special structure could achieve a good balance between proton conductivity and vanadium ions permeability. The abundant NH₄⁺ in APP could block the penetration of vanadium ions by Donnan/Manning exclusion effect and ionic crossing networks due to the ionic bonds between cation and anion groups, and specially a small amount of APP within 5% could remarkably improve the proton conductivity of pristine SPEEK membrane might be ascribed to the unique fast proton transport channels formed by hydrogen bond networks and particular micro-phase separation as a result of interaction between SPEEK and APP. When 5% APP was blended, the SPEEK/APP-5% (S/APP-5%) amphoteric membrane showed a higher selectivity of 20.87 × 10⁴ S min/cm³ (with a good proton conductivity of 0.075 S/cm and a lower VO²⁺ permeability of 3.45 × 10⁻⁷ cm²/ min) and presented better thermal and chemical stability compared to Nafion115 and SPEEK membranes. The VRFB single cell assembled with S/APP-5% amphoteric membrane exhibited more excellent performance than that of Nafion115 and pristine SPEEK membranes, which revealed a higher coulombic efficiency of 96.3%–98.3%, comparable voltage efficiency of 88.4%–78.7% and higher energy efficiency of 85.1%–77.4% from 40 to 80 mA/cm², respectively, and showed relatively good stability of the efficiency up to 50 cycles at 60 mA/cm². The results demonstrated that the designed S/APP amphiprotic membrane of outstanding selectivity, high battery efficiency, and good durability is a prospected VRFB separator.     

磷钨酸/二氧化硅/磺化聚醚醚酮复合膜的制备、表征与性能

以二氧化硅和磷钨酸改性磺化聚醚醚酮制得一种新型磺化聚醚醚酮复合膜。复合膜中杂多酸仍然保持着Keggin型PW12O430-阴离子的特征结构,二氧化硅和磷钨酸以无定形状态均匀分散于复合膜中。磷钨酸/二氧化硅/磺化聚醚醚酮复合膜的阻醇性能优于Nafion115;质子导电性能随着温度的提高有所增加。复合膜在磷钨酸中具有良好的稳定性。     

Solution‐blown SPEEK/POSS nanofiber–nafion hybrid composite membranes for direct methanol fuel cells

This study aims to develop novel hybrid composite membranes (NHMs) by impregnating Nafion solution into the porous sulfonated poly(ether ether ketone)/polyhedral oligomeric silsesquioxanes (SPEEK/POSS) nanofibers (NFs). The composite membrane was prepared by solution blowing of a mixture of SPEEK/POSS solution. The characteristics of the SPEEK/POSS NFs and the NHMs, including morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of NHMs was compared with that of Nafion117 and SPEEK/Nafion composite membranes. Results showed that the introduction of POSS improved the proton conductivity, water swelling, and methanol permeability of membranes. A maximum proton conductivity of 0.163 S cm^?1 was obtained when the POSS content was 6 wt % at 80°C, which was higher than that of Nafion117 and SPEEK/Nafion. NHMs could be used as proton exchange membranes (PEMs) for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42843.