铒掺杂富硅热化SiO2／Si发光薄膜的显微结构

利用金属蒸气真空弧(MEVVA)离子源将稀土元素Er离子掺杂到富硅热氧化SiO2/Si薄膜中.卢瑟福背散射(RBS)和X-射线电子能谱仪(XPS)分析表明,Er浓度可达原子百分数(x)～10,即Er的原子体浓度为～1021·     

Er离子注入的富硅SiO2MOS-LED的可见和红外电致发光特性

通过Er离子和Si离子注入并结合高温退火制备了Er掺杂的富硅SiO2薄膜以及ITO/SiON/富硅SiO2:Er/Si MOS结构电致发光器件.研究了富Si浓度的变化对Er3+离子掺杂的电致发光器件的发光性能和传导特性的影响.发现不同Si含量对Er3+离子的不同能级的电致发光会产生不同作用.在富Si量小于5％的条件下,...     

溶胶-凝胶法Er_2O_3薄膜的结构和光学特性

针对稀土Er掺杂Si光源中Er离子掺杂浓度低的问题,采用溶胶-凝胶(Sol-gel)法在Si(100)和SiO2/Si(100)基片上旋涂法制备Er2O3光学薄膜,Er离子浓度与以前掺杂方法相比提高了2个数量级.900℃热处理获得单一立方结构的Er2O3薄膜材料.光致发光(PL)特性研究表明在654nm波长的激光泵浦下,Er2O3薄膜材料获得了1.535μm的发光峰,并具有较小的温度猝灭1/5.在SiO2/Si(100)基体上制备的Er2O3薄膜材料的光致发光强度比Si(100)基体上制备的薄膜提高2-3倍.研究结果表明具有强光致发光特性的Er2O3薄膜是一种有前景的硅基光源和放大器材料.     

AuSi_x(x=1/2,1/7)纳米颗粒的制备及光致发光性能研究

采用射频磁控溅射法在n型单晶Si(100)衬底上制备Au/Si/Au多层薄膜,并在300℃真空原位退火30min。扫描电子显微镜(SEM)及透射电子显微镜(TEM)观察发现,退火前样品表面是一层平整的薄膜,而退火后样品表面形成均匀分布的岛状纳米颗粒,颗粒直径为10～20nm,面密度约1×1011cm-2。X射线光电子能谱(XPS)及TEM分析表明,退火后样品表面形成单晶结构的AuSix(x=1/2,1/7)纳米颗粒。室温下对退火后样品的光致发光(PL)特性进行测试,样品在580,628和700nm处出现三个发光峰,经过分析这些发光峰与样品表面的SiO2结构,AuSix纳米颗粒周围的悬挂键等缺陷以及样品表面SiO2纳米结构中的无桥联氧等因素有关。     

C(膜)/Si(SiO2)(纳米微粒)/C(膜)热处理的形态及结构分析

用直流辉光溅射＋真空镀膜法制备了一种新型结构的硅基纳米发光材料－C（膜）／Si（SiO2)(纳米微粒）／C（膜）夹层膜,并对其进行了退火处理,用TEM,SEM,XRD和XPS对其进行了形态结构分析,TEM观察表明：Si(SiO2)纳米微粒基本呈球形,粒径在30nm左右,SEM观察表明：夹层膜样品总厚度约为50um ,膜表面比较平整,致密,400度退火后,样品表面变得凹凸不平,出现孔状结构;650度退火后,样品表面最平整,致密且颗粒均匀,XRD分析表明：制备出的夹层膜主要由SiO2和Si 组成,在C原子的还原作用和氧气的化作用的共同作用下,SiO2和Si含量随加热温度的升高而呈现交替变化;400度时,C的还原作用占主导地位,SiO2几乎全部被还原成了Si,此时Si含量最高;400－650度时,氧化作用占主导地位,Si又被氧化成SiO2,Si 含量降低,SiO含量逐渐上升,在650度达到最高,XS分析表明：在加热过程中,C原子逐渐扩散进入Si(SiO2)_微粒层,在650度与Si反应生成了新的SiC。     

(Si,Er)双注入热氧化硅的光致发光

采用强流金属蒸汽真空弧（MEVVA）离子源注入机，先将Si大束流注入热氧化SiO2/单晶硅，直接形成镶嵌在SiO2中的纳米晶Si，再小束流注入Er。Er离子在掺杂层中的浓度可达10^21cm^-3量级，大大地提高了作为孤立发光中心的Er^3 浓度。在77K和室温下，观察到了Er^3 的1.54цm特征发射。     

溶胶-凝胶法Er2O3薄膜的结构和光学特性

针对稀土Er掺杂Si光源中Er离子掺杂浓度低的问题,采用溶胶-凝胶（Sol-gel）法在Si(100)和SiO2/Si(100)基片上旋涂法制备Er₂O₃光学薄膜,Er离子浓度与以前掺杂方法相比提高了2个数量级.900 ℃热处理获得单一立方结构的Er₂O₃薄膜材料.光致发光（PL）特性研究表明在654 nm波长的激光泵浦下,Er₂O₃薄膜材料获得了1.535 μm的发光峰,并具有较小的温度猝灭1/5.在SiO₂/Si(100)基体上制备的Er2O3薄膜材料的光致发光强度比Si(100)基体上制备的薄膜提高2-3倍.研究结果表明具有强光致发光特性的Er₂O₃薄膜是一种有前景的硅基光源和放大器材料.     

离子注入的铝在Si(100)表面的偏析及其引起的纳米团簇和合金晶粒形成现象的实验研究

通过高温退火注入了铝的Si(100)样品,探讨偏析出来的铝在硅表面的热力学行为.由900℃的退火实验发现,偏析出来的铝原子一方面形成Si(100)基底的外延铝膜和铝岛,另一方面与硅原子结合形成尺度约为2—3nm的铝硅团簇.而1200℃的退火实验显示,铝和硅的快速冷凝形成了立方晶系的Al₄Si合金晶粒、尺度约为20—30nm.细小的铝硅团簇在结构上独立于样品基底并且趋于聚集成团,很可能是在高温退火和快速降温过程中形成铝硅合金晶粒的前驱. 关键词： 硅表面 铝掺杂 团簇 4Si')" href="#">Al₄Si     

a—Si：O：H薄膜微结构及其高温退火行为研究

以微区Raman散射、X射线光电子能谱和红外吸收对等离子体增强化学气相沉积（PECVD）法制备的氢化非晶硅氧（a-Si:O:H)薄膜微结构及其退火行为进行了细致研究。结果表明a-Si:O:H薄膜具有明显的相分离结构,富Si相镶嵌于富O相之中,其中富Si相为非氢化四面体结构形式的非晶硅（a-Si),富O相为Si,O,H三种原子随机键合形成的SiOx:H(x≈1.35)。经1150℃高温退火,薄膜中的H全部释出;SiOx:H(x≈1.35)介质在析出部分Si原子的同时发生结构相变,形成稳定的SiO2和SiOx(x≈0.64);在析出的Si原子参与下,薄膜中a-Si颗粒固相晶化的成核和生长过程得以进行,形成纳米晶硅（nc-Si),研究发现此时的薄膜具有典型的壳层结构,在nc-Si颗粒表面和外围SiO2介质之间存在着纳米厚度的SiOx(x≈0.64)中间相。     

退火及溅射气氛对氮化硅薄膜光致发光的影响

利用射频磁控反应溅射方法制备富硅的氮化硅薄膜。衬底材料为抛光的硅片,靶材为硅靶,在Ar-N₂气环境下,通过改变两种气体的组分比来改变样品成分,并在高纯N₂气氛下对其进行高温退火处理。用X射线光电子能谱(XPS)和X射线衍射(XRD)对样品进行了表征,并测试了样品的光致发光谱 (PL)。实验结果表明：X射线光电子能谱中出现了Si—N键合结构,同时还有少量的Si—O键生成,通过计算得出Si/N比值约为1.51,制备出了富硅的氮化硅薄膜;薄膜未经退火前,在可见光区域没有观察到明显的光致发光峰,经过高温退火后,XRD中新出现的衍射峰证实了纳米硅团簇的生成,PL图谱中在可见光区域出现了光致发光峰的蓝移现象,结合XRD结果,用纳米晶的量子限域效应对上述现象进行了合理解释。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.