A 7-ns 140-mW 1-Mb CMOS SRAM with current sense amplifier

A 7-ns 140-mW 1-Mb CMOS SRAM was developed to provide fast access and low power dissipation by using high-speed circuits for a 3-V power supply: a current-sense amplifier and pre-output buffer. The current-sense amplifier shows three times the gain of a conventional voltage-sense amplifier and saves 60% of power dissipation while maintaining a very short sensing delay. The pre-output buffer reduces output delays by 0.5 ns to 0.75 ns. The 6.6-μm² high-density memory cell uses a parallel transistor layout and phase-shifting photolithography. The critical charge that brings about soft error in a memory cell can be drastically increased by adjusting the resistances of poly-PMOS gate electrodes. This can be done without increasing process complexity or memory cell area. The 1-Mb SRAM was fabricated using 0.3-μm CMOS quadrupole-poly and double-metal technology. The chip measures 3.96 mm×7.4 mm (29 mm²)     

A 6-ns 4-Mb CMOS SRAM with offset-voltage-insensitive current senseamplifiers

A 4-Mb CMOS SRAM with 3.84 μm² TFT load cells is fabricated using 0.25-μm CMOS technology and achieves an address access time of 6 ns at a supply voltage of 2.7 V. The use of a current sense amplifier that is insensitive to its offset voltage enables the fast access time. A boosted cell array architecture allows low voltage operation of fast SRAM's using TFT load cells     

A 15-ns 4-Mb CMOS SRAM

A 4-Mb SRAM with a 15-ns access time and a uniquely selectable (×4 or ×1) bit organization has been developed based on a 0.55-μm triple-polysilicon double-metal CMOS technology. An input-controlled PMOS-load (ICPL) sense amplifier, Y-controlled bit-line loads (YCLs), and a transfer word driver (TDW) are three key circuits which have been utilized in addition to the 0.55-μm CMOS technology to achieve the remarkable access time of 15 ns. Bit organization of either ×4 or ×1 can be selected purely electrically, and does not require any pin connection procedure     

A 12.5-ns 16-Mb CMOS SRAM with common-centroid-geometry-layoutsense amplifiers

A 16-Mb CMOS SRAM using 0.4-μm CMOS technology has been developed. This SRAM features common-centroid-geometry (CCG) layout sense amplifiers which shorten the access time by 2.4 ns. A flexible redundancy technique achieves high efficiency without any access penalty. A memory cell with stacked capacitors is fabricated for high soft-error immunity. A 16-Mb SRAM with a chip size of 215 mm² is fabricated and an address access time of 12.5 ns has been achieved     

A 3.3-V 12-ns 16-Mb CMOS SRAM

A 16-Mb CMOS SRAM having an access time of 12 ns under a 3.3-V supply has been developed with a 0.4-μm process technology. An address access time of 12 ns has been achieved by an optimized architecture, the use of an automated transistor size optimizer, and a read-bus midlevel preset scheme (RBMIPS). For better yield and efficient testing, an on-chip test circuit with three test modes has been implemented     

A 9-ns 16-Mb CMOS SRAM with offset-compensated current senseamplifier

A 9-ns 16-Mb CMOS SRAM has been developed using a 0.35-μm CMOS process, The current-mode fully nonequalized data path has been realized in a CMOS SRAM for the first time by using a stabilized feedback current-sense amplifier (SFCA) that provides a small input resistance and an offset compensation effect. To reduce the test time, a bit-line wired-OR parallel test circuit has been implemented     

A 20-ns 4-Mb CMOS SRAM with hierarchical word decoding architecture

A 20 ns 4-Mb CMOS SRAM operating at a single supply voltage of 3.3 V is described. The fast access time has been achieved by a newly proposed word-decoding architecture and a high-speed sense amplifier combined with the address transition detection (ATD) technique. The RAM has the fast address mode, which achieves quicker than 10-ns access, and the 16-b parallel test mode for the reduction of test time. A 0.6-μm process technology featuring quadruple-polysilicon and double-metal wiring is adopted to integrate more than 16 million transistors in a 8.35-mm×18.0-mm die     

A 5-ns 1-Mb ECL BiCMOS SRAM

A 1-Mword×1-b ECL (emitter coupled logic) 10 K I/O (input/output) compatible SRAM (static random-access memory) with 5-ns typical address access time has been developed using double-level poly-Si, double-level metal, 0.8-μm BiCMOS technology. To achieve 5-ns address access time, high-speed X-address decoding circuits with wired-OR predecoders and ECL-to-CMOS voltage-level converters with partial address decoding function and sensing circuits with small differential signal voltage swing were developed. The die and memory cell sizes are 16.8 mm×6.7 mm and 8.5 μm×5.3 μm, respectively. The active power is 1 W at 100-MHz operation     

A 16-ns 1-Mb CMOS EPROM

A 16-ns 1-Mb CMOS EPROM has been developed utilizing high-speed circuit technology and a double-metal process. In order to achieve the fast access time, a differential sensing scheme with address transition detection (ATD) is used. A double-word-line structure is used to reduce word-line delay. High noise immunity is obtained by a bit-line bias circuit and data-latch circuit. Sufficient threshold voltage shift (indispensable for fast access time) is guaranteed by a threshold monitoring program (TMP) scheme. The array is organized as 64 K×16 b, which is suitable for 32-b high-performance microprocessors. The active power is 425 mW, the programming time is 100 μs, and the chip size is 4.94×15.64 mm²     

A 23-ns 4-Mb CMOS SRAM with 0.2-μA standby current

A 4-Mb CMOS SRAM having 0.2-μA standby current at a supply voltage of 3 V has been developed. Current-mirror/PMOS cross-coupled cascade sense-amplifier circuits have achieved the fast address access time of 23 ns. A new noise-immune data-latch circuit has attained power-reduction characteristics at a low operating cycle time without access delay. A 0.5-μm CMOS, four-level poly, two-level metal technology with a polysilicon PMOS load memory cell, yielded a small cell area of 17 μm² and the very small standby current. A quadruple-array, word-decoder architecture allowed a small chip area of 122 mm²     

A 1.8-ns access, 550-MHz, 4.5-Mb CMOS SRAM

An ultrahigh-speed 4.5-Mb CMOS SRAM with 1.8-ns clock-access time, 1.8-ns cycle time, and 9.84-μm² memory cells has been developed using 0.25-μm CMOS technology. Three key circuit techniques for achieving this high speed are a decoder using source-coupled-logic (SCL) circuits combined with reset circuits, a sense amplifier with nMOS source followers, and a sense-amplifier activation-pulse generator that uses a duplicate memory-cell array. The proposed decoder can reduce the delay time between the address input and the word-line signal of the 4.5-Mb SRAM to 68% of that of an SRAM with conventional circuits. The sense amplifier with nMOS source followers can reduce not only the delay time of the sense amplifier but also the power dissipation. In the SRAM, the sense-amplifier activation pulse must be input into the sense amplifier after the signal from the memory cell is input into the sense amplifier. A large timing margin required between these signals results in a large access time in the conventional SRAM. The sense-amplifier activation pulse generator that uses a duplicate memory-cell array can reduce the required timing margin to less than half of the conventional margin. These three techniques are especially useful for realizing ultrahigh-speed SRAM's, which will be used as on-chip or off-chip cache memories in processor systems     

A 15-ns 1-Mbit CMOS SRAM

A 1-Mb CMOS static RAM with a 256 K word×4-bit configuration has been developed. The RAM was fabricated using 0.8-μm double-poly and double-aluminum twin-well CMOS technology. A small cell size of 5.2 μm×8.5 μm and a chip size of 6.15 mm×15.21 mm have been achieved. A fast address access time of 15 ns was achieved using novel circuit techniques: a PMOS-load decoder and a three-stage dynamic gain control sense amplifier combined with an equalization technique and feedback capacitances. A low active current of 50 mA at 20 MHz and low standby currents of 15 mA (TTL) and 2 μA (CMOS) were also attained     

A 46-ns 1-Mbit CMOS SRAM

A 1-Mb (128 K×8-bit) CMOS static RAM (SRAM) with high-resistivity load cell has been developed with 0.8-μm CMOS process technology. Standby power is 25 μW, active power 80 mW at 1-MHz WRITE operation, and access time 46 ns. The SRAM uses a PMOS bit-line DC load to reduce power dissipation in the WRITE cycle, and has a four-block access mode to reduce the testing time. A small 4.8×8.5-μm² cell has been realized by triple-polysilicon layers. The grounded second polysilicon layer increases cell capacitance and suppresses α-particle-induced soft errors. The chip size is 7.6×12.4 mm²     

A 9-ns 1-Mbit CMOS SRAM

A 1-Mbit CMOS static RAM (SRAM) with a typical address access time of 9 ns has been developed. A high-speed sense amplifier circuit, consisting of a three-stage PMOS cross-coupled sense amplifier with a CMOS preamplifier, is the key to the fast access time. A parallel-word-access redundancy architecture, which causes no access time penalty, was also incorporated. A polysilicon PMOS load memory cell, which had a large on-current-to-off-current ratio, gave a much lower soft-error rate than a conventional high-resistance polysilicon load cell. The 1-Mbit SRAM, fabricated using a half-micrometer, triple-poly, and double-metal CMOS technology, operated at a single supply voltage of 5 V. An on-chip power supply converter was incorporated in the SRAM to supply a partial internal supply voltage of 4 V to the high-performance half-micrometer MOS transistors.<>     

A 6-ns, 1.5-V, 4-Mb BiCMOS SRAM

A 0.3-μm 4-Mb BiCMOS SRAM with a 6-ns access time at a minimum supply voltage of 1.5 V has been developed. Circuit technologies contributing to the low-voltage, high-speed operations include: (1) boost-BiNMOS gates for address decoding circuits; (2) an optimized word-boost technique for a highly-resistive-load memory cell; (3) a stepped-down CML cascoded bipolar sense amplifier; (4) optimum boost-voltage detection circuits with dummies for boost-voltage generators     

An 18-ns 1-Mbit CMOS SRAM

A 1-Mb (256 K×4 b) CMOS static random-access memory with a high-resistivity load cell was developed with 0.7-μm CMOS process technology. This SRAM achieved a high-speed access of 18 ns. The SRAM uses a three-phase back-bias generator, a bus level-equalizing circuit and a four-stage sense amplifier. A small 4.8×8.5-μm² cell was realized by the use of a triple-polysilicon structure. The grounded second-polysilicon layer increases cell capacitance and suppresses α-particle-induced soft errors. The chip size measures 7.5×12 mm²     

A 17-ns 4-Mb CMOS DRAM

A 17-ns nonaddress-multiplexed 4-Mb dynamic RAM (DRAM) fabricated with a pure CMOS process is described. The speed limitations of the conventional DRAM sensing technique are discussed, and the advantages of using the direct bit-line sensing technique are explained. A direct bit-line sensing technique with a two-stage amplifier is described. One readout amplifier is composed of a two-stage current-mirror amplifier and a selected readout amplifier is activated by a column decoder output before the selected word line rises. The amplifier then detects a small bit-line signal appearing on a bit-line pair immediately after the word-line rise. This two-stage amplification scheme is essential to improving access time, especially in the case of a CMOS process. The high sensitivity of the readout amplifier is discussed, and the electrical features and characteristics of the fabricated DRAM are reported     

A 65-ns 4-Mbit CMOS DRAM with a twisted driveline sense amplifier

A 4-Mb word/spl times/1-b/1-Mb word/spl times/4-b CMOS DRAM characterized by a twisted driveline sense-amplifier (TDSA) scheme and a multiphase drive circuit which enable faster access time and a smaller peak power supply current, respectively, is described. The implementation of an initialize mode with CAS-before-RAS (CBR) logic control, which reduces the memory-chip initialization time by almost a thousand times, is also discussed. The chip measures 6.38/spl times/17.38 mm/SUP 2/ and has been fabricated by using double-well CMOS technology with a minimum design rule of 0.8 /spl mu/m. A typical access time of 65 ns and a peak power supply current of less then 150 mA have been obtained.     

A 25-ns 1-Mbit CMOS SRAM with loading-free bit lines

A 128 K/spl times/8-b CMOS SRAM is described which achieves a 25-ns access time, less than 40-mA active current at 10 MHz, and 2-/spl mu/A standby current. The novel bit-line circuitry (loading-free bit line), using two kinds of NMOSFETs with different threshold voltages, improves bit-line signal speed and integrity. The two-stage local amplification technique minimizes the data-line delay. The dynamic double-word-line scheme (DDWL) allows the cell array to be divided into 32 sections along the word-line direction without a huge increase in chip area. This allows the DDWL scheme to reduce the core-area delay time and operating power to about half that of other conventional structures. A double-metal 0.8-/spl mu/m twin-tub CMOS technology has been developed to realize the 5.6/spl times/9.5-/spl mu//SUP 2/ cell size and the 6.86/spl times/15.37-mm/SUP 2/ chip size.     

A 14-ns 1-Mbit CMOS SRAM with variable bit organization

The authors describe a 14-ns 1-Mb CMOS SRAM (static random-access memory) with both 1M word×1-b and 256 K word×4-b organizations. The desired organization is selected by forcing the state of an external pin. The fast access time is achieved by the use of a shorter divided-word-line (DWL) structure, a highly sensitive sense amplifier, a gate-controlled data-bus driver, and a dual-level precharging technique. The 0.7-μm double-aluminum and triple-polysilicon process technology with trench isolation offers a memory cell size of 41.6 μm² and a chip size of 86.6 mm ². The variable bit-organization function reduces the testing time while keeping the measurement accuracy of the access times