金属氧化物催化剂在不同气氛中的除氚性能

建立了惰性气氛和含氧气氛的除氚模拟系统,通过三种金属氧化物催化剂(Cu O,Ag-X和H506-2)上除氢性能的考察来优化除氚系统的工艺参数。结果表明金属氧化物催化剂在两种不同气氛下均能够高效除氢,除氢效率99%以上。在此基础上,选用H506-02为除氚催化剂,工作温度为400℃时,建立的小型除氚器可使不同气氛的原气达到深度除氚的效果。     

热处理条件对煤中硒释放行为的影响

利用固定床热解反应装置,研究了平朔、兖州、神华、黑代沟、义马、霍林河和曲靖七种煤中硒在氮气气氛下,200℃～1000℃的热稳定性,考察了加热速率、终温停留时间、气氛（氮气、空气与氢气）对黑代沟和霍林河煤中硒释放规律的影响。结果表明,热解条件下煤中硒主要在700℃以下释放,700℃时的释放率为34%～63%。烟煤中硒的释放峰温在500℃左右,而褐煤中硒的释放峰温在400℃左右。500℃以上,加热速率对煤中硒的释放有一定的影响,较低的加热速率可获得较高释放率;终温1000℃时,停留时间从0延长至15min可明显提高硒的释放率,继续延长停留时间,硒的释放率没有进一步提高。与氮气气氛相比,空气气氛明显促进硒的释放,氢气气氛次之。在热解实验条件下,七种煤中的硒均没有在半焦中富集。     

丙烷在金属铁表面还原NO的实验研究

在程序控温电加热水平陶瓷管反应器、N2气氛和模拟烟气气氛以及300~1 100℃时,对丙烷在金属铁表面还原NO的特性进行了实验研究,并且与相同条件下甲烷在金属铁表面脱硝的效率进行了对比。结果表明,丙烷在金属铁表面能够高效地还原NO。N2气氛中在500~900℃,丙烷在金属铁表面的脱硝效率高于相同含量的甲烷脱硝效率,900℃以上丙烷在金属铁表面的脱硝效率超过95%,并且与甲烷的脱硝效率差别很小。模拟烟气条件下,当过量空气系数SR1小于1.0时,温度超过900℃后丙烷在金属铁表面还原NO的效率能够达到90%以上,且有、无燃尽的情况下,NO的还原率相差不大。在相同的条件下,丙烷在金属铁表面的脱硝效率高于相同条件下甲烷的脱硝效率。SO2对丙烷在金属铁表面还原NO的效率影响很小,可以忽略。     

在钯/纤维氧化铝催化剂上甲烷催化燃烧——燃气催化燃烧远红外辐射器的研究

研制得一种高效、多孔性钯/纤维氧化铝(或钯-铂/纤维氧化铝)催化燃烧板。此板适合于制作以天然气为燃气的远红外辐射器以提高能源的利用效率。当用钯含量为0.41%(以纤维氧化铝为基准)左右的钯/纤维氧化铝燃烧板燃烧天然气时,燃烧效率达96%以上,热强度范围为1.98—2.00kcal/cm~2.hr,废气中一氧化碳含量低于国内外废气规范标准。经500小时寿命试验表明,该板催化活性稳定,在热强度不变的情况下,燃烧效率保持在96%以上,废气中一氧化碳含量<100ppm。与目前所看到的文献报导结果相比,燃烧效率较之高2—6%左右,热强度高15—50%左右。此板亦可用作其他燃气的催化燃烧。     

原子荧光光谱法测定工作场所空气中的锑

用微孔滤膜采集工作场所空气中气溶胶态锑及其化合物,采集的样品经消解后用原子荧光光谱法测定其中的锑含量。对还原隐蔽剂的选择及样品的稳定性进行了探讨。锑浓度在0.0～40.0μg/L范围内与荧光强度呈良好的线性关系,相关系数r=0.9996,加标回收率为93.6%～97.1%,方法的检出限为0.10μg/L,测定结果的相对标准偏差为1.52%～3.19%(n=6)。该方法适用于工作场所空气中锑浓度的测定。     

水蒸气对甲烷在金属铁表面还原NO行为的影响

采用程序控温电加热水平陶瓷管反应器,在N2气氛和模拟烟气气氛中、300~1100℃下,研究了水蒸气对甲烷在金属铁表面还原NO行为的影响,并对反应前、后铁样品进行了X光衍射(XRD)、扫描电子显微镜(SEM)及X光电子能谱(XPS)等表征。结果表明,水蒸气对甲烷在金属铁表面还原NO行为的影响较小。在N2气氛中,水蒸气参与了金属铁的氧化;与无水蒸气时相比,水蒸气存在时NO还原效率有所下降。当水蒸气含量从2.5%增加到7%时,由于水蒸气对金属铁的氧化导致其表面形成疏松的微观孔隙,使得NO的还原效率随水蒸气含量的增加而提高。甲烷则参与了铁氧化物的还原,使铁样品表面形成相对致密的Fe3O4和FeO氧化层,不利于NO与金属铁的接触,使得NO的还原效率低于无甲烷时的结果。在模拟烟气条件下,水蒸气使得甲烷在金属铁表面还原NO的效率增加;在1050℃下,反应段过量空气系数SR1=0.7和燃尽段过量空气系数SR2=1.2时,含7%的H2O和无H2O条件下脱硝效率分别为96.7%和90.6%。而在湿烟气中SO2使NO还原效率略有下降。持久性脱硝实验结果表明,当反应温度为1050℃时,在含7%的H2O、0.02%的SO2的模拟烟气中,1.14%的甲烷在金属铁表面持续50h都能保持90%以上的脱硝效率。     

亚甲基蓝分光光度法测定锑浸出液中硫化钠

湿法炼锑中常采用硫化钠作为从锑矿中提取锑硫化物的浸出剂。准确测定锑浸出液中的硫化钠浓度对掌握和完善湿法炼锑工艺、提高生产效率有重要作用。将亚甲基蓝分光光度法用于锑浸出液中硫化钠的测定,考察了波长选择、体系酸度、显色时间、基质干扰等条件,测评、优化了方法;将方法应用于锑浸出液中硫化钠的测定,方法检出限为0.002mg/L,测定结果相对标准偏差≤3%,加标回收率≥90%。方法能较理想地应用于锑浸出液中硫化钠的测定,丰富了锑浸出液中硫化钠的测定方法,也为相关研究提供了支持与参考。     

亚甲基蓝分光光度法测定锑浸出液中硫化钠

湿法炼锑中常采用硫化钠作为从锑矿中提取锑硫化物的浸出剂。准确测定锑浸出液中的硫化钠浓度对掌握和完善湿法炼锑工艺、提高生产效率有重要作用。将亚甲基蓝分光光度法用于锑浸出液中硫化钠的测定,考察了波长选择、体系酸度、显色时间、基质干扰等条件,测评、优化了方法;将方法应用于锑浸出液中硫化钠的测定,方法检出限为0.002mg/L,测定结果相对标准偏差≤3%,加标回收率≥90%。方法能较理想地应用于锑浸出液中硫化钠的测定,丰富了锑浸出液中硫化钠的测定方法,也为相关研究提供了支持与参考。     

SO_2对甲烷在金属铁表面还原NO的反应影响

采用卧式程序控温电加热陶瓷管反应器,在N2和模拟烟气气氛中、300~1 100℃下,研究了SO2对甲烷在金属铁及其氧化物表面还原NO反应的影响。采用XRD等手段对反应前后铁催化剂样品的组成变化进行了表征,分析了SO2在甲烷-铁脱硝反应中的作用机理。结果表明,甲烷在金属铁及氧化铁表面能够高效率地还原NO,NO还原效率不受烟气中SO2的影响。在SO2体积分数为0.01%~0.04%的N2气氛中,温度高于700℃时,金属铁上NO还原率和SO2脱除率可同时达到100%。在SO2体积分数为0.01%~0.04%的模拟烟气中,当温度高于850℃时,NO还原效率达到90%以上;温度为950℃时,NO还原效率达到98%,SO2对NO还原效率的影响可忽略。当反应温度为1 000℃时,在含0.02%SO2的模拟烟气中,甲烷的体积分数为1.13%时,持续100 h金属铁表面上的NO还原效率都能保持95%以上。     

浆态法制备的MoVTeNbO催化剂上的乙烷氧化脱氢

 采用浆态法在N2气氛下焙烧制得了MoV0.3Te0.23Nb0.1Ox催化剂. 在以该催化剂催化的乙烷氧化脱氢制乙烯的反应中,440 ℃下乙烷的转化率和乙烯的选择性均在90%左右,乙烯产率达80.9%. 但在空气气氛下焙烧得到的催化剂几乎没有催化活性. 用XRD和SEM等方法考察了催化剂的结构.     

The study of PVP/Pd/IrO(2) modified sensor for amperometric determination of sulfur dioxide

A novel electrochemical sensor for the detection of sulfur dioxide in both gas and solution is described. The chemically modified electrode was constructed by polymerizing (4-VP), palladium and iridium oxide (PVP/Pd/IrO(2)) onto a platinum microelectrode which exhibits excellent catalytic activity toward sulfite with an oxidation potential of +0.50 V. The SO(2) gas sensor is based on the PVP/Pd/IrO(2) modified electrode as working electrode, Ag/AgCl electrode as reference electrode, Pt electrode as counter electrode and a porous film, which is in direct contact with the gas-containing atmosphere. The effect of different internal electrolyte solutions of hydrochloric acid, sulfuric acid, phosphates buffer solution, mixed solution of dimethyl sulfoxide and sulfuric acid to the determination of SO(2) was also studied. The sensor was found to have a high current sensitivity, a short response time and a good reproducibility for the detection of SO(2). It has good potential to be used in the field of environmental monitoring and controlling.     

Desorption behavior of carrier free tritium from the inner surface of a glass ampoule

The desorption behavior of tritium from the glass ampoule which originally contained 37 GBq of carrier free tritium gas was studied by etching the surface with a diluted hydrofluoric acid solution or by heating at the constant rate up to 800 degrees C. The total amount of tritium sorbed on the inner surface of the ampoule was found to be 3.9 +/- 0.7 GBq. This value corresponded to more than 10% of tritium contained in the ampoule. The release rate of tritiated water (HTO) was 2.3 kBq/cm2.min, and the amount of HTO desorbed was strongly depended on the atmosphere. Thus, special precaution should be paid to the processing of a vessel once containing such an amount of tritium.     

酸性溶液中钯催化醇电化学氧化的研究

应用电化学循环伏安法(CV)和现场红外光谱(FTIR),研究了酸性溶液中钯催化甲醇、乙二醇电氧化的过程.结果表明:在酸性和中性介质中,甲醇和乙二醇在多晶Pd电极上氧化须在1.5V以上才能发生.随着溶液pH值的降低,过电位减小且峰电流密度上升.溶液的pH值以及电极表面形成的吸附含氧物种对Pd电催化氧化醇有显著的影响.现场红外光谱电化学测试显示,在高电位和强酸性介质中,乙二醇在Pd电极上的氧化产物主要是CO2和少量的乙二酸.在酸性和中性介质中,无论在低电位或高电位,甲醇和乙二醇在Pd上氧化的主要产物是CO2,没有发现CO的存在,说明该氧化过程CO2是经过非毒化的路径产生的.     

Phosphine-free polystyrene-supported palladium(II) complex as an efficient catalyst for the Heck and Suzuki coupling reactions in water

A palladium complex, 1-phenyl-1,2-propanedione-2-oxime thiosemi-carbazone-functionalized polystyrene resin supported Pd(II), is found to be a highly active catalyst for the Heck reaction of methyl acrylate with aryl halides and Suzuki reaction of phenylboronic acid with aryl iodides and bromides, giving excellent yields. The reactions were performed under phosphine-free conditions in an air atmosphere. The palladium catalyst is easily separated, and can be reused for several times without a significant loss in its catalytic activity.     

Polycrystalline and monocrystalline antimony, iridium and palladium as electrode material for pH-sensing electrodes

Different ways of making pH-sensing electrodes from monocrystalline or polycrystalline antimony, iridium and palladium have been investigated. Monocrystalline antimony and iridium are superior to the polycrystalline elements with respect to reproducibility between electrodes and stability of the electrode potential over long periods of time. No good palladium/palladium oxide electrode could be obtained by electrochemical oxidation and the thermal preparation method could not take advantage of the properties of the monocrystalline palladium. Therefore, only polycrystalline palladium was used to study this type of electrodes. The different electrodes were compared with respect to the manner of preparation, the pH-response (reproducibility and time response) and the effect that different complexing ligands present in the measuring solutions may have on the electrode response. Also, the redox-response of the electrodes and the effect of different oxygen pressures on the electrode potentials were studied. The monocrystalline antimony electrodes have the best reproducibility and long-term stability but also respond to complexing ligands and to variations in the oxygen pressure. Monocrystalline iridium electrodes can be obtained by continuously cycling the potential between -0.25 and +1.25 V (SCE) in 0.5M sulphuric acid. They do not respond to the complexing ligands tested, and have fairly good long-term stability, but the reproducibility between electrodes is inferior to that of the monocrystalline antimony electrodes. Polycrystalline antimony and iridium electrodes were inferior to the monocrystalline ones. The properties of the palladium electrodes were similar to those of the iridium ones.     

Analytical method for atmospheric tritium with a portable tritium sampling system

A portable tritium sampler was developed for the stepwise collections of water vapour (HTO), hydrogen (HT) and hydrocarbons (CH₃T) in the atmosphere. First, water vapour was collected in an electronic cooler and an HTO collection column containing 400 g of molecular sieve. Next, dried air was introduced into an HT collection column containing 150 g of palladium catalyst. Hydrogen was then converted to water by catalytic oxidation at room temperature and the resultant water was immediately adsorbed on the molecular sieve bed supporting the catalyst. The remaining gas was finally introduced into a CH₃T collection column containing 100 g of molecular sieve through a platinum catalyst column, in which hydrocarbons were burnt at 400°C. The resultant water was adsorbed in the CH₃T collection column. The collection efficiencies of water in the HTO, HT and CH₃T collection columns were all estimated to be nearly 100%. This newly developed method was found to be useful for the routine tritium monitoring by applying it to actual air samples.     

Polymethyl methacrylate micro-spheres supported palladium: A new catalyst for Heck and Suzuki reactions

Polymethyl methacrylate (PMMA) micro-spheres, a kind of commercially available polymeric material was treated with PdCl₂ and formaldehyde giving a reagent with a palladium loading of 0.79 (wt.%). The Pd-PMMA catalyzed the highly efficient Heck and Suzuki reactions. The reactions can be performed under ligand-free conditions in an air atmosphere. The palladium catalyst is easily separated and can be reusable with negligible leaching of palladium.     

Further Study of CO2 Electrochemical Reduction on Palladium Modified BDD Electrode: Influence of Electrolyte

The study of CO₂ electrochemical reduction to useful compounds using bare or modified BDD electrode attracts numerous attentions. Meanwhile, the efficiency of products obtained from CO₂ electrochemical reduction is known to be determined by the electrode material and the electrolyte. Formic acid as main product and CO as a minor product, have also been known on the CO₂ reduction using BDD electrode. Recently, we reported the successful improvement of CO production from the reduction of CO₂ by decorating the surface of BDD electrode with palladium particles. Following this, herein, we present further investigation on electrolyte dependence, including cation and anion dependence and also concentration effect in order to understand deeply the CO₂ reduction on surface of palladium modified BDD electrode. The results suggest the use of NaCl and KCl as a catholyte for optimum performance, in addition to the improvement of CO₂ reduction product in higher electrolyte concentration.     

Experimental investigation on tritium gettering with hydrogen uranyl phosphate (HUP)

At room-temperature and atmospheric pressure, using electrode disks of various sizes, under the action 4 7Vdc eletric field, we gettered tritium gas from 2.2L of air containing (0.15 18.61)×10⁸ Bq of tritium and (3000 12000) ppm of moisture during 50 hours or so the efficiency of gettering tritium was over 95%. Applying liquid scintillation counting method, we measured the tritium in the disks after gettering, and found that the amounts of tritium in the disks were equal to those reduced in the tested tritiated air.     

Use of micromolded carbon dual electrodes with a palladium decoupler for amperometric detection in microchip electrophoresis

The fabrication and evaluation of micromolded dual carbon ink electrodes and their integration with a fabricated palladium decoupler for use in microchip electrophoresis is described. As opposed to previous work involving carbon-based dual electrodes with microchip electrophoresis, this approach results in electrodes that are amenable to mass production in a manner where the decoupler/electrode alignment is fixed and reproducible. In this work, electrode sizes and spacings were optimized to result in dual carbon electrodes that are 1 microm in height and separated by 100 microm. Fluorescence microscopy was used to investigate leakage around the electrode/channel interface as well as to investigate what effect the dual electrodes have on band broadening phenomena. The performance of the microelectrodes was demonstrated by the separation and selective dual electrode detection of neurotransmitters in the presence of ascorbic acid. It was also found that addition of SDS to the buffer system improved both the LODs and collection efficiencies. This approach, which is the first involving carbon-based dual electrodes with an on-chip palladium decoupler, will be useful for separating and detecting neurotransmitters that are either collected by in vivo sampling or released from cells on-chip.