Flexural Behavior of R/C Beams Strengthened with Carbon Fiber Reinforced Polymer Sheets or Fabric

Their resistance to electro-chemical corrosion, high strength-to-weight ratio, larger creep strain, fatigue resistance, and nonmagnetic and nonmetallic properties make carbon fiber reinforced polymer (CFRP) composites a viable alternative to bonding of steel plates in repair and rehabilitation of reinforced concrete structures. The objective of this investigation is to study the effectiveness of externally bonded CFRP sheets or carbon fiber fabric in increasing the flexural strength of concrete beams. Four-point bending flexural tests were conducted up to failure on nine concrete beams strengthened with different layouts of CFRP sheets and carbon fiber fabric and on three beams with different layouts of anchored CFRP sheets. An analytical procedure, based on compatibility of deformations and equilibrium of forces, was presented to predict the flexural behavior of beams strengthened with CFRP sheets and carbon fiber fabric. Comparisons were made between the test results and the analytical calculations. The flexural strength was increased up to 58% on concrete beams strengthened with anchored CFRP sheets.     

Fatigue Behavior of RC Beams Strengthened with GFRP Sheets

The objective of the presented study is to examine the effects of glass fiber reinforced polymer (GFRP) composite rehabilitation systems on the fatigue performance of reinforced concrete beams. Experiments were conducted on beams with and without GFRP composite sheets on their tensile surfaces. The specimens were 152 × 152 × 1,321 mm reinforced concrete beams with enough transverse reinforcement to avoid shear failure. The results of this study indicate that the fatigue life of reinforced concrete beams with the given geometry, subjected to the same cycling load, can be significantly extended through the use of externally bonded GFRP composite sheets. An interesting finding is that, although the fiber strengthening system increases the fatigue life of the beams, the failure mechanism, fatigue of the steel reinforcement, remains the same in both strengthened and nonstrengthened beams. Thus, it is possible to predict the fatigue life of a cyclically loaded beam using existing fatigue models.     

Prestressed Carbon Fiber Reinforced Polymer Sheets for Strengthening Concrete Beams at Room and Low Temperatures

A technique for strengthening damaged concrete beams using prestressed carbon fiber reinforced polymer (CFRP) sheets was developed at Queen’s University and the Royal Military College of Canada. As part of this study, an anchorage system was developed to directly prestress the CFRP sheets by jacking and reacting against the strengthened concrete beam itself. The feasibility and effectiveness of using bonded prestressed CFRP sheets to strengthen precracked concrete beams at both room (+22°C,+72°F) and low (?28°C,?20°F) temperatures have been investigated experimentally. Materials and prestress changes due to temperature variations that would affect and cause changes in flexural behavior were studied. The strengthened beams showed significant increases in flexural stiffness and ultimate capacity as compared to the control-unstrengthened beams. The flexural behavior of the strengthened beams was not adversely affected by short-term exposure to reduced temperature (?28°C,?20°F). In addition to the experimental investigation, analytical models were developed to predict the overall flexural behavior of the strengthened beams during prestressing of the CFRP sheets and under external loading at both room and low temperatures. The model accurately predicted the flexural beam behavior. Improved serviceability behavior and higher strength were predicted for beams strengthened with the bonded prestressed CFRP sheets.     

Fatigue of Reinforced Concrete Beams Strengthened with Steel-Reinforced Inorganic Polymers

Steel-reinforced polymer (SRP) composite materials are very attractive due to their low weight and high strength. The ease of installation which significantly reduces repair time and expense is another major advantage. One of the main disadvantages of SRP materials is that the matrices used for their fabrication are typically organic and thus they are susceptible to fire. In this study, a newly developed retrofit system is being used. It consists of high strength steel fibers impregnated in a fireproof inorganic matrix. The objective of this study is to examine the effects of this hybrid rehabilitation system on the fatigue performance of strengthened reinforced concrete beams. Sixteen 100?mm×150?mm×1200?mm reinforced concrete beams with enough transverse reinforcement to avoid shear failure were used in this study. Nine beams were strengthened with steel fiber sheets on their tension faces. The results from the present study indicate that the fatigue life of reinforced concrete beams, subjected to the same cycling load, can be significantly extended using externally bonded sheets. A rather important finding is that although the strengthening system increases the fatigue life of the beams, the failure mechanism remains the same in both strengthened and nonstrengthened beams. Thus, it is possible to predict the fatigue life of a cyclically loaded beam using existing fatigue models. Furthermore, no delamination failures were observed due to fatigue loading.     

Prestressed FRP Sheets for Poststrengthening Reinforced Concrete Beams

Four large-scale reinforced concrete beams were constructed and tested to investigate the effectiveness of external poststrengthening with prestressed fiber reinforced polymer (FRP) sheets. One of the beams served as a control specimen, another was strengthened with nonprestressed carbon FRP sheets, and the remaining two were strengthened with prestressed carbon FRP sheets. Presented is a method of prestressing multiple layers of the carbon fiber sheets during the application process and the experimental and analytical behavior of the beams under quasi-static loading. Comparisons are made between the control beam, the beam reinforced with nonprestressed carbon FRP sheets, and the beams strengthened with prestressed sheets. Serviceability and ultimate conditions are considered in the theoretical prediction of beam behavior, including the effects of multiple layer prestressing and external loading. The bonding of prestressed FRP sheets to the tensile face of concrete beams improved both the serviceability and the ultimate behavior of the reinforced concrete beams.     

Behavior of Concrete Beams Strengthened in Shear with Carbon-Fiber Sheets

This paper presents the results of a test program for shear strengthening characteristics of continuous unidirectional flexible carbon-fiber polymer sheets bonded to reinforced concrete (RC) beams. A total of eight 150?mm×200?mm×2,600?mm concrete beams were tested. Various sheet configurations and layouts were studied to determine their effects on ultimate shear strength of the beams. From the tests, it was found that the externally adhesive bonded flexible carbon-fiber sheets are effective in strengthening RC beams in shear. Further, it was observed that the strength increases with the number of sheet layers and the depth of sheets across the beam section. Among the various schemes of wrapping studied, vertical U-wrap of sheet provided the most effective strengthening for concrete beam. Beam strengthened using this scheme showed 119% increase in shear capacity as compared to the control beam without any strengthening. Two prediction models available in literature for computing the shear contribution of carbon-fiber tow sheets to the shear capacity of fiber reinforced polymers bonded beams were compared with the experimental results.     

Flexural Behavior of Reinforced Concrete Beams Strengthened with CFRP Sheets and Epoxy Mortar

Experiments were conducted to study the effect of using epoxy mortar patch end anchorages on the flexural behavior of reinforced concrete beams strengthened with carbon fiber-reinforced polymer (CFRP) sheets. More specifically, the effect of the end anchorage on strength, deflection, flexural strain, and interfacial shear stress was examined. The test results show that premature debonding failure of reinforced concrete beams strengthened with CFRP sheet can be delayed or prevented by using epoxy mortar patch end anchorages. A modified analytical procedure for evaluating the flexural capacity of reinforced concrete beams strengthened with CFRP sheets and epoxy mortar end anchorage is developed and provides a good prediction of test results.     

Behavior of Concrete Beams Strengthened with Fiber-Reinforced Polymer Laminates under Impact Loading

Most of the research on application of composite materials in civil engineering during the past decade has concentrated on the behavior of structural elements under static loads. In engineering practice, there are many situations in which structures undergo impact or dynamic loading. In particular, the impact response of concrete beams strengthened with composite materials is of interest. This paper presents the results of an experimental investigation conducted to study the impact effects on concrete beams strengthened with fiber-reinforced polymer laminates. Two types of composite laminates, carbon and Kevlar, were bonded to the top and bottom faces of concrete beams with epoxy. Five beams were tested: two strengthened with Kevlar laminates, two strengthened with carbon laminates, and one unretrofitted beam as the control specimen. The impact load was applied by dropping a steel cylinder from a specified height onto the top face of the beam. The test results revealed that composite laminates significantly increased the capacity of the concrete beams to resist impact load. In addition, the laminates reduced the deflection and crack width. Comparing the test results of the beams strengthened with Kevlar and carbon laminates indicated that the gain in strength depends on the type, thickness, weight, and material properties of the composite laminate.     

Strength and Ductility of RC Beams Repaired with Bonded CFRP Laminates

The objective of this study is to investigate the strength and ductility aspects of reinforced concrete (RC) beams strengthened with an externally bonded carbon fiber reinforced polymer (CFRP) laminate and to examine how such retrofitting affects strength, deflection, curvature, and energy, as exemplified by the area under the load-deflection curve of the strengthened composite beam. Three series of tests on eleven RC beams were carried out and their ultimate load capacities and ductilities evaluated. The variables in the experimental program were longitudinal steel ratio, volume of internal stirrups, and the location and configuration of external anchorages. The results show that both deflection and energy absorption are drastically reduced when beams are strengthened with bonded CFRP plates without external anchorages. Suitably designed and positioned external anchorages allow much of this lost ductility to be regained; however, even then the ductility of the strengthened beam cannot be restored to its original level. It is shown that definitions of ductility based on deflection and energy are able to give a good and rational representation of the physical aspects of ductility of RC beams strengthened with bonded CFRP laminates with or without external anchorages. The results show that the effects on ductility arising from strengthening existing RC beams with CFRP laminates cannot be ignored, even if it is not clear at this stage how to apply the concept of ductility indices and ductility ratios developed in this paper in design practice.     

Fatigue Performance of RC Beams Strengthened in Shear with CFRP Fabrics

In recent years, a tremendous effort has been directed toward understanding and promoting the use of externally bonded fiber-reinforced polymer (FRP) composites to strengthen concrete structures. Despite this research effort, studies on the behavior of beams strengthened with FRP under fatigue loading are relatively few, especially with regard to its shear-strengthening aspect. This study aims to examine the fatigue performance of RC beams strengthened in shear using carbon FRP (CFRP) sheets. It involves six laboratory tests performed on full-size T-beams, where the following parameters are investigated: (1) the FRP ratio and (2) the internal transverse-steel reinforcement ratio. The major finding of this study is that specimens strengthened with one layer of CFRP survived 5 million cycles, some of them with no apparent signs of damage, demonstrating thereby the effectiveness of FRP strengthening systems on extending the fatigue life of structures. Specimens strengthened with two layers of CFRP failed in fatigue well below 5 million cycles. The failure mode observed for these specimens was a combination of crushing of the concrete struts, local debonding of CFRP, and yielding of steel stirrups. This failure may be attributed to the higher load amplitude and also to the greater stiffness of the FRP which may have changed the stress distribution among the different components coming into play. Finally, comparison between the performance of specimens with transverse steel and without seems to indicate that the addition of transverse steel extends the fatigue life of RC beams.     

Strengthening of Short Shear Span Reinforced Concrete T Joists with Fiber-Reinforced Plasic Composites

In this work, the results of an experimental study conducted in a 1964-vintage building are presented. Twelve reinforced concrete (RC) T-joists strengthened with fiber-reinforced plastic (FRP) composites were loaded until failure in a short shear span configuration. Different strengthening schemes, including different FRP materials and a new FRP anchorage system, were adopted in order to compare the performance of the different installations. Carbon FRP and aramid FRP sheets in an epoxy matrix were bonded to the RC joists using the wet layup technique. All of the joists were loaded close to one end support and showed similar cracking patterns at failure. The design calculations were based on experimental results. All of the unanchored FRP strengthened beams showed failure due to peeling, while the anchored FRP strengthened members showed failure due to anchor pullout at higher load values. It was found that an increase in the amount of FRP did not result in a proportional increase in the shear capacity, as expected by design equations, but all of the beams showed a considerable increase in stiffness. The experimental results are compared with the results expected by analytical models in order to discuss the structural behavior of FRP strengthened beams tested in a real building with a short shear span. It was found that theoretical calculations resulted in nonconservative results for the tested specimens.     

Concrete Beams Strengthened with Prestressed Near Surface Mounted CFRP

Retrofitting concrete structures with fiber reinforced polymer (FRP) has today grown to be a widely used method throughout most parts of the world. The main reason for this is that it is possible to obtain a good strengthening effect with a relatively small work effort. It is also possible to carry out strengthening work without changing the appearance or dimensions of the structure. Nevertheless, when strengthening a structure with external FRP, it is often not possible to make full use of the FRP. The reason for this depends mainly on the fact that a strain distribution exists over the section due to dead load or other loads that cannot be removed during strengthening. This implies that steel yielding in the reinforcement may already be occurring in the service limit state or that compressive failure in the concrete is occurring. By prestressing, a higher utilization of the FRP material is made possible. It is extremely important to ensure that, if external prestressing is used, the force is properly transferred to the structure. Most of the research conducted with prestressing carbon fiber reinforced polymer (CFRP) for strengthening has been on surface bonded laminates. However, this paper presents research on prestressed CFRP quadratic rods bonded in sawed grooves in the concrete cover. This method has proven to be an advantageous means of bonding CFRP to concrete, and in comparison to surface bonded laminates, the shear and normal stress between the CFRP and the concrete are more efficiently transferred to the structure. In the presented test, no mechanical device has been used to maintain the prestress during testing, which means that the adhesive must transfer all shear stresses to the concrete. Fifteen beams with a length of 4?m have been tested. The tests show that the prestressed beams exhibited a higher first-crack load as well as a higher steel-yielding load as compared to nonprestressed strengthened beams. The ultimate load at failure was also higher, as compared to nonprestressed beams, but in relation not as large as for the cracking and yielding. In addition, the beams strengthened with prestressed FRP had a smaller midpoint deflection. All strengthened beams failed due to fiber rupture of the FRP.     

Seismic Rehabilitation of Corner RC Beam-Column Joints Using CFRP Composites

In this paper, efficiency and effectiveness of carbon fiber reinforced polymers (CFRPs) in upgrading the shear strength and ductility of seismically deficient corner or knee reinforced concrete beam-column joints have been studied. For this purpose, four as-built corner/knee joints were constructed with no transverse reinforcement, representing extreme case of preseismic code design construction practice of joints and encompassing many existing beam-column corner joints. Out of these four as-built specimens, two specimens were used as baseline specimens (control specimens) and other two were strengthened with CFRP sheets under two different schemes (strengthened specimens). In the first scheme, CFRP sheets were epoxy bonded to joint, beams, and part of the column regions. In the second scheme, however, sheets were epoxy bonded to joint region only but they were effectively prevented against any possible debonding through mechanical anchorages. All these four subassemblages were subjected to cyclic lateral load histories to simulate loading due to earthquake and provide the equivalent of severe earthquake damage. The damaged control specimens were then repaired by filling their cracks through epoxy and externally bonding them with CFRP sheets under the same above two schemes. These repaired specimens were subjected to the similar cyclic lateral load history and their response histories were obtained. Response histories of control, repaired, and strengthened specimens were then compared. The results were compared through hysteretic loops, load-displacement envelopes, column profiles, ductility, and stiffness degradation. The comparison shows that CFRP sheets are very effective in improving shear resistance and deformation capacity of the corner beam-column joints and delaying their stiffness degradation. Shear capacities of control, repaired, and strengthened specimens were also predicted using writers’ published formulation. The predicted shear capacities were in a good agreement with the experimental values.     

Strengthening of Preloaded RC Beams Using Hybrid Carbon Sheets

Reinforced concrete (RC) beams subject to service loads of 40 or 60% of steel yielding were strengthened using hybrid continuous carbon fiber sheets. The hybrid systems were made of high-strength and high-modulus carbon sheets, and compared with systems using only high-strength carbon. It was found that the use of high-modulus carbon sheets in hybrid systems could increase the yielding load, the flexural stiffness, the postyielding ductility, and reduce the crack opening in concrete. The slope changes on load-deflection curves at steel yielding are not noticeable in hybrid systems. The tensile strains developed in hybrid sheets after the fracture of high-modulus carbon are higher in magnitude and distributed in a larger area, leading to an ultimate carbon fracture with concrete crushing. These unique features are attributed to the high stiffness and low ultimate tensile strain of the high-modulus carbon fibers which stiffen the structures, avoid or delay the fiber-reinforced polymer debonding, and facilitate the deformability during their subsequent breakdown.     

Flexural Strengthening of RC Beams with Cement-Based Composites

In this paper, the effectiveness of fiber-reinforced cementitious matrix (FRCM) materials for the strengthening of reinforced concrete (RC) beams is experimentally investigated. Bending tests on RC beams strengthened with different FRCM materials, made out of (1)?carbon fiber nets; and (2)?poliparafenilenbenzobisoxazole (PBO) fiber nets embedded in cement-based matrix, are performed. For case (2), different net shapes, cementitious matrices, and a number of net layers were considered. Depending on the type of fibers and matrix, different flexural debonding failure modes are identified. The fiber strain at debonding is evaluated by comparing the experimental results with those obtained with two different theoretical models. The results obtained in this study confirm the effectiveness of FRCM materials for the strengthening of RC structures and encourage further experimental and theoretical work on the topic. A better understanding of the debonding phenomenon is crucial for an optimal design of the strengthening material. The way in which the nature of fibers and matrices and the number of layers control the performance of the strengthened members is also investigated in the present paper.     

Prediction Models for Debonding Failure Loads of Carbon Fiber Reinforced Polymer Retrofitted Reinforced Concrete Beams

This study focuses on debonding failure in reinforced concrete beams with carbon fiber reinforced polymer composite bonded on the soffit using the wet lay-up method. An experimental study, which involved 26 tests, was carried out. The experiments showed two failure modes: Intermediate span debond and end debond. The first failure is the result of the high bond stress near the tip of a flexure-shear crack, whereas the second type of failure is due to the high shear stress developed in the weakest concrete layer at the tension reinforcement level. The experiments have shown that U-straps can be effective in preventing intermediate span and end debond. Based on experimental observations, two simple and practical theoretical models were developed and verified with the experimental data, together with a large database of other existing tests.     

Repair of Cracked Steel Girders Connected to Concrete Slabs Using Carbon-Fiber-Reinforced Polymer Sheets

This paper presents the results of an experimental study on the repair of artificially damaged steel–concrete composite beams repaired using adhesively bonded carbon-fiber-reinforced polymer (CFRP) sheets. Eleven, 2 m long, beams composed of W150×22 steel sections with 465×75?mm concrete slabs were tested in four-point bending. Severe damage was first introduced in ten beams by saw cutting the tension flange completely at mid span, to simulate a fatigue crack or a localized severe corrosion. Standard modulus (SM) and high modulus (HM) CFRP sheets were then used to repair nine damaged beams. The length and number of CFRP layers applied to the cracked flange on the underside, or on both sides, were varied. Results showed that the damage had reduced flexural strength and stiffness by 60 and 54%, respectively. Nevertheless, CFRP-repaired beams achieved various levels of recovery, and in some cases, exceeded the original capacities. The strength of beams repaired with sheets, ranging in length from 8 to 97% of the span, varied from 46–116% of the original undamaged strength, whereas the stiffness range was 86–126% of original stiffness. SM-CFRP failed by debonding whereas HM-CFRP was ruptured. Bonding the sheets to both sides of the flange was not very advantageous over bonding to the underside only.     

Fatigue of Concrete Beams Strengthened with Glass-Fiber Composite under Flexure

A detailed investigation on the fatigue performance of concrete beams strengthened with glass-fiber composite (GFC) is performed in this study. Cyclic load tests were conducted on reinforced concrete beam specimens strengthened with two layers of GFC bonded to the beams’ bottom surface using a special epoxy resin. Midspan-deflection and cracks were measured at different numbers of load cycles and varying fatigue loading levels during the tests. Investigated parameters include total midspan-deflection, residual midspan-deflection after unloading, crack width, crack length, and crack distribution at different loading stages. The fatigue performance of concrete beams strengthened with GFC was evaluated by comparing the deflections, crack sizes, and crack distributions with unstrengthened beams. The concrete beams strengthened with GFC investigated in this study showed significant improvement on fatigue performance.     

Flexural Strengthening of RC Beams with Externally Bonded CFRP Systems: Test Results and 3D Nonlinear FE Analysis

This paper presents experimental results and a numerical analysis of the reinforced concrete (RC) beams strengthened in flexure with various externally bonded carbon fiber-reinforced polymer (CFRP) configurations. The aim of the experimental work was to investigate the parameters that may delay the intermediate crack debonding of the bottom CFRP laminate, and increase the load carrying capacity and CFRP strength utilization ratio. Ten rectangular RC specimens with a clear span of 4.2?m, categorized in two series, were tested to evaluate the effect of using the additional U-shaped CFRP systems on the intermediate crack debonding of the bottom laminate. Two different configurations of the additional systems were proposed, namely, continuous U-shaped wet layup sheets and spaced side-bonded CFRP L-shaped laminates. The fiber orientation effect of the side-bonded sheets was also investigated. A numerical analysis using an incremental nonlinear displacement-controlled 3D finite-element (FE) model was developed to investigate the flexural and CFRP/concrete interfacial responses of the tested beams. The finite-element model accounts for the orthotropic behavior of the CFRP laminates. An appropriate bond-slip model was adopted to characterize the behavior of the CFRP/concrete interface. Comparisons between the FE predictions and experimental results show very good agreement in terms of the load-deflection and load-strain relationships, ultimate capacities, and failure modes of the beams.     

Full Torsional Behavior of RC Beams Wrapped with FRP: Analytical Model

Torsion failure is an undesirable brittle form of failure. Although previous experimental studies have shown that using fiber-reinforced polymer (FRP) sheets for torsion strengthening of reinforced concrete (RC) beams is an effective solution in many situations, very few analytical models are available for predicting the section capacity. None of these models predicted the full behavior of RC beams wrapped with FRP, account for the fact that the FRP is not bonded to all beam faces, or predicted the ultimate FRP strain using equations developed based on testing FRP strengthened beams in torsion. In this paper, an analytical model was developed for the case of the RC beams strengthened in torsion. The model is based on the basics of the modified compression field theory, the hollow tube analogy, and the compatibility at the corner of the cross section. Several modifications were implemented to be able to take into account the effect of various parameters including various strengthening schemes where the FRP is not bonded to all beam faces, FRP contribution, and different failure modes. The model showed good agreement with the experimental results. The model predicted the strength more accurately than a previous model, which will be discussed later. The model predicted the FRP strain and the failure mode.