Investigation on textural and structural evolution of the novel crack-free equimolar Al2O3-SiO2-TiO2 ternary aerogel during thermal treatment

Crack-free mesoporous equimolar Al₂O₃-SiO₂-TiO₂ ternary nanocomposite aerogel has been synthesized using an ethanol supercritical drying technique. The effects of heat treatment temperatures on its textural and structural evolution during thermal treatment are investigated in this study. XRD results reveal that only anatase phase is detected in the as-dried ternary aerogel, whereas peaks corresponding to silica and alumina phase are not shown due to its much faster polymerization rate of titania precursor. Structural transition from boehmite to γ-Al₂O₃ begins to occur at 450 °C within the ternary aerogel, and this process is completed at nearly 615 °C. The needle-like reticulated γ-Al₂O₃ grows along the anatase backbone, however, it is not evident in the XRD patterns. The morphologies of the ternary aerogel become more homogeneous after the structural transition, as indicated by the SEM analysis, which is also consistent with the BET results. With the increase of heat temperature up to 1050 °C, the γ-Al₂O₃ phase disappears and no separate SiO₂ is detected. At the same time, the silica-alumina network originates in a structure of Al-O-Si, and the silicon atoms incorporate into the alumina phase in the γ-Al₂O₃ structure, disordering the alumina primary particles. When the heat treatment temperature increases to 1200 °C, mullitization begins to occur along the titania backbone, whereas silica crystallization happens at 1300 °C. The 600 °C calcinated ternary aerogel is typically mesoporous, showing high specific surface area (255.37 m²/g), suitable average pore diameter (22.83 nm) and large pore volume (1.34 cm³/g). Moreover, the ternary aerogels show high surface acid activity at temperatures below 1000 °C, which have future applications for ideal catalysts and catalyst supports at elevated temperatures.     

Combustion synthesis of mullite–titanium boride composite

Mullite/TiB₂ composite has been prepared successfully by combustion synthesis from blends of fine TiO₂–B₂O₃–Al–SiO₂ powders. Despite the dilution effect due to silica addition and the endothermic character of mullite formation reaction, thermodynamic calculation shows that the overall reaction between the reactants is still highly exothermic. Depending on the silica grain size and the preheating temperature, partial to full conversion of reactants into products can be achieved during the process. At 550 °C preheating temperature, complete conversion of the reactants to mullite/TiB₂ was achieved. Adiabatic combustion temperature and mullite molten fraction are calculated as a function of preheating temperature.     

Fabrication of cylindrical SiCf/Si/SiC-based composite by electrophoretic deposition and liquid silicon infiltration

Cylindrical SiC-based composites composed of inner Si/SiC reticulated foam and outer Si-infiltrated SiC fiber-reinforced SiC (SiC_f/Si/SiC) skin were fabricated by the electrophoretic deposition of matrix particles into SiC fabrics followed by Si-infiltration for high temperature heat exchanger applications. An electrophoretic deposition combined with ultrasonication was used to fabricate a tubular SiC_f/SiC skin layer, which infiltrated SiC and carbon particles effectively into the voids of SiC fabrics by minimizing the surface sealing effect. After liquid silicon infiltration at 1550 °C, the composite revealed a density of 2.75 g/cm³ along with a well-joined interface between the inside Si/SiC foam and outer SiC_f/Si/SiC skin layer. The results also showed that the skin layer, which was composed of 81.4 wt% β-SiC, 17.2 wt% Si and 1.4 wt% SiO₂, exhibited a gastight dense microstructure and the flexural strength of 192.3 MPa.     

Diphasic aluminosilicate gels with two stage mullitization in temperature range of 1200–1300 °C

The crystallization of mullite in amorphous diphasic gel aged for 6 months has been studied using non-isothermal differential scanning calorimetry (DSC) and powder X-ray diffraction with Rietveld structure refinement analysis. The diphasic premullite gels undergo structural changes by aging even when they are calcined at 700 °C. These changes imply segregation of the sample to Al₂O₃-rich and SiO₂-rich regions. From the Al₂O₃-rich region crystallizes poorly defined AlSi spinel at 977 °C followed by two-step mullite crystallization in the temperature interval of 1200–1300 °C. Two overlapped exothermic peaks on DSC scan of aged gel were observed; the first at 1233 °C and the second at 1261 °C. The former is attributed to mullite crystallization by transformation of AlSi spinel, by which excess alumina occurs, which in the second step of mullitization reacts with amorphous SiO₂-rich phase. The activation energy for mullite crystallization in the first step was E_a=935±14 kJ mol⁻¹ and the Avrami exponent n=2.5. The values E_a=1119±25 kJ mol⁻¹ and n=1.2 were obtained for mullite formation in the second step. If amorphous SiO₂-rich phase is extracted from the sample, the value E_a=805±26 kJ mol⁻¹ is obtained. Mullite crystallizing from AlSi spinel (when SiO₂-rich phase has been extracted) differentiates compositionally from that formed by both reactions. Smaller unit cell parameters and higher amount of oxygen vacancies are incorporated into tetrahedral positions of mullite structure, as was determined by Rietveld structure refinement method.     

Improvement of the mechanical properties of SiC reticulated porous ceramics with optimized three-layered struts for porous media combustion

Silicon carbide reticulated porous ceramics (SiC RPCs) with three-layered struts were fabricated by polymer replica method, followed by infiltrating alumina slurries containing silicon (slurry-Si) and andalusite (slurry-An), respectively. The effects of composition of infiltration slurries on the strut structure, mechanical properties and thermal shock resistance of SiC RPCs were investigated. The results showed that the SiC RPCs infiltrated with slurry-Si and slurry-An exhibited better mechanical properties and thermal shock resistance in comparison with those of alumina slurry infiltration, even obtained the considerable strength at 1300 °C. In slurry-Si, silicon was oxidized into SiO₂ in the temperature range from 1300 °C to 1400 °C and it reacted with Al₂O₃ into mullite phase at 1450 °C. Meantime, the addition of silicon in slurry-Si could reduce SiC oxidation of SiC RPCs during firing process in contrast with alumina slurry. With regard to slurry-An, andalusite started to transform into mullite phase at 1300 °C and the secondary mullitization occurred at 1450 °C. The enhanced mechanical properties and thermal shock resistance of SiC RPCs infiltrated alumina slurries containing silicon and andalusite were attributed to the optimized microstructure and the triangular zone (inner layer of strut) with mullite bonded corundum via reaction sintering. In addition, the generation of residual compressive stress together with better interlocked needle-like mullite led to the crack-deflection in SiC skeleton, thus improving the thermal shock resistance of obtained SiC RPCs.     

Mechanical properties of nano-grain SiO2 glass prepared by spark plasma sintering

Silicon carbide (SiC) layers were deposited on silica (SiO₂) glass powder by rotary chemical vapor deposition (RCVD) to form SiO₂ glass (core)/SiC (shell) powder; this powder was consolidated by spark plasma sintering (SPS). SiO₂ glass powder with a particle size of 250 nm was coated with 5–10-nm-thick SiC layers. The resultant SiO₂ glass (core)/SiC (shell) powder was consolidated to form a nano-grain SiO₂ glass composite at a relative density above 90% by SPS in the sintering temperature range of 1573–1823 K. The Vickers hardness and fracture toughness of the SiO₂ glass composite at 1723 K were found to be 14.2 GPa and 5.4 MPa m^1/2, respectively.     

Influences of quartz and muscovite on the formation of mullite from kaolinite

A kaolin containing muscovite and quartz (K-SZ) and a pure kaolin (K-SX) with the addition of potassium feldspar, K₂SO₄ and quartz, respectively, were used to investigate the influences of muscovite and quartz on the formation of mullite from kaolinite in the temperature range 1000–1500 °C. In K-SZ formation of mullite began at 1100 °C, and in K-SX at 1000 °C. In K-SZ quartz accelerated the formation of cristobalite and restrained the reaction of mullite and silica. Muscovite in K-SZ acted as a fluxing agent for silica and mullite before 1400 °C and accelerated the formation of cristobalite. The FTIR band at 896.8 cm^− 1 was used to monitor the formation of orthorhombic mullite.     

Facile synthesis of SiOx spheres or dumbbell-shaped β-SiC whiskers on expanded graphite by silicon vapor deposition

A facile method was developed to synthesize SiO_x spheres or dumbbell-shaped β-SiC whiskers on expanded graphite (SiO_x/EG or β-SiC/EG) by silicon vapor deposition without catalyst. With the carbon black atmosphere, the above hybrids were synthesized above 1100 °C in a graphite crucible where silicon powder was placed under the expanded graphite (EG). The growth of SiO_x spheres is controlled by vapor-solid mechanism at 1100 °C and 1200 °C. Namely, the active carbon atoms absorbed SiO (g) and Si (g) to form SiC nuclei. Then, the SiO₂, residual SiO (g) and Si (g) deposited on SiC nuclei to form SiO_x spheres. At 1300 °C and 1400 °C, the same SiO_x spheres formed on EG as well as many dumbbell-shaped β-SiC whiskers. The growth of dumbbell-shaped β-SiC whiskers is controlled by vapor-vapor and vapor-solid mechanism successively. In a word, firstly, the β-SiC whiskers with defects formed via the reaction between Si (g) and CO (g). After that, the SiO₂, residual SiO (g) and residual Si (g) preferentially deposited on defects, then deposited on other parts of β-SiC whiskers to form dumbbell-shaped SiC whiskers.     

Enhancement of bonding network for silica sol bonded SiC castables by reactive micropowder

Silica sol bonded castables have obvious advantages over low cement or hydratable alumina bonded castables in drying performance and sintering properties for SiC castables. However, they are not widely used due to their weak strength at low temperature. The efficiency of bonding network for silica sol bonded SiC castable in the presence of different reactive micropowder such as SiO₂ micropowder and α-Al₂O₃ micropowder was evaluated through oscillatory tests, sintered properties and microstructural analysis. Results show that the polymerization reaction between SiO₂ micropowders enhanced the siloxane network and reinforced the bonding strength, furthermore, the addition of α-Al₂O₃ micropowder contributed to accelerating the formation of the siloxane network and hardening of the silica sol at lower temperatures and shorter time. Silica sol performed well as a binder agent for SiC castables with an addition content of 3 wt% SiO₂ micropowder and 2 wt% α-Al₂O₃ micropowder, which showed high strength and good workability at room temperature. And Silica sol bonded SiC castable with the above micropowder contents possessed the best mechanical behavior after heat treatment due to combined binding of SiC whiskers and mullite.     

Ablation resistance of HfB2-SiC coating prepared by in-situ reaction method for SiC coated C/C composites

To improve the ablation resistance of SiC coating, HfB₂-SiC coating was prepared on SiC-coated carbon/carbon (C/C) composites by in-situ reaction method. Owing to the penetration of coating powders, there is no clear boundary between SiC coating and HfB₂-SiC coating. After oxyacetylene ablation for 60 s at heat flux of 2400 kW/m², the mass ablation rate and linear ablation rate of the coated C/C composites were only 0.147 mg/s and 0.267 µm/s, reduced by 21.8% and 60.0%, respectively, compared with SiC coated C/C composites. The good ablation resistance was attributed to the formation of multiple Hf-Si-O glassy layer including SiO₂, HfO₂ and HfSiO₄.     

The properties of silica aerogels hybridized with SiO2 nanoparticles by ambient pressure drying

In this study, we report the chemical characteristics of silica aerogels that were produced by adding SiO₂ nanoparticles into silica aerogel by ambient pressure drying. We synthesized silica aerogel composites with different weight percentages of SiO₂ nanoparticles ranging from 0 wt% to 0.025 wt% of the total amount of solution. As the wt% of SiO₂ nanoparticles increased, the number of chemical bonds that formed during condensation of the silica aerogel increased because of the presence of surface hydroxyl groups, thus the particle size of the silica aerogels increased. Silica nanoparticle-doping of silica aerogels can be used to control the synthesis of nanocomplex structures.     

A mullite/SiC oxidation protective coating for carbon/carbon composites

To protect carbon/carbon (C/C) composites against oxidation, a mullite coating was prepared on SiC precoated C/C composites by a hydrothermal electrophoretic deposition process. The phase composition, microstructure and oxidation resistance of the prepared mullite/SiC coatings were investigated. Results show that hydrothermal electrophoretic deposition is an effective route to achieve crack-free mullite coatings. The mullite/SiC coating displays excellent oxidation resistance and can protect C/C composites from oxidation at 1773 K for 322 h with a weight loss rate of only 4.89 × 10^?4 g/cm² h. The failure of the multi-layer coatings is considered to be caused by the volatilization of silicate glass layer, the formation of microholes and microcracks on the coating surface and the formation of penetrative holes between the SiC bonding layer and the C/C matrix at 1773 K. The corresponding high temperature oxidation activation energy of the coated C/C composites at 1573–1773 K is calculated to be 111.11 kJ/mol.     

Thermal evolution and structural study of 2:1 mullite from monophasic gels

Single phase mullite gels with composition 2Al₂O₃·SiO₂ (2:1) were prepared by the slow hydrolysis method using aluminium nitrate nonahydrate and tetraethylorthosilicate as reagents. The evolution to mullite from gels was studied by infrared (IR) spectroscopy and X-ray diffraction (XRD). Gels thermally treated under fast schedules showed mullite formation below 900 °C. Compositional and microstructural changes in 2:1 mullites through the range of temperature from 900 to 1600 °C were determined by the measurement of lattice parameters and field emission scanning electron microscopy. The alumina-rich mullites formed at low temperatures become almost the nominal 2:1 at 1600 °C. This result is consistent with available thermodynamic data for mullite formation from alumina and silica. Microstructural examination indicated an almost constant grain size for mullite from 900 to 1600 °C.     

Preparation of SiO2–SiC composites with a precursor method

SiO₂–SiC composite particles were prepared through a hybrid sol–gel precursor process. Compacts were prepared by using a conventional sintering process. The techniques of DSC–TG, SEM and XRD were use to characterize the composite particles and the sintered compacts. It was found that a core–shell structure was constructed in the composite particles with cores of SiC and shells of amorphous SiO₂. Nucleation of SiO₂ occurred at about 1200 °C. The optimized sintering temperature for 30SiO₂–70SiC (vol.%) composites was about 1400 °C with a relatively homogeneous microstructure. The maximum density was about 2.03 g cm^?3.     

Plasma spray deposition of tri-layer environmental barrier coatings

An air plasma spray process has been used to deposit tri-layer environmental barrier coatings consisting of a silicon bond coat, a mullite inter-diffusion barrier, and a Yb₂SiO₅ top coat on SiC substrates. Solidified droplets in as-deposited Yb₂SiO₅ and mullite layers were discovered to be depleted in silicon. This led to the formation of an Yb₂SiO₅ + Yb₂O₃ two-phase top coat and 2:1 mullite (2Al₂O₃*SiO₂) coat deposited from 3:2 mullite powder. The compositions were consistent with preferential silicon evaporation during transient plasma heating; a consequence of the high vapor pressure of silicon species at plasma temperatures. Annealing at 1300 °C resulted in internal bond coat oxidation of pore and splat surfaces, precipitation of Yb₂O₃ in the top coat, and transformation of 2:1 mullite to 3:2 mullite + Al₂O₃. Mud-cracks were found in the Yb₂SiO₅ layer and in precipitated Al₂O₃ due to the thermal expansion mismatch between these coating phases and the substrate.     

Preparation and characterization of porous,biomorphic SiC ceramic with hybrid pore structure

Bio-carbon template (charcoal) was prepared by carbonizing pine wood at 1200 °C under vacuum, and was impregnated with phenolic resin/SiO₂ sol mixture by vacuum/pressure processing. Porous SiC ceramics with hybrid pore structure, a combination of tubular pores and network SiC struts in the tubular pores, were fabricated via sol–gel conversion, carbonization and carbothermal reduction reaction at elevated temperatures in Ar atmosphere. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM) were employed to characterize the phase identification and microstructural changes during the C/SiO₂ composites-to-porous SiC ceramic conversion. Experimental results show that the density of C/SiO₂ composite increases with the number of impregnation procedure, and increases from 0.32 g cm⁻³ of pine-derived charcoal to 1.5 g cm⁻³ of C/SiO₂ composite after the sixth impregnation. The conversion degree of charcoal to porous SiC ceramic increases as reaction time is lengthened. The resulting SiC ceramic consists of β-SiC with a small amount of α-SiC. The conversion from pine charcoal to porous SiC ceramic with hybrid pore structure improves bending strength from 16.4 to 42.2 MPa, and decreases porosity from 76.1% to 48.3%.     

Effect of SiC nanowires on the thermal shock resistance of joint between carbon/carbon composites and Li2O–Al2O3–SiO2 glass ceramics

In order to improve the bonding property of joint between SiC modified carbon/carbon (C/C) composites and Li₂O–Al₂O₃–SiO₂ (LAS) glass ceramics, SiC nanowires were attempted as the reinforcement materials in the interface region of SiC transition layer and Li₂O–MgO–Al₂O₃–SiO₂ (LMAS) gradient joining interlayer. The C/C–LAS joint with SiC nanowire-reinforced interface layer was prepared by a three-step technique of pack cementation, in situ reaction and hot-pressing. The microstructure and thermal shock resistance of the as-prepared joints were examined. The average shear strength of the joined samples with SiC nanowires increased from 24.9 MPa to 31.6 MPa after 40 thermal cycles between 1000 °C and room temperature, while that of the joined samples without SiC nanowires dropped from 21.4 MPa to 8.3 MPa. The increase of thermal shock resistance of the C/C–LAS joints was mainly attributed to the toughening mechanism of SiC nanowires by pullout, bridging and crack deflection.     

Lithium insertion into dense and porous carbon-rich polymer-derived SiOC ceramics

Two polymer-derived SiOC ceramics with different amount of carbon were synthesized either as dense or porous SiOC powders. The dense materials were produced up to a maximum temperature of 1400 °C and show a phase separated nanostructure consisting of SiO₂-rich clusters, nanocrystalline SiC and nanocrystalline carbon phase. The corresponding porous materials were obtained by etching the silica phase of the dense SiOC with 20% HF solution. The electrochemical properties of the dense and porous SiOC ceramics in terms of lithium insertion/extraction were studied. Accordingly, the SiOC materials show a first lithium insertion capacity between 380 and 648 mAh g^?1 followed by significantly lower extraction capacities between 102 and 272 mAh g^?1. We consider the free carbon phase present in the ceramic as the major lithium intercalating agent. The porous samples show a stable electrochemical behavior up to 30 cycles while for the dense materials the efficiency drops to almost zero after 10 cycles.     

In-situ fabrication of Al2O3–SiC nanocomposites using B2O3 as sintering aid

Al₂O₃–SiC nanocomposites with 5 and 10 vol% SiC have been in-situ fabricated by sol-gel method followed by carbothermal reduction of alumina–silica gel using B₂O₃ as sintering aid. Green bodies were formed by cold isostatic pressing of calcined gel, which was prepared by an aqueous sol-containing aluminum chloride, TEOS, sucrose and boric acid. Pressureless sintering was carried out in Ar–12%H₂ atmosphere at 1700 °C. Addition of B₂O₃ (1 or 3 wt%) was an effective densification aid in the Al₂O₃–5 vol% SiC composites, while the densification of Al₂O₃–10 vol% SiC composites was not affected by adding B₂O₃. The composite material containing 5 vol% SiC doped with 3 wt% B₂O₃ reached 98.7% of full density. Nano-sized β-SiC particles were formed in-situ by means of a reaction between mullite and carbon at 1600 °C. Scanning electron microscopy revealed that the spherical in-situ synthesized SiC nanoparticles were well distributed through the composite and located predominantly to the interior of alumina matrix grains.     

Synthesis and sintering of pre-mullite powders obtained via carbonate precipitation

Ultrafine pre-mullite powders, which yield mullite at high temperatures, have been prepared from colloidal silica and aluminium nitrate via carbonate coprecipitation and followed by calcination. The chemical and structural evolutions of the as-prepared precipitation powder during thermal treatment were studied and the sinterability of pre-mullite powders were investigated. The as-prepared powders are comprised of ammonium aluminum carbonate hydroxide and amorphous silica, which convert to mullite via the Al–Si spinel phase at 1250 °C. Calcination of the as-prepared powders at 1000 °C gives a very active powder which can be reactively sintered to 98.2% theoretical density at 1550 °C. The sintered body possesses a relatively uniform chemical composition with Al₂O₃/SiO₂ mole ratio of 1.48 and exhibits a very fine interlocking equiaxed and polygonal grain morphology with grain size of 100–200 nm.