Amorphisation of ZnAl2O4 spinel under heavy ion irradiation

ZnAl₂O₄ spinels have been irradiated with several ions (Ne, S, Kr and Xe) at the IRRSUD beamline of the GANIL facility, in order to determine irradiation conditions (stopping power, fluence) for amorphisation. We observed by transmission electron microscopy (TEM) that with Xe ions at 92 MeV, individual ion tracks are still crystalline, whereas an amorphisation starts below a fluence of 5 × 10¹² cm⁻² up to a total amorphisation between 1 × 10¹³ and 1 × 10¹⁴ cm⁻². The coexistence of amorphous and crystalline domains in the same pristine grain is clearly visible in the TEM images. All the crystalline domains remain close to the same orientation as the original grain. According to TEM and X-ray Diffraction (XRD) results, the stopping power threshold for amorphisation is between 9 and 12 keV nm⁻¹.     

Anisotropic deformation of polystyrene particles by MeV Au ion irradiation

MeV Au irradiation leads to a shape change of polystyrene (PS) and SiO₂ particles from spherical to ellipsoidal, with an aspect ratio that can be precisely controlled by the ion fluence. Sub-micrometer PS and SiO₂ particles were deposited on copper substrates and irradiated with Au ions at 230 K, using an ion energy and fluence ranging from 2 to 10 MeV and 1 × 10¹⁴ ions/cm² to 1 × 10¹⁵ ions/cm². The mechanisms of anisotropic deformation of PS and SiO₂ particles are different because of their distinct physical and chemical properties. At the start of irradiation, the volume of PS particles decrease, then the aspect ratio increases with fluence, whereas for SiO₂ particles the volume remains constant.     

Effect of swift heavy ion irradiation on nanocrystalline CaS:Bi phosphors: Structural, optical and luminescence studies

Luminescence studies of CaS:Bi nanocrystalline phosphors synthesized by wet chemical co-precipitation method and irradiated with swift heavy ions (i.e. O⁷⁺-ion with 100 MeV and Ag¹⁵⁺-ion with 200 MeV) have been carried out. The samples have been irradiated at different ion fluences in the range 1 × 10¹²-1 × 10¹³ ions/cm². The average grain size of the samples before irradiation was estimated as 35 nm using line broadening of XRD (X-ray diffraction) peaks and TEM (transmission electron microscope) studies. Our results suggest a good structural stability of CaS:Bi against swift heavy ion irradiation. The blue emission band of CaS:Bi³⁺ nanophosphor at 401 nm is from the transition ³P₁ → ¹S₀ of the Bi³⁺. We have observed a decrease in lattice constant (a) and increase of optical energy band gap after ion irradiation. We presume this change due to grain fragmentation by dense electronic excitation induced by swift heavy ion. We have studied the optical and luminescent behavior of the samples by changing the ion energy and also by changing dopant concentration from 0.01 mol% to 0.10 mol%. It has been examined that ion irradiation enhanced the luminescence of the samples.     

Effect of swift heavy ion irradiation on structure, optical, and gas sensing properties of SnO2 thin films

Swift heavy ion irradiation has been successfully used to modify the structural, optical, and gas sensing properties of SnO₂ thin films. The SnO₂ thin films prepared by sol-gel process were irradiated with 75 MeV Ni⁺ beam at fluences ranging from 1 × 10¹¹ ion/cm² to 3 × 10¹³ ion/cm². Structural characterization with glancing angle X-ray diffraction shows an enhancement of crystallinity and systematic change of stress in the SnO₂ lattice up to a threshold value of 1 × 10¹³ ions/cm², but decrease in crystallinity at highest fluence of 3 × 10¹³ ions/cm². Microstructure investigation of the irradiated films by transmission electron microscopy supports the XRD observations. Optical properties studied by absorption and PL spectroscopies reveal a red shift of the band gap from 3.75 eV to 3.1 eV, and a broad yellow luminescence, respectively, with increase in ion fluence. Gas response of the irradiated SnO₂ films shows increase of resistance on exposure to ammonia (NH₃), indicating p-type conductivity resulting from ion irradiation.     

Swift heavy ion induced modifications of fullerene C70 thin films

Modifications of the C₇₀ molecule (fullerene) under swift heavy ion irradiation are investigated. C₇₀ thin films were irradiated with 120 MeV Au ions at fluences from 1 × 10¹² to 3 × 10¹³ ions/cm². The energetic ion impacts lead to the destruction of the C₇₀ molecule. To investigate the stability of C₇₀ fullerene, the damage cross-section and radius of the damaged cylindrical zones are evaluated by fitting the evanescence of C₇₀ vibration modes recorded by Raman spectroscopy. Conductivity measurements together with Raman and optical absorption studies revealed that an irradiation fluence of 3 × 10¹³ ions/cm² results in complete amorphization of the carbon structure of the fullerene molecules.     

10 MeV Au ion irradiation effects in an MgO-HfO2 ceramic-ceramic (CERCER) composite

Room temperature ion irradiation damage studies were performed on a ceramic composite intended to emulate a dispersion nuclear fuel. The composite is composed of 90-mole% MgO and 10-mole% HfO₂. The as-synthesized composite was found to consist of Mg₂Hf₅O₁₂ (and some residual HfO₂) particles embedded in an MgO matrix. X-ray diffraction revealed that nearly all of the initial HfO₂ reacted with some MgO to form Mg₂Hf₅O₁₂. Ion irradiations were performed using 10 MeV Au³⁺ ions at room temperature over a fluence range of 5 × 10¹⁶-5 × 10²⁰ Au/m². Irradiated samples were characterized using both grazing incidence X-ray diffraction (GIXRD) and transmission electron microscopy (TEM), the latter using both selected-area electron diffraction (SAED) and micro-diffraction (μD) on samples prepared in cross-sectional geometry. Both GIXRD and TEM electron diffraction measurements on a specimen irradiated to a fluence of 5 × 10²⁰ Au/cm², revealed that the initial rhombohedral Mg₂Hf₅O₁₂ phase was transformed into a cubic-Mg₂Hf₅O₁₂ phase. Finally, it is important to note that at the highest ion fluence used in this investigation (5 × 10²⁰ Au/m²), both the MgO matrix and the Mg₂Hf₅O₁₂ second phase remained crystalline.     

Light ion irradiation-induced phase transformation in the monoclinic polymorph of zirconia

Ion irradiation damage experiments were performed at ∼80 K on polycrystalline samples of monoclinic, slightly sub-stoichiometric zirconia (ZrO_1.98). Following irradiation with 150 keV Ne⁺ ions, the monoclinic phase was gradually replaced by a new phase. Transmission electron microscopy (TEM) observations in cross-sectional geometry and electron microdiffraction (μD) measurements revealed that the irradiated layer in a sample irradiated to a fluence of 5 × 10²⁰ Ne/m² is partially transformed to a higher symmetry phase of high crystallinity. This phase transformation is accompanied by reduction of the initial micron-sized, highly-twinned grain distribution, to a nano-phased grain structure. Grazing incidence X-ray diffraction (GIXRD) measurements revealed that the radiation-induced phase is a tetragonal polymorph of zirconia. This was verified by the existence of strong (1 0 1) diffraction maxima and weak (1 0 2) reflections (body-centered cell). Raman spectroscopy (RS) measurements were also performed in an attempt to corroborate GIXRD results obtained from the irradiated material. RS measurements in the confocal geometry agreed with GIXRD measurements, although RS was not as definitive as GIXRD. In addition to RS showing the existence of a band corresponding to a tetragonal structure at 262 cm⁻¹, a new mystery band appeared at 702 cm⁻¹ that increased in intensity as a function of irradiation fluence.     

Structural and optical study of irradiation effect in GaN epilayers induced by 308 MeV Xe ions

Wurtzite GaN epilayers irradiated at room temperature with 308 MeV ¹²⁹Xe³⁵⁺ ions to fluences of 1 × 10¹³ and 3 × 10¹³ cm⁻² have been studied by contact mode atomic force microscopy (AFM), high-resolution X-ray diffraction (HRXRD), micro-Raman scattering and photoluminescence (PL) spectroscopy. The AFM images showed that the surface of GaN films was etched efficiently due to the Xe ion irradiation. The initial step-terrace structure on GaN surface was eliminated completely at a fluence of 3 × 10¹³ cm⁻². HRXRD and Raman results indicated that the Xe ion irradiation led to a homogenous lattice expansion throughout the entire ∼3 μm-thick GaN films. The lattice expansion as well as the biaxial compressive stress of the films was increasing with the increase of ion fluence. PL measurements showed that a dominant yellow luminescence band in the as-grown GaN films disappeared, but a blue and a green luminescence bands were produced after irradiation. Based on these results, the strong electronic excitation effect of 308 MeV Xe ions in GaN is discussed.     

Mixing of Cr and Si atoms induced by noble gas ions irradiation of Cr/Si bilayers

Cr/Si bilayers were irradiated at room temperature with 120 keV Ar, 140 keV Kr and 350 keV Xe ions to fluences ranging from 10¹⁵ to 2 × 10¹⁶ ions/cm². The thickness of Cr layer evaporated on Si substrate was about 400 Å. Rutherford backscattering spectrometry (RBS) was used to investigate the atomic mixing induced at the Cr-Si interface as function of the incident ion mass and fluence. We observed that for the samples irradiated with Ar ions, RBS yields from both Cr layer and Si substrate are the same as before the irradiation. There is no mixing of Cr and Si atoms, even at the fluence of 2 × 10¹⁶ ions/cm². For the samples irradiated with Kr ions, a slight broadening of the Cr and Si interfacial edges was produced from the fluence of 5 × 10¹⁵ ions/cm². The broadening of the Cr and Si interfacial edges is more pronounced with Xe ions particularly to the fluence of 10¹⁶ ions/cm². The interface broadening was found to depend linearly on the ion fluence and suggests that the mixing is like a diffusion controlled process. The experimental mixing rates were determined and compared with values predicted by ballistic and thermal spike models. Our experimental data were well reproduced by the thermal spikes model.     

Oxygen ion irradiation effect on corrosion behavior of titanium in nitric acid medium

The corrosion assessment and surface layer properties after O⁵⁺ ion irradiation of commercially pure titanium (CP-Ti) has been studied in 11.5 N HNO₃. CP-Ti specimen was irradiated at different fluences of 1 × 10¹³, 1 × 10¹⁴ and 1 × 10¹⁵ ions/cm² below 313 K, using 116 MeV O⁵⁺ ions source. The corrosion resistance and surface layer were evaluated by using potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and glancing-angle X-ray diffraction (GXRD) methods. The potentiodynamic anodic polarization results of CP-Ti revealed that increased in ion fluence (1 × 10¹³-1 × 10¹⁵ ions/cm²) resulted in increased passive current density due to higher anodic dissolution. SEM micrographs and GXRD analysis corroborated these results showing irradiation damage after corrosion test and modified oxide layer by O⁵⁺ ion irradiation was observed. The EIS studies revealed that the stability and passive film resistance varied depending on the fluence of ion irradiation. The GXRD patterns of O⁵⁺ ion irradiated CP-Ti revealed the oxides formed are mostly TiO₂, Ti₂O₃ and TiO. In this paper, the effects of O⁵⁺ ion irradiation on material integrity and corrosion behavior of CP-Ti in nitric acid are described.     

Evidence of nanostructure formation in Ge oxide by crystallization induced by swift heavy ion irradiation

Ge oxide films were irradiated with 150 MeV Ag ions at fluences varying between 10¹² and 10¹⁴ ions/cm². The irradiation-induced changes were monitored by FT-IR spectroscopy, atomic force microscopy, X-ray diffraction and photoluminescence spectroscopy. The FT-IR spectra indicate stoichiometric changes and an increase in Ge content on irradiation. X-ray diffraction shows a crystallization of the irradiated films and presence of both Ge and GeO₂ phases. The Ge nanocrystal size, as calculated from Scherrer’s formula, was around 30 nm. The morphological changes, observed in atomic force microscopy, also indicate formation of nanostructures upon ion irradiation and a uniform growth is observed for a fluence of 1 × 10¹⁴ ions/cm².     

Swift heavy ion induced phase transition in CdTe films deposited by spray pyrolysis in presence of electric field

CdTe polycrystalline thin films possessing hexagonal phase regions are obtained by spray deposition in presence of a high electric field. Thin film samples are irradiated with 100 MeV Ag ions using Pelletron accelerator to study the swift heavy ion induced effects. The ion irradiation results in the transformation of the metastable hexagonal regions in the films to stable cubic phase due to the dense electronic excitations induced by beam irradiation. The phase transformation is seen from the X-ray diffraction patterns. The band gap of the CdTe film changes marginally due to ion irradiation induced phase transformation. The value changes from 1.47 eV for the as deposited sample to 1.44 eV for the sample irradiated at the fluence 1×10¹³ ions/cm². The AFM images show a gradual change in the shape of the particles from rod shape to nearly spherical ones after irradiation.     

Investigations on the effect of 100 MeV Ni ions irradiated chloride vapour phase epitaxy (Cl-VPE) grown GaN epilayers

Gallium nitride (GaN) epilayers have been grown by chloride vapour phase epitaxy (Cl-VPE) technique and the grown GaN layers were irradiated with 100 MeV Ni ions at the fluences of 5 × 10¹² and 2 × 10¹³ ions/cm². The pristine and 100 MeV Ni ions irradiated GaN samples were characterized using X-ray diffraction (XRD), UV-visible transmittance spectrum, photoluminescence (PL) and atomic force microscopy (AFM) analysis. XRD results indicate the presence of gallium oxide phases after Ni ion irradiation, increase in the FWHM and decrease in the intensity of the GaN (0 0 0 2) peak with increasing ion fluences. The UV-visible transmittance spectrum and PL measurements show decrease in the band gap value after irradiation. AFM images show the nanocluster formation upon irradiation and the roughness value of GaN increases with increasing ion fluences.     

Xenon-ion irradiation of Co/Si bilayers: Effects of interface structure and ion energy

Heavy-ion irradiation of ferromagnetic thin layers changes their micromagnetic and microstructural properties, due to the production of defects, relaxation or build-up of stress, or changes of grain size. When the ion range exceeds the layer thickness, ion mixing processes take place, leading to the formation of silicide phases. The present study deals with Co(30 or 55 nm)/Si bilayers irradiated at room temperature with 100- or 200 keV Xe ions to fluences of up to 15 × 10¹⁵/cm². The Si(1 0 0) wafers were either crystalline or pre-amorphized by 1 keV Ar⁺ implantation. Rutherford backscattering spectroscopy, in-plane magneto-optical Kerr effect, and X-ray diffraction served to analyse the samples before and after irradiation. The results will be compared with those obtained for other heavy-ions for Co/Si bilayers and in similar studies on Fe/Si bilayers.     

Study on the behavior of oxygen atoms in swift heavy ion irradiated CeO2 by means of synchrotron radiation X-ray photoelectron spectroscopy

To study the effects of swift heavy ion irradiation on cerium dioxide (CeO₂), CeO₂ sintered pellets were irradiated with 200 MeV Xe ions at room temperature. For irradiated and unirradiated samples, the spectra of X-ray photoelectron spectroscopy (XPS) were measured. XPS spectra for the irradiated samples show that the valence state of Ce atoms partly changes from +4 to +3. The amount of Ce³⁺ state was quantitatively obtained as a function of ion-fluence. The relative amount of oxygen atom displacements, which are accompanied by the decrease in Ce valence state, is 3-5%. This value is too large to be explained in terms of elastic interactions between CeO₂ and 200 MeV ions. The experimental result suggests the contribution of 200 MeV Xe induced electronic excitation to the displacements of oxygen atoms.     

Temperature-dependent surface modification of InSb(0 0 1) crystal by low-energy ion bombardment

Structural and compositional modification of InSb(0 0 1) single crystal surfaces induced by oblique incidence 2-5 keV Ar and Xe ion irradiation have been investigated by means of scanning tunneling and atomic force microscopies, and time-of-flight mass spectroscopy of secondary ion emission. In general, ion-induced patterns (networks of nanowires, or ripples) are angle of incidence- and fluence-dependent. Temperature dependences (from 300 to 600 K) of the RMS roughness and of the ripple wavelength have been determined for the samples bombarded with various fluences. Secondary ion emission from an InSb(0 0 1) surface exposed to 4.5 keV Ar⁺ ions has been investigated with a linear TOF spectrometer working in a static mode. Mass spectra of the sputtered In⁺, Sb⁺ and In₂⁺ secondary ions have been measured both for the non-bombarded (0 0 1) surface and for the surface previously exposed to a fluence of 10¹⁶ ions/cm². In⁺ and In₂⁺ intensities for the irradiated sample are much higher in comparison to the non-bombarded one, whereas Sb⁺ ions show a reversed tendency. This behavior suggests a significant In-enrichment at the InSb(0 0 1) surface caused by the ion bombardment.     

Ag/Fe:TiO2 nano-catalysts prepared by Fe ion implantation and Ag nanoparticle deposition by electron beam irradiation

TiO₂ nano-catalysts made by the sol-gel method were modified by ion implantation and electron beam irradiation to obtain a more efficient photocatalytic function. The results of photodegradation of methyl orange in aqueous solution demonstrate firstly that the films have a photocatalytic activity which responds to visible light. Secondly, it demonstrates that under ultraviolet excitation the sample with a fluence of 6 × 10¹⁵ ions/cm² and electron beam irradiated with concentration of AgNO₃ aqueous solution at 1 × 10⁻³ M gives a more efficient photodegradation ability than pure TiO₂ film and other Fe-doped films display almost the same photodegradation ability as TiO₂ film. Thirdly it demonstrates that under sunlight, all modified films exhibit more photodegradation activity than TiO₂ film.     

Effect of ion beam irradiation on magnetic and structural properties of Pt/Cr/Co multilayers

This paper discusses the effect of ion beam irradiation on the magnetic and structural properties of Pt/Cr/Co multilayers. We observe Co-Cr-Pt ternary alloy phase formation in 1 MeV N⁺ ion irradiated [Pt (2.5 nm)/Cr (0.8 nm)/Co (3.0 nm)]_×6/Si multilayers for a fluence of 1 × 10¹⁶ ions cm⁻² and beyond. The observed phase formation is accompanied by an enhancement in the average grain size, surface roughness and coercivity. Monte Carlo simulation has been performed to study ion-induced defect evolution and atomic displacements to correlate the above observed effects.     

Ion irradiation damage effects in δ-phase Y6W1O12

Polycrystalline Y₆W₁O₁₂ samples were irradiated with 280 keV Kr²⁺ ions to fluences up to 2 × 10²⁰ ions/m² at cryogenic temperature (100 K). Ion irradiation damage effects in these samples were examined using grazing incidence X-ray diffraction (GIXRD) and cross-sectional transmission electron microscopy (TEM). The pristine Y₆W₁O₁₂ possesses rhombohedral symmetry (structure known as the δ-phase), which is closely related to cubic fluorite structure. GIXRD and TEM observations revealed that the irradiated Y₆W₁O₁₂ experiences an ordered rhombohedral to disordered cubic fluorite transformation by a displacement damage dose of ∼12 displacements per atom (dpa). At the highest experimental dose of ∼50 dpa, the uppermost irradiated region was found to be partially amorphous while the buried damage region was found to contain the same fluorite structure as observed at lower dose.     

Ion beam induced modifications in electron beam evaporated aluminum oxide thin films

Al₂O₃ thin films find wide applications in optoelectronics, sensors, tribology etc. In the present work, Al₂O₃ films prepared by electron beam evaporation technique are irradiated with 100 MeV swift Si⁷⁺ ions for the fluence in the range 1 × 10¹² to 1 × 10¹³ ions cm⁻² and the structural properties are studied by glancing angle X-ray diffraction. It shows a single diffraction peak at 38.2° which indicates the γ-phase of Al₂O₃. Further, it is observed that as the fluence increases up to 1 × 10¹³ ions cm⁻² the diffraction peak intensity decreases indicating amorphization. Surface morphology studies by atomic force microscopy show mean surface roughness of 34.73 nm and it decreases with increase in ion fluence. A strong photoluminescence (PL) emission with peak at 442 nm along with shoulder at 420 nm is observed when the samples are excited with 326 nm light. The PL emission is found to increase with increase in ion fluence and the results are discussed in detail.