用X射线衍射分峰法研究固相热处理对聚苯硫醚结晶行为的影响

本文应用电子计算机对固相热处理的聚苯硫醚(PPS)粉末的X射线衍射图谱进行分峰处理。结果表明,固相热处理使PPS粉末的结晶度下降,同时其平均晶粒体积和垂直于分子链轴方向的晶粒基平面面积增大。与热分析的结果对比,讨论了PPS在固相热处理过程中所发生的物理与化学过程。     

聚苯硫醚及其聚醚砜共混物结晶动力学的研究

本文采用DSC方法,研究了聚苯硫醚及其聚醚砜共混物的等温结晶动力学。结果表明,经α-氯代萘处理后的聚苯硫醚原粉结晶速率常数有明显提高;聚苯硫醚/聚醚砜共混物的Avrami指数较纯聚苯硫醚低,共混物的结晶速率常数随共混组成变化出现最低值;共混物存在明显的二次结晶现象,t_(?)与t_(max)之间存在线性关系。     

聚苯硫醚及其聚醚砜共混物结晶形态的研究

本文借用偏光显微镜(PLM)、扫描电子显微镜(SEM)、小角激光光散射仪(SALS)及蚀刻的方法,研完了聚苯硫醚及其与聚醚砜共混物的结晶形态和织构,讨论了共混方法及其共混组成对其共混物的结晶形态的影响。结果表明,聚苯硫醚在应力作用下能生成横晶;溶液共混物和粉末机械共混物呈现不同的共混结晶形态;随着聚醚砜组分的增加,共混物的织构从聚苯硫醚为连续相逐渐转变为聚醚砜为连续相,同时,聚醚砜的聚集区域从分散在聚苯硫醚的球晶之间转变为聚集在聚苯硫醚的球晶内,使聚苯硫醚的球晶形态逐渐变得不规整。     

聚苯硫醚及其聚砜共混物的结晶形态研究

应用偏光显微镜、扫描电子显微镜及蚀刻的方法,研究了聚苯硫醚及其与聚砜共混物的结晶形态与织构。结果表明,经固相空气热处理的聚苯硫醚,其本体与表面区域的结晶形态有显著的不同;蚀刻择优发生于球晶的晶界上;随着聚砜组份的增加,共混物的织构从聚苯硫醚为连续相逐渐转变为聚砜为连续相,聚苯硫醚的球晶形态也逐渐变得不规整。     

聚对次苯基硫醚(PPS)的分子量及粘度

采用AgCl-Ag_2S型固体膜氯离子敏感电极,测得PPS于氧瓶分解后吸收液中的氯离子摩尔浓度,建立了微量条件下测定PPS分子量的方法。样品未经分级,平行实验的标准偏差在10％左右。从而求得PPS的关系式以及关系式     

热致相分离法制备聚苯硫醚微孔膜

采用热致相分离法,以己内酰胺为溶剂,制备得到了聚苯硫醚微孔膜并对薄膜性能表征.聚苯硫醚-己内酰胺体系制膜的优点之一是溶剂己内酰胺是水溶性的,可以采用纯水作为后处理的萃取剂.选择了合适的浓度,利用压制成型法制备聚苯硫醚平板膜;研究了体系冷却时的相行为,并考察了降温速率、聚合物浓度等因素对微孔形态与薄膜性能的影响.研究表明,聚苯硫醚-己内酰胺体系以固液分相为主,萃取后形成球晶状的微孔结构.降温速率对薄膜的微孔形态、孔径以及连通性有重要影响;当体系以较低降温速率冷却时,多孔形态为枝叶状,形成了更多的开孔结构并获得了更大的孔径,这是获得高通量微孔膜的主要原因.通过控制降温速率可以制备纯水通量大于100 L/m2h,孔径约4～5μm且连通性良好的聚苯硫醚微孔膜;研究了聚合物浓度的影响,薄膜的纯水通量随着聚合物浓度的增大而减小,并且当聚苯硫醚浓度>50 wt%时,由于大于临界浓度而失去渗透性.     

聚苯硫醚的动态力学行为研究

本工作借助TBA技术研究了聚苯硫醚(PPS)的动态力学行为。结果表明,PPS的端基和分子量,热处理方式(固相处理或熔融处理)和处理时间,试样的热历史(淬火或退火)及制辫子所用的纤维的表面性质(玻璃纤维、碳纤维和石墨纤维及其表面处理)等因素对其动态力学行为均有影响。这些动态力学行为特征的变化与这些因素所引起的PPS的分子结构和超分子结构的变化有关。     

聚苯硫醚纤维的抗张强度与工艺和结构的关系

以熔融纺丝法制备出不同结晶度的各向同性聚苯硫醚纤维作为样品,根据密度和声速测定值确定出PPS晶相和无定形相的本征横向声模量E0⊥,c(4.40 GPa)和E0⊥,am(1.99 GPa).利用密度梯度法测定出的结晶度Xc和X-衍射法测定的晶区取向因子fc,按照Samules模型计算出不同牵伸和定型工艺下制备的PPS纤维样品的非晶区取向因子(fam),在此基础上分析PPS纤维抗张强度与牵伸定型工艺参数、结构之间的关系.结果表明,PPS纤维的最佳牵伸温度及紧张热定型温度分别在90℃和190℃附近;提高PPS纤维的牵伸温度及紧张热定型温度可以增加纤维的结晶度,在一定范围内对纤维抗张强度的增加有促进作用;但较高的牵伸温度及紧张热定型温度不利于纤维非晶区取向的提高,造成PPS纤维抗张强度降低.牵伸倍数的增加可以有效提高PPS纤维的非晶区取向程度,抗张强度也随着增加.     

Preparation and characterization of polyphenylene sulfide–based chelating resin–functionalized 2‐amino‐1,3,4‐thiadiazole for selective removal Hg(II) from aqueous solutions

A novel chelating resin (PPS‐ATD) containing N and S elements was prepared through the chloromethylation of polyphenylene sulfide resin and subsequent functionalization with 2‐amino‐1,3,4‐thiadiazole (ATD). The structure of PPS‐ATD was systematically characterized and analyzed by the Fourier transform infrared spectroscopy, elemental analysis, thermogravimetric analysis, scanning electron microscope, and energy dispersive spectrometer. The adsorption performance of PPS‐ATD was evaluated by batch methods at different pH, temperature, adsorption time, and initial concentration, and the results showed that the PPS‐ATD exhibited high adsorption capacity (197.79 mg·g⁻¹ at 298 K) and selectivity for Hg(II). The adsorption of PPS‐ATD for Hg(II) was well fitted by the Langmuir isotherm model, and the adsorption process was endothermic. After 5 consecutive regeneration cycles, no obvious loss in the adsorption capacity of the PPS‐ATD was found, which implied that the PPS‐ATD had great application prospects in the treatment of mercury‐containing wastewater.     

聚苯硫醚及其碳纤维复合材料结晶动力学的研究

用膨胀计法研究了聚苯硫醚及其碳纤维复合材料的结晶动力学行为。发现其碳纤维复合材料对Avrami方程有较明显的偏离。聚苯硫醚具有中等的结晶速率,与PE、PMO等高聚物比较,它的σσ_c值、堆砌系数K_c以及结晶动力学方程中的前置指数G_0值较低。G_0是决定高聚物结晶速率的主要因素,ρ_a/ρ_c(值较小的高聚物有可能出现较高的结晶速率。     

Effects of solvent treatment on crystallization kinetics of poly(p-phenylene sulfide)

Isothermal melt crystallization kinetics were investigated by differential scanning calorimetry (DSC) for virgin and α-chloronaphthalene solvent-treated poly(phenylene sulfide) (PPS) systems. The overall crystallization rates were found to be much faster for the solvent-treated PPS than for the virgin neat PPS. Additionally, the Avrami crystallization plot for the solvent-treated PPS samples appeared as two straight portions with an apparent discontinuity, but as a continuous straight line for the virgin PPS system. After the treatment of solvent dissolution and subsequent drying, the residual trace α-chloronaphthalene, upon being quenched to the crystallization temperatures, initiated some localized solvent-induced nuclei-like crystals in PPS. It was the nuclei that enhanced secondary crystallization in treated PPS during the second stage, and the higher extents of secondary crystallization in the solvent-treated PPS caused the apparent discontinuous break in the Avrami plots. The causes for the difference were explained and the mechanism of the sequential primary/secondary crystallization kinetics for the solvent-treated PPS was satisfactorily described with a proposed series-parallel crystallization model. ©1995 John Wiley & Sons, Inc.     

Non-isothermal crystalliztion kinetics of poly(phenylene sulfide) with low crosslinking levels

Poly(phenylene sulfide) (PPS) with different crosslinking levels was successfully fabricated by means of high- temperature isothermal treatment (IT). The crosslinking degree of PPS was increased with IT time as revealed by Fourier-transform infrared spectroscopy and dynamic viscosity measurements. Its influence on the non-isothermal crystallization behaviors of PPS was studied by differential scanning calorimeter (DSC). The crystallization peak temperature of PPS with 6 h IT was 15 K higher than that of the one with 2 h IT at 30 K/min cooling rate. The non-isothermal crystallization data were also analyzed based on the Ozawa model. The Ozawa exponent m decreased from 3.5 to 2.2 at 232℃ with the increase of the IT time, suggestive of intensive thermal oxidative crosslinking reducing the crystallite dimension as PPS crystal grew. The reduced cooling crystallization function K(T) was indicative of the larger activation energy of crosslinked PPS chain diffusion into crystal lattice, resulting in a slow crystal growth rate. Additionally, the overall crystallization rate of PPS was also accelerated with the increase of crosslinking degree from the observation of polarized optical micrograph. These results indicated that the chemical crosslinked points and network structures formed during the high-temperature isothermal treatment acted as the effective nucleating sites, which greatly promoted the crystallization process of PPS and changed the type of nucleation and the geometry of crystal growth accordingly.     

Monitoring photoproduct formation and photobleaching by fluorescence spectroscopy has the potential to improve PDT dosimetry with a verteporfin-like photosensitizer

In current clinical practice, photodynamic therapy (PDT) is carried out with prescribed drug doses and light doses as well as fixed drug-light intervals and illumination fluence rates. This approach can result in undesirable treatment outcomes of either overtreatment or undertreatment because of biological variations between different lesions and patients. In this study, we explore the possibility of improving PDT dosimetry by monitoring drug photobleaching and photoproduct formation. The study involved 60 mice receiving the same drug dose of a novel verteporfin-like photosensitizer, QLT0074, at 0.3 mg/kg body weight, followed by different light doses of 5, 10, 20, 30, 40 or 50 J/cm2 at 686 nm and a fluence rate of 70 mW/cm2. Photobleaching and photoproduct formation were measured simultaneously, using fluorescence spectroscopy. A ratio technique for data processing was introduced to reliably detect the photoproduct formed by PDT on mouse skin in vivo. The study showed that the QLT0074 photoproduct is stable and can be reliably quantified. Three new parameters, photoproduct score (PPS), photobleaching score (PBS) and percentage photobleaching score (PBS%), were introduced and tested together with the conventional dosimetry parameter, light dose, for performance on predicting PDT-induced outcome, skin necrosis. The statistical analysis of experimental results was performed with an ordinal logistic regression model. We demonstrated that both PPS and PBS improved the prediction of skin necrosis dramatically compared to light dose. PPS was identified as the best single parameter for predicting the PDT outcome.     

Isothermal crystallization kinetics,morphology, and thermal conductivity of graphene nanoplatelets/polyphenylene sulfide composites

Graphene nanoplatelets (GNP) and polyphenylene sulfide (PPS) were used as filler and matrix, respectively, to produce composites. The PPS/GNP thermal composites were prepared via a melt blending method. The effects of GNP on crystallization behavior and kinetics, morphology, and thermal properties of PPS/GNP composites were investigated. To determine the isothermal crystallization kinetics parameters and isothermal crystallization activation energy, the Avrami model was used to comparatively analyze the relevant DSC experimental data. The results show that GNP provides an obvious heterogeneous nucleation effect on PPS to accelerate the crystallization and decrease isothermal crystallization activation energy. Thermal conductivity values of PPS/GNP composites with various GNP contents revealed that GNP remarkably increases thermal conductivity of composites mainly via a layered dispersion in PPS matrix. Thermal conductivity also increased with increasing GNP content, which was further improved at elevated temperatures. The thermal conductivities of PPS composite containing 30 mass% of GNP were 1.156 and 1.350 W m^?1 K^?1 at 30 and 110 °C, respectively, indicating an increase of more than 3 times compared with the neat PPS.     

Thermal and dynamic mechanical properties of PES/PPS blends

Blends of poly(ether-sulfone) (PES) and poly(phenylene sulfide) (PPS) with various compositions were prepared using an internal mixer at 290°C and 50 rpm for 10 min. The thermal and dynamic mechanical properties of PES/PPS blends have been investigated by means of DSC and DMA. The blends showed two glass transition temperatures corresponding to PPS-rich and PES-rich phases. Both of them decreased obviously for the blends with PES matrix. On the other hand, T_g of PPS and PES phase decreased a little when PPS is the continuous phase. In the blends quenched from molten state the cold crystallization temperature of PPS was detected in the blends of PES/PPS with mass ratio 50/50 and 60/40. The melting point, crystallization temperature and the crystallinity of blended PPS were nearly unaffected when the mass ratio of PES was less than 60%, however, when the amount of PES is over 60% in the blends, the crystallization of PPS chains was hindered. The thermal and the dynamic mechanical properties of the PPS/PES blends were mainly controlled by the continued phase. This revised version was published online in August 2006 with corrections to the Cover Date.     

原位聚合MnO_2/PoPD@PPS复合滤料及其NH_3-SCR脱硝性能研究

在聚苯硫醚(PPS)滤料表面包覆一层二氧化锰/聚邻苯二胺(PoPD)复合物。利用π-π共轭效应,将邻苯二胺(OPD)单体均匀吸附在PPS纤维表面,然后通过高锰酸钾溶液使邻苯二胺氧化聚合,在纤维表面原位生成聚邻苯二胺包覆层,同时高锰酸钾被还原成MnO_2催化剂,插入到聚邻苯二胺基体中。通过原位聚合生成的MnO_2/PoPD复合物与PPS滤料间有很强的黏结性,使得催化剂和滤料能牢固地结合在一起。该复合滤料制备方法简单,实验条件温和,对滤料本身性能没有损伤,通过FESEM、XPS、XRD、FT-IR、脱硝活性测试等对其结构和性能进行了研究。脱硝测试结果表明,KMnO4/PPS质量比为1∶1时,复合滤料在80-180℃下脱硝率可达36%-94%,10 h的催化剂稳定性测试中,其脱硝率在160℃下仍保持在88%;Mn 2p的XPS谱图证实复合滤料上催化剂为MnO_2;复合滤料的XRD谱图表明MnO_2为非晶结构;从FESEM照片可以看出,MnO_2催化剂在PPS滤料上分散均匀。     

Phase separation in semicrystalline blends of poly(phenylene sulfide) and poly(ethylene terephthalate). II. Effect of poly(phenylene sulfide) homopolymer solubilization of PPS‐graft‐PET copolymer on morphology and crystallization behavior

The morphology and crystallization behavior of poly(phenylene sulfide) (PPS) and poly(ethylene terephthalate) (PET) blends compatibilized with graft copolymers were investigated. PPS‐blend‐PET compositions were prepared in which the viscosity of the PPS phase was varied to assess the morphological implications. The dispersed‐phase particle size was influenced by the combined effects of the ratio of dispersed‐phase viscosity to continuous‐phase viscosity and reduced interfacial tension due to the addition of PPS‐graft‐PET copolymers to the blends. In the absence of graft copolymer, the finest dispersion of PET in a continuous phase of PPS was achieved when the viscosity ratio between blend components was nearly equal. As expected, PET particle sizes increased as the viscosity ratio diverged from unity. When graft copolymers were added to the blends, fine dispersions of PET were achieved despite large differences in the viscosities of PPS and PET homopolymers. The interfacial activity of the PPS‐graft‐PET copolymer appeared to be related to the molecular weight ratio of the PPS homopolymer to the PPS segment of the graft copolymer (M_H/M_A). With increasing solubilization of the PPS graft copolymer segment by the PPS homopolymer, the particle size of the PET dispersed phase decreased. In crystallization studies, the presence of the PPS phase increased the crystallization temperature of PET. The magnitude of the increase in the PET crystallization temperature coincided with the viscosity ratio and extent of the PPS homopolymer solubilization in the graft copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 599–610, 2000     

聚间苯硫醚和聚对苯硫醚的对比表征

聚对苯硫醚[poly(pphenylenesulfide),简称pPPS]的分子链是由对苯撑基和硫原子交替连接构成而使制品抗冲击能力差[1](有些研究者用共聚或共混的方法在pPPS中引入间位结构来达到减少其结晶度,增强韧性的目的)。余自力等[2]用硫磺溶液法合成了mPPS、pPPS及其共聚物,认为在pP...     

Effect of sizing materials of carbon fiber on solid-state cure of poly(p-phenylene sulfide)

The effect of sized carbon fibers on the solid-state cure of poly(p-phenylene sulfide) (PPS) was studied using differential scanning calorimetry. PPS resin reinforced with sized carbon fiber exhibited the largest cure peak for all cure temperatures and showed a second peak at low cure temperature which was absent in both PPS reinforced with desized carbon fiber and neat PPS resin. In a separate experiment in which epoxy prepolymer/PPS mixture was cured, the exothermic reaction was related to the presence of the epoxy sizing used on the carbon fiber. © 1998 John Wiley & Sons, Ltd.     

聚苯硫醚/尼龙6共混物界面对结晶行为的影响

高分子作为材料时 ,其力学性能受其结晶形态的影响 ,而其结晶形态与其结晶行为有关 .结晶性聚合物共混物中结晶组分由于第二组分存在 ,改变了结晶组分在熔体时的化学与物理环境 .因此 ,其结晶组分的结晶行为不仅取决于两组分在熔体时的相容性 ,而且与第二组分是否起到异相晶核作用和 /或两组分间界面是否诱导成核作用有关 ,从而影响共混物中结晶组分的结晶行为 ,导致共混物力学性能的改变[1～ 4] .在ＰＰＳ/ＰＡ6共混物中 ,由于ＰＰＳ的熔点和熔体结晶温度都比ＰＡ6的高 ,共混物熔体降温结晶ＰＰＳ是在ＰＡ6熔体存在下发生结晶 ,而ＰＡ6是在…