脂溶性酞菁钴(III)为载体的高选择性亚硝酸根PVC膜电极

以自制的4,4',4',4''-四特丁基酞菁钴(II)为原料合成二氯4,4',4',4''-四特丁基酞菁钴(III)。以此为载体制备PVC膜电极。该电极的电位选择性次序明显不同于Hofmeister次序, 其最佳 响应斜率为-52mV/pNO2^-, 线性范围为3×10^-^5～1×10^-^1mol.dm^-^3NaNO2。通过改变配合物轴向的配位阴离子, 用紫外-可见光谱法对电极的响应机理作了初步探讨。     

多孔炭载聚钴酞菁修饰电极用于苯二酚的电催化及检测

以二氧化硅纳米球为模板,通过葡萄糖的水热聚合反应制备了具有三维结构的多孔炭(PC)。采用电化学聚合方法将单体钴酞菁聚合在多孔炭修饰的玻碳电极(PC/GC)表面,制备了多孔炭载聚钴酞菁的修饰电极(Co-TAPc/PC/GC)。通过循环伏安法(CV)研究了间苯二酚、邻苯二酚和对苯二酚在此修饰电极的电化学响应。结果表明,相对于裸玻碳电极、多孔炭或聚钴酞菁单独修饰的电极,该修饰电极对3种同分异构体的酚类物质均有更好的电催化活性。利用计时安培技术,该修饰电极对间苯二酚、邻苯二酚及对苯二酚分别在5.0×10-6～5.0×10-4 mol/L,6.0×10-6～2.5×10-4 mol/L和2.0×10-6～8.0×10-4 mol/L范围内具有较好的线性响应。此修饰电极具有制备简单、响应灵敏、稳定性好等优点。     

电聚合卟啉衍生物修饰的碘离子选择性电极

用电化学方法将α,β,γ,δ-四(4-氨基苯基)卟啉单体聚合在铂丝电极上, 可制备化学修饰型I^-选择性电极.质子化卟啉衍生物的立体交联高聚大环与I^- 的作用具有强的主客体效应,使电极对I^-具有高的选择性,并呈现与经典Hofmeister 系列及一般金属卟啉中性载体膜电极不同的阴离子选择性次序:I^-》SCN^-》ClO~4^->NO~2^->Br^->NO~3^->Cl^->SO~4^2^-.电极对1×10^-^1～2.6×10^-^6mol ·dm^-^3呈线性响应,检测下限8.2×10^-^7mol·dm^-^3,斜率61±0.2mV/pI^-(27℃).测试了电极膜的交流阻抗行为.电极具有内阻小,响应快,抗毒化能力强,制备简单等优点     

四羧基酞菁钴-半胱胺自组装修饰金电极对烟酰胺腺嘌呤二核苷酸的电催化研究

本文将(4,4′,4,″4)四羧基酞菁钴(CoTcPc)共价键合到自组装在Au电极表面的半胱胺单分子层上,获得了自组装单分子膜修饰电极(CoTcPc-Cys CME),研究了它的电化学性质,并对电极表面进行了表征。电极表面覆盖度为3.7×10-10mol/cm2,电子转移速率常数Ks为1.21 s-1。实验表明,在pH 7.0的磷酸盐缓冲溶液(PBS)中,CoTcPc/Au对烟酰胺嘌呤二核苷酸(NADH)的氧化具有良好的电催化作用,使NADH在裸金电极上的氧化电位降低了近300 mV,催化电流与cNADH在5.0×10-6~3.2×10-3mol/L范围有线性关系,检出限为2.8μmol/L。测定了电极催化NADH的米氏催化常数KMapp和催化反应速率常数K。     

邻苯二酚紫修饰电极示差脉冲伏安法测定水中铝

利用吸附的方法在热解石墨电极上制得邻苯二酚紫(PCV)修饰电极。在NH~3.H~2O-NH~4Cl底液(pH8.5)中,该电极具有很好的电化学活性,其示差脉冲氧化峰电位为E~p~a=+80mV。对铝进行检测,只是峰电流降低,而峰电位不变,氧化峰电流的降低值与铝浓度在1×10^-^8-1×10^-^7mol.dm^-^3和1×10^-^7-1×10^-^6mol.dm^-^3范围内成正比,检测限为5×10^-^9mol.dm^-^3,标准偏差为5.0%(4×10^-^8mol.dm^-^3Al,n=8),对实际水样进行测定,结果令人满意。对其检测机理进行了研究后认为:(1)PCV修饰电极表面是PCV单分子层吸附,具有很好的电化学活性;(2)铝与PCV在电极表面形成一1:3的配合物,该配合物在修饰电极上本身没有电化学活性,仅覆盖住原有的PCV电活性点,从而使峰电流降低,而峰电位没有变化;因此,在有铝和无铝时,电极过程没有变化,都对应于PCV的电化学行为。我们用电化学方法、扫描电镜、X射线光电子能谱和X射线荧光光谱法对此进行了证明。     

KTiOPO4单晶膜钾离子选择性电极的研究

本文采用KTiOPO4单晶薄片作为离子活性传感膜, 制备了钾离子选择性电极。20℃时, 其线性响应范围为1.2×10^-^5～1.0mol.dm^-^3氯化钾溶液, 平均响应斜率为58mV/-lgak, 对钠离子的电位选择性系数为4.0×10^-^4。该电极的优点是电极斜率受酸度变化影响小, 稳定性和重现性好, 寿命长。     

酞菁钴及其衍生物修饰电极对分子氧的电催化还原

在玻碳电极上采用吸附法制备了四溴代酞菁钴(CoPcBr₄)、酞菁钴(CoPc)和四-α-(2,2,4-三甲基-3-戊氧基)酞菁钴(CoPc(OC₈H₁₇)₄)修饰电极。利用循环伏安法和线性扫描伏安法研究了修饰电极在酸性介质中对分子氧的电催化还原,比较了不同取代基的酞菁钴对电催化性质的影响。结果表明,它们对分子氧还原均具有良好的电催化活性,其中酞菁钴和四-α-(2,2,4-三甲基-3-戊氧基)酞菁钴对O₂的催化是2电子还原生成H₂O₂,与裸电极相比,O₂的还原峰电位分别向正方向移动了0.33和0.48 V。而四溴代酞菁钴修饰电极在-0.1和-0.7 V附近产生的2个还原峰,说明它催化O₂到H₂O₂的还原以后还可以促进H₂O₂继续还原到H₂O,最终实现O₂的4电子还原。     

酞菁钴修饰碳糊电极对微量苯酚的测定

研究了苯酚在酞菁钴修饰碳糊电极上的电化学行为,提出了催化反应的机理,并以此为依据,用伏安法以酞菁钴修饰碳糊电极为工作电极测定了微量苯酚.在pH 8.7的磷酸盐缓冲溶液(PBS)中,苯酚在0.61 V(对SCE)出现一氧化峰,该峰电流与苯酚的浓度在5.0×10-7～1.0×10-4 mol/L之间呈线性关系,检出限为1.0×10-7 mol/L.此法可用于工业废水中苯酚的测定.     

长链四烷基锡作中性载体的亚硝酸根选择性电极的研究

用亲脂的长链四烷基锡作中性载体制备亚硝酸根选择性电极. 其选择性模式与经典的阴离子交换剂相比有显著不同, 相对硝酸根的电位选择性系数改善约4个数量级. 线性响应区间为1x10^-^1-2x10^-^5mol.dm^-^3, 检测下限为5x10^-^6mol.dm^-^3. 电极斜率在弱性介质中为Nernst响应, 在弱酸性介质中为两倍Nernst响应. 紫外光谱研究发现酸度影响载体与阴离子的多级配位平衡. 电极斜率的变化与此平衡密切相关, 在此基础上给出了对电极斜率的异常变化及电位-pH     

二维聚硫杂酞菁铜的合成与性质

以四氰基-1,4-二噻英为原料,分别用无溶剂法和溶剂法合成了平面稠合型网状聚硫杂酞菁铜PCuS~8Pc(A)和(B),经元素分析,热谱,IR, 电子吸收与发射光谱表征.PCuS~8Pc具有光敏性和本征半导体性能,σ~2~9~8~K(A):2.29×10^-^6Ω^-^1 ·cm^-^1,(B):5.83×10^-^6Ω^-^1·cm^-^1     

二(乙基黄原酸基)金属配合物为中性载体高选择性碘离子电极的研究

本文研究了二(乙基黄原酸基)金属配合物为中性载体的阴离子选择性电极,其中二(乙基黄原酸基)钴(Ⅱ)对碘离子有高的选择性, 且电极呈现反Hofmeister行为, 其选择次序是: I^->SCN^->NO2^->Br^->ClO4^->SO4^2^->NO3^->Cl^-, 采用交流阻抗和光谱分析技术研究了电极的响应机理, 并将电极用于药品分析,结果令人满意。     

[Ru(bpy)2(L-Trp)]ClO4-KCl水溶液体系的电致化学发光特性研究

合成了[Ru(bpy)2(L-Trp)]ClO4, 并对其电致化学发光特性进行研究。发现在KCl溶液中, 在三角波脉冲电压作用下, 该配合物在铂电极上有电致化学发光活性。其线性动力学响应范围为5.9×10^-^9～1.2×10^-^7mol . L^-^1。当信噪比为3时, 可检测浓度为5.9×10^-^9mol . L^-^1。浓度为5.9×10^-^8mol . L^-^1时, 10次测试的相对标准偏差为5.3%。根据电化学研究的结果, 提出了该配合物的电致化学发光反应机理。     

混合溶剂中性载体镁离子选择性微电极的研究

用氯化石腊和邻硝基苯辛醚为混合溶剂制备中性载体ETH5214的镁离子选择性微电极,相对于钾离子的电位选择性系数较单独以邻硝基苯辛醚为溶剂的ETH5214镁微电极改善0.9个数量级。在纯MgCl~2和在含细胞内典型离子背景的MgCl~2溶液中,响应斜率为Nernst响应,检测下限分别为4×10^-^7mol.dm^-^3和2×10^-^5mol.dm^-^3。在pH3.5-9.5范围内,氢离子对电极的电位响应无影响。测量的重现性良好。电极的实用响应时间(t~9~5)≤3s,有效寿命长于5天。     

聚苯胺黄嘌呤氧化酶电极的生物电化学活性

用电化学方法将黄嘌呤氧化酶固定在聚苯胺中以制成聚苯胺黄嘌呤氧化酶电极。该电极呈现典型的酶催化反应动力学特性。且具有快速的生物电化学响应。固定化黄嘌呤氧化酶的表观米氏常数为21×10^-^6mol.dm^-^3, 最适pH为8.4,酶催化反应的活化能为85.1kJ.mol^-^1。酶电极具有较高的稳定性。使用聚苯胺黄嘌呤氧化酶电极能可靠地测定较低的底物浓度, 如2×10^-^6mol.dm^-^3黄嘌呤。     

A novel PVC membrane sensor for determination of loratadine in pharmaceutical compounds and blood serum

A novel PVC membrane-selective electrode based on loratadine-tetraphenyl borate ion-pair was prepared for the determination of loratadine potentiometrically. This electrode exhibits a Nernstian slope of 59.1 ± 0.3 mV decade^-1 for loratadine in a concentration range of 5.0 × 10^-6?1.0 × 10^-2 M at pH 2.2 with a detection limit of 2.9 × 10^-6 M. The potential of the electrode is very stable and exhibits good reproducibility with very fast response time (??3 s). The selectivity of the proposed electrode towards some cations and organic compounds was tested and the selectivity coefficients were calculated. The electrode was successfully applied to the determination of loratadine in tablets and blood samples.     

Long-chain tetraalkyltin compounds as neutral carriers for nitrite-selective PVC membrane electrodes

The nitrite-selective PVC membrane electrodes prepared with lipophilic long-chain tetraalkyltin compounds as neutral carrier show selectivity patterns significantly different from those obtained with classical anion-exchangers. The potentiometric selectivity coefficient for nitrite ion with respect to nitrate ion has been improved by about four orders of magnitude. The linear response range of the electrode based on tetralauryltin (TLT) is from 1 × 10^?1M down to 2×10^?5M with a detection limit of 5 × 10^?6M. The Nernstian response of the electrode in the medium of pH≥7 gradually changes to a doubled super-Nernstian response when the solution turns slightly acidic. The change of the response slope has a closely relation with the stepwise complex-formation equilibrium of the carrier with the anion involved, which was experimentally studied by using ultraviolet spectroscopy. An explanation of the anomalous response behavior as well as the curve form of the potential-pH plot is given.     

Sulfite-sensitive solvent/polymeric-membrane electrode based on bis(diethyldithiocarbamato)mercury(II)

A new solvent/polymeric-membrane electrode which exhibits significant potentiometric response toward sulfite ion in the 1 × 10_?6?1 × 10^?3 M range is described. The membrane is prepared by incorporation of neutral bis(diethyldithiocarbamato)mercury (II) in a thin film of plasticized poly (vinyl chloride). In sharp contrast to classical Hofmeister behavior, the resulting membrane displays little or no response to a wide range of anions (log K^pot_i,j ? ?4, i being sulfite) including sulfate, nitrate, nitrite, chloride, perchlorate, salicylate, and alkylsulfonates. Bromide and thiocyanate are moderate interferents, while significant response to iodide, thiosulfate, and sulfide is observed. These selectivity data, along with other response characteristics of the membrane, are used to postulate the mechanism by which the electrode responds to sulfite. Preliminary studies demonstrate that the electrode can be used in conjunction with an outer gas-permeable membrane for highly selective detection of total sulfite species in the form of sulfur dioxide.     

Potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate film-modified electrode

A potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate(III) (CHCF) film-modified glassy carbon electrode is proposed. The electroactive film is introduced onto the glassy carbon electrode surface by electrodeposition of cobalt, which forms a thin CHCF film on subsequent anodic scanning in KClHCl solution (pH 5.0–5.5) containing K₃Fe(CN)₆. The thickness of the film on the electrode surface can be controlled by changing the electrodeposition time and the concentrations of cobalt(II) and Fe(CN)^3?₆ ions. The modified electrode exhibits a linear response in the concentration range 1 × 10^?1 ?3 × 10^?5 M potassium ion activity, with a near-Nernstian slope (48–54 mV per decade) at 25 ± 1°C. The detection limit is 1 × 10^?5 M. The stability, response time and selectivity were investigated. The electrode exhibits good selectivity for potassium ion with the twelve cations investigated. The relative standard deviation is 1.5% (n=10). The effects of the thickness of the electroactive film and the pH of the solution on the electrode response were also investigated.     

Triiodide PVC Membrane Electrode Based on a Charge‐Transfer Complex of Iodine with Ditertbutyl‐Dicyclohexyl‐18‐Crown‐6

A new triiodide ion‐selective electrode based on a charge‐transfer complex of iodine with ditertbutyl‐dicyclohexyl‐18‐crown‐6 (t‐Bu)₂DC18C6 as membrane carrier was prepared. The electrode has a linear dynamic range from 6.3 × 10^?3‐5 × 10^?6 with a Nernstian response of 58.6 ± 1 mV decade^?1 and a detection limit of 1.3 × 10^?6 M. The response time of the sensor was 25 s. The membrane could be used for two months without any divergence in potentials. The electrode exhibits an anti‐Hofmeistetr selectivity sequence with a preference for triiodide at pH 2.0‐10.0. The response mechanism of the electrode was investigated by Uv‐Vis spectroscopic technique. The electrode can be used for the determination of ascorbic acid in orange juice.