ZSM-5、ZSM-57分子筛和丝光沸石间的转晶规律

考察了硅铝比、碱度、有机胺模板剂、晶化时间及温度等合成条件对ZSM-5、ZSM-57 分子筛和丝光沸石之间相互转晶的影响. 发现较高的碱度、较长的晶化时间有利于合成丝光沸石；较低的碱度、较高的诱导晶化温度、较长的晶化时间有利于合成低硅铝比的ZSM-57 分子筛；合成低硅铝比的ZSM-5分子筛则需要在能合成丝光沸石和ZSM-57 分子筛的碱度区间内精确调节碱度, 缩短晶化时间、降低诱导晶化温度、加入适当晶种, 有利于合成低硅铝比的ZSM-5 分子筛. 合成条件稍微改变, 会导致各种沸石之间发生转晶, 晶化产物出现两种或两种以上的晶型.     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N_2吸附-脱附和NH_3-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比(n/n)为30~70,钠硅比(n/n)为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N₂吸附-脱附和NH₃-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比（n/n）为30~70,钠硅比（n/n）为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

系列硅铝比纳米薄层ZSM-5分子筛的合成和表征

以自制不对称双子季铵盐表面活性剂为模板, 在水热合成体系中控制合成系列硅铝比纳米薄层ZSM-5分子筛.采用X射线衍射(XRD)、N₂吸附-脱附、X射线荧光光谱(XRF)、扫描电镜(SEM)和²⁷Al魔角旋转核磁共振(²⁷Al MAS-NMR)对合成的样品进行了表征. 详细研究了晶化温度、晶化时间、结构导向剂(SDA)用量、碱度等对合成的影响和纳米薄层ZSM-5分子筛的形成过程. 结果表明: 分子筛硅铝比越高, 结构导向剂用量越大, 所需的晶化时间越短; 晶化温度越高, 晶化时间越短; 且不同硅铝比纳米薄层ZSM-5分子筛的形貌规整度、比表面积和介孔/微孔孔容比例随着硅铝比而变化.     

MFI/MFI核壳分子筛的合成及催化性能研究

通过对核相ZSM-5的预处理步骤和在温和水热条件下的二次生长, 合成了壳层硅铝比高、核相硅铝比低、纳米晶壳层致密的MFI(核)/MFI(壳)型核壳分子筛材料. 考察了晶化温度和晶化时间对高硅壳层MFI/MFI核壳型沸石分子筛的合成的影响, 其适宜的合成条件为晶化温度高于130 ℃, 晶化时间19 h. 核相ZSM-5的预处理步骤对于成功合成此特殊核壳型分子筛材料十分关键. 与普通ZSM-5沸石分子筛相比, MFI/MFI核壳分子筛在催化甲苯甲基化反应时的失活效率显著降低.     

ZSM-5分子筛结晶度及晶粒大小的影响因素

以硅溶胶为硅源,偏铝酸钠为铝源,用晶种法制备ZSM-5分子筛.考察了物料混合方式、陈化时间、晶化时间、晶化温度、碱度和水量等对ZSM-5分子筛相对结晶度和晶粒大小的影响.用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和激光粒度分析等对所合成样品进行了表征.结果表明:在一定的高碱度条件下形成高浓度的硅铝酸盐凝胶,才能合成出晶化良好的样品,ZSM-5分子筛是按固相机理形成的;合成ZSM-5分子筛的相对结晶度和平均颗粒度均随晶化温度的升高及硅铝酸盐凝胶浓度的增加而增大,在室温陈化24 h、180℃晶化12～24 h时相对结晶度最高,平均颗粒度基本上与陈化时间无关.     

在含乙醇的硅铝凝胶中合成ZSM-5沸石

用含乙醇的硅铝凝胶水热晶化合成ZSM-5沸石.实验表明,乙醇能够促进ZSM-5沸石晶体的成核和生长,具有明显的模板剂作用.向含乙醇的凝胶中加入晶种可以进一步缩短晶化诱导期和晶化时间,并减小分子筛的晶粒度.晶种的粒度与分子筛产物的晶粒度有一定对应关系.采用搅拌晶化也能明显地减小ZSM-5沸石的晶粒度,同时影响晶体形貌.通过优化晶化条件和凝胶组成,成功合成出硅铝比在30～240范围内、结晶度较高的ZSM-5沸石分子筛,所得沸石孔道畅通,热稳定性、水热稳定性高,且具有较强酸性,具有良好的应用前景.     

高硅分子筛ZSM-23催化裂解C4烷烃制乙烯丙烯的研究

采用廉价的硅溶胶作为硅源,吡咯烷为模板剂,静态水热晶化法合成出不同硅铝比的ZSM-23分子筛.采用XRD,SEM,吡啶吸附红外光谱等技术,对合成的ZSM-23分子筛的结构、形貌、表面酸性质进行了表征.并进行了所制样品对C4烷烃催化裂解制乙烯丙烯反应催化性能的研究.本文详细考察了硅铝比、反应温度、反应空速以及催化剂稳定性等各种因素对催化性能的影响.结果表明,ZSM-23分子筛的乙烯丙烯收率达到56.0%,丁烷转化率达到88.9%.     

低硅铝比ZSM-5分子筛的合成及其正庚烷裂化反应性能

以氨水为矿化剂,通过添加NH₄⁺离子水热合成了具有较低骨架硅铝比的ZSM-5分子筛。通过X射线衍射(XRD)、扫描电镜(SEM)、固体核磁共振(MAS-NMR)等表征手段,研究了硅源、铝源、矿化剂、阳离子等对ZSM-5分子筛的结晶度、形貌尺寸和骨架硅铝比等的影响,研究了ZSM-5分子筛的骨架硅铝比对正庚烷催化裂化反应的影响。研究表明,投料硅铝比越低,铝原子越难进入到分子筛骨架中;当氨水为矿化剂、正硅酸四乙酯为硅源时可以合成骨架硅铝比较低的氢型ZSM-5分子筛,添加NH₄⁺离子可以增强骨架铝的嵌入,进一步降低分子筛的骨架硅铝比(24.2)。正庚烷裂化反应结果表明,降低分子筛的骨架硅铝比可以提高正庚烷裂化反应的活性,但会降低低碳烯烃的选择性。     

多级孔HZSM-5分子筛的制备及其催化合成聚甲氧基二甲醚的性能

采用两步结晶法,用不同硅源铝源在无介孔模板剂的情况下,直接合成具有多级孔结构的ZSM-5分子筛;利用XRD、SEM、N₂吸附/脱附、Py-IR等技术对合成的多级孔ZSM-5分子筛结构、形貌、织构和酸性质进行表征,并考察其催化甲缩醛和三聚甲醛合成聚甲氧基二甲醚(PODE)的催化性能。结果表明：硅源铝源会影响分子筛结晶过程的晶体尺寸,粒径小的纳米粒更容易相互堆叠形成晶间孔隙;以正硅酸乙酯为硅源,分别以硝酸铝、偏铝酸钠和硫酸铝为铝源合成的3个多级孔ZSM-5分子筛具有较大的介孔体积和较高的B酸/L酸值,在催化合成PODE反应中表现出较好的催化性能;三者对三聚甲醛的转化率均达90%以上,对PODE_3~8选择性分别为62.22%、62.35%和62.12%。      

硅源对MCM-22分子筛合成及物化性质的影响

在动态水热条件下,研究了硅溶胶、白炭黑、硅酸及硅胶为硅源时对MCM-22分子筛合成及物化性质的影响。以硅溶胶、白炭黑、硅酸三种硅源均可合成出高结晶度且无杂晶的片状MCM-22分子筛,其平均粒径分别为190、220和750 nm。硅源影响分子筛的聚集形态,三种硅源分别形成晶粒分散、晶粒半分散及晶粒聚集形态。三组样品的酸强度分布基本一致,都具有较多的中强酸分布,由硅溶胶和硅酸所得MCM-22分子筛在中强酸范围具有更高的B/L酸比值,以白炭黑合成的分子筛总酸量最高。NMR结果表明,样品中的铝以骨架铝为主,不存在明显的非骨架铝。由于硅胶对合成体系中游离水的吸附作用,水热反应难以发生,不能得到MCM-22分子筛,硅胶作为分子筛合成硅源时需要选择合适的反应条件。     

气相转移法与水热合成法合成ZSM-5/SAPO-5核壳结构复合分子筛的比较

以磷酸、拟薄水铝石和硅溶胶为原料,三乙胺为模板剂,在不同晶化温度和晶化时间的实验条件下,分别采用水热合成法和气相转移法合成了一系列ZSM-5/SAPO-5核壳结构复合分子筛,并用X射线衍射、扫描电镜、X射线能量散射谱、红外光谱和N2吸附等手段对其进行了表征.结果表明,所合成的分子筛是以ZSM-5为核,以SAPO-5为壳的双结构复合分子筛.晶化温度的提高和晶化时间的延长有利于分子筛结晶度的提高.与水热合成法相比,采用气相转移法可以减小壳层SAPO-5的颗粒尺寸,减少脱离ZSM-5表面独立生长的SAPO-5的量,改善SAPO-5在ZSM-5表面的分布.重油裂化结果表明,核壳结构复合分子筛对生成低碳烯烃的催化性能优于机械混合的样品.     

双矿化剂对合成ZSM-5分子筛酸性和织构特征及其甲醇转化制丙烯催化性能的影响

采用静态水热法在F^--OH^-体系中,以四丙基氢氧化铵为模板剂、偏铝酸钠为铝源、正硅酸乙酯为硅源,合成了纳米SiO₂-ZSM-5分子筛,考察了F^-/Al₂O₃物质的量比对所合成的ZSM-5分子筛织构性质和甲醇转化制丙烯催化性能的影响。结果发现,随着初始溶胶F^-/Al₂O₃物质的量比的增大,产物中SiO₂的含量增大,ZSM-5分子筛的相对结晶度有所降低;同时,分子筛的比表面积和孔容减小、酸强度降低、酸量减少。对于甲醇转化制丙烯,最佳F^-/Al₂O₃物质的量比为12;此时,丙烯选择性高于45%,丙烯/乙烯（P/E）比值大于10。反应机理分析表明,过渡态择形选择性是控制烯烃选择性的重要因素。     

Synthesis and catalytic performance of ZSM-5/MCM-41 composite molecular sieve from palygorskite

ZSM-5/MCM-41 composite molecular sieve has been hydrothermally synthesized through a two-step crystallization process using palygorskite (PAL) as silicon and aluminum source. The products were characterized by various means and their catalytic properties for acetalization of cyclohexanone and esterification of acetic acid and n-butanol were also investigated. In the first step ZSM-5 zeolite could be formed from the acid-treated PAL after hydrothermal treatment using tetrapropylammonium bromide as template. XRD patterns, N₂ adsorption and desorption data, and TEM images show that the composite obtained in the secondary step had a well-ordered mesoporous MCM-41 phase and a microporous ZSM-5 zeolite phase. Compared with ZSM-5, ZSM-5/MCM-41 composite possessed more total acid amount, weak acid sites and large pore structure due to the formation of MCM-41 and exhibited higher catalytic activity for the acetalization and esterification reaction.     

高岭土微球上无胺法ZSM-5的原位合成

无胺体系中,采用水热法在焙烧高岭土微球上原位晶化合成了ZSM-5分子筛。考察了晶化温度、晶化时间、晶种加入量以及合成体系硅铝比等主要因素对分子筛合成的影响,得出了较佳的原位晶化合成条件。采用XRD、SEM、N₂吸附脱附等手段对合成样品进行了表征。结果表明：在高岭土微球上合成出了颗粒尺寸小于1 μm的小晶粒原位ZSM-5分子筛;晶化产物的比表面积、总孔容、微孔表面积和微孔孔容均明显增大,微孔分布集中于0.54 nm。     

The Effects of Various Sources and Templates on the Microwave‐assisted Synthesis of BZSM‐5 Zeolite

Isomorphic substitution of boron into ZSM‐5 zeolite under microwave‐assisted hydrothermal conditions was systematically studied. When microwave treatment and conventional heating were used, BZSM‐5 zeolite could be obtained within one day, whereas the synthesis of BZSM‐5 under conventional hydrothermal conditions took five days at 180 °C. Various parameters that affect the crystallization of BZSM‐5, such as templates, crystallization time, the silicon source and the Si/B ratio were investigated. Systematic variations of these parameters revealed that this zeolite can be obtained from the reaction mixture with optimized ratios of Si/B > 0.6. Among various tested sources, tetraethylorthosilicate (TEOS) turned out to be the best source for synthesis of borosilicate zeolite and further investigations were done with TEOS as silicon source. The obtained products were characterized by XRD, SEM, and IR spectroscopic techniques.     

Synthesis of mono- and bi-layer zeolite films on alumina substrates

Bilayer zeolite films ZSM-5/ZSM-5, ZSM-5/EMC-1 and NaY/ZSM-5 were synthesized on α-alumina plates. The bottom ZSM-5 or faujasite Y (NaY) zeolite layers were obtained by direct hydrothermal synthesis or by using a seeding step followed by a secondary growth method, respectively, while the secondary growth method was used for the synthesis of all the top zeolite layers. A complete characterization of the obtained materials is proposed using various techniques, such as X-ray diffraction, scanning electron microscopy, X-ray fluorescence and nitrogen sorption measurements. Continuous and highly crystallized bi-layer zeolite films with thicknesses around 11–18 μm were obtained.     

Synthesis and Characterization of ZSM-5/β Co-Crystalline Zeolite

ZSM-5/β co-crystalline zeolites with different content of ZSM-5 have been synthesized by adding different amount of ZSM-5 to the synthetic system of β zeolite with NaAlO2, silica sol as the source of aluminum and silica, respectively, and TEA as the template under controlled condition of the synthesis. The ZSM-5/β co-crystalline zeolite was studied by XRD, SEM, BET and NH3-TPD. The reaction activity of toluene alkylation was investigated with a mixture of toluene-methanol as the feedstock in a pulse micro-reactor over the ZSM-5/β co-crystalline zeolite. It is found that ZSM-5/β co-crystalline zeolite has two kinds of zeolite structure including ZSM-5 and β zeolite, not in the form of a physical mixture. The pore structure of ZSM-5/β co-crystalline zeolites is different from that for β zeolite, ZSM-5 and their physical mixture. In addition, the peaks of both high and low temperature desorption of ammonia over the ZSM-5/β co-crystalline zeolite shift 23 ℃ to lower temperatures and the acid amount of its strong acid is 3% more than the physical mixture. So the ZSM-5/β co-crystalline zeolite produces the highest content of xylene, which is 10.4% higher than the physical mixture. And the ZSM-5/β co-crystalline zeolite has better selectivity for toluene alkylation and weaker de-methylation than β zeolite, ZSM-5 and their physical mixture.     

Secondary Synthesis and Characterization of Boron-Containing ZSM-5 Zeolites

Under conditions of secondary synthesis and to varying extents, boron can be incorporated into the tetrahedral framework sites of a ZSM-5 zeolite which has been synthesized template-free or in the presence of organic template compounds and subjected to calcination or hydrothermal treatment. Isomorphic incorporation of boron is verified by means of ¹¹B MAS NMR measurements and it is reflected in a contraction of the unit cell volume of the zeolite lattice. A comparative study of the catalytic properties of the boron-containing ZSM-5 in acid catalysed n-hexane cracking revealed that samples based on template synthesis product are more active and show less tendency to deactivation.