The Use of Porous Fins for Heat Transfer Augmentation in Parallel-Plate Channels

In this study, a steady, fully developed laminar forced convection heat augmentation via porous fins in isothermal parallel-plate duct is numerically investigated. High-thermal conductivity porous fins are attached to the inner walls of two parallel-plate channels to enhance the heat transfer characteristics of the flow under consideration. The Darcy–Brinkman–Forchheimer model is used to model the flow inside the porous fins. This study reports the effect of several operating parameters on the flow hydrodynamics and thermal characteristics. This study demonstrates, mainly, the effects of porous fin thickness, Darcy number, thermal conductivity ratio, Reynolds number, and microscopic inertial coefficient on the thermal performance of the present flow. It is found that the highest Nusselt number is achieved at fully filled porous duct which requires the highest pumping pressure. The results show that using porous fins requires less pumping pressure with comparable high heat augmentation weight against fully filled porous duct. It is found that higher Nusselt numbers are achieved by increasing the microscopic inertial coefficient (A), the Reynolds number (Re), and the thermal conductivity of the porous substrate k ₂. The results show that heat transfer can be enhanced (1) with the use of high thermal conductivity fins, (2) by decreasing the Darcy number, and (3) by increasing microscopic inertial coefficient.     

Effect of Conduction in Bottom Wall on Darcy–Bénard Convection in a Porous Enclosure

Conjugate natural convection-conduction heat transfer in a square porous enclosure with a finite-wall thickness is studied numerically in this article. The bottom wall is heated and the upper wall is cooled while the verticals walls are kept adiabatic. The Darcy model is used in the mathematical formulation for the porous layer and the COMSOL Multiphysics software is applied to solve the dimensionless governing equations. The governing parameters considered are the Rayleigh number (100 ≤ Ra ≤ 1000), the wall to porous thermal conductivity ratio (0.44 ≤ K _r ≤ 9.90) and the ratio of wall thickness to its height (0.02 ≤ D ≤ 0.4). The results are presented to show the effect of these parameters on the heat transfer and fluid flow characteristics. It is found that the number of contrarotative cells and the strength circulation of each cell can be controlled by the thickness of the bottom wall, the thermal conductivity ratio and the Rayleigh number. It is also observed that increasing either the Rayleigh number or the thermal conductivity ratio or both, and decreasing the thickness of the bounded wall can increase the average Nusselt number for the porous enclosure.     

Forced convection of gaseous slip-flow in porous micro-channels under Local Thermal Non-Equilibrium conditions

Steady laminar forced convection gaseous slip-flow through parallel-plates micro-channel filled with porous medium under Local Thermal Non-Equilibrium (LTNE) condition is studied numerically. We consider incompressible Newtonian gas flow, which is hydrodynamically fully developed while thermally is developing. The Darcy–Brinkman–Forchheimer model embedded in the Navier–Stokes equations is used to model the flow within the porous domain. The present study reports the effect of several operating parameters on velocity slip and temperature jump at the wall. Mainly, the current study demonstrates the effects of: Knudsen number (Kn), Darcy number (Da), Forchheimer number (Γ), Peclet number (Pe), Biot number (Bi), and effective thermal conductivity ratio (K _R) on velocity slip and temperature jump at the wall. Results are given in terms of skin friction (C _f Re ^*) and Nusselt number (Nu). It is found that the skin friction: (1) increases as Darcy number increases; (2) decreases as Forchheimer number or Knudsen number increases. Heat transfer is found to (1) decreases as the Knudsen number, Forchheimer number, or K _R increases; (2) increases as the Peclet number, Darcy number, or Biot number increases.     

Temperature dependent viscosity and thermal conductivity effects on combined heat and mass transfer in MHD three-dimensional flow over a stretching surface with Ohmic heating

An analysis has been carried out to obtain the flow, heat and mass transfer characteristics of a viscous electrically conducting fluid having temperature dependent viscosity and thermal conductivity past a continuously stretching surface, taking into account the effect of Ohmic heating. The flow is subjected to a uniform transverse magnetic field normal to the plate. The resulting governing three-dimensional equations are transformed using suitable three-dimensional transformations and then solved numerically by using fifth order Runge–Kutta–Fehlberg scheme with a modified version of the Newton–Raphson shooting method. Favorable comparisons with previously published work are obtained. The effects of the various parameters such as magnetic parameter M, the viscosity/temperature parameter θ _r , the thermal conductivity parameter S and the Eckert number Ec on the velocity, temperature, and concentration profiles, as well as the local skin-friction coefficient, local Nusselt number, and the local Sherwood number are presented graphically and in tabulated form.     

Theoretical analysis of convective heat transfer enhancement of microencapsulated phase change material slurries

This paper analyzes the convective heat transfer enhancement mechanism of microencapsulated phase change material slurries based on the analogy between convective heat transfer and thermal conduction with thermal sources. The influence of each factor affecting the heat transfer enhancement for laminar flow in a circular tube with constant wall temperature is analyzed using an effective specific heat capacity model. The model is validated with results available in the literature. The analysis and the results clarify the heat transfer enhancement mechanism and the main factors influencing the heat transfer. In addition, the conventional Nusselt number definition of phase change slurries for internal flow is modified to describe the degree of heat transfer enhancement of microencapsulated phase change material slurries. The modification is also consistent evaluation of the convective heat transfer of internal and external flows.c volumetric concentration of microcapsules - c_m mass concentration of microcapsules - c_p specific heat, kJ kg^–1 K^–1 - h_fs phase change material heat of fusion, kJ kg^–1 - h_m* modified convective heat transfer coefficient, W m^–2 K^–1 - k thermal conductivity, W m^–1 K^–1 - k_e effective thermal conductivity of slurry, W m^–1 K^–1 - k_b slurry bulk thermal conductivity, W m^–1 K^–1 - ML dimensionless initial subcooling - Mr dimensionless phase change temperature range - Nu conventional Nusselt number - Nu* improved Nusselt number - q_wⁿ wall heat flux, Wm^–2 - Pe Peclet number - Pr Prandtl number - Re Reynolds number - r radial coordinate, m - r₀ duct radius, m - r₁ dimensionless radial coordinate - Ste Stefan number - T temperature, K - T₁ lower phase change temperature limit, K - T₂ upper phase change temperature limit, K - T_i slurry inlet temperature, K - u axial velocity, m/s - v radial velocity, m/s - x axial coordinate, m - x₁ dimensionless axial coordinate - thermal diffusivity, m²/s - dimensionless temperature - dynamic viscosity, N·s/m² - kinematic viscosity, m²/s - _t width of thermal boundary, m - degree of heat transfer enhancement, = h_m*/(h_m*)_single - b bulk fluid (slurry) - b0 slurry without phase change - l liquid - m mean - s solid - f suspending fluid - p microcapsule particles - w wall - single single-phase fluid     

Fully Developed Forced Convection in a Parallel Plate Channel with a Centered Porous Layer

In this study, fully developed heat and fluid flow in a parallel plate channel partially filled with porous layer is analyzed both analytically and numerically. The porous layer is located at the center of the channel and uniform heat flux is applied at the walls. The heat and fluid flow equations for clear fluid and porous regions are separately solved. Continues shear stress and heat flux conditions at the interface are used to determine the interface velocity and temperature. The velocity and temperature profiles in the channel for different values of Darcy number, thermal conductivity ratio, and porous layer thickness are plotted and discussed. The values of Nusselt number and friction factor of a fully clear fluid channel (Nu _cl = 4.12 and fRe _cl = 24) are used to define heat transfer increment ratio (e_th = Nu_p/Nu_cl)({\varepsilon _{\rm th} =Nu_{\rm p}/Nu_{\rm cl})} and pressure drop increment ratio (e_p = fRe_p/fRe_cl )({\varepsilon_{\rm p} =fRe_{\rm p}/fRe_{\rm cl} )} and observe the effects of an inserted porous layer on the increase of heat transfer and pressure drop. The heat transfer and pressure drop increment ratios are used to define an overall performance (e = e_th/e_p)({\varepsilon = \varepsilon_{\rm th}/\varepsilon_{\rm p})} to evaluate overall benefits of an inserted porous layer in a parallel plate channel. The obtained results showed that for a partially porous filled channel, the value of e{\varepsilon} is highly influenced from Darcy number, but it is not affected from thermal conductivity ratio (k _r) when k _r > 2. For a fully porous material filled channel, the value of e{\varepsilon} is considerably affected from thermal conductivity ratio as the porous medium is in contact with the channel walls.     

Conjugate heat transfer study of incompressible turbulent offset jet flows

In the present case, the conjugate heat transfer involving a turbulent plane offset jet is considered. The bottom wall of the solid block is maintained at an isothermal temperature higher than the jet inlet temperature. The parameters considered are the offset ratio (OR), the conductivity ratio (K), the solid slab thickness (S) and the Prandtl number (Pr). The Reynolds number considered is 15,000 because the flow becomes fully turbulent and then it becomes independent of the Reynolds number. The ranges of parameters considered are: OR = 3, 7 and 11, K = 1–1,000, S = 1–10 and Pr = 0.01–100. High Reynolds number two-equation model (k–ε) has been used for turbulence modeling. Results for the solid–fluid interface temperature, local Nusselt number, local heat flux, average Nusselt number and average heat transfer have been presented and discussed.     

The effect of thermal dispersion on free convection film condensation on a vertical plate with a thin porous layer

An analytical solution to the problem of condensation by natural convection over a thin porous substrate attached to a cooled impermeable surface has been conducted to determine the velocity and temperature profiles within the porous layer, the dimensionless thickness film and the local Nusselt number. In the porous region, the Darcy–Brinkman–Forchheimer (DBF) model describes the flow and the thermal dispersion is taken into account in the energy equation. The classical boundary layer equations without inertia and enthalpyterms are used in the condensate region. It is found that due to the thermal dispersion effect, the increasing of heat transfer is significant. The comparison of the DBF model and the Darcy–Brinkman (DB) one is carried out.     

Thermal convection in a porous layer: Effects of anisotropy and surface boundary conditions

The theory describing the onset of convection in a homogeneous porous layer bounded above and below by isothermal surfaces is extended to consider an upper boundary which is partly permeable. The general boundary condition p + λ ∂p/∂n = constant is applied at the top surface and the flow is investigated for various λ in the range 0 ⩽ λ < ∞. Estimates of the magnitude and horizontal distribution of the vertical mass and heat fluxes at the surface, the horizontally-averaged heat flux (Nusselt number) and the fraction of the fluid which recirculates within the layer are found for slightly supercritical conditions. Comparisons are made with the two limiting cases λ → ∞, where the surface is completely impermeable, and λ = 0, where the surface is at constant pressure. Also studied are the effects of anisotropy in permeability, ξ = K _H /K _V , and anisotropy is thermal conductivity, η = k _H /k _V , both parameters being ratios of horizontal to vertical quantities. Quantitative results are given for a wide variety of the parameters λ, ξ and η. In the limit ξ/η → 0 there is no recirculation, all fluid being converted out of the top surface, while in the limit ξ/η → ∞ there is full recirculation.     

Natural Convection in a Cavity Filled with Porous Layers on the Top and Bottom Walls

Natural convection in a partially filled porous square cavity is numerically investigated using SIMPLEC method. The Brinkman-Forchheimer extended model was used to govern the flow in the porous medium region. At the porous-fluid interface, the flow boundary condition imposed is a shear stress jump, which includes both the viscous and inertial effects, together with a continuity of normal stress. The thermal boundary condition is continuity of temperature and heat flux. The results are presented with flow configurations and isotherms, local and average Nusselt number along the cold wall for different Darcy numbers from 10⁻¹ to 10⁻⁶, porosity values from 0.2 to 0.8, Rayleigh numbers from 10³ to 10⁷, and the ratio of porous layer thickness to cavity height from 0 to 0.50. The flow pattern inside the cavity is affected with these parameters and hence the local and global heat transfer. A modified Darcy–Rayleigh number is proposed for the heat convection intensity in porous/fluid filled domains. When its value is less than unit, global heat transfer keeps unchanged. The interfacial stress jump coefficients β ₁ and β ₂ were varied from  −1 to +1, and their effects on the local and average Nusselt numbers, velocity and temperature profiles in the mid-width of the cavity are investigated.     

A Modified Nested-Gridding for Upscaling–Downscaling in Reservoir Simulation

This article reports a numerical study of double-diffusive convection in a fluid-saturated vertical porous annulus subjected to discrete heat and mass fluxes from a portion of the inner wall. The outer wall is maintained at uniform temperature and concentration, while the top and bottom walls are adiabatic and impermeable to mass transfer. The physical model for the momentum equation is formulated using the Darcy law, and the resulting governing equations are solved using an implicit finite difference technique. The influence of physical and geometrical parameters on the streamlines, isotherms, isoconcentrations, average Nusselt and Sherwood numbers has been numerically investigated in detail. The location of heat and solute source has a profound influence on the flow pattern, heat and mass transfer rates in the porous annulus. For the segment located at the bottom portion of inner wall, the flow rate is found to be higher, whereas the heat and mass transfer rates are higher when the source is placed near the middle of the inner wall. Further, the average Sherwood number increases with Lewis number, while for the average Nusselt number the effect is opposite. The average Nusselt number increases with radius ratio (λ); however, the average Sherwood number increases with radius ratio only up to λ = 5, and for λ > 5 , the average Sherwood number does not increase significantly.     

The influence of the physical properties ratios on the conjugate heat transfer from a drop

This paper analyses the influence of the conductivity ratio, Φ_λ, and the volume heat capacity ratio, Φ_h, on the conjugate heat transfer from a liquid particle in a liquid environment. Both creeping flow and moderate Re number domain are considered. Special attention is given to the phenomenon of thermal wake. The occurrence and the evolution of the thermal wake depend on the values of volume heat capacity ratio and conductivity ratio respectively. The influence of the Pe numbers on the thermal inversion phenomenon and the interaction (at moderate Re number values) between thermal wake and flow separation are analysed. The results obtained show that Φ_λ and Φ_h influence strongly the conjugate heat transfer. Received on 11 January 1999     

Numerical Study of Heat Transfer in a Rectangular Channel with Porous Covering Obstacles

A numerical study is performed to analyze steady laminar forced convection in a channel in which discrete heat sources covered with porous material are placed on the bottom wall. Hydrodynamic and heat transfer results are reported. The flow in the porous medium is modeled using the Darcy–Brinkman–Forchheimer model. A computer program based on control volume method with appropriate averaging for diffusion coefficient is developed to solve the coupling between solid, fluid, and porous region. The effects of parameters such as Reynolds number, Prandtl number, inertia coefficient, and thermal conductivity ratio are considered. The results reveal that the porous cover with high thermal conductivity enhances the heat transfer from the solid blocks significantly and decreases the maximum temperature on the heated solid blocks. The mean Nusselt number increases with increase of Reynolds number and Prandtl number, and decrease of inertia coefficient. The pressure drop along the channel increases rapidly with the increase of Reynolds number.     

A numerical study of the steady forced convection heat transfer from an unconfined circular cylinder

Forced convection heat transfer from an unconfined circular cylinder in the steady cross-flow regime has been studied using a finite volume method (FVM) implemented on a Cartesian grid system in the range as 10 ≤ Re ≤ 45 and 0.7 ≤ Pr ≤ 400. The numerical results are used to develop simple correlations for Nusselt number as a function of the pertinent dimensionless variables. In addition to average Nusselt number, the effects of Re, Pr and thermal boundary conditions on the temperature field near the cylinder and on the local Nusselt number distributions have also been presented to provide further physical insights into the nature of the flow. The rate of heat transfer increases with an increase in the Reynolds and/or Prandtl numbers. The uniform heat flux condition always shows higher value of heat transfer coefficient than the constant wall temperature at the surface of the cylinder for the same Reynolds and Prandtl numbers. The maximum difference between the two values is around 15–20%.     

Non-Darcian and Anisotropic Effects on Free Convection in a Porous Enclosure

The free convective flow and heat transfer, within the framework of Boussinesq approximation, in an anisotropic fluid filled porous rectangular enclosure subjected to end-to-end temperature difference have been investigated using Brinkman extended non-Darcy flow model. The studies involve simultaneous consideration of hydrodynamic and thermal anisotropy. The flow and temperature fields in general are governed by, Ra, the Rayleigh number, AR, the aspect ratio of the slab, K*, the permeability ratio and k*, the thermal conductivity ratio, and Da, Darcy number. Numerical solutions employing the successive accelerated replacement (SAR) scheme have been obtained for 100 ≤ Ra ≤ 1000, 0.5 ≤ AR ≤ 5, 0.5 ≤ K* ≤ 5, 0.5 ≤ k* ≤ 5, and 0 ≤ Da ≤ 0.1. It has been found that [`(Nu)]{\overline {Nu}}, average Nusselt number increases with increase in K* and decreases as k* increases. However, the magnitude of the change in [`(Nu)]{\overline {Nu}} depends on the parameter Da, characterizing the Brinkman extended non-Darcy flow.     

Combined heat and mass transfer along a vertical moving cylinder with a free stream

The mixed convection flow over a continuous moving vertical slender cylinder under the combined buoyancy effect of thermal and mass diffusion has been studied. Both uniform wall temperature (concentration) and uniform heat (mass) flux cases are included in the analysis. The problem is formulated in such a manner that when the ratio λ(= u _w/(u _w + u _∞), where u _w and u _∞ are the wall and free stream velocities, is zero, the problem reduces to the flow over a stationary cylinder, and when λ = 1 it reduces to the flow over a moving cylinder in an ambient fluid. The partial differential equations governing the flow have been solved numerically using an implicit finite-difference scheme. We have also obtained the solution using a perturbation technique with Shanks transformation. This transformation has been used to increase the range of the validity of the solution. For some particular cases closed form solutions are obtained. The surface skin friction, heat transfer and mass transfer increase with the buoyancy forces. The buoyancy forces cause considerable overshoot in the velocity profiles. The Prandtl number and the Schmidt number strongly affect the surface heat transfer and the mass transfer, respectively. The surface skin friction decreases as the relative velocity between the surface and free stream decreases. Received on 17 May 1999     

The optimal dimensions of convective-radiating circular fins

The optimal dimensions of convective-radiating circular fins with variable profile, heat-transfer coefficient and thermal conductivity, as well as internal heat generation are obtained. A profile of the form y=(w/2) [1+(r _o/r) ⁿ ] is studied, while variation of thermal conductivity is of the form k=k _o[1+ɛ((T−T _∞)/ (T _b−T _∞)) ^m ]. The heat-transfer coefficient is assumed to vary according to a power law with distance from the bore, expressed as h=K[(r−r _o)/(r _e−r _o)]^λ. The results for λ=0 to λ=1.9, and −0.4≤ɛ≤0.4, have been expressed by suitable dimensionless parameters. A correlation for the optimal dimensions of a constant and variable profile fins is presented in terms of reduced heat-transfer rate. It is found that a (quadratic) hyperbolic circular fin with n=2 gives an optimum performance. The effect of radiation on the fin performance is found to be considerable for fins operating at higher base temperatures, whereas the effect of variable thermal conductivity on the optimal dimensions is negligible for the variable profile fin. It is also observed, in general, that the optimal fin length and the optimal fin base thickness are greater when compared to constant fin thickness. Received on 22 February 1999     

Double-diffusive convection for a heated cylinder submerged in a salt-stratified fluid layer

Double-diffusive convection due to a cylindrical source submerged in a salt-stratified solution is numerically investigated in this study. For proper simulation of the vortex generated around the cylinder, a computational domain with irregular shape is employed. Flow conditions depend strongly on the thermal Rayleigh number, Ra _T , and the buoyancy ratio, R _ρ. There are two types of onset of instability existing in the flow field. Both types are due to either the interaction of the upward temperature gradient and downward salinity gradient or the interaction of the lateral temperature gradient and downward salinity gradient. The onset of layer instability due to plume convection is due to the former, whereas, the onset of layer instability of layers around the cylinder is due to the latter. Both types can be found in the flow field. The transport mechanism of layers at the top of the basic plume belongs to former while that due to basic plume and layer around the cylinder are the latter. The increase in Ra _T reinforces the plume convection and reduces the layer numbers generated around the cylinder for the same buoyancy ratio. For the same Ra _T , the increase of R _ρ suppresses the plume convection but reinforces the layers generated around the cylinder. The profiles of local Nusselt number reflects the heat transfer characteristics of plume convection and layered structure. The profiles of averaged Nusselt number are between the pure conduction and natural convection modes and the variation is due to the evolution of layers. Received on 13 September 1996     

Steady and Unsteady Heat Transfer in a Channel Partially Filled with Porous Media Under Thermal Non-Equilibrium Condition

Steady and pulsatile flow and heat transfer in a channel lined with two porous layers subject to constant wall heat flux under local thermal non-equilibrium (LTNE) condition is numerically investigated. To do this, a physical boundary condition in the interface of porous media and clear region of the channel is derived. The objective of this work is, first, to assess the effects of local solid-to-fluid heat transfer (a criterion indicating on departure from local thermal equilibrium (LTE) condition), solid-to-fluid thermal conductivity ratio and porous layer thickness on convective heat transfer in steady condition inside a channel partially filled with porous media; second, to examine the impact of pulsatile flow on heat transfer in the same channel. The effects of LTNE condition and thermal conductivity ratio in pulsatile flow are also briefly discussed. It is observed that Nusselt number inside the channel increases when the problem is tending to LTE condition. Therefore, careless consideration of LTE may lead to overestimation of heat transfer. Solid-to-fluid thermal conductivity ratio is also shown to enhance heat transfer in constant porous media thickness. It is also revealed that an increase in the amplitude of pulsation may result in enhancement of Nusselt number, while Nusselt number has a minimum in a certain frequency for each value of amplitude.     

Effect of an Inserted Porous Layer Located at a Wall of a Parallel Plate Channel on Forced Convection Heat Transfer

A theoretical study is performed on heat and fluid flow in partially porous medium filled parallel plate channel. A uniform symmetrical heat flux is imposed onto the boundaries of the channel partially filled with porous medium. The dimensional forms of the governing equations are solved numerically for different permeability and effective thermal conductivity ratios. Then, the governing equations are made dimensionless and solved analytically. The results of two approaches are compared and an excellent agreement is observed, indicating correctness of the both solutions. An overall Nusselt number is defined based on overall thermal conductivity and difference between the average temperature of walls and mean temperature to compare heat transfer in different channels with different porous layer thickness, Darcy number, and thermal conductivity ratio. Moreover, individual Nusselt numbers for upper and lower walls are also defined and obtained. The obtained results show that the maximum overall Nusselt number is achieved for thermal conductivity ratio of 1. At specific values of Darcy number and thermal conductivity ratio, individual Nusselt numbers approach to infinity since the value of wall temperatures approaches to mean temperature.