Effect of cylindrical cavity height on laser-induced breakdown spectroscopy with spatial confinement

In this paper,we present a study on the spatial confinement effect of laser-induced plasma with a cylindrical cavity in laser-induced breakdown spectroscopy(LIBS).The emission intensity with the spatial confinement is dependent on the height of the confinement cavity.It is found that,by selecting the appropriate height of cylindrical cavity,the signal enhancement can be significantly increased.At the cylindrical cavity(diameter = 2 mm) with a height of 6 mm,the enhancement ratio has the maximum value(approximately 8.3),and the value of the relative standard deviation(RSD)(7.6%) is at a minimum,the repeatability of LIBS signal is best.The results indicate that the height of confinement cavity is very important for LIBS technique to reduce the limit of detection and improve the precision.     

Comparison of emission signals for different polarizations in femtosecond laser-induced breakdown spectroscopy

In this study, a femtosecond laser was focused to ablate brass target and generate plasma emission in air. The influence of lens to sample distance(LTSD) on spectral emission of brass plasma under linearly and circularly polarized pulses with different pulse energies was investigated. The results indicated that the position with the strongest spectral emission moved toward focusing lens with increasing the energy. At the same laser energy, the line emission under circularly polarized pulse was stronger compared with linearly polarized pulse for different LTSDs. Next, electron temperature and density of the plasma were obtained with Cu(Ⅰ) lines,indicating that the electron temperature and density under circularly polarized pulse were higher compared to that under linearly polarized pulse. Therefore, changing the laser polarization is a simple and effective way to improve the spectral emission intensity of femtosecond laserinduced plasma.     

Effect of lens focusing distance on laser-induced silicon plasmas at different sample temperatures

We investigated the dependence of laser-induced breakdown spectral intensity on the focusing position of a lens at different sample temperatures(room temperature to 300 ℃) in atmosphere.A Q-switched Nd:YAG nanosecond pulsed laser with 1064 nm wavelength and 10 ns pulse width was used to ablate silicon to produce plasma. It was confirmed that the increase in the sample's initial temperature could improve spectral line intensity. In addition, when the distance from the target surface to the focal point increased, the intensity firstly rose, and then dropped.The trend of change with distance was more obvious at higher sample temperatures. By observing the distribution of the normalized ratio of Si atomic spectral line intensity and Si ionic spectral line intensity as functions of distance and temperature, the maximum value of normalized ratio appeared at the longer distance as the initial temperature was higher, while the maximum ratio appeared at the shorter distance as the sample temperature was lower.     

Distinguish Fritillaria cirrhosa and nonFritillaria cirrhosa using laser-induced breakdown spectroscopy

As traditional Chinese medicines, Fritillaria from different origins are very similar and it is difficult to distinguish them. In this study, the laser-induced breakdown spectroscopy combined with learning vector quantization(LIBS-LVQ) was proposed to distinguish the powdered samples of Fritillaria cirrhosa and non-Fritillaria cirrhosa. We also studied the performance of linear discriminant analysis, and support vector machine on the same data set. Among these three classifiers, LVQ had the highest correct classification rate of 99.17%. The experimental results demonstrated that the LIBS-LVQ model could be used to differentiate the powdered samples of Fritillaria cirrhosa and non-Fritillaria cirrhosa.     

Temporal and spatial evolution measurement of laser-induced breakdown spectroscopy on hydrogen retention in tantalum

Fuel retention measurement on plasma-facing components is an active field of study in magnetic confinement nuclear fusion devices.The laser-induced breakdown spectroscopy(LIBS)diagnostic method has been well demonstrated to detect the elemental distribution in PFCs.In this work,an upgraded co-axis LIBS system based on a linear fiber bundle collection system has been developed to measure the hydrogen(H) retention on a tantalum(Ta) sample under a vacuum condition.The spatial resolution measurement of the different positions of the LIBS plasma can be achieved simultaneously with varying delay times.The temporal and spatial evolution results of LIBS plasma emission show that the H plasma observably expands from the delay times of 0-200 ns.The diameter of Ta plasma is about 6 mm which is much less than the size of H plasma after 200 ns.The difference in the temporal and spatial evolution behaviors between H plasma and Ta plasma is due to the great difference in the atomic mass of H and Ta.The depth profile result shows that H retention mainly exists on the surface of the sample.The temporal and spatial evolution behaviors of the electron excited temperature are consistent with that of the Ta emission.The result will further improve the understanding of the evolution of the dynamics of LIBS plasma and optimize the current collection system of in situ LIBS in fusion devices.     

Comparison of sample temperature effect on femtosecond and nanosecond laser-induced breakdown spectroscopy

In this paper, we investigated the emission spectra of plasmas produced from femtosecond and nanosecond laser ablations at different target temperatures in air. A brass was selected as ablated target of the experiment. The results indicated that spectral emission intensity and plasma temperature showed similar trend for femtosecond and nanosecond lasers, and the two parameters were improved by increasing the sample temperature in both cases. Moreover, the temperature of nanosecond laser-excited plasma was higher compared with that of femtosecond laser-excited plasma, and the increase of the plasma temperature in the case of nanosecond laser was more evident. In addition, there was a significant difference in electron density between femtosecond and nanosecond laser-induced plasmas. The electron density for femtosecond laser decreased with increasing the target temperature, while for nanosecond laser, the electron density was almost unchanged at different sample temperatures.     

Cluster analysis of polymers using laser-induced breakdown spectroscopy with K-means

Laser-induced breakdown spectroscopy(LIBS) combined with K-means algorithm was employed to automatically differentiate industrial polymers under atmospheric conditions.The unsupervised learning algorithm K-means were utilized for the clustering of LIBS dataset measured from twenty kinds of industrial polymers.To prevent the interference from metallic elements,three atomic emission lines(C I 247.86 nm,H I 656.3 nm,and O I 777.3 nm) and one molecular line C–N(0,0) 388.3 nm were used.The cluster analysis results were obtained through an iterative process.The Davies–Bouldin index was employed to determine the initial number of clusters.The average relative standard deviation values of characteristic spectral lines were used as the iterative criterion.With the proposed approach,the classification accuracy for twenty kinds of industrial polymers achieved 99.6%.The results demonstrated that this approach has great potential for industrial polymers recycling by LIBS.     

Improvement in classification accuracy of stainless steel alloys by laser-induced breakdown spectroscopy based on elemental intensity ratio analysis

Laser-induced breakdown spectroscopy(LIBS) is a useful technique for accurate sorting of metal scrap by chemical composition analysis.In this work,a method for intensity-ratiobased LIBS classification of stainless steel applicable to highly fluctuating LIBS signal conditions is proposed.The spectral line pairs for intensity ratio calculation are selected according to elemental concentration and upper levels of emission lines.It is demonstrated that the classification accuracy can be significantly improved from that of full-spectra principal component analysis or intensity-based analysis.The proposed method is considered to be suited to an industrial scrap sorting system that requires minimal maintenance and low system price.     

Quantitative analysis of steel and iron by laser-induced breakdown spectroscopy using GA-KELM

According to the multiple researches in the last couple of years, laser-induced breakdown spectroscopy(LIBS) has shown a great potential for rapid analysis in steel industry.Nevertheless, the accuracy and precision may be limited by complex matrix effect and selfabsorption effect of LIBS seriously. A novel multivariate calibration method based on genetic algorithm-kernel extreme learning machine(GA-KELM) is proposed for quantitative analysis of multiple elements(Si, Mn, Cr, Ni, V, Ti, Cu, Mo) in forty-seven certified steel and iron samples.First, the standardized peak intensities of selected spectra lines are used as the input of model.Then, the genetic algorithm is adopted to optimize the model parameters due to its obvious capability in finding the global optimum solution. Based on these two steps above, the kernel method is introduced to create kernel matrix which is used to replace the hidden layer's output matrix. Finally, the least square is applied to calculate the model's output weight. In order to verify the predictive capability of the GA-KELM model, the R-square factor(R~2), Root-meansquare Errors of Calibration(RMSEC), Root-mean-square Errors of Prediction(RMSEP) of GAKELM model are compared with the traditional PLS algorithm, respectively. The results confirm that GA-KELM can reduce the interference from matrix effect and self-absorption effect and is suitable for multi-elements calibration of LIBS.     

A novel strategy for quantitative analysis of soil pH via laser-induced breakdown spectroscopy coupled with random forest

pH is one of the significant properties of soil,and is closely related to the decomposition of soil organic matter,anion-cation balance,growth of plants and many other soil processes.In the present work,laser-induced breakdown spectroscopy(LIBS) technique coupled with random forest(RF) was proposed to quantify the pH of soil.First,LIBS spectra of soil was collected,and some common elements in soil were identified based on the National Institute of Science and Technology database.Then,in order to obtain a better predictive result,the influence of different input variables(full spectrum,different spectral ranges,the intensity of characteristic bands and characteristic lines) on the predictive performance of RF calibration model was explored with the evaluation indicators of root mean square error(RMSE) and coefficient of determination(R2),the characteristic bands of four elements(AI,Ca,Mg and Si) were determined as the optimal input variables.Finally,the predictive performance of RF calibration model was compared with partial least squares calibration model with the optimal input variables and model parameters,and RF calibration model showed a better predictive performance,and the four evaluation indicators of R_p~2,RMSEP,mean absolute error and mean relative error were 0.9687,0.1285,0.1114 and 0.0136,respectively.It indicates that LIBS technique coupled with RF algorithm is an effective method for pH determination of soil.     

A rapid classification method of aluminum alloy based on laser-induced breakdown spectroscopy and random forest algorithm

As an important non-ferrous metal structural material most used in industry and production,aluminum(Al) alloy shows its great value in the national economy and industrial manufacturing.How to classify Al alloy rapidly and accurately is a significant, popular and meaningful task.Classification methods based on laser-induced breakdown spectroscopy(LIBS) have been reported in recent years. Although LIBS is an advanced detection technology, it is necessary to combine it with some algorithm to reach the goal of rapid and accurate classification. As an important machine learning method, the random forest(RF) algorithm plays a great role in pattern recognition and material classification. This paper introduces a rapid classification method of Al alloy based on LIBS and the RF algorithm. The results show that the best accuracy that can be reached using this method to classify Al alloy samples is 98.59%, the average of which is 98.45%. It also reveals through the relationship laws that the accuracy varies with the number of trees in the RF and the size of the training sample set in the RF. According to the laws, researchers can find out the optimized parameters in the RF algorithm in order to achieve,as expected, a good result. These results prove that LIBS with the RF algorithm can exactly classify Al alloy effectively, precisely and rapidly with high accuracy, which obviously has significant practical value.     

The classification of plants by laser-induced breakdown spectroscopy based on two chemometric methods

The applications of laser-induced breakdown spectroscopy(LIBS) on classifying complex natural organics are relatively limited and their accuracy still requires improvement.In this work,to study the methods on classification of complex organics,three kinds of fresh leaves were measured by LIBS.100 spectra from 100 samples of each kind of leaves were measured and then they were divided into a training set and a test set in a ratio of 7:3.Two algorithms of chemometric methods including the partial least squares discriminant analysis(PLS-DA) and principal component analysis Mahalanobis distance(PCA-MD) were used to identify these leaves.By using 23 lines from 16 elements or molecules as input data,these two methods can both classify these three kinds of leaves successfully.The classification accuracies of training sets are both up to 100% by PCA-MD and PLS-DA.The classification accuracies of the test set are 93.3% by PCA-MD and 97.8% by PLS-DA.It means that PLS-DA is better than PCA-MD in classifying plant leaves.Because the components in PLS-DA process are more suitable for classification than those in PCA-MD process.We think that this work can provide a reference for plant traceability using LIBS.     

Elemental and proximate analysis of coal by x-ray fluorescence assisted laser-induced breakdown spectroscopy

Although laser-induced breakdown spectroscopy (LIBS), as a fast on-line analysis technology, has great potential and competitiveness in the analysis of chemical composition and proximate analysis results of coal in thermal power plants, the measurement repeatability of LIBS needs to be further improved due to the difficulty in controlling the stability of the generated plasmas at present. In this paper, we propose a novel x-ray fluorescence (XRF) assisted LIBS method for high repeatability analysis of coal quality, which not only inherits the ability of LIBS to directly analyze organic elements such as C and H in coal, but also uses XRF to make up for the lack of stability of LIBS in determining other inorganic ash-forming elements. With the combination of elemental lines in LIBS and XRF spectra, the principal component analysis and the partial least squares are used to establish the prediction model and perform multi-elemental and proximate analysis of coal. Quantitative analysis results show that the relative standard deviation (RSD) of C is 0.15%, the RSDs of other elements are less than 4%, and the standard deviations of calorific value, ash content, sulfur content and volatile matter are 0.11 MJ kg−1, 0.17%, 0.79% and 0.41% respectively, indicating that the method has good repeatability in determination of coal quality. This work is helpful to accelerate the development of LIBS in the field of rapid measurement of coal entering the power plant and on-line monitoring of coal entering the furnace.     

Laser-induced breakdown spectroscopy for the classification of wood materials using machine learning methods combined with feature selection

In this paper, we explore whether a feature selection method can improve model performance by using some classical machine learning models, artificial neural network, k-nearest neighbor,partial least squares-discrimination analysis, random forest, and support vector machine(SVM),combined with the feature selection methods, distance correlation coefficient(DCC), important weight of linear discriminant analysis(IW-LDA), and Relief-F algorithms, to discriminate eight species of wood(African rosewood, Brazilian bubinga, elm, larch, Myanmar padauk,Pterocarpus erinaceus, poplar, and sycamore) based on the laser-induced breakdown spectroscopy(LIBS) technique. The spectral data are normalized by the maximum of line intensity and principal component analysis is applied to the exploratory data analysis. The feature spectral lines are selected out based on the important weight assessed by DCC, IW-LDA,and Relief-F. All models are built by using the different number of feature lines(sorted by their important weight) as input. The relationship between the number of feature lines and the correct classification rate(CCR) of the model is analyzed. The CCRs of all models are improved by using a suitable feature selection. The highest CCR achieves(98.55...0.39)% when the SVM model is established from 86 feature lines selected by the IW-LDA method. The result demonstrates that a suitable feature selection method can improve model recognition ability and reduce modeling time in the application of wood materials classification using LIBS.     

Detection of K in soil using time-resolved laser-induced breakdown spectroscopy based on convolutional neural networks

One of the technical bottlenecks of traditional laser-induced breakdown spectroscopy (LIBS) is the difficulty in quantitative detection caused by the matrix effect. To troubleshoot this problem, this paper investigated a combination of time-resolved LIBS and convolutional neural networks (CNNs) to improve K determination in soil. The time-resolved LIBS contained the information of both wavelength and time dimension. The spectra of wavelength dimension showed the characteristic emission lines of elements, and those of time dimension presented the plasma decay trend. The one-dimensional data of LIBS intensity from the emission line at 766.49 nm were extracted and correlated with the K concentration, showing a poor correlation of R²_c=0.0967, which is caused by the matrix effect of heterogeneous soil. For the wavelength dimension, the two-dimensional data of traditional integrated LIBS were extracted and analyzed by an artificial neural network (ANN), showing R²_v=0.6318 and the root mean square error of validation (RMSEV)=0.6234. For the time dimension, the two-dimensional data of time-decay LIBS were extracted and analyzed by ANN, showing R²_v=0.7366 and RMSEV=0.7855. These higher determination coefficients reveal that both the non-K emission lines of wavelength dimension and the spectral decay of time dimension could assist in quantitative detection of K. However, due to limited calibration samples, the two-dimensional models presented over-fitting. The three-dimensional data of time-resolved LIBS were analyzed by CNNs, which extracted and integrated the information of both the wavelength and time dimension, showing the R²_v=0.9968 and RMSEV=0.0785. CNN analysis of time-resolved LIBS is capable of improving the determination of K in soil.     

Quantitative analysis of C,Si, Mn,Ni, Cr and Cu in low-alloy steel under ambient conditions via laser-induced breakdown spectroscopy

A diode-pumped solid-state laser(DPSSL) with a high energetic stability and long service life is applied to ablate the steel samples instead of traditional Nd:YAG laser pumped by a xenon lamp,and several factors, such as laser pulse energy, repetition rate and argon flow rate, that influence laser-induced breakdown spectroscopy(LIBS) analytical performance are investigated in detail.Under the optimal experiment conditions, the relative standard deviations for C, Si, Mn, Ni, Cr and Cu are 3.3%–8.9%, 0.9%–2.8%, 1.2%–4.1%, 1.7%–3.0%, 1.1%–3.4% and 2.5%–8.5%,respectively, with the corresponding relative errors of 1.1%–7.9%, 1.0%–6.3%, 0.4%–3.9%,1.5%–6.3%, 1.2%–4.0% and 1.2%–6.4%. Compared with the results of the traditional spark discharge optical emission spectrometry technique, the analytical performance of LIBS is just a little inferior due to the less stable laser-induced plasma and smaller amount of ablated sample by the laser. However, the precision, detection limits and accuracy of LIBS obtained in our present work were sufficient to meet the requirements for process analysis. These technical performances of higher stability of output energy and longer service life for DPSSL, in comparison to the Q-switch laser pumped by xeon lamp, qualify it well for the real time online analysis for different industrial applications.     

Time-resolved spectroscopy of femtosecond laser-induced Cu plasma with spark discharge

The combination of spark discharge and laser-induced breakdown spectroscopy (LIBS) is called spark discharge assisted LIBS. It works under laser-plasma triggered spark discharge mode, and shows its ability to enhance spectral emission intensity. This work uses a femtosecond laser as the light source, since femtosecond laser has many advantages in laser-induced plasma compared with nanosecond laser, meanwhile, the study on femtosecond LIBS with spark discharge is rare. Time-resolved spectroscopy of spark discharge assisted femtosecond LIBS was investigated under different discharge voltages and laser energies. The results showed that the spectral intensity was significantly enhanced by using spark discharge compared with LIBS alone. And, the spectral emission intensity using spark discharge assisted LIBS increased with the increase in the laser energy. In addition, at low laser energy, there was an obvious delay on the discharge time compared with high laser energy, and the discharge time with positive voltage was different from that with negative voltage.     

Signal processing for real-time identification of similar metals by laser-induced breakdown spectroscopy

Laser-induced breakdown spectroscopy(LIBS) is regarded as a promising technique for realtime sorting of scrap metals due to its capability of fast multi-elemental and in-air analysis. This work reports a method for signal processing which ensures high accuracy and high speed during similar metal sorting by LIBS. Similar metals such as aluminum alloys or stainless steel are characterized by nearly the same constituent elements with slight variations in elemental concentration depending on metal type. In the proposed method, the original data matrix is substantially reduced for fast processing by selecting new input variables(spectral lines) using the information for the constituent elements of similar metals. Specifically, principal component analysis(PCA) of full-spectra LIBS data was performed and then, based on the loading plots, the input variables of greater significance were selected in the order of higher weights for each constituent element. The results for the classification test with aluminum alloy, copper alloy,stainless steel and cast steel showed that the classification accuracy of the proposed method was nearly the same as that of full-spectra PCA, but the computation time was reduced by a factor of 20 or more. The results demonstrated that incorporating the information for constituent elements can significantly accelerate classification speed without loss of accuracy.     

Study of pressure effects on ocean in-situ detection using laser-induced breakdown spectroscopy

Laser-induced breakdown spectroscopy (LIBS) has attracted extensive attention as a new technique for in-situ marine application. In this work, the influence of deep-sea high pressure environment on LIBS signals was investigated by using a compact LIBS-sea system developed by Ocean University of China for the in-situ chemical analysis of seawater. The results from the field measurements show that the liquid pressure has a significant effect on the LIBS signals. Higher peak intensity and larger line broadening were obtained as the pressure increases. By comparing the variations of the temperature and salinity with the LIBS signals, a weak correlation between them can be observed. Under high pressure conditions, the optimal laser energy was higher than that in air environment. When the laser energy exceeded 17 mJ, the effect of laser energy on the signal intensity weakened. The signal intensity decreases gradually at larger delays. The obtained results verified the feasibility of the LIBS technique for the deep-sea in-situ detection, and we hope this technology can contribute to surveying more deep-sea environments such as the hydrothermal vent regions.     

Investigation of the factors affecting the limit of detection of laser-induced breakdown spectroscopy for surface inspection

Laser-induced breakdown spectroscopy(LIBS) was examined to detect a trace substance adhered onto Al alloys for the surface inspection of materials to be adhesively bonded. As an example of Si contamination, silicone oil was employed and sprayed onto substrates with a controlled surface concentration. LIBS measurements employing nanosecond UV pulses(λ?=?266 nm) and an off-axis emission collection system with different detecting heights were performed. Because surface contaminants are involved in the plasma formed by laser ablation of the substrates, the relative contribution of the surface contaminants and the substrates to the plasma emission could be changed depending on the conditions for plasma formation. The limit of detection(LOD) was evaluated under several detecting conditions for investigating the factors that affected the LOD. A significant factor was the standard deviation values of signal intensities obtained for the clean substrates. This value varied depending on the measurement conditions.For the Al alloy(A6061), the smallest LOD obtained was 0.529 μg?·?cm~(-2). Furthermore, an improved LOD(0.299 μg?·?cm~(-2)) was obtained for the Al alloy with a lower Si content.