土钉抗拔承载力的原位试验研究

根据土钉现场抗拔试验数据,分析了钉材、浆液龄期等因素对土钉抗拔承载力的影响,建议了合理的下层土钉开挖时间。最后通过试验土钉抗拔力反算土体与锚固体的极限粘结强度,并与规范推荐值进行了比较。     

Internal soil moisture response to rainfall-induced slope failures and debris discharge

Predictions of rainfall-induced fast-moving mass flow and/or debris flows require better knowledge of the mechanism controlling the debris discharge of slopes in debris source areas. A series of rainfall tests on 0.32 m-deep, 0.7 m-high, 1.35 m-wide sandy slopes resting on a bi-linear impermeable rigid base was performed. Soil moisture content and solid discharge measurements were performed to gain insights into the rainfall-induced retrogressive slope failure. The solid (or debris) discharge is a result of the wash-out of the fluidized slope toe by the interflow along the soil–bedrock interface. Characteristics of the failure process for the slopes are represented by mass wasting curves or ‘solid discharge (Q_s) vs. time (t)’ curves which are functions of the rainfall intensity and/or the cumulative rainfall. The mass wasting curves have inflection points representing transitions from minor toe failures into remarkable retrogressive failures. The first inflection point of the soil moisture (ω) vs. t curve measured at the soil–bedrock interface signaling the arrival of the descending ‘wet front’, may serve as a precursor for predicting the onset of an abrupt solid discharge induced by shallow slope failures. The time of peak water content measured at the soil–bedrock interface may approximate the time of 5% total solid volume discharge. Up to the time of 5% of total slope volume discharge, a fully saturated state (S_r  100%) was never observed at the 0.2 m-below-surface zone; however, it was observed along the soil–bedrock interface at near-toe zone of the slope, regardless of the intensity of rainfall investigated. Retrogressive failures were essentially associated with nonuniformly distributed water content in the slope. For both the 0.2 m-below-surface zone and the soil–bedrock interface, a more uniform distribution of S_r along the full height of the slope was found for slopes subjected to high rainfall intensities of 47 and 65 mm/h than that for the slope subjected to a low rainfall intensity of 23 mm/h. At the inflection point of the Q_s vs. t curve and 5% of total solid volume discharge, values of S_r at a certain distance from the toe for the soil–bedrock interface were higher than those measured at the same distance from the toe for the 0.2 m-below-surface zone, indicating the effect of infiltration-induced interflow along the soil–bedrock interface and its effects on the fluidization of the slope toe and the retrogressive failure of the slope.     

Influences of overburden pressure and soil dilation on soil nail pull-out resistance

Soil nailing is the most popular technique for stabilizing newly formed and existing sub-standard slopes in Hong Kong because of its economic and technical advantages. The nail–soil interface shear resistance is an important parameter in design of soil nailed structures. A three-dimensional finite element model was established and used for simulating soil nail pull-out tests. The finite element model was verified by comparing simulated results with measured data. The agreement between the experimental and simulated results in terms of both average pull-out shear stress and stress variation was very good. Using this finite element model, a parametric study was carried out to study the influences of the overburden pressure and soil dilation angle on the soil nail pull-out resistance. The simulated peak pull-out resistance was not directly related to the overburden pressure, which was coincident with the observations in laboratory pull-out tests. The simulated pull-out resistance increased significantly with the increase in dilation angle of the shearing zone. This analysis indicated that the constrained dilatancy of the nail–soil interface and the soil surrounding the nail contributed a lot to the development of peak pull-out resistance.     

上覆压力和剪胀作用下土钉抗拔的有限元模拟

灌浆土钉在边坡加固工程中有着广泛的应用。土钉在不同条件下的抗拔机制仍是进一步研究的课题。通过建立一个三维有限元模型,研究土钉在不同上覆压力和剪胀作用下的土钉抗拔行为。采用摩尔-库仑模型模拟花岗岩土,土与土钉界面采用“接触对”和库仑摩擦模型描述。模型可以模拟土钉发生较大抗拔位移下发生滑移破坏的过程。模型参数通过三轴试验结果进行校正。通过与大尺寸室内抗拔试验结果相比较,验证了模型的有效性。模型展现了土钉在钻孔后和抗拔过程中土钉周围的土压力的变化。最后通过参数分析,研究了上覆压力和剪胀对土钉抗拔力的影响。结果显示,当上覆压力较小时,剪胀角对抗拔应力的影响较小。随着上覆压力的增加,剪胀角对抗拔应力的影响变得更加明显。     

入渗条件下某非饱和土坡稳定性的动态分析

土坡在进行稳定性计算时传统的极限平衡分析方法对于同一土体多采用单一的土体强度参数。近年来,人们致力于土体含水量与抗剪强度之间的关系研究,试验证明不同的含水量下土体的抗剪强度指标有很大变化。在连续的降雨条件下,在土体内部形成渗流改变土体的含水量会引起抗剪强度的变化,随时间和渗入量的不同土坡稳定性将随之改变。基于降雨条件下边坡饱和—非饱和渗流计算,利用土水分离土条自重法计算在不同时刻土坡的动态稳定系数,同时分析潜在滑动面的变化规律。     

杆系有限元法求解复合土钉支护结构的位移

复合土钉支护位移计算尚未有成熟的分析方法。本文采用杆系有限单元法,结合支护土钉滞后的施工动态分析,来求解施工超前桩墙的复合土钉支护结构的水平位移。坑外侧主动土压力,由于受到密集土钉作用和坡角的影响,考虑折减计算。本分析方法简便,易于计算机编程。通过工程实例计算和分析,结果表明水平位移计算值与实测值较为接近。     

Numerical and experimental studies of the mechanical behaviour for compaction grouted soil nails in sandy soil

A model test was conducted for a newly developed soil nail, the result of which was compared to that of a 3D finite element method (FEM) simulation. The shape angle (β) and friction coefficients (μ) contributed to the difference in pull-out force between the model test and the simulation. Further verifications were conducted, during which the pull-out mechanisms of the soil nail for different β and μ were analysed. It was found that both β and μ have a positive influence on the pull-out force; β only affects the increase rate, while μ influences the overall pull-out force level. Three components were found to govern the pull-out force, with the component applied to the expanded cement bulk surface accounting for approximately 80% of the total. This study proves that the optimal approach for increasing pull-out force is to enlarge the diameter of the cement bulk rather than extend the nail length.     

A comparative review of commercially-available software for soil slope stability analysis

Summary The main purpose of this paper is to carry out a comparative review of four commercial computer programs for the stability analysis of soil slopes. The review is carried out in two parts and should prove useful for potential users of the software. Part I reviews the facilities offered in terms of the range of limit equilibrium methods, the geotechnical modelling abilities, the operational features and the supporting documentation, and includes a general impression of friendliness. Part II assesses the use, accuracy and validity of each program by presenting and discussing the results of a number of model tests. Also included is a brief discussion of slope stability analysis, in particular the limit equilibrium method. The requirements of a practical computer program for soil slope stability analysis are defined and then used as a means of assessing the effectiveness of each program.     

A simple soil model for low frequency cyclic loading

A three-dimensional elastoplastic soil constitutive model capable of capturing the response of granular soils under low-frequency cyclic loading is introduced and verified. The model is piecewise linear with a hyperbolic stress-strain relationship. The size of the hysteresis loop is controlled using different scaling factors with a shift in the backbone curve at load reversal. The model introduces a new algorithm to better capture the soil’s response upon reloading for plane strain. Model verification with experimental results at different scales shows that the model has good capabilities in capturing the response of granular soils under low frequency cyclic loading.     

基坑支护土钉力的简化增量计算法

针对目前基坑土钉支护中土钉力的计算提出一个增量计算法,结果表明,该方法计算的土钉力较符合工程实际。     

A new and simple stress-dependent water retention model for unsaturated soil

The water retention curve (WRC) is an important hydraulic property of unsaturated soil needed for seepage analysis. Experimental evidence shows that the WRC is affected by various factors such as net stress and soil type. Many attempts have been made to describe the effects of net stress by including the void ratio in a water retention model. But the void ratio (i.e., soil density) is not the only parameter altered by the application of net stress. The pore structure, including the pore size distribution, pore shape and pore orientation, is also changed. Thus the influence of net stress on the WRC should not be treated as equivalent to density effects. In this study, it is verified that the inclusion of the void ratio cannot adequately capture the effects of net stress on the water retention behaviour. A new and simple water retention model is thus developed by considering the stress effects on the void ratio as well as the pore structure. The model is then applied to simulate the WRCs of three different soils tested over a wide range of stress conditions, including isotropic and anisotropic stress conditions. The results show that better predictions of experimental data can be made by incorporating the effects of net stress on both the void ratio and the pore structure.     

预应力锚杆复合土钉墙支护体系增量解析方法

以预应力锚杆复合土钉支护体系受力变形为分析对象,假定潜在滑裂面为平面,并考虑土体分层开挖过程,将施加预应力作为一个施工工况,建立了预应力锚杆复合土钉支护体系受力变形的增量解析方法。锚杆预应力和设置位置影响分析表明,随着锚杆预应力值的增加,潜在滑裂面的倾角逐渐减小,对基坑整体稳定性的贡献先增大后减小;锚杆设置越低,增加预应力对基坑整体稳定性的贡献越大。通过实际基坑支护工程的数值模拟分析与施工过程监测结果的对比分析,验证了考虑预应力锚杆施工过程特点的复合土钉支护体系增量解析方法的合理性。     

摩擦型根-土作用模型

随着人们环境保护意识的增强,在边坡防护工程中采用植物护坡方式已经得到越来越多的认可。针对目前植物护坡技术理论水平落后于工程实践的状况,对根与土体的相互作用关系进行了探讨,建立了摩擦型根-土作用力学模型,并且实验结果验证了该模型的正确性。     

土质陡坡降雨侵蚀的数学模型及求解方法

建立了土质陡坡降雨侵蚀的数学模型,模型包括陡坡细沟间坡面流控制方程、变沟宽陡坡细沟流控制方程、陡坡细沟间坡面侵蚀泥沙连续方程及陡坡变沟宽细沟侵蚀泥沙连续方程。通过紊流冲击分布概率确定土壤剥蚀方程,确定了泥沙源/汇项的表达形式及细沟高程与宽度的表达式。通过有限元和有限差分相结合的方法求解该数学模型,利用有限单元法对数学模型的水动力方程、运动方程及泥沙连续方程进行空间上的离散,利用有限差分法解决时间域的问题,得出了顺序求解的数值计算公式及模型数值求解的具体方法和步骤。     

A mathematical model for predicting coupled heat and water movement in unsaturated soil

An investigation was conducted to develop a comprehensive moisture model for predicting non-isothermal moisture conditions in soils. An extensive literature review indicated that a model based on the Philip and de Vries equations for non-isothermal moisture movement and heat conduction would give the best results. By using numerical methods, the implicit finite difference approximations to the moisture movement and heat-transfer equations were programmed for computer solution of water content and temperature in the soil with time. Validation studies indicate that the moisture model can be used to predict accurately moisture conditions in the soil. The model was validated by using hydraulic data from laboratory studies conducted on soil columns compacted with AASHO A-3 and AASHO A-4 soil. The application of the moisture model to the study of non-isothermal moisture movement in the field is demonstrated. The influence of parameters such as water table depth, precipitation, and soil hydraulic properties on soil moisture content are shown by use of the moisture model. The model is shown to be applicable to a wide range of boundary conditions and that it predicts the moisture-temperature regime with time in soils utilizing climatic input data.     

A simple daily soil–water balance model for estimating the spatial and temporal distribution of groundwater recharge in temperate humid areas

Quantifying the spatial and temporal distribution of natural groundwater recharge is usually a prerequisite for effective groundwater modeling and management. As flow models become increasingly utilized for management decisions, there is an increased need for simple, practical methods to delineate recharge zones and quantify recharge rates. Existing models for estimating recharge distributions are data intensive, require extensive parameterization, and take a significant investment of time in order to establish. The Wisconsin Geological and Natural History Survey (WGNHS) has developed a simple daily soil–water balance (SWB) model that uses readily available soil, land cover, topographic, and climatic data in conjunction with a geographic information system (GIS) to estimate the temporal and spatial distribution of groundwater recharge at the watershed scale for temperate humid areas. To demonstrate the methodology and the applicability and performance of the model, two case studies are presented: one for the forested Trout Lake watershed of north central Wisconsin, USA and the other for the urban-agricultural Pheasant Branch Creek watershed of south central Wisconsin, USA. Overall, the SWB model performs well and presents modelers and planners with a practical tool for providing recharge estimates for modeling and water resource planning purposes in humid areas.

---

Resumen La cuantificación de la distribución espacial y temporal de la recarga natural de agua subterránea es un requisito previo para una modelación y una gestión efectivas de las aguas subterráneas. Dado que se está incrementando el uso de los modelos de flujo para la toma de decisiones de gestión, existe una necesidad creciente de métodos simples y prácticos para delimitar las zonas de recarga y cuantificar los rangos de la misma. Los modelos existentes para la estimación de la distribución de la recarga requieren datos intensivos, una parametrización extensiva y una inversión de tiempo significativa para ser establecidos. El Servicio Geológico y de Historioa Natural de Wisconsin (WGNHS) ha desarrollado un modelo simple de balance diario de agua en el suelo (SWB) que usa de forma sencilla datos disponibles de suelo, de cobertera, topográficos y climáticos conjuntamente con un Sistema de Información Geográfica (GIS) para estimar la distribución espacial y temporal de la recarga de aguas subterráneas a escala de cuenca para zonas templadas húmedas. Para demostrar la metodología, aplicabilidad y el comportamiento del modelo, se presentan dos casos: uno en la cuenca boscosa de Trout Lake, en la zona Norte-Central de Wisconsin, USA y el otro en la Cuenca urbano-agrícola de Pheasant Branch Creek, Sur-Centro de Winconsin, USA. En conjunto, el modelo SWB funciona bien y presenta a los modeladores y planificadores una herramienta práctica para llevar a cabo una estimación de la recarga para propósitos de modelación y planificación de los recursos de agua en zonas húmedas.

---

Résumé Quantifier les distributions temporelle et spatiale de la réalimentation naturelle des eaux souterraines est en règle générale un préalable à une modélisation et une gestion efficaces des eaux souterraines. Etant donné que les modèles numériques sont utilisés de manière croissante dans les prises de décisions en matière de gestion, il existe un besoin accru pour des méthodes simples et pratiques, afin de délimiter les zones d’alimentation et de quantifier les recharges associées. Les modèles existants, destinés à l’estimation de la répartition des réalimentations, demandent énormément de données, un paramétrage long, et un investissement conséquent en temps de mise en œuvre. Le Wisconsin Geologic and Natural History Survey (WGNHS) a développé un modèle simple basé sur un bilan en eau quotidien dans les sols (SWB); il utilise les données directement disponibles sur les sols, l’occupation des sols, la topographie et le climat, en conjonction avec un Système d’Information Géographique, afin d’estimer les distributions temporelle et spatiale de la réalimentation des eaux souterraines à l’échelle du bassin versant, pour les zones humides tempérées. Afin de démontrer la méthodologie, l’applicabilité et les performances du modèle, deux applications sont présentées: la première sur le bassin versant boisé de Trout Lake au centre-nord du Wisconsin (Etats-Unis), et le second sur le bassin versant agricole et urbanisé de Pheasant Branch Creek au centre-sud du Wisconsin. Le modèle SWB se comporte globalement bien, et offre aux modélisateurs un outil fonctionnel pour estimer les réalimentations, dans le cadre de modélisations et de plans de gestion des ressources en eau souterraine dans les zones humides.

     

基于强度折减的土质边坡破坏及稳定分析

边坡的破坏过程是由土体局部破坏向整体失稳发展的过程,其塑性区的开展及其水平位移增量的变化较完美地展现了这个过程。根据边坡的实际破坏和有限元数值模拟情况,提出了以特征点位移增量的突变及塑性区贯通作为边坡的失稳判断准则;并以此为判据,采用基于强度折减的大变形有限元方法分析了土质边坡的破坏及稳定性。研究表明,采用强度折减有限元法可有效分析边坡的破坏及其稳定性;此外还分析了带有软弱夹层黏土边坡的破坏性状及其稳定性,并比较了大、小变形有限元的计算结果,结果表明,带有软弱夹层黏土边坡的破坏性状随软弱夹层土体性质的变化而变化,由大小变形有限元分析得到的边坡稳定安全系数较为一致,但边坡的破坏机制随软弱夹层土体性质变化的转变点不同。     

粘性土微观结构简易定量分析法

作者根据计算机图像处理的基本原则，探索出一套粘性土微观结构简易定量分析法，经检验，这种方法简易，有效，对推广岩土结构定量化具有重要意义。     

A simple model for calculating tsunami flow speed from tsunami deposits

This paper presents a simple model for tsunami sedimentation that can be applied to calculate tsunami flow speed from the thickness and grain size of a tsunami deposit (the inverse problem). For sandy tsunami deposits where grain size and thickness vary gradually in the direction of transport, tsunami sediment transport is modeled as a steady, spatially uniform process. The amount of sediment in suspension is assumed to be in equilibrium with the steady portion of the long period, slowing varying uprush portion of the tsunami. Spatial flow deceleration is assumed to be small and not to contribute significantly to the tsunami deposit. Tsunami deposits are formed from sediment settling from the water column when flow speeds on land go to zero everywhere at the time of maximum tsunami inundation. There is little erosion of the deposit by return flow because it is a slow flow and is concentrated in topographic lows. Variations in grain size of the deposit are found to have more effect on calculated tsunami flow speed than deposit thickness. The model is tested using field data collected at Arop, Papua New Guinea soon after the 1998 tsunami. Speed estimates of 14 m/s at 200 m inland from the shoreline compare favorably with those from a 1-D inundation model and from application of Bernoulli's principle to water levels on buildings left standing after the tsunami. As evidence that the model is applicable to some sandy tsunami deposits, the model reproduces the observed normal grading and vertical variation in sorting and skewness of a deposit formed by the 1998 tsunami.     

土钉墙-锚杆支护技术模型试验及有限元研究

土钉复合土锚杆支护技术是对单一土钉墙技术的发展与改进,该方法具有施工简便,工期短,造价低廉等独特优点。虽然该方法已在工程中应用广泛,但土钉与土锚杆的复合支护的理论却还不完善。因此很有必要开展土钉墙复合土锚杆的模型试验,以加深对土钉与土锚杆复合支护体系的认识。通过多组模型试验,研究了在不同加载位置以及不同施工阶段下土钉的内力分配,基坑土体的位移场分布,不同加载位置下土钉及锚杆的支护效果等。结果表明：当超载较大且靠近基坑坑壁时,易出现直线型的滑动面,而超载距离坑壁较远,则较易出现圆弧状滑动面;锚杆对于控制滑动面出现有较强的作用,因此当超载靠近坡面时应将锚杆布置在坡面中上部,超载离坡面较远时,应布置在坡面下部