Synthesis and characterization of poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers

Poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. The reaction was carried out under mild conditions, using dicyclohexylcarbodiimide as the coupling agent and dimethylaminopyridine as the catalyst. The resulting copolymers were characterized by various analytical techniques, such as GPC, viscometry, ¹H‐NMR, FTIR, DSC, X‐ray diffractometry, and contact angle measurement. The results indicated that these copolymers presented outstanding properties pertinent to biomedical use, including better miscibility between the two components, low crystallinity, and hydrophilicity. Moreover, the properties of the copolymers can be modulated by adjusting the block length of the two components or the reaction conditions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1729–1736, 2002; DOI 10.1002/app.10580     

Synthesis and characterization of poly(oxyethylene)–poly(caprolactone) multiblock copolymers

Novel poly(oxyethylene)/poly(caprolactone) POE/PCL copolymers were synthesized by step growth polymerization of poly(ε-caprolactone) diols and poly(ethylene glycol) diacids using dicyclohexylcarbodiimide as coupling agent. The reaction was performed at room temperature and yielded multiblock copolymers with predetermined POE and PCL block lengths. The resulting copolymers were characterized by various analytical techniques including SEC, IR, ¹H NMR, DSC and X-ray diffractometry. Data showed that the properties of these polymers can be modulated by adjusting the chain lengths of the macromonomers. In particular, one or two crystalline structures can exist within the copolymers of various crystallinities. © 1998 SCI.     

Synthesis and properties of hydrophilic segmented block copolymers based on poly(ethylene oxide)‐ran‐poly(propylene oxide)

The present article discusses the synthesis and various properties of segmented block copolymers with random copolymer segments of poly(ethylene oxide) and poly(propylene oxide) (PEO‐r‐PPO) together with monodisperse amide segments. The PEO‐r‐PPO contained 25 wt % PPO units and the segment presented a molecular weight of 2500 g/mol. The synthesized copolymers were analyzed by differential scanning calorimetry, Fourier transform infra‐red spectroscopy, atomic force microscopy and dynamic mechanical thermal analysis. In addition, the hydrophilicity and the contact angles (CAs) were studied. The PEO‐r‐PPO segments displayed a single low glass transition temperature, as well as a low PEO crystallinity and melting temperature, which gave enhanced low‐temperature properties of the copolymer. The water absorption values remained high. In comparison to mixtures of PEO/PPO segments, the random dispersion of PPO units in the PEO segments was more effective in reducing the PEO crystallinity and melting temperature, without affecting the hydrophilicity. Increasing the polyether segment length with terephthalic groups from 2500 to 10,000 g/mol increased the hydrophilicity and the room temperature elasticity. Furthermore, the CAs were found to be low 22–39° and changed with the crosslink density. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci 117:1394–1404, 2010     

Hydrolytic degradation of poly(oxyethylene)–poly-(ε-caprolactone) multiblock copolymers

The degradation of poly(oxyethylene)–poly(ε-caprolactone) (POE–PCL) multiblock copolymers was investigated at 37°C in a 0.13M, pH 7.4 phosphate buffer selected to mimic in vivo conditions. The copolymers were obtained by coupling polycaprolactone diols and poly(ethylene glycol) diacids using dicyclohexylcarbodiimide as coupling agent. Various techniques, such as weighing, size exclusion chromatography, infrared, ¹H nuclear magnetic resonance, differential scanning calorimetry, and X-ray diffractometry, were used to monitor changes in total mass, water absorption, molar mass, thermal properties, degree of crystallinity, and composition. The results showed that introduction of POE sequences considerably increased the hydrophilicity of the copolymers as compared with PCL homopolymers. Nevertheless, the degradability of PCL sequences was not enhanced due to the phase separation between the two components. Significant morphological changes were also observed during the degradation. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 989–998, 1998     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Synthesis and characterization of star‐shaped poly(ethylene glycol)‐block‐poly(L‐lactic acid) copolymers by melt polycondensation

Compared with linear diblock or triblock poly(ethylene glycol)‐block‐poly(L ‐lactic acid) copolymer (PEG‐b‐PLLA), star‐shaped PEG‐b‐PLLA (sPEG‐b‐PLLA) copolymers exhibit smaller hydrodynamic radius and lower viscosity and are expected to display peculiar morphologies, thermal properties, and degradation profiles. Compared with the synthesis routine of PEG‐b‐PLLA form lactide and PEG, the traditional synthesis routine from LA and PEG were suffered by the low reaction efficiency, low purity, lower molecular weight, and wide molecular weight distribution. In this article, multiarm sPEG‐b‐PLLA copolymer was prepared from multiarm sPEG and L ‐lactic acid (LLA using an improved method of melt polycondensation, in which two types of sPEG, that is, sPEG₁ (four arm, Mn = 4300) and sPEG₂ (three arm, Mn = 3200) were chosen as the core. It was found the molecular weight of sPEG‐b‐PLLA could be strongly affected by the purity of LLA and sPEGs, and the purification technology of vacuum dewater and vacuum distillation could help to remove most of the impurities in commercial available LLA. The polymers, including sPEG and sPEG‐b‐PLLA with varied core (sPEG₁ and sPEG₂) and LLA/sPEG feeding ratios, were characterized and confirmed by ¹H‐NMR and ¹³C‐NMR spectroscopy, Fourier transform infrared spectroscopy (FT‐IR) and gel permeation chromatography, which showed that the terminal hydroxyl group in each arm of sPEGs had reacted with LLA to form sPEG‐b‐PLLA copolymers with fairly narrow molecular weight distribution. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Water vapor transmission of poly(ethylene oxide)‐based segmented block copolymers

This article discusses the rate of water vapor transmission (WVT) through monolithic films of segmented block copolymers based on poly(ethylene oxide) (PEO) and monodisperse crystallisable tetra‐amide segments. The polyether phase consisted of hydrophilic PEO or mixtures of PEO and hydrophobic poly(tetramethylene oxide) (PTMO) segments. The monodisperse tetra‐amide segments (T6T6T) were based on terephthalate units (T) and hexamethylenediamine (6). By using monodisperse T6T6T segments the crystallinity in the copolymers was high (～ 85%) and, therefore, the amount of noncrystallised T6T6T dissolved in the polyether phase was minimal. The WVT was determined by using the ASTM E96BW method, also known as the inverted cup method. By using this method, there is direct contact between the polymer film and the water in the cup. The WVT experiments were performed in a climate‐controlled chamber at a temperature of 30°C and a relative humidity of 50%. A linear relation was found between the WVT and the reciprocal film thickness of polyether‐T6T6T segmented block copolymers. The WVT of a 25‐μm thick film of PTMO₂₀₀₀‐based copolymers was 3.1 kg m^?2 d^?1 and for PEO₂₀₀₀‐based copolymers 153 kg m^?2 d^?1. Of all the studied copolymers, the WVT was linear related to the volume fraction of water absorbed in the copolymer to the second power. The results were explained by the absorption‐diffusion model. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide) and poly(propylene oxide)

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide (PEO) and poly(propylene oxide) (PPO) was evaluated by building up temperature-concentration phase diagrams. We have studied bifunctional triblock copolymers (HO-PEO-PPO-PEO-OH) and monofunctional diblock copolymers (R-PEO-PPO-OH and R-PPO-PEO-OH, where R length is linear C₄ and C_12–14). The cloud points of the polymer solutions depended on EO/PO ratio, polarity, R length and position of the hydrophilic and hydrophobic segments along the molecule. Such factors influence on the solutions behavior was also analyzed in terms of critical micelle concentration (CMC), which was obtained from surface tension vs. concentration plots. Salts (NaCl and KCl) added into the polymer solutions change the solvent polarity decreasing the cloud points. On the other hand, the cloud points of the polymer solutions increased as a hydrotrope (sodium p-toluenesulfonate) was added. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1767–1772, 1997     

Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

High molecular weight poly( -lactide) and poly(ethylene oxide) blends: thermal characterization and physical properties

The miscibility of high molecular weight poly( -lactide) PLLA with high molecular weight poly(ethylene oxide) PEO was studied by differential scanning calorimetry. All blends containing up to 50 weight% PEO showed single glass transition temperatures. The PLLA and PEO melting temperatures were found to decrease on blending, the equilibrium melting points of PLLA in these blends decreased with increasing PEO fractions. These results suggest the miscibility of PLLA and PEO in the amorphous phase. Mechanical properties of blends with up to 20 weight% PEO were also studied. Changes in mechanical properties were small in blends with less than 10 weight% PEO. At higher PEO concentrations the materials became very flexible, an elongation at break of more than 500% was observed for a blend with 20 weight% PEO. Hydrolytic degradation up to 30 days of the blends showed only a small variation in tensile strength at PEO concentrations less than 15 weight%. As a result of the increased hydrophilicity, however, the blends swelled. Mass loss upon degradation was attributed to partial dissolution of the PEO fraction and to an increased rate of degradation of the PLLA fraction. Significant differences in degradation behaviour between PLLA/PEO blends and (PLLA/PEO/PLLA) triblock-copolymers were observed.     

Crystal structure of the poly(ethylene oxide)–p-nitrophenol molecular complex

A crystalline complex of poly(ethylene oxide) (PEO) and p-nitrophenol (PNP) was studied by differential scanning calorimetry, X-ray diffraction, and FTIR spectroscopy, The phase diagram of this system is characterized by a peritectic reaction, and reveals the formation of a new crystal form different from those of PEO, and PNP. The triclinic unit cell of the complex was determined from the X-ray diffraction patterns of differently oriented samples obtained by mechanical deformations or spherulitic crystallizations. Finally, the molecular packing and the conformation adopted by the PEO chains were determined by FTIR spectroscopy. Polarization measurements have shown that the aromatic rings are very nearly normal to the c parameter (chain axis) and that the 1–4 axes of PNP molecules are parallel to the a^* reciprocal parameter (spherulitic growth direction). Finally, a new (t₂ gt₂ gt₃) conformation is proposed for the PEO chains on the basis of a normal mode analysis and the calculation of the intramolecular energy.     

Synthesis of multiblock copolymers of poly(2‐vinylpyridine) and polyoxyethylene

Telechelic dihydroxy poly(2‐vinylpyridine) (THPVP) samples with different molecular weights were synthesized by using lithium α‐methylnaphthalene as an anionic initiator in mixed solvents of benzene and tetrahydrofuran (THF). Then multiblock copolymers of poly(2‐vinylpyridine) (P2VP) and polyoxyethylene (PEO) were obtained by condensing THPVP and PEO with dichloromethane in the presence of potassium hydroxide. The effects of reaction time, molecular weight of PEO and THPVP, and raw meal ratio PEO/THPVP (w/w) were investigated. The best conditions were found. The copolymers can be purified by water and toluene. The purified copolymers were characterized by infrared (IR) and ¹H nuclear magnetic resonance (¹H‐NMR). The PEO segment content was calculated from the integral curve of ¹H‐NMR spectra. The results showed that these multiblock copolymers were connected through oxymethylene. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1632–1636, 2003     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of comb‐like polymer PVC–poly(ethylene oxide)

A new series of amphiphilic graft‐copolymers, composed of poly(vinyl chloride) (PVC) backbones and poly(ethylene oxide) side chains, was synthesized by chemical modification of PVC. The synthesis was based on the reaction between chlorine in PVC (polymerization degree 700) and sodium salt of polyethylene glycol (PEG). PEGs with molecular weights of 200 and 600 were used. The graft polymers were characterized by IR and gel permeation chromatography and the molecular parameters such as the average numbers of grafting chains on the PVC backbones were calculated as well as the grafting percent. The molecular weights of PEG were found to influence the rate of the grafting reaction and the final degree of conversion. The maximum grafting percentage of the resulted polymers after the purification was ca. 34%, regardless of the molecular weight of PEG. No gel was observed in the PVC‐g‐PEOs, in spite of the average numbers of grafting chains up to 32. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 475–479, 2000     

Study on the properties of crosslinking of poly(ethylene oxide) and hydroxyapatite–poly(ethylene oxide) composite

This study covers the crosslinking of poly(ethylene oxide) (PEO) and its composite with calcium hydroxyapatite (HA), their mechanical and swelling properties, and morphology. Sheets of the composites of PEO (two different grades with M_v: 5 × 10⁶ and 2 × 10⁵) and HA and neat PEO were prepared by compression molding. The prepared composite and PEO (0.1‐mm‐thick) sheets were crosslinked with exposure of UV‐irradiation in the presence of a photoinitiator, acetophenone (AP). This simple method for crosslinking, induced by UV‐irradiation in the presence of AP, yielded PEO with gel content up to 90%. Gel content, equilibrium swelling ratio, and mechanical and morphological properties of the low molecular weight polyethylene oxide (LMPEO)–HA crosslinked and uncrosslinked composites were evaluated. Although the inclusion of HA into LMPEO inhibits the extent of crosslinking, the LMPEO–HA composite with 20% HA by weight shows the highest gel content, with appreciable equilibrium swelling and mechanical strength. The growth of HA in simulated body fluid solutions on fractured surfaces of LMPEO and also LMPEO–HA was found to be very favorable within short times. The dimensional stability of these samples was found to be satisfactory after swelling and deposition experiments. The good compatibility between the filler hydroxyapatite and poly(ethylene oxide) makes this composite a useful tissue‐adhesive material. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 488–496, 2003     

Comparison of micelles formed by amphiphilic poly(ethylene glycol)‐b‐poly(trimethylene carbonate) star block copolymers

In this article, we describe the synthesis and solution properties of PEG‐b‐PTMC star block copolymers via ring‐opening polymerization (ROP) of trimethylene carbonate (TMC) monomer initiated at the hydroxyl end group of the core PEG using HCl Et₂O as a monomer activator. The ROP of TMC was performed to synthesize PEG‐b‐PTMC star block copolymers with one, two, four, and eight arms. The PEG‐b‐PTMC star block copolymers with same ratio of between hydrophobic PTMC and hydrophilic PEG segments were obtained in quantitative yield and exhibited monomodal GPC curves. The amphiphilic PEG‐b‐PTMC star block copolymers formed spherical micelles with a core–shell structure in an aqueous phase. The mean hydrodynamic diameters of the micelles increased from 17 to 194 nm with increasing arm number. As arm number increased, the critical micelle concentration (CMC) of the PEG‐b‐PTMC star block copolymers increased from 3.1 × 10^?3 to 21.1 × 10^?3 mg/mL but the partition equilibrium constant, which is an indicator of the hydrophobicity of the micelles of the PEG‐b‐PTMC star block copolymers in aqueous media, decreased from 4.44 × 10⁴ to 1.34 × 10⁴. In conclusion, we confirmed that the PEG‐b‐PTMC star block copolymers form micelles and, hence, may be potential hydrophobic drug delivery vehicles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization of poly(ethylene oxide) in i-polypropylene–poly(ethylene oxide) blends

A two-stage stable system of isotactic polypropylene–poly(ethylene oxide) blend, in which poly(ethylene oxide) can be permanent either in molten or in crystallized states in the temperature range from 280 to 327 K, was described. The behavior of that blend was explained in terms of fractionated crystallization. A fine dispersion of poly(ethylene oxide) inclusions is required for efficient suppression of crystallization initiated by heterogeneous nuclei. The application of a thin film of polypropylene-poly(ethylene oxide) 9 : 1 blend obtained by quenching for multiuse erasable and rewritable carriers for visible information has been demonstrated. The same sample exhibits different dynamic mechanical properties when poly(ethylene oxide) inclusions are molten or crystallized. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2047–2057, 1997     

Ultraviolet-induced crosslinking of solid poly(ethylene oxide)

Poly(ethylene oxide) (PEO) of molecular weight from 200,000 to 2,000,000 was crosslinked by exposure to ultraviolet radiation with a high-pressure 150 W mercury lamp. Photochemical crosslinking of PEO proceeds in the presence of photoinitiators such as benzophenone and acetophenone which act as a hydrogen-abstracting agent. Gel fraction yield exceeds 90%, and the number-average molecular weight between crosslinks determined by equilibrium swelling in chloroform varies from 3,000 to 100,000. The degree of crosslinking can be controlled by changing the irradiation temperature. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2299–2307, 1997     

Biodegradable and photocurable multiblock copolymers with shape‐memory properties from poly(ε‐caprolactone) diol,poly(ethylene glycol), and 5‐cinnamoyloxyisophthalic acid

Biodegradable and photocurable multiblock copolymers of various compositions were synthesized by the high‐temperature solution polycondensation of poly(ε‐caprolactone) (PCL) diols of molecular weight (M_n) = 3000 and poly(ethylene glycol)s (PEG) of M_n = 3000 with a dichloride of 5‐cinnamoyloxyisophthalic acid (ICA) as a chain extender, followed by irradiation by a 400 W high‐pressure mercury lamp (λ > 280 nm) to form a network structure. The gel contents increased with photocuring time, reaching a level of over 90% after 10 min for all copolymers without a photoinitiator. The thermal and mechanical properties of the photocured copolymers were examined by DSC and tensile tests. In cyclic thermomechanical tensile tests, the photocured ICA/PCL/PEG copolymer films showed good shape‐memory properties at 37–60°C, with both shape fixity ratio and shape recovery ratio over 90% at a maximum tensile strain of 100–300%. The water absorption of these copolymers and their rate of degradation in a phosphate buffer solution (pH 7.0) at 37°C increased significantly with increasing PEG content. The novel photocured ICA/PCL/PEG multiblock copolymers are potentially useful in biomedical applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Enhanced dynamic mechanical and shape‐memory properties of a poly(ethylene terephthalate)–poly(ethylene glycol) copolymer crosslinked by maleic anhydride

Dimethyl terephthalate (DMT) and ethylene glycol (EG) were used for the preparation of poly(ethylene terephthalate) (PET), and poly(ethylene glycol) (PEG) was added as a soft segment to prepare a PET–PEG copolymer with a shape‐memory function. MWs of the PEG used were 200, 400, 600, and 1000 g/mol, and various molar ratios of EG and PEG were tried. Their tensile and shape‐memory properties were compared at various points. The glass‐transition and melting temperatures of PET–PEG copolymers decreased with increasing PEG molecular weight and content. A tensile test showed that the most ideal mechanical properties were obtained when the molar ratio of EG and PEG was set to 80:20 with 200 g/mol of PEG. The shape memory of the copolymer with maleic anhydride (MAH) as a crosslinking agent was also tested in terms of shape retention and shape recovery rate. The amount of MAH added was between 0.5 and 2.5 mol % with respect to DMT, and tensile properties and shape retention and recovery rate generally improved with increasing MAH. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 27–37, 2002