Examination of selected synthesis parameters for wood adhesive‐type urea–formaldehyde resins by 13C NMR spectroscopy. III

The varying polymer structures of wood adhesive‐type urea–formaldehyde resins resulting from different formaldehyde/first urea (F/U₁) mole ratios used in the first step of resin manufacture were investigated using ¹³C. As the F/U₁ mole ratio decreased progressively from 2.40 to 2.10 and to 1.80, the viscosity increase due to polymerization during resin synthesis became faster and resulted in decreasing side‐chain branches and increasing free urea amide groups in the resin structure. The resultant UF resins, with the second urea added to an overall F/(U₁ + U₂) of 1.15, showed viscosity decreases when heated with stirring or allowed to stand at room temperature that were also characteristic with the F/U₁ mole ratios used in resin synthesis. The formaldehyde emission levels of particleboards bonded with the freshly made UF resins showed relatively small but similarly characteristic variations. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2800–2814, 2001     

Examination of selected synthesis parameters for typical wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. II

A particleboard adhesive‐type urea–formaldehyde (UF) resin was made at a formaldehyde ratio of 2.10 and added with a second urea at low temperature to the typical final formaldehyde/urea ratio of 1.15. Time samples taken during heat treatments of the resin sample up to 70°C over a period of 250 min showed decreases in Type II/IIi hydroxymethyl group content, accompanied with decreases in resin sample viscosity and increases in formaldehyde emission of bonded particleboards. The results indicate that various hydroxymethyl groups of polymeric UF resin components migrate to the second urea to form Type I hydroxymethyl groups. Time samples taken during the room‐temperature storage of the resin sample over a period of 1 month behaved similarly initially, but in the later stage, some polymerization progressed, shown by increases in viscosity and methylene and methylene–ether group contents. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1243–1254, 2000     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. V

The effects of posttreatments of particleboard adhesive‐type urea–formaldehyde resins were studied. The resins were synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.40, 1.60, 1.80, 2.10, and 2.40 and then the second urea was added to give a final formaldehyde/urea ratio of 1.15 in alkaline pH. The resins were posttreated at 60°C for up to 13.5 h and the 2.5‐h heat‐treated resin samples were stored at room temperature for up to 27 days. Resins sampled during the posttreatments were examined by ¹³C‐NMR and evaluated by bonding particleboards. In the posttreatments, hydroxymethyl groups on the polymeric resin components dissociated to formaldehyde and reacted with the second urea, and methylene and methylene–ether groups were formed from reactions involving the second urea. Methylene–diurea and urea groups bonded to UF polymers were identified. As a result, the viscosity of the resins initially decreased but later increased along with the cloudiness of the resins. Bond‐strength and formaldehyde‐emission values of particleboard varied with posttreatment variables as well as with the F/U₁ mol ratios used in the resin syntheses. The results would be useful in optimizing resin synthesis and handling parameters. Various reaction mechanisms were considered. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1896–1917, 2003     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999     

Optimizing the conditions of quantitative 13C-NMR spectroscopy analysis for phenol–formaldehyde resol resins

The experimental time of ¹³C-NMR quantitative analysis of phenol–formaldehyde resins was reduced so that quantitativeness was maintained. The quantitative spectra of 14 model resins were obtained using a gated decoupling technique suppressing the NOE. The paramagnetic additive, Cr(acac)₃, was used to shorten relaxation times of carbon atoms. The use of Cr(acac)₃ was optimized in two deuterated solvents, DMSO and acetone. To reach short relaxation times and further the measurement times, the concentration of relaxation reagent, the delay time, and the number of NMR scans were optimized. Quantitativeness was proved by analyzing the spectra of accurate mixture of model compounds, and the spectra of the condensed model resins. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1805–1812, 1998     

On the correlation equations of liquid and solid 13C‐NMR,thermomechanical analysis,Tg, and network strength in polycondensation resins

Wide‐scope mathematical relationships have been established between the ¹³C‐NMR of liquid polycondensation resins, such as urea–formaldehyde and phenol–formaldehyde resins, and the strength of the network formed by the same resin when hardened under well‐defined conditions, the thermomechanical analysis deflection, the number average molecular mass and the number of degrees of freedom of the average polymer segment between crosslinking nodes in the hardened resin network, the resin network glass transition temperature, its solid‐phase ¹³C‐NMR proton‐rotating frame spin‐lattice relaxation time, and the homogeneous and heterogeneous polymer segment/polymer segment interfacial interaction energy calculated by molecular mechanics. These mathematical relationships allow the calculation of any of these parameters from any of the techniques listed, provided that all of the systems are used under well‐defined conditions. Under different conditions, the values of the numerical coefficients involved change; and, whereas the equations are still valid, a different set of coefficients needs to be recalculated. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1703–1709, 1999     

Resorcinol–formaldehyde reactions in dilute solution observed by carbon‐13 NMR spectroscopy

A recently discovered coupling agent, hydroxymethylated resorcinol (HMR), based on resorcinol–formaldehyde, can greatly enhance wood‐to‐epoxy resin bond durability in exterior applications. However, for HMR to be most effective, it needs to be prepared a few hours before it is applied to the wood surface. In this study, carbon‐13 nuclear magnetic resonance (NMR) spectroscopy was used to monitor composition of HMR as a function of time to characterize which chemical groups are present in solution when HMR is applied. A quantitative assessment of formaldehyde‐derived groups required the use of 99% ¹³C‐enriched formaldehyde. Hydroxymethyl groups, primarily attached to the 4‐position of resorcinol, and hemiformal groups formed very quickly. Signals from methylene linkages between resorcinol rings began to appear 20 min into the reaction. Formaldehyde was consumed quickly; 95% was bound to resorcinol rings within 1.7 h. By 3 h, 16% had been converted to methylene linkages, and by 8.3 h, 40% was converted. Another set of NMR experiments was used to monitor the dependency of peak positions of resorcinol solution as a function of pH. These experiments showed significant effects, especially between pH 7.7 and 9.1, which explains chemical shift changes observed during the HMR reaction. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1760–1768, 2000