Low-temperature ordering of L10 FePt phase in FePt thin film with AgCu underlayer

FePt (20 nm) films with AgCu (20 nm) underlayer were prepared on thermally oxidized Si (0 0 1) substrates at room temperature by using dc magnetron sputtering, and the films annealed at different temperature to examine the disorder–order transformation of the FePt films. It is found that the ordered L1₀ FePt phase can form at low annealing temperature. Even after annealing at 300 °C, the in-plane coercivity of 5.2 kOe can be obtained in the film. With increase in annealing temperature, both the ordering degree and coercivity of the films increase. The low-temperature ordering of the films may result from the dynamic stress produced by phase separation in AgCu underlayer and Cu diffusion into FePt phase during annealing.     

Magnetic properties of Fe/Pt films by symmetrical insertion of Ag

Ultrathin Ag (0.5 nm) pinning layers (APLs) were symmetrically inserted into [Fe/Pt] bilayers to introduce controllable defects on the interfaces between Ag and Fe/Pt multilayers. The highest coercivity 7700 Oe and remanent squareness 0.95 were obtained with five APLs. The large enhancement in coercivity (75% increment compared with that without APL) is due to the relative uniform defects that introduced pinning effects on the interfaces between the APLs and Fe/Pt multilayers. According to the distribution of angule- dependent coercivity of Fe/Pt multilayers without and with APLs, a tendency is suggested of weakened domain-wall motion while enhanced rotation of reverse domain mode.     

Structural and magnetic properties of SmCo7−xMox alloys

Phase structure and magnetic properties of the as-cast and as-milled/annealed SmCo_7−xMo_x (x=0, 0.1, 0.2, 0.3, 0.4) alloys have been systematically studied. It is found that all the as-cast series alloys are composed of the CaCu₅-type and Th₂Zn₁₇-type phases. Saturation magnetization of the samples decreases with the Mo content increasing. Intrinsic coercivities (_iH_c) of no more than 0.06 T are observed in these as-cast samples, due to their rather coarse grain microstructures with an average grain size of 50 μm. The as-milled/annealed SmCo_7−xMo_x powders crystallize in the disordered TbCu₇-type (1:7) structure with very fine nanograins, and a minor Co₃Mo phase appears in the samples with x=0.1-0.4. High _iH_c (?0.95 T) are achieved in these samples, with a maximum of 1.26 T located at x=0.2, which can be primarily attributed to strong pinning of the domain wall motion at the nanograin boundaries. The temperature coefficient (β) of the _iH_c is about −0.22%/°C in the temperature range of 25-400 °C for the as-milled/annealed samples.     

Microstructures and coercivities of SmCox and Sm(Co,Cu)5 films prepared by magnetron sputtering

We have investigated the influence of composition and annealing conditions on the magnetic properties and microstructural features of SmCo_x films that were prepared by sputtering and subsequent annealing. A huge in-plane coercivity of 5.6 T was obtained from an optimally annealed Sm–Co film, which was attributed to the nanometer sized polycrystalline microstructure of the highly anisotropic SmCo₅ phase. Although a high density of planar defects were observed in the films that were annealed at high temperatures, they did not act as strong pinning sites for domain wall motion. The effect of Cu on [SmCo_4.5(9 nm)/Cu(xnm)]₁₀ multilayer thin films was also studied. An appropriate Cu content increased the coercivity.     

Magnetic losses evolution of a semi-processed steel during forced aging treatments

An ultra-low carbon steel (30 ppm after decarburization) containing Al and Si was aged for distinct soaking times at 210 °C. The core loss increased continuously until around 24 h. After that, only slight changes were verified. It was found that only the hysteresis loss component changed during the aging treatment. By internal friction test and transmission electron microscopy it was seen that carbon precipitation caused the magnetic aging. By scanning electron microscopy it could be concluded that the increase of aging index was attributed to the high number of carbides larger than 0.1 μm.     

Growth temperature dependence of the hysteretic behavior of Ni0.5Zn0.5Fe2O4 thin films

Herein, a discussion of the effect of deposition temperature on the magnetic behavior of Ni_0.5Zn_0.5Fe₂O₄ thin films. The thin films were grown by r.f. sputtering technique on (1 0 0) MgO single-crystal substrates at deposition temperatures ranging between 400 and 800 °C. The grain boundary microstructure was analyzed via atomic force microscopy (AFM). AFM images show that grain size (φ∼70-112 nm) increases with increasing deposition temperature, according to a diffusion growth model. From magneto-optical Kerr effect (MOKE) measurements at room temperature, coercive fields, H_c, between 37and 131 Oe were measured. The coercive field, H_c, as a function of grain size, reaches a maximum value of 131 Oe for φ ∼93 nm, while the relative saturation magnetization exhibits a minimum value at this grain size. The behaviors observed were interpreted as the existence of a critical size for the transition from single- to multi-domain regime. The saturation magnetization (21 emu/g<M_s<60 emu/g) was employed to quantify the critical magnetic intergranular correlation length (L_c≈166 nm), where a single-grain to coupled-grain behavior transition occurs. Experimental hysteresis loops were fitted by the Jiles-Atherton model (JAM). The value of the k-parameter of the JAM fitted by means of this model (k/μ_o∼50 A m²) was correlated to the domain size from the behavior of k, we observed a maximum in the density of defects for the sample with φ∼93 nm.     

Recent development of non-oriented electrical steel sheet for automobile electrical devices

This paper describes non-oriented electrical steel sheet for automobile motors and reactors. Electrical steel sheets for energy efficient motors show high magnetic flux density and low iron loss. They are suitable for HEV traction motors and EPS motors. A thin-gauge electrical steel sheet and a gradient Si steel sheet show low iron loss in the high-frequency range. Therefore, the efficiency of high-frequency devices can be greatly improved. Since a 6.5% Si steel sheet possesses low iron loss and zero magnetostriction, it contributes to reduce the core loss and audible noise of high-frequency reactors.     

An intercomparison of rotational loss measurements in non-oriented Fe–Si alloys

We report a comparison of rotational energy loss measurements in the same non-oriented Fe–Si laminations carried out by two laboratories Istituto Nazionale di Ricerca Metrologica (INRiM) in Torino, Italy and Wolfson Centre for Magnetics (WCM) in Cardiff, United Kingdom. The measurements were performed on disk samples at magnetizing frequencies between 5 and 200 Hz with controlled circular flux density loci ranging between 0.2 and 1.9 T. Energy loss was measured applying both the fieldmetric and the rate-of-rise of temperature methods. The latter, exploiting the rate of rise of temperature under quasi-adiabatic conditions, is conveniently adopted on approaching magnetic saturation. Results from the two laboratories agree well up to 1.4 T, despite the different physical principles of the fieldmetric vs. rate-of-rise of temperature methods and the different size of sample and measuring areas. The rate-of-rise of temperature method seems to be the natural approach at high induction values.     

Hysteresis loss subdivision

Assuming that different energy dissipation mechanisms are at work along hysteresis, a hysteresis loss subdivision procedure has been proposed, using the induction at maximum permeability (around 0.8 T, in electrical steels) as the boundary between the “low-induction” and the “high-induction” regions. This paper reviews the most important results obtained in 10 years of investigation of the effect of microstructure on these components of the hysteresis loss. As maximum induction increases, the “low-induction loss” increases linearly up to 1.2 T, while the “high-induction loss” is zero up to 0.7 T and then increases as a power law with n=5. Low-induction loss behavior is linearly related to H_c between 0.4 and 1.2 T. Grain size has a larger influence on low-induction losses than on high-induction losses. Texture has a much stronger influence on high loss than on low-induction loss, and it is related to the average magnetocrystalline energy. 6.5%Si steel shows smaller hysteresis loss at 1.5 T than 3.5%Si steel only because of its smaler high-induction component. The abrupt increase in hysteresis loss due to very small plastic deformation is strongly related to the high-induction loss component. These results are discussed in terms of energy dissipation mechanisms such as domain wall movement, irreversible rotation and domain wall energy dissipation at domain nucleation and annihilation.     

Magnetic losses at high flux densities in nonoriented Fe–Si alloys

We present and discuss power loss measurements performed in Fe–(3.5 wt%)Si nonoriented laminations up to very high flux densities. The results are obtained on disk samples using a 1D/2D single-sheet tester, where the fieldmetric and the thermometric methods are applied upon overlapping polarization ranges. The power loss in the highest polarization regimes (e.g. J_p>1.8 T) is measured, in particular, by the rate of rise of temperature method, both under controlled and uncontrolled flux density waveform, the latter case emulating the conditions met in practical unsophisticated experiments. Lack of control at such extreme J_p levels is conducive to strong flux distortion, but the correspondingly measured loss figure can eventually be converted to the one pertaining to sinusoidal induction at the same J_p values. This is demonstrated as a specific application of the statistical theory of magnetic losses, where the usual formulation for the energy losses in magnetic sheets under distorted induction is exploited in reverse fashion.     

Comparative evaluation of performance of percolated perpendicular media using FePt–MgO/Pt/Cr trilayer and FePt–MgO/MgO bilayer

(Fe₄₈Pt₅₂)_100−x–(MgO)_x films were used to examine the performance of a perpendicular percolated medium. Two underlayers, Pt(0 0 1)/Cr(0 0 2) and MgO(0 0 2), were used for comparison. The (Fe₄₈Pt₅₂)_100−x–(MgO)_x film with the MgO underlayer exhibits a strong preference to segregate at FePt grain boundaries. The microstructure with small closely packed MgO particles (2–4 nm) dispersed uniformly in the L1₀ FePt matrix was achieved in the Pt/Cr underlayered sample. Structural data reveal that the precipitate is crystallographically coherent with the surrounding L1₀ FePt phase and preserves good lattice alignment. Magnetic results indicate significant pinning behavior for those introduced non-magnetic columns with an enhanced coercivity of about 70%—much greater than that of the MgO underlayered samples. Percolated perpendicular medium can be realized in the FePt system and a Pt(0 0 1)/Cr(0 0 2) underlayer promotes the formation of pinning sites within the FePt grains.     

Multiphased (NaCl)x(KCl)y−x(KBr)1−y single crystals: ac conductivity activation energy versus bulk properties

The ac electrical measurements have been just reported for alkali halide mixed crystals that were melt grown from NaCl, KCl and KBr starting materials. They showed a nonlinear variation of all the electrical parameters with the bulk composition. In this short paper, we show that these mixed systems, depending on their major constituent, are classified into three categories in each of which, the activation energy for the ac conductivity increases linearly with BΩ, where B is the isothermal bulk modulus and Ω the mean volume per atom. In addition, the resulting three straight lines are formed to have almost the same slope.     

Hysteresis loss component under non-sinusoidal flux waveforms

Separation of total energy dissipation per magnetisation cycle into a frequency-dependent dynamic component and a frequency-independent hysteresis component is a common practise in evaluating electromagnetic losses in Si–Fe electrical steel sheet. The assumed frequency-independent hysteresis component is defined by a coefficient C₀ (J/kg). In this work, the value of C₀ was determined using a linear extrapolation method and quasi-static hysteresis energy loss per cycle. The extrapolation method gave a considerable error when applied to non-sinusoidal excitation voltages (pulse width modulation and square) in a frequency range from 25 to 100 Hz. For this reason the coefficient values obtained from the quasi-static measurements at 0.01 Hz were assumed.     

On the Steinmetz hysteresis law

The behavior of the Steinmetz coefficient has been described for several different materials: steels with 3.2% Si and 6.5% Si, MnZn ferrite and Ni–Fe alloys. It is shown that, for steels, the Steinmetz law achieves R²>0.999 only between 0.3 and 1.2 T, which is the interval where domain wall movement dominates. The anisotropy of Steinmetz coefficient for non-oriented (NO) steel is also discussed. It is shown that for a NO 3.2% Si steel with a strong Goss component in texture, the power law coefficient and remanence decreases monotonically with the direction of measurement going from rolling direction (RD) to transverse direction (TD), although coercive field increased. The remanence behavior can be related to the minimization of demagnetizing field at the surface grains. The data appear to indicate that the Steinmetz coefficient increases as magnetocrystalline anisotropy constant decreases.     

Curie temperatures and crystallization behavior of amorphous Fe81−xNixZr7B12 (x=10, 20, 30, 40, 50, 60) alloys

Curie temperature, crystal structure and crystallization behavior of amorphous alloys with the stoichiometry Fe_81−xNi_xZr₇B₁₂ (x=10–60) have been studied by X-ray diffractometry (XRD), differential scanning calorimetry (DSC) and AC-magnetization (TMAG) measurements as functions of temperature. The thermal stability of long-range magnetic order, T_C vs. Ni content in as-quenched amorphous alloys exhibits maximum at 352 °C for x=40. The primary crystallization has been detected during annealing at the first crystallization stage of all ribbons investigated.     

Magnetic properties and power losses in Fe–Co-based bulk metallic glasses

Magnetic properties of Fe–Co-based bulk metallic glasses have been experimentally investigated. Samples were prepared by water-cooled Cu-mold injection casting technique. The samples have cylindrical shapes with 0.8 mm diameter and 30 mm length. Amorphous structures were confirmed by the presence of a main halo in X-ray diffraction patterns and by the detection of crystallization signal around 650 °C using differential scanning calorimetry.     

Structure and magnetic properties of SmCoxTi0.4-1:7 ribbons

SmCo_xTi_0.4 (x=6.6, 7.1, 7.6, 8.1) ribbons have been prepared by melt spinning at a wheel speed of 42 m/s, followed by annealing at 750 °C for 2 h. Both as-spun and as-annealed ribbons possess the disordered TbCu7-type (1:7) phase even when the Sm/(Co,Ti) atomic ratio deviates from 1/7. The c/a ratio increases with increasing Co concentration x, but the unit cell volume decreases. The Curie temperatures show above 700 °C, increasing from 707 °C for x=6.6 to 782 °C for x=8.1. The saturation magnetizations increase almost linearly with increasing Co content. The observed magnetic hardening is believed to arise from the high magnetocrystalline anisotropy of the 1:7 phase and the fine nanograin structure. The intrinsic coercivity of 9797 Oe has been obtained in the melt-spun SmCo_7.1Ti_0.4 ribbons.     

Thermomagnetic transitions and coercivity mechanism in bulk composite Nd60Fe30Al10 alloys

The thermomagnetic behaviour (within the temperature range 553-300 K) for the bulk composite Nd₆₀Fe₃₀Al₁₀ alloy is described in terms of a transition from paramagnetic to superferromagnetic state at T=553 K, followed by a ferromagnetic ordering for T<473 K. For the superferromagnetic regime, the alloy thermomagnetic response was associated to a homogeneous distribution of magnetic clusters with mean magnetic moment and size of 1072 μ_B and 2.5 nm, respectively. For T<473 K, a pinning model of domain walls described properly the alloy coercivity dependence with temperature, from which the domain wall width and the magnetic anisotropy constant were estimated as being of ≈8 nm and ≈10⁵ J/m³, typical values of hard magnetic phases. Results are supported by microstructural and magnetic domain observations.     

Magnetic viscosity-coercivity relation for Fe1−xCox fine particles

The variation of the applied field results in a subsequent change of magnetization with time. There is a relationship between the coercivity (H_c), as the equilibrium characteristic of the system, and its magnetic stability (1/S), as a parameter characterizing the time dependence. 1/S as a function of H_c has been measured and studied for different Fe_1−xCo_x samples. We synthesized several samples with different values of x by applying various magnetic fields during the grains’ growth, and observed a linear relationship between 1/S and H_c.